Search Documents

By M. E. Wadsworth

The Michigan State College of Mines was established ten years ago last September as the fourth and last of the iustitutions of Michigan which are devoted to higher education. From the moment of its inception its single object has been to send out men who are qualified to take active part in the development of the mineral wealth of our State and nation, and any study which is essential to this end will not be found wanting in its courses of instruction. The institution has been singularly happy in its location. It is an axiom of modern education that any school which is to obtain the greatest return for the money and energy spent in

Jan 1, 1898

By Edward A. Vitunac

The emerging importance of pneumatic conveying systems for bulk materials is largely due to the economic advantages such systems frequently exhibit when compared to alternate methods. Included in these advantages are relative simplicity, ease of installation, flexibility, ease of maintenance, cleanliness, safety and ease of automation to the degree desired. In general, installed costs favor a pneumatic system when compared to competing mechanical systems if the transporting distances are long or to and from many points. In addition, supplemental use such as cooling, heating, or drying may supply the incremental value required to justify its selection.1 The main disadvantages of a pneumatic system are the greater horsepower required per unit weight of material conveyed, material limits in abrasiveness, and density. In addition, material breakage tends to increase at changes of direction and at any obstruction such as that caused by the imperfect butting of two pipe sections in the conveying line. Classification of the material at the discharge may also cause problems in dusting and segregation. Materials weighing less than 4 lb per cu ft tend to cause feeding and collecting problems although they can be conveyed easily. Material between 4 lb and 20 lb per cu ft can be handled with fewer problems, but flow rate is hard to predict. The 20-60 lb per cu ft range offers best results, whereas materials of over 60 Ib per cu ft tend to drop out of the air stream and settle in the pipeline unless careful pro- visions are made to prevent this.2

Jan 5, 1968

By Leo Dana

INTRODUCTION THE object of this paper is to discuss the factors and conditions that affect the observed values of the melting points of refractory materials and to describe practical methods for the determination of these points. While it appeared to be necessary to discuss some of the general properties of silicates and refractories, these subjects have been entered into only in so far as they relate to the melting point and its determination. Refractory materials such as fireclays, firebricks, and minerals generally, may be considered to be composed of compounds of metallic oxides, solid solutions of the oxides, the pure oxides, or mixtures of the three classes together with small amounts of a variety of chemical compounds. The oxides of silica and alumina occur most commonly in refractory materials; in combination with. these, oxides of the alkali earth, the alkali, the iron group, and the rare earth metals are frequently found.

Jan 9, 1919

By L. B. Bramlett, S. L. Reyher, G. G. Southard

The Archean (2.65 billion years) aged Canning Stock at Copper Mountain, WY, contains an average of 20 ppm U. The North Canning and Fuller deposits occur within the enriched interibr of the stock. Post-Laramide development of supergene enrichment blankets occurred in 25-100 m (82-328 ft) crushed zones. Hematite and chlorite accompany pyrite and sooty pitchblende in the mineralized zones. Reduction mechanism proposed for deposition of pitchblende are sulfides, hydro-carbons, bacteria, the water table, or some combination of these. Abundant tar-type organics appear to have preserved the enrichment blankets from degradation. Trace element and radio-metric data define target zones, but exploration models focus on favorable structure.

Jan 1, 1983

By B. W. Frazier

AT a recent meeting of the North of England Institute of Mining and Mechanical Engineers, during a discussion upon the compression of air, attention was called to an apparent anomaly in the phenomena attending the compression. At a subsequent meeting this apparent anomaly was explained by Prof. Herschel, and all the facts observed shown to be strictly in accordance with the laws of thermodynamics. Upon reading the report of the discussion in the published transactions of the society, it occurred to me that an attempt to determine mathematically the amounts of energy (whether in the form of heat or of work) expended and absorbed in compressing air, and causing it to perform work by expansion, might prove of use to some who have not access to any treatise upon the application of the laws of thermodynamics to the compression of air, and who have not the time or the inclination to make such application for themselves. The apparent anomaly noticed was this: If air be compressed, and at the same time, by the sufficient application of a cooling medium, kept at a constant temperature, the indicator diagrams in the

Jan 1, 1874

By Northcutt Ely

International developments affecting foreign in- vestments in 1960-61 were many, varying from region to region and differing with respect to various categories of investments. Total value of U.S. private investment abroad in 1960 was approximately $32.7 billion, an increase of $2.9 billion over 1959. Production and distribution of mineral resources was, by a sizeable margin, the most important function of American capital working in foreign countries in 1960. Investment in mining or petroleum interests totaled approximately $14 billion, or 42% of all direct foreign investment. In- vestments by industry for 1960 were as follows: Petroleum-10.9 billions, Mining-3.0 billions, Manufacturing-11.2 billions, Utilities-2.5 billions, other-5.1 billions. American investors found Canada and Latin America to be most desirable in 1960 with the greatest percentage of American capital in all areas centered in the petroleum and mining industries. The areal breakdown of total American investments is as follows: Canada-$11.2 billions, Latin America-$8.4 billions, Western Europe-$6.6 billions, Middle East-$1.2 billions, Far East-$1.2 billions, Africa-$.9 billions, other areas-$3.2 billions.

