Search Documents

By J Ledgerwood

Namakwa Sands is a mineral processing company based on the West Coast of South Africa and is solely owned by Exxaro Resources Limited. Mineral ore is mined and processed, concentrated and both chemical and mechanically upgraded before being sent for electrostatic and magnetic separation units. The final high value mineral products report as Zircon, Rutile and Ilmenite.The recovery of non-magnetic material is largely dependent upon a number of factors, including but not limited to dew point, ambient temperature, feed rate, mineral size distribution, specific gravity and mineral content in head feed. One important limiting factor to recovery in typical dry mill operations is the particle size distribution of the feed. Variance in the particle size has catastrophic consequences for recovery. This is the reason for this study. Until recently large variances in non-magnetic production were viewed to be a function of machine operation. This view was later rejected with the feed size distribution determined as the major driver of low recoveries, for Namakwa Sands orebody 50 per cent variance in particle size distribution can be noticed within one day. This is because of the successive mining blending techniques employed.The predicament is that the two modes were so closely placed together that recovery of a single mode is almost impossible without the consequence of greatly reducing recovery. The second mode was found at 125 µm while the first was at 90 µm. Interestingly, for the mentioned feed type a cumulative size distribution of a unimodal feed type is almost exactly the same as for a bimodal size distribution. Thus a plot of cumulative size distribution will show no difference due to the modes being so close together. This is the reason why this phenomenon was not noticed before.The study also found that, using an high tension roll (HTR) or rare earth roll, a fine stream with a single mode at 90 µm versus a coarse stream with a single mode at 150 µm would yield completely different results interms of yields. Larger conductive particles are thrown from the roll while small particles loose charge faster (entrainment). Results in terms of the bimodal size distribution show that even though 25 per cent of the feed type is greater than 150 µm the yields followed a similar pattern to that of the coarse particles rather than that of the majority (75 per cent) fine particles. This confirms what was published by M Ziemski and P N Holtham in 2005 on charge decay rates; they mentioned that particle bed effects played a major role in recovery.

Oct 5, 2011

By Nemick JA

Recent advances in computer simulation together with field measurements of caving and microseismic activity about longwall panels, has allowed a much better understanding of the caving process and the variability due to geology. The joint research between SCT Operations and CSIRO Division of Exploration and Mining has initiated new methods of computational modelling predicting various caving patterns and strata failure far ahead of the longwall face. This work was validated by field measurements of caving and microseismic activity at the longwall face.The rock fracture distribution and the caving characteristics of a range of strata sections have been simulated by computer methods. Validation studies of the method were addressed together with case studies. The interaction of caving with support convergence and face control is presented. The method allows the simulation of longwall support behaviour under various geological conditions. The system also allows a prediction of the monitoring data, which is best suited to give an early warning of weighting events or signal various key caving characteristics.

Jan 1, 1998

By K Biegaj, S C. Dominy

A high-nugget effect and presence of coarse gold characterises many styles of gold mineralisation. The effective sampling of these deposits is often difficult because of the relatively low concentrations involved and erratic nature of the gold or other minerals. Geometric and/or metallurgical complexities often compound this effect. Underground development, in-fill drilling and bulk sampling/trial mining are generally required to delineate Ore Reserves. Similarly expensive definition strategies often apply to surface mining in complex orebodies of gold and other minerals, including precious stones. Development, particularly winzing is a historical technique that was used to gather geological, grade and metallurgical data during underground and near-surface exploration. It permits access to the mineralised structure below the surface datum to determine viability. Winzing has always been considered an arduous and dangerous task. Modern winzing technology has led to the development of the Mobile Supersucker – essentially a giant vacuum cleaner with underground and surface capabilities. By the elimination of shovel-loaded blasted winze material into a kibble and hoisting, this system permits safe and highly efficient winzing activities, and allows the collection of bulk samples for grade and metallurgical evaluation, as well as access to the mineralisation for geological and geotechnical mapping. Bulk samples from horizontal development have long been collected to help define mineable grade via pilot processing. However, when defining blocks below current development, there has been over-reliance on ineffective ‘small sample’ drill data. The Mobile Supersucker permits the development of winzes and off-winze sub-levels. These provide critical information to a mine technical team when trying to justify capital to go deeper or commence or deepen an existing open pit. CITATION: Biegaj, K and Dominy, S C, 2018. Lowering risk in complex mineralisation: application of mobile supersucker development, in Proceedings Complex Orebodies Conference 2018, pp 113–115 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By Lock PR

