Search Documents

By B Lumsden, R Smiles

Independence Group’s Jaguar Mine treats a polymetallic ore producing a copper concentrate and zinc concentrate. Effective separation of the sulfides requires relatively fine grinding with flotation feed P80 of about 75µm. Zn losses to final tails are greater than 60 per cent and <32 µm. When magnetic conditioning was first installed in 2010 it showed about an 8 per cent reduction of zinc in final tail and on some ores a similar benefit for silver as well. Current testwork is showing about a 12 per cent reduction in zinc and silver in final tail, consistent with the original testwork. Sizing of the final tail during the tests showed that the reduction of zinc and silver losses were only in the <32 µm fraction, as would be expected from an aggregation process. However, the most surprising result was about a 4 per cent reduction in zinc and silver in the plant feed with a >99 per cent statistical certainty. The reduction in zinc and silver in the feed is also only in the <32 µm fraction. Therefore, because the magnetic conditioning of Zn flotation feed cannot impact plant ore feed grade the hypothesis is that the magnetic conditioning is reducing the fine mineral from downstream processes, like filtering and thickening, returning to the plant feed in the recycled process water. This hypothesis is consistent with plant observation of dirty concentrate thickener overflow and measurements of solids in the overflow, as well as the average % Zn grade in cyclone overflow that correlates with the magnetic conditioning ON and OFF days. This paper presents these plant test results.CITATION:Smiles, R and Lumsden, B, 2018. Improving fine sulfide mineral recovery in Independence Group’s Jaguar Mine zinc circuit, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 433–440 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Ruschitzka C

The productivity and economic success of a German hard coal mine is attributed to the high productivity of a small number of operation points; however high rates of production are associated with increased gas emission at the working sites. Therefore modem high technology is required in order to reach the planned production rate, since high methane concentrations often cause unplanned breakdowns in operation. The optimised simulation of gas emission is a fundamental planning tool for mine design as well as for determining the potential of a coal deposit and has increased in significance over the last years. Methane-INFO enables the three-dimensional, graphical simulation of a working site taking account of different aspects such as the mine design, ventilation, production rate, geology, seam quality, gas exhaustion, etc. The following paper gives a short overview over the benefits of the discussed system.

Jan 1, 1995

The design of a sand pump is similar in principle to that of a water pump but differs in several areas. Results of experiments on sand pump performance have been summarized and values of design parameters quoted for optimum results. Typical performance data are also Included.

Jan 1, 1973

By Hossaini SMF

After reviewing the various approach es,namely, empirical,analytical.observational and numerical, a logical systematic approach is proposed for the estimation of compressive strength of coal pillars. In this approach first,uniaxial compressive strength of coal in pillars is estimated,taking into account the size effect and the effect of discontinuities. Next,the compressive strength of coal pillars is estimated by determining the stress distribution in the pillar and the Bieniawski strength criterion. The results appear to be compatible to the ones obtained by Wilson's method. The traditional pillar design equations give improper answers for deep workings.

Jan 1, 1991

"Cash flow modelling during project evaluation is enhanced when probabilistic methods are applied to the inputs. One of the important inputs is the quarterly production profile. Typically, the steady-state production profile provided to project evaluation practitioners is deterministic, with each quarter the same as every other quarter. This is unrealistic as actual production profiles from existing mines exhibit a range or quarter-on-quarter variance. Monte Carlo stochastic simulation of the production profile can be used to provide a range of possible outcomes, but how are these ranges selected? This paper describes the use of quarterly production variance from a large database of mines worldwide as a benchmark to inform the appropriate selection of ranges. The coefficient of variation is used to rank the production from mines, with quartile analysis applied to indicate industry best, median and worst variation. Due diligence of existing mines and evaluation of future production performance can be quantitatively assessed using this approach. Examples of the effect on value are provided.CITATION:Stewart, C A, 2016. Production variance benchmarks and their use in project evaluation and due diligence, in Proceedings Project Evaluation 2016, pp 201–213 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

