Search Documents

By Nightingale RJ

A column (50 cm 4) provided with a bell charging mechanism and a rectangular perspex insert was used to investigate the inter-relationship between charging pattern, size analysis and velocity profile for a number of charging methods. It is shown that a strong correspondence exists between size distribution and velocity profile for bell charged ore and coke and that decreased coke volumes cause higher pressure drops and increased central flow in beds with "V" shaped layers. It is also shown that a bell charged mixed burden exhibits greater segregation than when it is bell charged as layers and that when uniformly charged the mixed burden shows least segregation and a virtually flat velocity profile. A relationship is derived for "V" profile charges showing the extent of central segregation with furnace size.

Jan 1, 1975

This paper describes the programing and specification requirements which affected the choice of excavation methods on the Melbourne Underground Rail Loop (M.U.R.L.). The various methods that were chosen are briefly described, and the three most used are compared in more detail. Excavation rates, cycle times and other statistics are compared for full face tunnel boring, full face drill and blast, and heading and bench using a road header excava- ting machine. The length of tunnel excavated is sufficient to enable meaningful statistics to be presented and the significant specifi- cation and geological factors are described to weight the statistics where necessary for purposes of comparison. Average tender prices are given for excavation and primary support to indicate the reimbursement sought by contractors to carry out this type of tunnelling.

Jan 1, 1981

By Enever J, Walton R, Wold M

Photoelastic and equivalent material model ling techniques for studying stresses and defor- mations and modes of failure in geological and engineering structures are described. The appli- cation of these techniques to the solution of tunnelling design problems is outlined. Models may contain heterogeneous components to simulate geological and man-made structures and may be two- or three-dimensional. Prototype construc- tion procedures and time dependent behaviour may be modelled. Examples of recent model studies carried out for the design of underground railway tunnels are given. Development of photoelastic and equi- valent material modelling techniques and facili- ties at the CSIRO, Division of Applied Geomech- anics are described, including a biaxial and triaxial frame for testing large scale two and three dimensional equivalent material models and components of full scale prototype structures.

Jan 1, 1976

By Mutmansky J. M, Organiscak J, Qin J, Bhaskar R

The results of a two-year research study into the relationship between quartz dust levels in host material and in respirable dust in continuous mining sections are presented in this paper. The experimental design and sampling procedures for underground data collection are outlined. The sample analysis procedures for quartz determination, the analysis results and conclusions of the study are discussed.

Jan 1, 1988

Weinberg, born and educated in Germany, worked in'the American West for 10 years as a mining engineer and metallurgist. He was the first head of the Queensland Smelting Co. and from 1889 through 1915 was a prominent mining figure in Queensland. He was a competent manager at Aldershot, Dapto, and Chillagoe, but always lacked huge ore deposits for his smelters.

Jan 1, 1985

Following the `Poseidon boom' of the early-1970s, there was pressure for development of a national body of company law and for the introduction and development of legislation to regulate the securities industry, including the Stock Exchange, trading in securities and securities dealers and advisers.After 20 years, the Corporations Law emerged in effect as Commonwealth legislation implemented automatically by the States.

Jan 1, 1997

By Tilyard P. A

Recent exploration has established depos its of nickel sulphide in several areas of Western Australia. To assist in their develop- ment Amdel has investigated the beneficiation of many samples from these deposits and has estab- lished flowsheets for the recovery of nickel values by flotation. Metallurgical data are presented for the samples according to four factors which were encountered in their respective treatments.

Jan 1, 1973

By C Chen, W J. Bruckard, F R. A Jorge

The base metal industry mines and processes hundreds of million tonnes of ore per annum to produce saleable products and large tonnages of waste by-products such as tailings. These ores usually contain less than 1 wt per cent of toxic elements (As, Sb, Bi, Cd, Se, Te, Hg, etc), which are subsequently treated with the other components in the ore during the production of concentrate through to saleable metal products. The deportments of minor elements across the various unit operations of a process flow sheet do not normally receive the attention that the major elements receive. However, these minor elements can have a major influence on the quality of the products as well as an economic and environmental impact. Therefore, a high degree of control over their deportments is a key step in reducing their dispersion in the biosphere. Ongoing work at CSIRO has been examining minor element deportments across unit processes used for smelting and refining and the options for early removal of minor elements, as well as methods for safe disposal of some toxic elements. This paper provides an overview of the R&D activities undertaken at CSIRO to develop tools and methodologies for improved management of minor elements during the processing of sulfide ores.