The Silver Swan nickel mine is located at the Black Swan Nickel Project, 53 kin north east of Kalgoorlie, Western Australia. The Silver Swan orebody is a massive sulphide nickel deposit dipping 70¦ east with an average in situ grade of 14 per cent. Mining of the massive orebody is by Mechanised Ramp Cut and Fill (MRCF). A mining recovery of 98 per cent and minimising dilution are primary goals in extracting the high-grade ore. Placing a distinguishable marker bed (working platform) on rock fill was identified as a key method to achieving these goals. Gravel from a pit located onsite was considered the most suitable material for the marker beds. Research undertaken to design the marker beds using the gravel revealed conventional methods used in mining would not suffice, but that road stabilisation methods could be a viable alternative. Trials used a road recycler to mix cement and gravel in situ and several test beds were constructed on the surface to determine the final design. The trials attempted to replicate a marker bed's life cycle of construction and placement and mucking of ore from the marker bed.

Jan 1, 1998

By MacDonald AJ, Raffield MP

The South Deep massive orebody consists of 20 to 30 in of payable conglomerates ranging in dip from 11¦ to 20¦ and at depths of between 2400 in and 34(10 in. The mine design process selected a mining method with a proven record of application that could be adapted to overcome the inherent difficulties associated with the depth, thickness and structural influences of the South Deep orebody. A modified cut and fill mining method provides a concentrated and highly flexible method of extraction. An integrated destressing cut will enable the modification of the stress environment such that it is suitable for massive mining operations. The choice of backfill type and stoping width in the destressing cut ultimately determines the characteristics of the stress modification and, as such, is critical to the success of the cut and fill operation. This paper discusses the decision process undertaken to determine the optimum backfill type and stoping width combination in terms of, conditions in the destressing cut faces and in the massive mining environment. Numerical modelling has been extensively used to analyse arious scenarios to aid in the decision process.

Jan 1, 1998

By Nikaido M, Kanda Y

A rotary type separator has been developed which separates particles on the basis of their shape. This separator was applied to a particle size range of about 50 - 120 ¦m, and to our present knowledge may be the smallest size range ever to be separated. A theory of the separation is given based on the difference of an adhesive force of the particles: the adhesive force between spherical particles and plate is more powerful than that of irregular shaped particles for the same particle size. These facts have been ascertained by the measurement of an adhesive force by a centrifugal method. US and Japanese patents have been obtained on this separator, which consists of a borosilicate glass cylinder of 150 mm outside diameter, 120 mm in width, and an AC electromagnet. The samples used in this study were mixtures of spherical glass particles and non-spherical shaped glass particles. The results are summarised as follows. In the case of mixtures of spherical particles and irregular shaped particles in the weight ratio of 1:1, the spherical content of the spherical product became 70 per cent - 75 per cent, and in the case of 3:1, the content became 87 per cent - 90 per cent, as the result of one separating operation. However, for a mixture of somewhat rounded particles and irregular shaped particles of weight ratio 1:1, the rounded content varied between 58 per cent - 73 per cent. The feed rate of the particles mixtures was about 0.3 g/min. Newton's Efficiency was 20 per cent - 60 per cent. The separator may find application in shape separation of ceramic powder, metal powder or industrial diamond powder.

