Search Documents

The paper outlines the development and objectives of the slim core (50 mm dia.) testing procedures employed at the Company's Central Research Laboratories with particular reference to washability studies required for coalfield evaluation. It shows that when the routine test procedures, that have been developed for cores recovered form the Sydney Coal Basin, were applied to Bowen Basin Coals some of the washing data obtained appeared to be suspect. Though yield indications appeared to be of the right order, product ash, required separating gravity and percentage of near gravity material were found to be at variance with bulk washability data. The results of a correlation study made on an underground seam from the Bowen Basin comparing slim core, hulk sample, and pilot plant washing data are given. The results of a series of studies including washability studies made on slim cores, strip samples, large diameter cores and bulk samples, pilot washing trials and computer simulations of washery circuits treating Lilyvale seam coal from the Bowen Basin are shown.

Jan 1, 1977

Blasting effectiveness must be gauged by total production costs. ANFO charges made up in polythene "sausages" are not as profitable as is indicated by the price of ANFO. All-slurry charges are warranted only where blastholes cannot be dewatered effectively, or where drilling costs are very high. An increase in blasthole diameter leads to coarser fragmentation. This effect is most pronounced in tough and massive or blocky strata, or in ground which consists of unfissured boulders in a softer matrix. When ANFO and some slurry-type charges of small diameter are used in plastic-acting ground, charges may fail to detonate through precompression by charges fired on an earlier delay. The optimum blasthole length is rarely less than four times the burden distance. For best results, blastholes should be inclined to the vertical and parallel to the face. Nominal burdens and spacings are often altered radically by the initiation sequence. For best fragmentation, all blastholes must have good effective faces, and should be effectively stagg- ered with an actual spacing:burden ratio in the approximate range 2.0-5.0.

Jan 1, 1975

Methods of measuring the frictional properties of rock surfaces, both by direct sliding and in triaxial apparatus, are described. It was found that for some rocks the coefficient of friction remains reasonably constant as sliding is continued but for others it increases considerably.The effect of fluid pressure in the surface of sliding was found in all cases to be adequately represented by the effective stress criterion. Some observations on sliding on two conjugate planes showed that the motion on the two planes may be very different, depending on small differences in the constraints.The coefficients of friction of natural open joints in bore core were found to lie in the comparatively narrow range 0.32 to O.68 although surface coatings were very diverse.A set of diagrams on the equal area projection is given which enables a rapid determination to be made of those planes on which sliding is possible in a given three-dimensional stress field. The influence of the intermediate principal stress on this is of considerable importance.

Jan 1, 1969

Drill and blast operations account for 12 - 15 per cent of total mining costs. This paper looks at a comparison between electronic detonators and non-electric detonators, focusing on the cost benefits associated with the high precision of the timing sequences of electronic detonators. An analysis of the total mining costs was made on two main case studies; one on a quarry in South Australia (Martin, 2007) and the other on a project undertaken at Sunrise Dam (Vaughan et al, 2007). The criteria used in the analysis included; the resulting fragmentation, a vibration analysis, crusher throughput and productivity analysis such as excavator cycle times, dig rates of the excavator and bucket fill factor. The results indicate that there were consistent production improvements and hence reductions in total mining costs attributed to the use of electric detonators. An increase in the degree of fragmentation gives lower crushing costs as more material passes through as undersize. This reduces truck delay time at the crusher, which in turn gives higher truck and shovels productivity as well as higher dig rates for the excavators.

Jan 1, 2008

The word governing derives from gubernare meaningto pilot a ship. Being inclined to metaphors, one could be forgiven to think that politicians act this verb and captain the Nation's ship into some definite course. In the case of at least the mineral resources industry, it seems that there are not many James Cook followers in our parliaments: Australia's approach to mineral and energy policy is often chaotic - witness the 1935 to 1961 ban on iron ore export-ing which prevented the development of a significant steel industry at time when the World was hungry for this metal, just to mention one amongst many other examples.The follies of Australia's mineral policies are well il-lustrated in the case of uranium mining. Although Australia had the Western World's largest economic reserves of uranium, it is onlythefifth producing nation and its uranium potential is largely unrealised. At the root of this situation are the interventionist attitudes and policies of successive Federal Governments which for more than four decades distorted the Investment decision and, in more recent times. discouraaed investment.