Jan 1, 2006

When a joint venture is established between a major and a minor, the co-venturers often have a number of divergent interests; the major may have put up significantly more capital into the project and will want to protect its investement; the major may have more financial resources and be more readily to commit capital to the project; the major may have more technical resources and expertise to provide to the project; the major may have other competing demands for its capital; the minor may be relying on rapid development of the project as its sole source of cash flow. Successful joint ventures arise when the co-venturers understand each others' interests and attempt to satisfy these interests. This could be achived by having a clear process and timetable for development of the project coupled with clear rules for distribution of income, the commitment of capital to the project and the provision of inter-company services. If divergent interests are either regulated clearly or eliminated, both co-venturers are more likely to seek common objectives in the joint venture with less scope for conflict. This paper, written from the perspective of a major, examines means of establishing successful joint ventures between majors and minors.

Jan 1, 1997

The development of reliable and accurate solution sampling systems plus on-line atomic absorption spectrophotometers and voltammetric analysers at Pasminco Metals - EZ's (PMEZ) zinc refinery at Hobart, Tasmania, has led to extensive implementation of On-Stream Analysis (OSA) throughout the hydrometallurgical circuit. These systems complement industrial autotitrator and colorimetric analysers and with the comprehensive use of a powerful integrated Distributed Control System (DCS), provide extensive monitoring and control of all the important in solution' parameters for the plant. Samples can be left unaltered, or filtered or settled, to remove solids. They are then precision diluted and pneumatically transported to analyser shelters, where they are analysed for zinc, acid, copper, cadmium, lead, antimony, cobalt, nickel, mercury and ferrous, ferric and/or total iron. The range of analyses depends on the sample itself. The results are used for feed forward and/or feedback control of reagents where possible, or simple trend monitoring and out-of-specification alarming when closed loop control is not practical. The overall system reliability and accuracy is such that many daily composite plant samples are no longer analysed off-line. Operator sampling has also been reduced, and in two places, autotitrators with automatic sample pre-treatment have been installed for preparing and analysing samples collected by operators.

Jan 1, 1993

By N J. Beukes, J Gutzmer, C Reinke, M Bau

In this study the light sparse phase search (SPL_Lt) mode on the Mineral Liberation Analyser (MLA) was successfully used to identify and quantify the abundance of rare earth element (REE) phosphates in Precambrian iron formations. Monazite (light REE phosphate) and xenotime (Y and heavy REE phosphate) are identified and data from the MLA combined with the mineral chemistry of the two minerals are used to calculate and model the expected REE concentration and distribution in these two REE phosphates. The REE phosphates account for up to 31 per cent of the REEs in the banded iron formations (BIFs) and excellent correspondence is observed between the modelled REE patterns and the whole rock geochemical data available for the same samples. Except for quantifying the mineral weights, the sparse phase search also allows for the localisation of REE phosphate grains and the observation of their association with other minerals using backscatter electron (BSE) imaging. These observations are used to conclude that the REE phosphates were most likely of diagenetic origin, with REEs and phosphate remobilised from primary chemical precipitates. It is demonstrated that automated mineralogical techniques can be used to qualitatively and quantitatively describe the influence of a rockÆs trace mineralogy on its geochemistry.

Jan 1, 2008

During the past decade geopolymer technology has emerged as a possible solution for the effective stabilisation and solidification of waste materials. Amorphous to semi-crystalline geopolymers form by the co-polymerisation of individual alumino and silicate species, which originate from the dissolution of silicon and aluminium containing source materials at a high pH in the presence of soluble alkali metal silicates. It has been shown previously that geopolymerisation can transform a wide range of waste alumino-silicate materials such as fly ash and blast furnace slag into building and mining products with excellent chemical and physical properties, including high compressive strength as well as fire and acid resistance. These chemical and physical properties suggest that geopolymeric matrices derived from waste materials are well suited for environmental and other applications such as the encapsulation of mine tails, the immobilisation of heavy metals and also the fabrication of structural products. The current challenge is to demonstrate that a wide variety of natural Al-Si minerals could serve as potential source materials for the synthesis of geopolymers. Moreover, it should be shown on a large commercial scale that it is possible to encapsulate waste materials into the geopolymeric structure without compromising the chemical and physical properties of the final product for the desired application.