Jan 3, 1962

By P. F. Ahner, Leonidas Petrakis, Fred E. Kiviat

High gradient magnetic separations (HGMS) is a recently developed technique in which magnetic micron-size particles contained in a flowing fluid medium can be extracted from that medium. HGMS is presently utilized on a commercial scale in the kaolin processing and steel industries, and is being investigated for solid-liquid separations in numerous other processes. The performance characteristics of HGMS in the kaolin and steel industries are briefly summarized. A discussion of HGMS performance with respect to solids removal in a coal liquefaction process is presented to illustrate its applicability to difficult solid-liquid separations. Here, the properties of the solids suspended in the liquified coal are such that the HGMS separator achieves over 90% solids removal. The optimization of the HGMS operating parameters to yield these results will be discussed. To further illustrate the potential of HGMS, its performance with respect to the removal of oil and solids (over 98% removal) from a petroleum refinery process water effluent stream will be briefly considered.

Jan 1, 1980

By R. H. Raring, F. E. Martin

A high speed gas quenching dilatometer useful in studying phase transformations in low alloy steels is described. Changes in specimen length are measured by means of an electrical micrometer tube. The maximum instantaneous cooling rate is approximately 5000°F per sec; the maximum average cooling rate from 1650' to 950°F is approximately 2900°F per sec. Data for steels of 0.11 pct and 0.67 pct C content are included. KNOWLEDGE of phase transformations as they occur in an alloy under conditions of continuous cooling affords valuable insight into its properties. The transformation characteristics during continuous cooling of steels of high hardenability, which decompose entirely to martensite at fairly slow cool-

Jan 1, 1957

By M. J. Duggin

Evidence is produced below to show that the carbide "Mn,C," reported by Kw,and ersson' is really a mixture of two carbides. One is an Fe-Mn carbide which is probably isomorphous with hexagonal Mn15C4, reported by Bouchand and Pruchart.' The othev is a tetragonul Fe-Mn carbide with cell dzmensions close to those reported previously by the author3 for an Fe0.1Mno. carbide. IN a recent investigation several Fe-Mn carbide specimens, each weighing about 5 g, were prepared in a manner previously reported.3 Debye-Scherrer X-ray photographs were taken of at least two samples from different parts of each specimen using a 114.6-mm-diam camera. The exposure time was 2 hr using filtered chromium radiation, a tube voltage of 35 kv and a tube current of 10 ma. In the case of one specimen, which contained nominal weight percentages of iron, manganese, and carbon of 9.40, 84. 6,, and 6.0, respectively, duplicate chemical analyses indicated f1.2 and 5.5 wt pct C to be present in the two samples taken of the specimen: no graphitic carbon was detected. One powder-diffraction pattern of this specimen indicated the presence of the tetragons: carbide reported earlier,3 (a = 6.772A, c = 9.427A), plus cementite (O), plus an unknown structure. The second powder-

Jan 1, 1970

By Henry Carlisle

W. W. Mein: One of the most amusing things in Nevada City – I was born and was going to school there - was that my mother made overcoats for us, and because they were different from other boys’ overcoats, we’d hide them under a bridge and pick them up on the way home. I left Nevada City with my parents when I was about eleven years old, and moved to Oakland. This was caused by the closing down of the hydraulic mines and my father being send to the El Cayo mine in Venezuela, which was then one of the richest gold mines in the world. Hamilton Smith operated the hydraulic mines in California, and when they were closed down by the Sawyer decision, he was persuaded by the Rothschilds to go to London. There, together, they formed the London Exploration Co.