Jan 1, 1990

By A Benedictus, A Butcher, J Wikstr÷m, B Lindblom, E Rutqvist

LKAB is a mining company situated in northern Scandinavia, manufacturing blast furnace- and direct-reduction pellets and sinter fines. Pellet development at LKAB comprises testing at laboratory and pilot scale. The LKAB Experimental Blast Furnace (EBF) is a unique test facility and an important tool in terms of product development and process research. For a better understanding of pellet behaviour in the blast furnace process, LKAB has started to use automated mineralogy for the characterisation and quantification of its iron ore products and pellets. A mineralogical evaluation of iron ore olivine pellets, taken from a test campaign in the EBF, has been performed. The studied materials were samples from excavated pellet layers through the entire EBF at different positions. A large number of iron ore pellets was analysed using a combination of automated mineralogy, using QEMSCAN«, and chemical analysis. Important information about the performance of pellets in the blast furnace process, such as a quantitative description of mineral and iron oxide alterations at different temperatures, Fe-reduction and alkali deposition, was obtained.

Jan 1, 2008

Pulverised coal firing was pioneered in the cement industry prior to the turn of the century. Ash from the coal is absorbed into the mix in the kiln and replaces secondary materials. With high purity limestone coal with high ash content can be used. Fuel cost is a major part of the total manufacturing cost. Cement plants are thus quick to respond to fuel price changes and will use low grade fuels if there is a price advantage. Combustion conditions in a cement kiln differ markedly from a boiler. Flame length is determined by air/fuel mixing but because of fixed secondary air conditions this depends on primary air momentum. Volatile content has some effect on flame length but this can be offset by coal fineness. Much of the heat for cement production is for limestone calcination which is a low grade energy requirement. By allowing long residence time in separate direct fired vessels which then feed the high temperature kiln the energy of materials such as oil shale, tyres and lump lignite can be utilised.

Jan 1, 1987

In underground ore mining of copper ore, lead-zinc ore, tin ore and fluorspare in German Democratic Republic geological situation is characterized by ore deposits of small thickness and great variability of ore grades and mining conditions. For long range mining strategy and short-term planning of production a model was developed fitting to make optimal economic mining decisions. Starting point of the model is a cost function representing all direct costs per unit recoverable metal in concentrate for each stoping unit (ore reserve block). In the costs function the results of regression analysis of ore grade and metal recovery in concentration plant were considered. All stoping units (ore reserve blocks) of a mine were arranged to growing direct costs. The relationships of recoverable metal, ore tonnages and corresponding costs were plotted in a diagram. The data processed by- computer and the graphic representation of the results make possible 1. economic evaluation of stopes and ore reserve blocks, 2. estimation of cut off grade, 3. optimization of works planning.

Jan 1, 1977

By G J. Sparrow, M J. Fisher-White

A mineral and chemical characterisation study was conducted on ilmenite-rich heavy mineral concentrates sourced from the western sector of the Eucla Basin in southern Australia. Test work involved using X-ray diffraction (XRD), scanning electron microscope (SEM) and electron microprobe-based characterisation methods. Results showed considerable variability in the degree of ilmenite alteration between deposits with TiO2 contents varying from 53 - 63 wt per cent TiO2. Notwithstanding variability between individual deposits, the samples all had [Ti]/[Ti+Fe] ratios >0.5 consistent with a mineral assemblage of hydrated ilmenite or the hydrated, Ti-rich alteration phase pseudorutile (Fe3+2-x Ti3O9-3x (OH)3x). Accessory phases consisted of rutile (primary and secondary), zircon, aluminosilicates, quartz, Fe oxyhydroxides and spinels. Results for the most altered material are broadly comparable with data for ilmenite concentrates from the eastern margin of the basin. The mineralogy of the western Eucla Basin concentrates and the minor element composition of the ilmenite grains suggest they could be upgraded to synthetic rutile by a modified Becher process.

Jan 1, 2008

In an earlier paper(l) details of a laboratory method of extracting and separating tantalum and columbium oxides from tantalite have been given. In view of the fact that Australia may have need to be self sufficient in this field it was decided to erect a pilot plant for the production of tantalum oxide in the Metallurgy School, University of Melbourne. The plant was designed for treating about 40 lb. of ore in a batch over a period of two weeks, although; because of the sectionalized nature of the process, the capacity of the plant was 40 lb. ore per week.Australia is fortunate in possessing some very rich tantalite and columbite deposits, particularly in the Pilbara District in Western Australia. The ore used in this work was obtained from a small but high grade deposit near Greenbushes, Western Australia, and consisted of lumps, weighing up to 8 lb. each, of almost pure ferro-tantalite with occasional thin veins of the very' rare' mineral stibiotantalite.The main constituents were:

