Search Documents

By M D. Melville, B C. T Macdonald, T D. W

The surface waters in regions with acid sulfate soils (ASS) can contain high concentrations of acidity and dissolved metals. These soils cause problems for agriculture, construction and development. The water can be neutralised through many techniques, however a technique that is low in maintenance and low in cost is most desirable. Due to the vast spread of ASS along AustraliaÆs coastline an expensive and high maintenance solution would not be cost-effective. In this study, a passive treatment system that has been used to neutralise acid rock drainage has been applied to treat ASS water. This system is commonly referred to as an oxic limestone drain (OLD) or an anoxic limestone drain (ALD) depending on the waters dissolved oxygen concentration. The system that has been developed for ASS has a similar closed system to the OLD or ALD, that traps the carbon dioxide which forms when limestone reacts with acidic water. It has been called a closed tank reactor (CTR) and is constructed by placing limestone into an airtight tank. A common problem that will occur when acidic water with a high concentration of dissolved metals reacts with limestone is the formation of metal oxy-hydroxide precipitates. These precipitates can coat or armour the limestone and reduce its reactivity. To minimise the accumulation of precipitates in the CTR, perforated subdrains have been installed. It is anticipated that high water pressure and flow through the subdrains will remove some precipitates. A sump has also been installed at the base of the tank to collect precipitates that settle under gravity. The CTR has been tested for 70 days at a sugar cane farm located at McLeods Creek, NSW. Within this time the sump and subdrains have been used to flush the system. An orange solution was produced during flushing and it is believed to contain iron and aluminium precipitates. The initial performance of the CTR raised pH by at least one unit. Almost all dissolved aluminium was removed and more than half the dissolved iron. The total titratable acidity ranged from 17 - 92 mg/L CaCO3 in the initial month of monitoring. After passing through the CTR the acidity was reduced to zero. The performance of the CTR during the last few days of monitoring decreased. This is believed to be due to a pulse of water with higher acidity and dissolved metal content that lasted a week. In this pulse, the acidity reached 307 mg/L CaCO3 and the total dissolved aluminium reached a maximum of 24 mg/L. Higher concentrations of dissolved metals may have been the cause for lower performance due to increased precipitation and coating on the limestone.

Jan 1, 2003

By M Clay, J Dunlop

Thermal and metallurgical coal mining in Queensland has resulted in mines which contain voids due to open cut mining. While there are several proposals for greenfield coalmines or expansions to existing operations, many existing open cut coalmines are reaching maturity and most will leave one or more residual voids in place. The rehabilitation of mine voids is challenging. Water held in voids will evaporate over time leaving solutes to concentrate. This is likely to lead to poor water quality with limited practical use. The most basic practices to rehabilitate voids have historically involved stabilising the high and low walls, bunding to provide flood protection, and preventing public access. Regulatory reforms for mine rehabilitation were introduced in Queensland as part of the Mineral and Energy Resources (Financial Provisioning) Act 2018, and aimed to strengthen progressive rehabilitation planning, limit risks to the environment and improve outcomes for local and regional communities. Under the reforms, the goal for rehabilitation of voids is to achieve a safe, stable, and non-polluting landform, which can sustain a post-mining land use (PMLU). The reforms also introduced a requirement to describe rehabilitation of mined land in Progressive Rehabilitation and Closure (PRC) plans, replacing the description of such plans in Environmental Authorities (EAs). The reforms are not retrospective and recognise historic approvals for voids, meaning established voids will remain in the landscape as non-use management areas (NUMAs). The objectives of this study were to outline historic void rehabilitation planning practices, describe water quality limitations of Queensland mine voids and identify possible opportunities for improved planning