Jan 1, 2000

Natural leaching of minerals has been recorded for some two millenia but surprisingly only in recent years has enough been known of the process for any serious design to be made. Copper has been recovered from natural mine waters since about the 17th century but again little progress was made in de- sign procedures until recently. Natural or dump leaching was started as a recovery process late in the 19th century and in the years up to the classic study of Taylor and Whelan in 1943 a series of impirical optimis- ations made it a valuable process for treating low grade or waste material. The biological nature of Sulphide leaching was proven by Colmer and Hinkle in 1947 and since then a large mass of data has accumulated on the microbiology, biochemistry, and response of ores to this form of attack. In spite of this knowledge and the vast amount of pract- ical experience available there are few recorded attempts to present methods of calculation or design procedures that can be used for setting up a leaching process. A framework is given here on which such procedures can be based and indications given of the inherent advantages and limitations of the process,

Jan 1, 1969

By J Ralston, G B. N Kaggwa, L Huynh

Three polymers of varying chemistries and molecular weights have been used to depress talc in a model sulfide ore consisting of talc, pentlandite, and chalcopyrite. Flotation testing revealed a distinct hierarchy of effectiveness of the polymers in the depression of talc (HP Starch > Polymer-H > Dextrin WY) but a different order of effectiveness for depression selectivity (Dextrin WY > Polymer-H > HP Starch). Adsorption isotherm determinations for the gangue and valuable mineral phases indicate that the differences in selectivity are partially due to adsorbed amount variations, with Dextrin WY adsorbing marginally less on the sulfides than Polymer-H. Contact angle measurements on packed particle beds have revealed that the polymers have differing abilities to reduce the contact angle of talc and the sulfide minerals. An explanation of the observed trends is given in terms of the binding mechanisms of the polymers on the talc and the sulfide mineral phases. Order of addition effects between collector and depressant were also investigated using adsorption isotherm determinations for the polymers in the presence of a pre-adsorbed layer of collector and vice versa. Adsorption of the polymers was not affected by the presence of the collector. Similar results were obtained for the adsorption of collector in the presence of pre-adsorbed layers of polymer.

Jan 1, 2005

At many locations in Australia the decommissioning of mining operations will require the disposal of excess water. If the water is contaminated its disposal may be restricted by government guidelines. The timing of water disposal may be critical to the schedule of close-out. The uncertainty of the annual rainfall input to the water storage and disposal system may determine the success or failure of close-out. The uncertainty associated with any outcome can be used to determine the reliability of the system, or inversely its risk. The technique of Monte Carlo simulation, using the uncertainty in annual rainfall, is applied to quantify the risks associated with water disposal as part of the requirements for close-out in two case studies. In both case studies it is assumed that water disposal is via evaporation only. The first case study is the Nabarlek operation, located about 270 km east of Darwin. This project is required to complete the engineering work associated with its close-out by December 1995. The second study investigates the situation of close-out for the Ranger Uranium Mine, about 250 km east of Darwin. It should be noted that the Ranger mine was examined as part of the annual update of its contingency rehabilitation plan and the probability of implementing the plan is extremely small. The probability of success for the Nabarlek case varied from less than ten per cent to greater than 95 per cent depending on the management strategy. Four possible strategies were investigated for the Ranger mine with the chance of success varying between 20 and 95 per cent. The estimation of the evaporation rate and the area allocated to evaporation was critical in both cases. By applying seasonally based evaporation pan coefficients determined on site, rather than an average monthly value of 0.75, the chance of success was improved by up to 35 per cent for Ranger. Simulation modelling is able to provide information on the likely response of mine water management systems and the level of risk. This information is required to efficiently plan and manage the disposal of water for close-out.