Jan 1, 1946

By Muir D

A review of the various methods of degrad- ing cyanide either from gold processing liquors or electroplating baths is presented with some discussion on their relative merits or problems. Whilst alkaline chlorination is common practice in many U.S. and Canadian plants it poses particular problems for certain plants. Alter- native methods include electrolysis, hydrolysis and air oxidation with activated carbon as catalyst which are also integral steps in the carbon-in-pulp process. A basic study of the degradation of cyanide ion has been carried out therefore to determine the effect of temperature, oxygen and carbon. It is shown that carbon is an excellent catalyst for degradation by air and likely to lead to higher losses of cyanide in a C.I.L. circuit. Degradation by hydrolysis is important at high temperatures and high pH such as employed in the Pressure Zadra or Anglo elution processes. Carbon catalysed degradation of cyanide by oxygen in effluent streams may be an environmentally acceptable alternative to conventional chlorine degradation.

Jan 1, 1987

Australia had an active uranium mining industry in the 1950s with uranium oxide being supplied under contract to the atomic energy authorities of the U.K. and U.S.A. In the 1960s, when these con- tracts concluded, domestic production ceased, apart from Rum Jungle, whose production until 1971 was stockpiled. By the 1970s, the demand for uranium from the electrical utility industry had risen sharply and the effects on Australia were notable. The Mary Kath- leen mine re-opened in 1976 but, more significantly, exploration activity suddenly expanded with the re- sult that several world-standard deposits were locat- ed. Western world requirements for uranium based on increasing energy consumption and a changing energy mix, will warrant the development of Aust- ralia's resources. By 1985 our mines could be pro- ducing 9,500 tonnes of uranium oxide yearly and by 1995 the export value from uranium could reach that from wool. In terms of benefit to the community the economic rewards are considerable but, in terms of providing energy to the world, Australia's uranium is vital.

Jan 1, 1978

By Tullemans FJ

This paper describes the general approach to ore reserve estimation and mine planning used at the Kidston Gold Mine. The geological setting and exploration is briefly summarized for background information.A geostatistical study of the deposit was carried out to determine the geological ore reserve. This was confirmed using a manual polygonal technique. Optimum pits outlined by a Lerchs-Grossman open pit design algorithm were manually smoothed allowing mineable reserves to be calculated. Mine production schedules based on kriged block grades and tonnages are continuously updated using production blasthole assays. An arithmetic mean technique of block grade estimation has proved successful to date. After milling approximately 4.9Mt of ore, the mill grade of 2.13g Au/t is only 0.5% above the mine estimate of 2.12g Au/t. The difference in contained gold between "As staked" blasthole reserves and kriged mineable reserves is 3.8%. The application of blasthole kriging as a basis for ore/waste classification in erratically mineralized areas is being evaluated. Planned future developments are briefly mentioned.

Jan 1, 1986

By Rynn J. M W, Paynter A

Recent studies by the authors have concerned themselves with assessing the earthquake risk to north-eastern Australia, based on available historical earthquake data for the area. There have been several significant earthquakes (Richter local magnitudes of the order of 6) concentrated in the Wide Bay - Burnett region in central eastern Queensland, although none of these has occurred close to a significant centre of population or development. Using derived average acceleration attenuation relations and world-wide data on earthquake-induced damage as a basis, conditions under which earthquake-induced liquefaction may occur have been investigated and presented in graphical form. Historical earthquake data for north-eastern Australia have been overlain on this graphical presentation and it has been demonstrated that the Wide Bay - Burnett region, in particular, may in the past have been on the verge of earthquake-induced liquefaction, where ground conditions are susceptible. When this is viewed in the context of the rapid growth in population and development in this area over recent years, the risk can no longer be ignored with impunity.

Jan 1, 1990

By D Giles

We present plate tectonic reconstructions, showing that porphyry-type ore deposits are spatially and temporally linked to ridge subduction. A reconstruction of the Peruvian subduction system reveals an immediate metallogenic response to the arrival of the Nazca Ridge at the subduction trench, followed by southward migration of the zone of metallogenic activity due to the lateral migration of the zone of ridge subduction. A similar pattern is recognised in central Chile , where the spatio-temporal distribution of giant ore deposits coincides with the arrival of the Juan Fernandez hotspot chain at the subduction zone. We conclude that there is a spatial and temporal link between ridge subduction and ore deposit formation, with high metal fluxes concentrated in zones of ridge subduction. Thus, the recognition of tectonic patterns associated with ridge subduction can provide insights into predictive mineral discovery by enhancing our ability to predict the position of large mineral deposits in other modern and ancient orogens. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By J M. Palin