Aug 2, 2023

By S Mitra, D O’Dea, N Barrett, T Honeyands, P Zulli

The steel industry continues to explore and demonstrate technologies that decrease its greenhouse gas emissions, especially in blast furnace ironmaking where alternate operating conditions will be required. As the furnace has been optimised over many years, it is approaching the minimum fuel rate possible with coke and Pulverised Coal Injection (PCI). Alternative operating conditions are therefore required to further decrease greenhouse gas emissions. Because of this, hydrogen has been proposed as a reducing agent in the blast furnace. Injection of hydrogen through the tuyeres was assessed using a comprehensive 2D blast furnace global model. The model was calibrated to a blast furnace operating with PCI as a base case and various approaches to hydrogen injection assessed, with a particular focus on displacing PCI. The maximum hydrogen injection rate of 19.5 kg H2 per tonne of hot metal was predicted, limited by decreases in the raceway adiabatic flame temperature and top gas temperature. Internal blast furnace conditions, such as gas composition and reduction degree were also predicted. Holistic analysis was performed to estimate the effectiveness of hydrogen injection on reduction of greenhouse gas emissions. Based on these results, the changes in blast furnace operation and emissions under hydrogen injection are discussed.

Nov 8, 2021

The performance of the Australian Mining Industry over the past 10 years using key indicators of production, revenue, aftertax return investment, together with key cost elements, market changes and ore reserves is briefly reviewed. The elements of competitiveness are discussed forthe industry and the effects of Government charges and policies relating to existing operations are outlined. There is a demonstrated need for improvements in competitiveness in direct and indirect costs and for improved access to resources for the mining industry to continue to grow and add to Australia's economic growth.

Jan 1, 1987

By N Madani, Y Abildin, E Topal

Mine planning is a crucial part of all mining industry projects, and nowadays, geometallurgical mapping through advanced computer technologies provides an opportunity to involve metallurgical responses of a deposit into 3D block model in order to optimise mine planning activities, especially for production forecasting. Including these metallurgical parameters apart from traditional geology and grade-based attributes into resource modelling leads to an extensive approximation for the economic maximisation of mine production due to better forecasting, planning and increasing certainty and the reliability of the resource model (Macfarlane and Williams, 2014). Commonly, geostatistical techniques and algorithms are used to produce models with the high resolution (Brissette et al. 2014; Deutsch et al. 2014; Tolosana-Delgado et al. 2015). The accuracy of the modelling procedure deeply depends on a reliable block model, produced by spatial analysis of corresponding variables that define the geological, metallurgical, mineralogical and chemical behaviour of the deposit. However, there are special cases, where the application of enhanced geostatistical methods is required, to solve the occurred difficulties between variables with multivariate complexities. For example, in oxide copper deposits, the soluble copper grade is a percentage of total copper grade and recoverable by heap leaching processes (Emery, 2012; Hosseini and Asghari, 2015). Hence, the joint spatial modelling of these variables has two difficulties.CITATION:Abildin, Y, Madani, N and Topal, E, 2018. Forecast the mineral processing destinations based on spatial interpolation of geometallurgical variables, in Proceedings Complex Orebodies Conference 2018, pp 2–5 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By M Grossi, G Baiden

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and onsite applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no dewatering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

Kumba Iron OreÆs Sishen Mine is one of the worldÆs largest iron ore mining operations situated in the Northern Cape, South Africa. It produces 29 million tonnes of iron ore products per annum using a dense medium separation (DMS) beneficiation process. Kumba is currently commissioning the Sishen Expansion Project (SEP) which will produce a further 13 Mtpa product through a jigging beneficiation process. The products from the Sishen Mine are highly sought after and consumed by domestic and various European and Asian customers. During beneficiation iron ore slimes are generated and discarded as waste material to the slimes dams. A study was initiated in 2005 to investigate processes to beneficiate these slimes to saleable products û prompted by the current high demand for iron ore products and the high grade in the Sishen slimes thickener underflow of approximately 54 per cent Fe. Initial laboratory scale test work indicated that a 66.5 per cent Fe iron ore concentrate could be produced from the Sishen slimes thickener underflow through a process of classification, two stage wet high intensity magnetic separation (WHIMS) and five stage flotation. This process, however, did not produce the desired results during pilot plant testing and numerous alternative process routes were investigated. The process that did achieve the desired product grade of 66.5 per cent Fe at economically feasible product yields consisted of two stage WHIMS using SLON magnetic separators. Results achieved indicate that the thickener underflow slimes can be upgraded from 54 per cent Fe to 66.5 per cent Fe at a product yield of ca. 40 per cent. Product yield could be increased through the further beneficiation of the SLON tails. The Sishen slimes thickener underflow production rate is ca. 3 Mtpa û resulting in a potential concentrate production of ca. 1.2 Mtpa. The slimes concentrate will be fed to a pelletising plant that will produce 66 per cent Fe pellets destined for domestic and or export markets.