Thermal Processing of Petroleum Fly Ash for Vanadium Recovery

Sep 13, 2010

This is the time of year tor the presidential address, and with the present incumbent engaged in the coal mining industry, it will therefore come as no surprise to you that the theme of my address this evening is concerned with coal.There are other reasons for this apart from my contact with the coal industry. At present, coal is supplying considerable overseas revenue at a time when the remainder of the mining market is in a somewhat depressed state. That times will change goes without saying, if history is to be believed.However, so far so good for coal. My first reaction when The Institute indicated its wish that I be president for 1976 was to become deeply conscious of the honour bestowed on me.On consideration, I realized that very few past presidents have been intimately connected with the coal mining industry to the extent of indulging in it for lengthy periods as a full time occupation or, conversely, a part time interest for a long time. It also appears that not one had started their career in the industry. In my case, 'also, there were 8 very interesting years ,as a gold miner and metallurgist before commencing in coal.It therefore seemed appropriate to endeavour to discover ,why this should be so, as coal mining is now a very important part of a very important industry. What were the reasons why the industry took so long to emerge when there were ample reserves of easily accessible coal?Frankie and Johnnie in their bar room epic of the depression years concluded, and I paraphrase, that "their story held no moral, their story told no tale". If my story has such a message, it could perhapsbe construed as reinforcing the oft-repeated dictums, true or false, that "history repeats itself" or "man never learns".Coal mining is by far our oldest major Australian industry except for agriculture. Its history is almost as old as that of settlement:For various reasons, there has been a glamour associated with metal mining ventures which prob...

Jan 1, 1976

By Gilbert DJ, Lemon NM

A case history of a two year study of low grade ores in the Middleback Range area with the objective of defining possible areas of interest from a combination of geological- petrological-metallurgical criteria. Covering the general geology of the area and ore types; the results of metallurgical testwork and the pattern of evolution of these tests; the petrological explanation of the results of the testwork; the culmination of the work in the selection of areas of best potential for more intensive work. Jaspilites consisting of magnetite, hematite and limonite with quartz and silicate-carbonate-sulphide minerals are hosts to high grade iron mineralisation but also constitute a large low grade iron Reserve.

Jan 1, 1975

By Hill J. R M, McDonald M. M

A prediction technique for support perfor- mance of hydraulic backfill in narrow stopes is applied to two stopes separated vertically by a sill pillar. Predicted stope wall closures and fill pressures compare favorably with field measurements taken over a period of several years at two mines in the Coeur d'Alene dis- trict. Stope wall closure and peak pillar stress can be substantially reduced by improved fill quality within a practicable range of fill and rock properties.

Jan 1, 1973

This paper deals with innovative techniques that have enabled personal computers to be used on the mine site to define, develop and manage an ore body resource, while being aware of the consequences to the environment. The same set of personal computer tools that are used for resource estimation, once the province of expensive workstations, can also be used by geologists, mining engineers, surveyors and environmentalists, in managing the whole mining process, including production, grade control, monthly reconciliation and stockpile management through to tailings the management, mine rehabilitation and the due diligence process of mine closure.

Jan 1, 1996

This study examines the application of Landsat TM data to the identification of hydro- thermal alteration in the arid terrain of the El Salvador region of north Chile. Numerical reflectance values were extracted from the digital Landsat TM data for a variety of rock surfaces, including four parts of the El Salvador gossan, for each of six spectral bands. These reflectance values were analysed statistically in order to select the three spectral bands, combined as a colour composite image, that are most efficient in discriminating different varieties of alteration and for general geolog- ical interpretation. The most cost effective com- posite image for this area is a combination of bands 1,4 and 7 as the blue, green and red components respectively, with simple contrast enhancement. This image is superior to some much more expensive enhancement techniques and allows unambiguous identification of areas of hydrothermal alteration larger than about 50m. The display includes a practical guide to the use of Landsat TM imagery for volcanic gold Exploration.

Jan 1, 1987

The design of mine ventilation systems for the BHP Steel Division Collieries is based on the acquisition of ventilation survey data for the establishment of a realistic computer net- work model. The branches which form the net- work for the computer models are calculated from a range of resistance factors incorporat- ing both a frictional and shock loss component. Since shock losses can account for up to 30 per cent of the total energy losses in mine airways the use of friction factors alone without accounting for shock losses will result in the choosing of an insufficiently performing fan. Published tables of friction factors have in- variably been taken from metalliferous or single entry studies and consequently are not reliable for Australia's mining conditions where multiple entries with regularly spaced cut-throughs are the normal practice. Typical resistance factors for roadways of rectangular cross-section 5.5 m x 2.0 m, with coal sides, have been found to vary from 0.11 Ns2/m8/km where no timber supports are used, to 0.98 Ns2/m8/km where double centre legging together with wooden chocks is used. In addition to the range of resistance factors due to varying support methods, the nature of use for a roadway is very significant because of the condition of repair and upkeep maintained.