Hydrothermal scheelite precipitated in fault-veins at Paradise, Bonnie Jean, Davidson's and Glenorchy mines display chemical variability involving REE patterns that are transitional between two end-member types. Type I is a MREE-enriched pattern with no or a small positive Eu anomaly. Type II is a flat to MREE-depleted pattern with a strong positive Eu anomaly. The chemical inhomogeneity of these scheelites can be explained by a model of fractional precipitation of REE, with preferential removal of MREE from the fluid during precipitation of scheelite. Irrespective of the mechanism responsible for scheelite precipitation, the source of dissolved constituents is different for scheelites from the Paradise Mine. Bonnie Jean, Davidson's and Glenorchy scheelites formed from LREE-enriched fluids whereas Paradise scheelites precipitated from fluids that were lower in LREE. These inferred fluid characteristics cannot be linked unambiguously to specific source rocks in the region, but could suggest that scheelite deposited in the Paradise fault-vein reflects a more mafic source of REE possibly greenschists, whereas the REE in scheelite from the other mines suggest a more felsic source.

Jan 1, 2003

By Still RF

Sintering of lead and zinc concentrates is practised by Sulphide Corporation Pty. Limited to provide both desuiphurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulphur dioxide gas for sulphuric acid manufacture. From November, 1969 a 20 percent increase in production rate has been obtained through improvements in operating technique. A gradual increase in bed permeability was achieved by modifications to the feed mix conditioning equipment and by improving moisture control. However advantage could not be taken of the higher permeability to increase sulphur elimination because the hardness of the lump sinter decreased. Higher throughput, better quality sinter and more stable sintering conditions were however made possible by simultaneously: 1. reducing segregation and compaction in the sinter bed, by narrowing the discharge opening of the main layer feed hopper, 2. reducing the sizing of sinter returns to give a closer size spectrum of particles in the feed mix, and 3. increasing the sulphide sulphur content of the feed mix to give higher bed Temperatures.

Jan 1, 1972

The firing of mass blasts at Isa Mine is a normal operating practice. Both electric and non-electric initiating systems are being used for this purpose. The advantages gained by large firings relate to the Planning, Scheduling, Services and Production functions of Isa Mine. More efficient us"e is made of manpower due to the concentrated charging effort and con- tinuity of the charging operation. In addition, the requirement for ring firing personnel to work at the edge of large stope voids is reduced. Better fragmentation results from the interaction of adjacent detonating rings of blastholes and in flight collisions. With mass blasts there is also less chance of large blocks of ore, created by faults or joints, falling into the stope and creating problems at the drawpoints. The formation of a large tonnage of broken ore facilitates production at scheduled rates from that stope source. The weight of explosive detonating during a mass blast can be considerable. Isa Mine has achieved satisfactory blasting results without excessive ground vibration levels and present knowledge indicates that pillar ground stab- ility has been maintained.

Jan 1, 1978

By Singh JK, Singh R

With a view to producing increased target output every year, Indian coal mining industry is fast moving towards mechanisation but the present approach of mechanisation suffers from lack of standardisation, mainly due to nonavailability of the cutting data for various machine/rock combinations. The coal seams of the country are relatively hard in nature and the coaling machines are reported to be affecting production and productivity of the coal mine and the very trend of niechanisation. This paper presents the result of extensive study performed to visualise the cutting characteristics of coal seams of compressive strength ranging from 20 MPa to 65 NIPa. In a specially designed drag bit type coal plough rig, continuous recording of cutting forces was done with the help of a microprocessor based data logger and the specific energy of cuttability was evaluated at different depth of cut and speed of cutting. The geomechanical properties such as compressive strength, orientation and frequency of cleats etc. and different indices of coal seams were measured in the laboratory and field and relationship was developed for easy determination of specific energy.

Jan 1, 1992

By Kyle J. H, Misra V. N

The most recent development in gold processing is the increasing use of heap leaching for the extraction of gold from low grade ore, and old tailings dumps. The reason for this trend is mainly to do with economics. The advantage of heap leaching is the considerable saving in both capital and operating costs. However, not all ores are amenable to heap leaching. It is only applicable to well oxidized ores that have suitable permeability char- acteristics, and the gold recovery is poorer than by conventional process. In this study, an attempt has ben made to ascertain the heap leaching characteristics of Western Australian gold ores on the bench scale using multiple, appropriately sized leach columns. The influence of particle size, flow rate, column depth and leaching time on the rate of gold extraction was determined. The percolation rate of cyanide leaching solution was deter- mined with and without gypsum additions. Efforts were also made to minimise particle segregation, fines migration and solution channelling during leaching, so as to improve solution percolation, gold extraction rate and recovery.

Jan 1, 1991