Jan 1, 2008

By Grieveson P, Terry B. S

Carbothermic reduction of sulphide minerals for achieving a selective separation of metallic species from complex minerals has been discussed by considering the prevailing oxygen potential during the course of reaction. Construction of univariant plots for the reduction of sulphides with carbon monoxide gas or carbon and in the presence of either lime or anhydrous calcium sulphate is the key feature of this work. The theoretical calculations for univariants in the Cu-Fe-S-O system indicated a preferential separation of metallic copper and iron by imposing a chemical potential. This is evident from a logarithmic plot of sulphur dioxide partial pressure against reciprocal temperature. The results are compared with empirical data for the reduction equilibrium. The reduction behaviour of the constituent sulphides are also discussed together with the experimental results and theoretically predicted phase stability diagrams.

Jan 1, 1992

The Lihir deposit in Papua New Guinea (PNG) contains an estimated mineable reserve of 454t (14.6M oz) of gold in refractory sulphide ore. The Lihir Joint Venture has submitted a proposal to the PNG Government to develop an open pit mine and to install a process plant and associated infrastructure facilities on Lihir Island. The proposed process plant will employ whole-ore pressure oxidation technology, has a design capacity of 2.825Mt/a of ore containing 7.20 sulphide sulphur, and is expected to average 19.3t/a (620,000 oz/a) in gold production during its first 12 years of operation.An extensive program of process development testwork and feasibility engineering was completed to establish the process plant design for the Lihir Project. Summary results of this test-work as well as key design criteria, the process flowsheet, and major equipment selected for the commercial plant are presented and discussed.

Jan 1, 1994

By E Villaescusa, C Drover, I Onederra

Development face destress blasting is a construction technique in deep mining, which aims to prevent, reduce the frequency, or manipulate the timing of violent, stress-driven rock mass instability at the face. This paper presents a destress blasting design concept that was optimised for the specific rock mass conditions of a deep mine using the Hybrid Stress Blasting Model (HSBM) software. The design was then implemented in an area of the mine where stress-driven instability of the face regularly occurred during development. An adjacent tunnel was constructed in parallel without destressing, within the same rock mass conditions, as a control. The rock mass response to each excavation was quantitatively compared using high-resolution local seismic monitoring. Visual observations of the fractures created by destress blasting were also made. The analysis indicated that destressing reduced both seismicity and the rock mass stiffness ahead of the face. This was inferred from the spatial broadening of the development seismogenic zone and the typically significant reduction in the spatial density of seismic events. Seismic source mechanism analysis also indicated that destress blasting generated a much wider variety of failure modes than conventional blasting. Most seismic source mechanisms following destressing were associated with natural joint structures. A relatively small portion were consistent with newly created blast-induced fractures. The greater diversity of rock mass failure modes associated with destressing implied a lower potential for stain-energy accumulation within the rock mass at the face, and thus a lower risk of hazardous instability. Observations of visible rock fracturing indicated that the major principal stress influenced the damage intensity on natural geological structures within the destressed zone, and that numerical predictions of radial fracturing limits made by HSBM analysis were realistic representations of the real blasting performance.