Jan 1, 1993

By Ryan A, Dennis R, Dekker D, Ellis W, Sowerby B

An automated facility for non-destructive elemental analysis of mine samples has been developed and tested at Mount Isa in association with the CSIRO. The analysis is based on the prompt and delayed measurement of gamma radiation emitted by the sample during and after separate fast and thermal neutron irradiation. No sub-sampling or sample preparation is required and the analyser is operated by one person that would otherwise be splitting drill core in preparation for conventional analysis. The analyser has been calibrated to measure the following (precision in parenthesis): Ag (14 ppm), Pb (0.5 wt%), Zn (0.5 wt%), Cu (0.04 wt%), Fe (0.7 wt%), S (1.1 wt%), SiO2 (0.8 wt%), A1203 (0.07 wt%), Mn (0.05 wt%), specific gravity (0.02 g cmt). Crushed or whole drill core samples that range in size between 0.5 m and 1.8 m of equivalent BQ size drill core can be analysed at a rate of six samples per hour. If required, drill core samples can be re-packed in their original configuration for storage following analysis. Standard samples are measured every day to ensure operational stability. The analyser is controlled by a personal computer which prints the results and stores them along with the raw data on the computer hard disk. This paper reports the performance of the analyser during 1992 for routine analysis of drill core from the lead ore bodies of both Mount Isa and Hilton mines.

Jan 1, 1993

By Medhurst TP, Trueman R, Hutchinson IN

A breaker line support (BLS) monitoring system, BLSmon, has been designed and constructed by the CSIRO and installed and commissioned at Laleham No.] Colliery, Queensland. This system was designed to record hydraulic leg pressure and canopy position measurements and relay these, in real time, to the surface. The system has shown itself to be capable of operating on the BLSs without any adverse affect on production. Analysis of the results of the monitoring exercise has shown that rate of change of leg pressures on the BLSs could be used as an aid in the prediction of adverse mining conditions. Under favourable mining conditions the supports were observed to initially unload from the set pressure, this unloading reduced with time and by the end of a typical lift cycle had either ceased or reversed slightly. This behaviour was considered to be due to one of four possible causes, these being; the compaction of floor debris, and/or compaction of the floor, and/or crushing of the roof and /or support creep. The actual cause can only be determined through detailed monitoring of both roof and support convergence. However observational data would suggest that compaction of debris and softened floor material beneath the supports was the most likely cause. The few positive loading rates recorded under these conditions were of short duration and occurred towards the end of individual lifts. Where mining conditions were unfavourable the negative rates of change of pressure, unloading of the support, were reduced throughout a lift, in both duration and magnitude, when compared with favourable mining conditions. Over the same period the positive rates of change were observed to be greater. The rate of change of loading and convergence can be utilised to identify the onset of instability in the lift area. However, before this facility can be utilised by the mine for the reliable prediction of instability more monitored data and sophisticated processing techniques are required.

Jan 1, 1992

By R Grogan

Nautilus Minerals (Nautilus) is a sea floor resource exploration and development company focused on developing the Solwara 1 Project, a copper-gold sea floor massive sulfide deposit in the territorial waters of Papua New Guinea, for which it holds a mining lease and associated environment permit.During the environmental impact assessment and project development phase, Nautilus completed a number of hydrodynamic modelling exercises in order to predict the nature, volume and extent of the plumes likely to be generated by the sea floor mining tools and return water discharge at the sea floor.The modelling was conducted using the suspended sediment fate model (SSFATE), developed by the United States Army Corps of Engineers and RPS APASA engineering consultants. The SSFATE model was originally developed in order to predict and manage dredging plumes, and has since been adapted for deep ocean sea floor mining. The model uses a Lagrangian approach to remove the limitations of grid resolution, and simulates far-field effects of sedimentation plumes by assuming that the average transport and turbulence associated with currents are dominant over the initial turbulence at the release point. The random walk procedure utilised in the model tracks particle size classes as they disperse and settle, and also takes into consideration any re-suspension that may occur following settlement (RPS APASA, 2014).CITATION:Grogan, R, 2016. Predicting, assessing and managing sediment plumes generated by sea floor mining, in Proceedings Life-of-Mine 2016 Conference, pp 124–127 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By V Rimal, d M. Tangstad

Multiphase slags form the basis of the reduction pathway for manganese ferroalloy production. The present work aims to understand the flow of slag through the coke bed based on experimentation in controlled conditions. Synthetic slags of different basicities were evaluated for their phase composition, viscosity, and flow. The two-phase slag will have two zones: a liquid slag zone and a multiphase zone. The multiphase zone will consist mostly of a solid phase with some liquid slag between the solid particles. The multiphase part will hence have a high viscosity. The liquid zone will flow into the coke bed while the multiphase area will stay. With increasing reduction, the multiphase area will decrease in size until the solid phase is gone and the whole slag will flow into the coke bed. The effective viscosity of slag will decrease with the lowering of the solid oxide phase. The results from flow experiments confirmed that the segregation of phases occurs when slag flows through the coke bed. It is observed that the flow is dependent both on the size of the void and the viscosity of slag.