Jan 1, 1983

By Hiddlestone D. C

Effective exploration, testing and analysis is essential for good process design and optimisation of coal preparation plants. Coal processing relies on the sizing and washability characteristics of the particular coal to define the most cost effective design to meet the market requirements. Flowsheet development and equipment selection is dependent on the natural quality characteristics of the coal, its physical properties and the value of the final product in its market. The methodology of process selection and the key elements in design are discussed. Coal is consumed in two general markets: ò steaming coal - both domestic and export, and ò metallurgical coal. This paper discusses the typical economic analysis required to evaluate the potential for, and cost benefit of, providing the flexibility to switch coals between markets. A case study illustrates the methodology of process selection in a typical high value metallurgical coal.

Jan 1, 1997

I am honoured and very pleased to have been given the opportunity this evening to say a few words of thanks not only on behalf of all the guests but especially for the delegates and accompanying persons attending the 13th Congress of the Council of Mining and Metallurgical Institutions. Firstly, I would like to congratulate Sir Hamilton Whyte,KCMG for his most interesting address. In his far ranging talk, when he showed knowledge of widely diverse subjects, I had a brief fear that he was going to be talking about the details of support methods in deep level mines, or how to avoid flotation problems in multi-metal mines. Although he did not go that far, he touched on subjects which have arisen this week - long term planning and secure supply of minerals at acceptable prices. The dire predictions of the Club of Rome have been debunked with a far more elastic supply of minerals having been proved. Combined with the importance of a falling birthrate in some parts of the world, this will lead to many changes in the future, when hopefully governments will take the long term view rather than look at the next budget or the next election. Maybe some of them are not too lazy to do this for all of us. However as a fellow Ukranian, I feel that he might have been called something different if he had been in Australia. Sir Hamilton, thank you for your talk. Once upon a time - and this is not a fairy story - there was a cobbler who had two sons; one very bright who became a professor of mathematics; the other, dim, who became a millionaire shoemaker. Asked for the secret of his success, the millionaire attributed it to a vital piece of economics which his father had imparted, "Be content with small margins on a large turnover." "So", said the millionaire, "I make my shoes for $2 a pair and sell them for $5. I am very happy with the three per cent profit."

Jan 1, 1986

This paper explores options worthy of consideration in the management of S02 produced from the gold roasting operations at Kalgoorlie. Some of the options have relevance to other sources of SO2 in the region, eminating from nickel smelting operations. The paper considers the following options: 1. Capture of SO2 within the roaster where sulphur-containing reaction products are mixed with the calcine. 2. Processes in which the sulphur-containing products are bled separately from the stack for further treatment or for dumping as a waste. These include: Seawater-based scrubbing of SO2; Sulphuric acid manufacture as a feedstock for fertiliser production or for leaching of bauxite; its use as Caro's acid: and the production of value-added sulphur-containing reagents eg liquid S02 and sulphonic acid.

Jan 1, 1992

By Hulton SJ, MacKenzie DH

The Broken Hill orebody within the leases of ZC Mines is still a major lead-silver-zinc resource after over 80 years of mining. It illustrates particular problems encountered in resource and reserve estimation in old mines. The six mined ore lenses are characterised by three features: ò complex external geometry, ò high internal grade variability, ò bimodal grade distribution. The high grade 3, 2 and 1 lenses and B lode have sharp external contacts but contain some low grade internal zones. By contrast A lode is of lower average grade and comprises an extensive but geometrically variable mineralised zone within which are numerous irregular bodies of high and medium grade ore. Geological factors are the main source of variability in reserve estimation, which historically has been conservative. For many years the geological resource tonnage has been maintained at a level sufficient to make up for extraction but at a gradually declining grade. Using a geological block cut off grade of 10% Pb + Zn the present in situ resource is 53.8 Mt grading 8% lead and 13% zinc. Using empirical cut factors a "recoverable reserve" is derived from this large geological tonnage. There is some doubt that the "recoverable reserve" is conservative enough to reflect mining reality. The most sensitive indicator of forthcoming change in total resource or insufficient drilling and development is given by changes in the tonnage and grade of possible ore from which the proved and probable categories are derived. Examples are given to show that where reserves are drill indicated, the delineation required for proved ore reserves must be enhanced to achieve final stope design. The move in recent years to greater emphasis on non entry mining and lower recovery of in situ material poses a dilemma for a mine which has practised 100% recovery for much of its past. The need for a realistic reserve assessment in current terms needs to be balanced against the fullest possible geological knowledge of the resource to cater for future technological developments.