Nov 29, 2022

By G C. Reed, J M. Murray

During more than 100 years continuous mining of the lead-zinc orebody at Broken Hill, an immense amount of geological data has been collected about shear zones related to the orebody. The challenge to current mine geologists is to synthesise and interpret these data sets in a way that is applicable to production demands. Precise knowledge of the locations of major shear zones is important not only for the determination of ground conditions but also to develop an understanding of ore remobilisation along these structures. Traditionally, geological information has been collected from drill core and back and wall mapping underground, and interpreted on sections that are approximately 20 m apart. The recent introduction of MaptekÆs Vulcan software has enabled the shear zones to be modelled in three dimensions. The new three-dimensional shear models have been combined with seismic data from the Southern Cross area. The seismic data is collected from a microseismic monitoring system installed in the Pasminco Southern Operations in August 1996 (Rauert and Tully, 1998). The addition of seismic information to the shear zone models has led to a greater degree of certainty about the shear zone locations and has provided information about shear zones in areas yet to be drilled.

Jan 1, 2000

By P Mikula, B Darlington, J Graham, P Young

In underground mines experiencing dynamic events, there is an ever-present challenge to design and maintain a capable ground support system. One key component of ground support systems is surface support, which serves the essential roles of retaining failed rock and transferring forces generated by surface displacement to rock bolts or other support elements. Observations underground show that in many instances, standard mesh panels alone do not provide sufficient dynamic support to retain substantial bulking failures imposing displacement onto mesh, and in such cases Mesh straps and W-straps may be employed. Determining the performance of surface support elements proves to be difficult, with a multitude of variables at play in the underground environment. Quite comprehensive work has been completed on laboratory testing of surface support systems; however, very little work has been conducted on in situ dynamic testing of Mesh straps and W-straps. In 2019 in Western Area’s Flying Fox Mine, in situ dynamic testing was conducted on a series of Mesh straps and W-straps using Sandvik’s in situ Dynamic Test Rig (DTR). The testing regime applied impact energies from 5.1 to 15.3 kJ to Mesh straps and W-straps. The performance of the straps that did not fail was a maximum absorbed energy of 9.3 kJ and 14.2 kJ for the Mesh straps and W-straps respectively. The testing successfully demonstrated the ability of Sandvik’s DTR to test not only rock bolts, but also surface support elements, creating new testing and research possibilities. The testing also provided important design guidance data that is not practicable to obtain using laboratory dynamic testing facilities.

Nov 29, 2022

By Ralph AM, Deakin JJ

A quantitative knowledge of underground mine ventilation requirements and conditions has become increasingly important, both to meet statutory requirements and to ensure high levels of safety and productivity within mines. The ACIRL Mine Ventilation System MINVENT was designed to provide a flexible means of analysing the behaviour of an underground mine ventilation system under a variety of conditions. It is not sufficient to rely solely on the analytical tools such as ventilation network analysis computer programs - these must be supported by the expertise necessary to conduct an accurate underground ventilation survey as well as experience of typical conditions to be expected in the evaluation of proposed extensions to a new or existing mine. When planning a new mine, the ventilation engineer can use the program to draw on a set of typical ventilation parameters, seam and proposed mining methods. These have been assembled as a result of numerous ventilation surveys conducted by ACIRL in New South Wales and Queensland.

Jan 1, 1983

By Coxhead B. A, Brandt B. A

The geological exploration and evaluation of coal reserves involves the appraisal of very large amounts of data. Computers afford an ideal means of handling and manipulating the data, thereby avoiding the laborious and expensive method of manually compiling the logs in full descriptive language. The Minad system of computer storage and retrieval of geological and analytical data is particularly suited to the description of cores and cuttings from exploration drill-holes. The encoded data is arranged in a 120-column computer output sheet format; descriptive geological information in a 54-column geolog and analytical information in a 64-column assaylog. The acquired data is quantitative, uniform and relatively complete and can be selectively retrieved for processing by a wide range of specialized computer programs developed for the coal mining industry. Visual retrieval of data for manual processing is facilitated by the use of simple codes and logical word abbreviations.