Aug 21, 2024

By P G. Greenhill

The Wonawinta silver project near Cobar in NSW is under development by Cobar Consolidated Resources Limited (CCR). RMDSTEM Limited is part of the owner’s team for feasibility, design, engineering, construction and commissioning.With a 51Moz resource CCR is one of the largest pure silver players in Australia. A probable reserve of 14.3Moz has been defined for a mine life of approximately five years. The silver mineralization is contained in host rock composed of clays and oxidized limestone. The ore also contains on average 1.3% lead as cerussite, and other minerals. A simple circuit consisting of slurrying of the ore, gravity treatment of the coarse fraction to recover lead, silver extraction using CIL, elution and the Merrill Crowe silver recovery process, has been developed.The “value engineering” approach to this development pioneered over the past decade by RMDSTEM has meant that RMDSTEM has delivered the bankable feasibility study at a cost of $0.07 per resource ounce. It is highly cost effective making efficient use of shareholders funds as well as being very time efficient. This paper describes the application of the value engineering approach to the development of the Wonawinta project.

Aug 8, 2011

By J E. Everett

Maximising ore tonnage at a selected target grade requires that appropriate ore identification criteria be established. Iron ore mining block models may consist of many millions of estimated blocks, each block corresponding to the selective mining unit (SMU), with grade interpolated from drill hole data. Each block can be considered as a potential ore candidate. Analysis of such a huge database can require large computational resources, especially for sensitivity analysis requiring multiple computations. However, an alternative streamlined approach is possible, where the data are compressed to an appropriately smaller and representative subset. The consequent data reduction not only makes it feasible to consider the simultaneous analysis of multiple pits but also considerably speeds up computation, enabling sensitivity analysis of the potential ore tonnage as a function of the required grade. Ore identification criteria can be successfully established using appropriately chosen reduced data comprising less than one per cent of the blocks. The ore identified is virtually indistinguishable in tonnage and grade from the ore that would be selected using the entire block model.Two methods of data reduction are tested: sampling (using a proportion of unaltered blocks) and binning (consolidating groups of blocks to a single average grade). The source blocks are first sorted (such as by location, analyte grade, principal component score, random order or value) before sampling or binning. In this study, the sorting options considered were by location and Fe grade. The effectiveness of each method was evaluated using the block model subsets to select the maximum tonnage of ore at a specified target grade. Block model data from an anonymous Pilbara iron ore project with about one million blocks averaging 1.132 kt were used. The blocks are from multiple resource models, to be blended to a single product. Sampling is shown to be superior to binning because sampling preserves the full variability while binning, although matching the mean block grades reduces their variability.It was found that the appropriately sampled data sets (sorted by location) gave results virtually identical to the results for the full data set, even when the samples comprised less than one per cent of the original blocks. The reduction in computer time to identify maximum tonnage at a specified grade was approximately proportional to the sample percentage. The increase in computation speed greatly facilitated sensitivity analysis. A sampled data set of one-eighth the total block model was used to investigate the effects of changing each of the component grades around the original grade specification. The results of this sensitivity analysis are discussed, and illustrate the potential benefit of carrying out sensitivity analysis in determining feasible and marketable product grades.CITATION:Everett, J E, 2015. Block model data reduction and sensitivity analysis, in Proceedings Iron Ore 2015, pp 263–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By P Yß±ez, G Ferguson