Jan 1, 1987

By Armstrong M, Kleingeld W. J

Current low prices for many metals mean that deposits have to be mined at high cut-offs (relative to their mean grade), which means that only a small percentage of mining blocks are above cut-off. Worse, at such high cut-offs, the blocks above cut-off are usually not grouped into convenient clumps for mining; they tend to be split into small isolated patches that are difficult to reach and hence expensive to extract. Companies wishing to acquire mineral properties have to be able to work out quickly what percentage of blocks are above cut-off and what can effectively be mined given the mining method envisaged. Moreover they need this information within a relatively short-time. The work presented here relates to typical South African gold mines (ie tabular orebodies) but the long-term objective is to develop tools for quantifying the impact of reserve breakup at high cut-offs for a wide range of underground mines including those that are not tabular. The mining method and the sampling procedure determine whether ore blocks can effectively be located and extracted economically. This project studied the impact of these two factors on the recoverable reserves for Witwatersrand gold mines. In order to be repeatable, the tests were done on numerical models of the deposit obtained by geostatistical simulations. To ensure realism, the orebody model and the mining scenarios were based on a specific mine. The recoverable reserves (ore tonnage above cut-off, the corresponding metal quantity and the average grade) were calculated for a wide range of cut-offs for four mining scenarios, as well as for the base case of free selection: ò Scenario 1: Blocks are taken if their true grade is above cut-off and if they are accessible from a raiseline (no information effect, no marginal blocks). ò Scenario 2: In addition to the accessible pay blocks, adjoining marginal blocks are taken (no information effect, + marginal blocks). ò Scenario 3: Blocks are taken if their estimated grade is above cut-off and if they are accessible from a raiseline. Here the estimator is the average of the face samples (information effect, no marginal blocks): ò Scenario 4: Accessible pay blocks are taken if their estimated grade is above cut-off. Adjoining marginal blocksare also taken (information effect, + marginal blocks). ò Free selection: All blocks whose true grade is above cut-off are taken irrespective of their accessibility. The results can be presented in different ways, for example by plotting ore tonnage above cut-off versus cut-off grade, or metal tonnage above cut-off versus cut-off grade etc. As expected, this shows the hierarchy between the five scenarios from the free selection base case to scenario No 2 (true accumulations, pay +

Jan 1, 1995

By A G. Grice

Surface disposal of mining processing wastes is usually perceived as an undesirable consequence of meeting societyÆs needs for metals and minerals. Environmental disasters associated with the discharge or storage of such wastes, though infrequent, can have very damaging consequences for the environment and the industry. Reducing or eliminating the potential for such events may be achieved by placing some or all of these processing wastes back into the voids created by the mining operations. Processing operations may limit or enhance the opportunities for using tailings and other waste products as a backfill material. Backfilling is a truly multi-disciplinary process and requires the informed involvement of mining, metallurgical, engineering and environmental specialists. This paper describes the range of fill types currently being used in Australian mines, particularly those utilising processing wastes as constituents. It focuses on how processing operations can affect the suitability of these materials for the various types of fill, the resulting fill properties, fill performance and costs.

Jan 1, 2002

With more difficult economic conditions and increased competition, the Australian exploration industry is allocating increased resources to developing more effective and efficient exploration technologies. A significant number of new techniques have been developed, and Australian companies are now at the forefront of exploration technology worldwide. These should increase the chances of maintaining Australia's leading position in world mining over the long term.

Jan 1, 1987

By Myers I. A, Peters S. G, Bultitude R. J, Dowling K

Gold-quartz and antimony-gold-quartz veins in the Hodgkinson Province are hosted by subgreenschist to greenschist facies metasediments and show no spatial association with granitic rocks. They commonly parallel axial plane foliations or occur in brittle to brittle-ductile shear zones. Detailed mapping in the Hodgkinson goldfield indicates that vein systems are isolated in distinct structural and lithologic domains by post-mineralization faulting. Gold-quartz and antimony-gold-quartz veins have distinctive mesoscopic textures characteristic of the mesothermal vein environment. Some of the antimony-gold-quartz veins are located on domain boundaries which truncate the gold mineralization. In. some areas, tin and tungsten-tin mineralization which are spatially related to Late Palaeozoic granitoids appear to postdate the gold-quartz and antimony-gold-quartz mineralization.Oxygen and hydrogen isotopic studies of vein and alteration assemblages associated with these diverse ores provide constraints on fluid sources and have implications for the origin of mesothermal gold mineralization. The available isotopic data are consistent with a dominantly magmatic source for tin and tungsten-tin mineralization although there is evidence of a late-stage meteoric component in some tin-mineralizing systems. Although a distal magmatic contribution cannot be entirely discounted, the gold-quartz and antimony-gold-quartz veins were probably deposited from deeply

Jan 1, 1990