Jan 1, 1994

IN any assay office it is of paramount importance to keep the men interested in their work; and in order to do this, men on routine work, such as lead, zinc, and sulphur deterrrrinations, slag analysis, etc, should be changed around monthly. This gives some variety and helps to keep a man's interest on his work, so that better work results. It may be maintained that to keep a man on the same class of work indefinitely makes him more expert at his work. This is certainly true; but in assaying, where accuracy is so essential, it is absolutely necessary for a man to keep his mind on the work, and not 'get' into a mechanical method of working. He is also on the alert to discover means for shortening his analytical methods, and his capacity forwork is increased. Another advantage is that the men get a good all-round training, and one is never at a loss to replace a man on any class of work when he is absent from any cause. This tends to smoother and more efficient running of the assay department. In industrial assaying it is often advantageous to have a result quickly, so that it will be of maximum benefit in the running of some part of the plant, In such a case it pays to sacrifice a little accuracy to speed up a method. The shortest method is less costly, and a quick approximate method is all that is required to give the superintendent the requisite information. Time is thereby saved, and the cost is less. In carrying out assaying for any large industrial plant, such as a smelting works, there is always a tendency for superintendents running the different departments to send in more samples for assay than are absolutely necessary when no system of costing is in operation. Some of these samples may involve a lot of work and heavy expenditure, as, for example, the estimation of only one impurity in a sample of refined lead. If the superintendent knows that the cost of assaying all samples sent in by,him is charged up directly against...

Jan 1, 1922

The issue of flyrock is critical to the operation of all mineral extraction sites that use blasting. This paper takes a risk-based approach to identifying, analysing and managing the flyrock hazard. The basic cause of flyrock generation is a mismatch between the energy available and the work to be done. It should be noted that the energy available depends on the charge confinement. This mismatch can be caused by an abrupt decrease in rock resistance (geological weaknesses), overcharging, inadequate delays between holes and rows, inappropriate blast design and inaccurate drilling. The mismatch can come about from two sides; either too much energy (charge) for a fixed burden (work to be done), or insufficient burden (work to be done) for a fixed charge. The main mechanisms of flyrock generation are rifling, cratering, face bursting and secondary blasting. Each source mechanism has different characteristics in terms of vulnerable locations and each requires different control measures. However, all controls require a high level of quality control and assurance. A range of different approaches for managing flyrock risk and determining blast clearance zone dimensions are presented. A prescriptive consequence-based approach is discussed. A conventional risk matrix based approach is outlined with some innovation regarding controls rating and uncertainty ratings. A published semi-empirical approach is discussed. Two examples of quantitative flyrock risk analysis are presented; one involves bench blasting based on a published paper and the second is a cratering example developed by the author based on consulting projects. Finally, a stochastic approach based on published work is presented which simulates cratering superimposed on face bursting mechanisms. Also, a stochastic analysis undertaken by the author of the cratering example is presented. Effective blast emission management is required for two reasons; firstly to reduce and/or eliminate safety risks and secondly to manage public perception of blasting risks such as flyrock. The conclusion of the current research is that the wild flyrock risk can be estimated using existing techniques. Furthermore, both qualitative and quantitative risk management methods as discussed in this paper can be used for flyrock management for a given blasting situation. A combination of both is considered to be best practice.

Jan 1, 2007

By Conway KM

The traditional role of Australian Consultants in project development has been until recently restricted to the provision of discrete packages for survey and engineering services during the feasibility, design and construction phases of a project. Management of such projects was the province of the owner/developer or his agent. However, Australian Consultants are now being con- sidered for an expanded role on resources Projects.

Jan 1, 1983

The procedures for an audit and review process upon which continuous improvement programs may be based are described. The case for regular audits of mining operations to establish performance trends is advanced. Analysis of performance data using the parameters of the capacity equation used in conjunction with learning curves is described. The extrapolation of learning curves in performance target setting, operating and capital cost budgeting is advocated.

Jan 1, 1992

By James D, Dawson N

The alternate mineral dressing tech-niques for the production of ilmenite roaster feed from heavy mineral concentrate and the reasons for the selection of wet high intensity magnetic separation (WHIMS) at Richards Bay Minerals are outlined.Initial flowsheet studies were under-taken using laboratory scale equipment followed by on site pilot testing. Flowsheet development culminated with an extensive test programme conducted at Readings of Lismore in 1975.

Jan 1, 1986