The El Teniente mine produces more than 340 000 tonnes of fine copper per year from an industrial complex of underground mine, concentrator and smelter. Mass caving methods are employed to deliver approximately 95 000 tpd of ore to the mill, from a number of sectors underground, each sector being in effect a large-scale mine in its own right. This mining activity has faced challenges over the course of the last century such as:the capacity of the underground mine has been expanded to maintain and increase output of fine copper; the increasing size of the ore fragmentation forced to change the mining method to achieve the high productivity and profitability required in the business; and to modify the mining methods to continue mining at depth with safety. Fundamental activities in these mining methods, for the successful initiation of caving and subsequent draw, are:undercutting the base of the block or panel by blasting; and excavating of drawbells. The undercutting design evolves mainly on the height of the blasting to manage the change on ore fragmentation. The methodology move away from incorporating massive areas, typical of the block caving method, to a continuos blasting, typical of the panel caving method. Drawbell design changes on geometry, dimensions and sequence of excavation to deal with a corse ore fragmentation and the resolution of mining difficulties in the form of major rock bursts and collapses of production facilities. This paper focuses upon the evolution of the undercutting and drawbell design used at El Teniente mine and techniques under consideration to deal with future caving operations to provide the bulk of the daily production for the foreseeable future.

Jan 1, 2000

By Gibson G, Jaques L

The Broken Hill Exploration Initiative (BHEI) is a collaborative venture between the Australian Geological Survey Organisation (AGSO), Mines and Energy South Australia (MESA) and the New South Wales Department of Mineral Resources (NSWDMR) to provide a new generation of geoscientific information to promote and enhance the exploration for, and discovery of, new deposits in the Broken Hill region. The area under investigation (Figure 1) exceeds 150 000 square kilometres on either side of the NSW-SA border and is centred on the city of Broken Hill. N.T. I I OL n. WA 8A I Maw. AC,7 !ii oFCU vlc~ ~T. Fia I - Nlap showing the 150 000 square kilometre regwa,. i.i lcr investigation by the Broken HiII Exploration Initiauvr highlighted on the map of Australia. A major impediment to the exploration for, and to the understanding of, the genesis of the world-class Broken Hill Pb-Ag-Zn deposit is the structural and metamorphic complexit\ of the region. Important objectives of the BHEI are therefore: I. the definition of the three-dimensional structure of the province, 2. the deformation history, and 3. the stratigraphic and age relationships of the rock units. Early discussions between the BHEI partners and industry scientists revealed that new geophysical surveys would be a key requirement to help advance the understanding of the province, especially a contiguous high resolution airborne geophysical dataset covering both outcrop and areas of shallow surficial cover. The purpose of this paper is to draw attention to the new high resolution airborne geophysical data and to discuss their interpretation and potential for enhancing the knowledge of the Willyama Supergroup geology.

Jan 1, 1997

By I M. Platten, Y Xie

Sampling protocols that are designed to suit the mineralisation style will result in a reduction of the nugget effect and hence resource risk. The a priori need for all sampling programs is the effective characterisation of the mineralisation type(s) to support optimisation. This requires a program of sampling for sampling followed by holistic characterisation. At each end of the coarse-gold to fine-gold spectrum, the samplability of a deposit ranges from relatively simple for fine-grained disseminated gold particles, through to extremely difficult for coarse nuggety mineralisation. Many deposits contain a proportion of both particle size types. The proportion and size of coarse gold particles has a direct impact on the effectiveness of sampling, where coarser particles will require larger samples and more specialised protocols. The nature of mineralisation geology/mineralogy and associated gold particle sizing can only be determined by sampling to facilitate optimised protocols. Mineralogical studies, focusing on particle size, particle clustering and distribution in host minerals, are required as part of wider paragenetic and metallurgical investigations. This paper discusses the role of mineralogical studies in the characterisation of gold ores for sampling optimisation through a series of case studies.

Jan 1, 2008

Gold was discovered at Waihi in 1878. In 1987 the modern Martha Mine opened in the middle of the town of Waihi. Newmont Waihi Gold as the current licence holder has been operating the mine since 2000. The current open pit was scheduled to stop production in mid 2006. An underground mine is currently being developed to the east of the town.   In 2001 serious subsidence issues from historical underground mine workings outside the mining licence and the forecast closure of the open pit acted as a catalyst for the development of new communication initiatives.   In this context Newmont Waihi Gold and the Hauraki District Council initiated a community consultation process with the people of Waihi. The Waihi Community Consultation Committee (WCCC) was established in May 2003. After an initial brief to act as a forum for community participation in closure and rehabilitation of the Martha Mine, the group quickly took on a much more proactive role working towards the long-term social, environmental, cultural, economic and spiritual sustainability of Waihi.   In the course of over three years of meetings all groups represented on the committee have presented their views, developed ideas and established an organisational structure to bring those ideas to fruition. The challenge now is to work together to consolidate likely options, seek sources of funding, produce business proposals and implement the plan for the future of Waihi.   This paper backgrounds the experience to date and describes the outcomes of the process. For more detail on process considerations this paper should be read in conjunction with Part C by process facilitators, T Clark and S Stewart. For more detail on progress towards the groupÆs goals and future possibilities, this paper should be read in conjunction with Part B by Vision Waihi Trust CEO, E Morrow.