Jan 1, 1977

By H Kusumi, A Nishio, K D. Halim, Y Yun

In Japan, evaluation of rock mass is crucial in mountain tunnels that are constructed using the NATM (New Austrian Tunneling Method) to determine the support pattern that in turns determine the final support structure of the tunnel. The current evaluation method is highly dependent on the observations of on-site expert engineers that grades the rock mass in four levels across nine criteria: A. Condition of tunnel face. B. Condition of excavated surface. C. Compressive rock strength. D. Weathering. E. Spacing of discontinuity. F. Condition of discontinuity. G. Orientation of discontinuity. H. Spring water. I. Water degradation. However, in recent years, the number of said experts are decreasing rapidly due to labour shortage caused mainly by an aging population and declining birth rates. This is one of the biggest challenges that the construction sector currently faces, and this may affect the efficiency of tunnel construction projects in the future. Thus, this study proposes the implementation of a deep learning tool called the convolutional neural network (CNN) to quantitatively evaluate rock fractures on tunnel face. In addition, Gradient-weighted Class Activation Mapping (Grad-CAM) is applied to visualise CNN, as well as verify the applicability of CNN to the evaluation of rock fractures. In other words, by creating heat maps of tunnel face images, CNN is utilised to evaluate rock mass in categories that are associated with discontinuities. The CNN model is most accurate when six convolution layers, four pooling layers, and three dense layers are used. This yields an accuracy of 75.0~88.0 per cent. Thus, the CNN model is verified to be feasible method to evaluate rock fractures.

Nov 29, 2022

By D J. Gray

The 4 km long Huguenot Toll Tunnel in the Western Cape region of South Africa celebrated its tenth anniversary on 18 March 1998. At present a single (South) bore with bi-directional traffic flow is operational. The North bore was originally excavated but not lined and equipped.The tunnel is fitted with a semi-transverse ventilation system comprising 45/350 kW two speed fresh-air and 1 MW exhaust air fans at each of the portals. These provide ventilation through fresh and exhaust air ducts above the ceiling separated by movable partition doors. Secondary air ducts deliver air at low level. The fan control depends on the levels of CO pollution or visibility measured at six positions along the tunnel.The system performed well during initial tests and under conditions of low traffic volumes. As traffic volumes increased, and user complaints of bad air in the tunnel were received on several occasions, we realised that we had a problem. Tests confirmed that natural airflow within the tunnel induced by prevailing meteorological conditions outside the portals affected the performance of the ventilation system causing a plug of bad air to be trapped at varying positions along the operating tunnel.The control systems in the tunnel are presently being upgraded as described by Gray, Rieckert and Bullock (1998). As part of the retrofit we are implementing a new control strategy for the ventilation system which takes into account the external weather conditions. This paper discusses the 24 month long meteorological data gathering exercise, which is on-going, and explores the philosophies planned for controlling the ventilation system. The correlation between winds external to the tunnel and induced airflow inside the tunnel are examined. The effects of the weather induced airflow on the existing ventilation system are considered and proposals given for taking these effects into account in the new control strategy. These include the implementation of an expert system to predict ambient airflow from prevailing weather conditions, and the use of airflow measurements taken in the uncompleted North bore as a cross-check.The paper highlights the need to take cognisance of external weather conditions when designing tunnel ventilation systems.

Jan 1, 1999

Early in 1950 a new laboratory was set up to deal with problems in mineragraphy, petrology and metallography. This paper describes the equipment, the organisation and association of the laboratory with the various departments of the company, the work that has been done and future plans.At Mount Isa it was soon realised that the microscope would play a most important role in mineral dressing problems and aiding geological research.As early as 1928, R. J. Colony submitted a petrographic report on Black Star ore for Consolidated Limited; much later, in 1934-5 Dr. Grondijs published for Mount Isa Mines Limited a preliminary study of the Mount Isa orebody, followed by a mineragraphicinvestigation of mill products, and in 1937 a Study of Mount Isa Ores by H. GrondIjs and C. Schouten appeared in Economic Geology, for June-July. Other papers dealing with the petrology and mineragraphy of Mount Isa ores are appended at the end of the paper.The mill research metallurgical staff has endeavoured to incorporate mineragraphy in solving milling problems and determining the effectiveness of laboratory as well as examining minerals sent in by the geological department.For many years the amount of equipment available was limited and much of it was locally made or improvised. An improvised briquetting machine, and grinding and polishing lap gave moderate results in conjunction with an old, but serviceable, Leitz microscope. However, for more detailed and accurate work not possible with improvised equipment, many mineragraphic problems were sent to specialist in.

Jan 1, 1953

Since the days of Adam Smith and Milton Friedman the discussion of corporate citizenship and sustainability has been flooded with multiple contradictions, with proponents of sustainability saying that it is a crucial cog in the business strategy, while those against, maintain that æthe business of business is businessÆ and therefore sustainability issues are just add-ons. Sustainability arises from a deeply held vision by corporate leaders that businesses can and should play a role beyond just making money. Businesses should embrace the understanding that everything that a company does has an impact both internally and externally (communities, employees and customers), and the natural environment. This paper highlights the approach that led to a view that there is a contradiction between profitability, sustainability and community development, and we provide a further argument to the contrary. This argument is based on a comprehensive literature review of over three decades by various scholars linking corporate social performance and corporate financial performance. Driefontein Gold MineÆs approach is that of linking the community development, natural environmental and employee well-being initiatives and projects to the mineÆs business strategy. The paper further highlights the coordination and implementation mechanism of sustainability at the mine where the accountability lies with the head of the mine operations. A two pronged approach is employed where there is an internal dialogue on sustainability between the various departments coordinated by the sustainable development department and an external tri-sector partnership with local government, interested and affected parties and the mine. These approaches are closely linked to the contributions towards the mineÆs financial bottom line.

Jan 1, 2009

The ores described in this paper are from the two principal orebodies at Wiseman's Creek, a small village about 22 miles south-east of Bathurst in central-western New South Wales.The first official reference to mining at Wiseman's Creek is in "Mineral Statistics of New South Wales" of 1875, which reported that the Wiseman's Creek Copper Mining Company had proved a lode-later known as "North Wiseman's"-to a depth of 120 ft., where it was found to be 20 ft. wide. By 1876 the erection of a mill and smelting works had commenced, and the sulphide ore found to contain copper lead, zinc, silver and gold. Some oxidised ore was also being worked. Operations were, however, generally unsuccessful, and sporadic work up until 1907 produced only about 5,000 tons of ore. The other more important orebody of the locality-the Phoenix-was not opened until about 1895. By 1908, as reported by J. E. Carne, the shaft had been sunk 340 ft., with the extraction of both oxidised and primary ore. At the time of the slump in copper, pric'es in 1907 approximately 3,000 tons of, ore had been produced.Several smaller orebodies were discovered and worked during the same period as the North Wiseman's and Phoenix, but their output was more or less insignficant. THE OREBODIES AND THEIR GEOLOGICAL SETTINGIt is now impossible to examine the orebodies underground, but they appear to have formed a series of flat lenses, whose major axes were parallel to ,the foliation of the enclosing quartz-chlorite-muscovite schists. The largest ,of these lenses was worked as the North Wiseman's orebody, which was reported by Carne to vary in width from 1 ft. to 20 ft., and which probably extended discontinuously over a strike length of about 1,000 ft. The Phoenix orebody is stated to have varied from 1 ft. 6 in. to 3 ft. in width...

Jan 1, 1955

By Johns AS

Comissioning of a new residue disposal tcluding upgraded classification for none backfill preparation, new variable speed pumps and a new residue dam took place in 1¦76. The system is described.

Jan 1, 1978