Jan 1, 2006

ABSTRACT' Mainland Papua New Guinea is formed of a microcontinental / island arc system (?Eocene - latest Oligocene Sepic arc) which in Middle to Late Miocene times was obducted over the northward- moving Australian plate. The sedimentary and volcanic units of this system form part of the Wogamush Group (Aure beds, Mena beds, Omaura Formation, Movi beds, Wogamush beds, Wogamush Formation. Nansananka Conglomerate and other correlates in- eluding cale-alkaline volcanics and carbonate beds). This Sepic event was followed in Pliocene-Present times by the obduction of the Finisterre-Adelbert-Oenake fore-arc or possibly oceanic plateau. Obduction of the Sepic arc produced crustal thickening

Jan 1, 1997

By S Phinn, V Glenn, P McKenna, P D. Erskine, D Doley

The key goals for mine site rehabilitation require mine managers to demonstrate that rehabilitation is safe, stable, self-sustainable and non-polluting. Within this context, it is reasonable for stakeholders to expect that mine site rehabilitation is resilient to disturbance impacts such as fire and drought. However, mine managers actively avoid fire on rehabilitation; and as a result have limited understanding of fire behaviour on revegetated landforms, the long term implications for site stability and the potential risk to site relinquishment. An experimental fire that was conducted at the Curragh Mine site in May 2015, burnt 117 ha of 19- to 21-year old mine site rehabilitation, mimicking wildfire conditions and creating a mosaic of fire impacts across the landform. Using a combination of ground surveys and remote sensing assessments, we demonstrate that over a two year period, ecological metrics such as species richness, woody density and understorey biomass all recover to pre-fire levels for both grassland and open woodland areas. This is supported by WorldView-3 satellite imagery and the remote sensing assessment using the differenced Normalised Differenced Vegetation Index (dNDVI) which shows high regrowth within the burn area in 12- and 24-month image captures. The results suggest that within the recorded conditions, this site is resilient to fire impacts, and has the capacity to recover to pre-fire levels within the first two years following the fire.CITATION:McKenna, P, Erskine, P D, Phinn, S, Glenn, V and Doley, D, 2018. Measuring the recovery of coal mine rehabilitation following fire in Queensland using remote sensing and ground surveys, in Proceedings Life-of-Mine 2018, pp 141–146 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By A Kite

Frontline leaders play a critical role in the safe and productive operations of Australia’s mining, resources and heavy industries. These leaders set the workplace culture, especially during night shifts and weekends, by providing team direction and encouragement, providing access to resources, fulfilling statutory requirements, enacting and reinforcing risk management systems, setting the standards on shift and acting as the primary conduit of communications between senior leaders and team members.

May 5, 2022

By J Zhou

This paper discusses the implementation of a mixed integer linear programming model for a coal preparation plant. The plant considered consists of primary and secondary heavy media cyclones, hydrocyclones for intermediate fines and froth flotation for the very fine material. The model is designed to optimise the plant settings and product flows to maximise revenues for a given specification for two product outputs. The model can deal with bonus/penalty aspects of the product pricing for products that exceed or fail to meet specification. We report on a model with two separate coal feeds with parallel circuits for the oversize, intermediate and fines streams. The genesis of this model is more than 30 years old but recent improvements in mixed integer programming solvers make a full mixed integer formulation practical. The original model began as an enumeration of cut points with arbitrary rules for product allocation. The product allocation was improved in a linear programming formulation by Gunn (1982) and Sarker (1991 and 1995). Current mixed integer programming capabilities make it possible to replace the enumeration aspects and solve directly as a mixed integer programming problem. The current implementation uses a general purpose modelling language to formulate the model. Open source and commercial mixed integer programming solvers are compared

Sep 26, 2011