Jan 1, 1964

By John E. Sherborne, William M. Newton

THE relation between the properties of electric logs and the fluid used in drilling a well is briefly discussed in this paper, and the fact that the resistivity of the drilling mud and its filtrate can appreciably affect such logs is shown. Apparatus was designed and a procedure established to determine the effect of various factors on the resistivity of drilling mud. Five muds commonly employed in California were tested and the following observations were made: I. The effect of raising the temperature from 80°F. to 180°F. is to decrease the resistivity of the mud or filtrate approximately 50 per cent. 2. The resistivity of the mud in most cases closely approximates that of its filtrate. 3. The change in the resistivities of muds caused by the addition of chemical is not the same function of the amount of chemical added for each mud. 4. The effect produced by increased sodium chloride content is to reduce markedly the resistivity of the mud and its filtrate. 5. Weighting materials, such as Baroid and limestone, tend to increase the resistivity of drilling mud. 6. Cement and counteracting reagents reduce mud resistivity.

Jan 1, 1942

By N. J. King, R. F. Hadley

Alluvial valley floors constitute a valuable land resource and are important to ranching operations in the semiarid western United States. This resource may be in jeopardy locally if the alluvial deposits are disturbed by surface mining of coal deposits. Erosion problems caused by poor land-use practices can cause trenching of the unconsolidated alluvium with a consequent lowering of the water table and depletion of soil moisture needed to support vegetation. Historical evidence of this sequence of events is abundant in the geologic literature and serves as the basis for assessing potential impacts of surface mining. The potential geomorphic impacts of surface mining on alluvial valley floors with regard to fluvial processes are. (1) disruption of the longitudinal profile followed by valley trenching and high sediment yields downstream, and (2) replacement of the excavated alluvium with unconsolidated material that does not have similar physical characteristics and may be susceptible to erosion. Mining may disrupt the existing hydrologic framework affecting stream flow, ground-water levels, and water quality of both surface and ground water. Although functional hydrologic and geomorphic processes are similar, each valley represents a complex environment that does not submit to broad generalizations.

Jan 1, 1981

By John F. Blandy

IT is not my intention in this article to consider this subject in the light of the geographer or geologist, but rather in that of the mining engineer, and to endeavor to show the necessity and value to him of studying the minor details of the field or district in which he may be engaged. It has been said by a distinguished geologist that "the natural boundaries of the geographer are rarely described by right lines. Whenever they occur, however, the geologist may look for something remarkable." And again ; " Physiognomy is no idle or doubtful science in connection with geology. The physiognomy of a country indicates almost invariably its geological character." Our country furnishes examples enough of the truth of these remarks, and in no part of it is it so beautifully illustrated as in our own State, which has been so ably described by Prof. Lesley in his admirable little work on the "Topography of Coal." As the great mountain lines become guides to the geologist in determining and mapping out the geography of the formations, so do the minor details of topography become guides to the mining engineer in conducting his explorations, discovering of dislocations, and determining the character of the deposits which are the object of his search. It is therefore requisite that he should, whilst making his surveys, pay the strictest attention to every variation of the landscape and surface of the ground. Until he has mapped out every feature he may be unable to read the geological changes which may have

Jan 1, 1873

By A. Blake Caldwell

Northwest frontier is here defined as Alaska, the Yukon, the Northwest Territories and northern British Columbia. The mineral potential of this area is great and will unfold in the decade ahead but now the largest single producer is the Pine Point lead-zinc mine in the NWT about 1200 km north of Edmonton, Alta., close to the south shore of Great Slave Lake. The mill, initially designed for 4540 mtpd, was expanded to 7250 mtpd in 1969. This operation is described in detail in Mining and Concentrating of Lead and Zinc, Vol.1, Chapt. 17, SME/AIME in the article by W. H. R. Gibney.

Jan 1, 1971

By Zay Jeffries

IN this paper, it is proposed to outline a method for the determination of melting points of those metals and alloys having high fusion temperatures. The application of the method as used to determine the melting points of alloys of tungsten and molybdenum will be given. It will be seen from these results that tungsten and molybdenum form a completely FIG. 1.-PARTIAL SECTION OF APPARATUS USED TO DETERMINE MELTING POINTS OF TUNGSTEN AND MOLYBDENUM ALLOYS. isomorphous series. This is also verified by the accompanying photomicrographs. Tungsten and molybdenum have been found to crystallize in the salve system, namely, isometric, and the crystal units are cubes. These determinations were made by examining etching pits in the pure metals.

Jan 7, 1916

By D. W. Fuerstenau

THE object of this article is to point out the experimental relationship which exists among contact angle, adsorption density, zeta potential, and flotation rate data. In each of the experiments discussed in this article, the surface properties of quartz, as a function of pH, were measured in solutions to which constant quantities of dodecylammonium acetate were added. Morrow1 and deBruyn2 worked with solutions containing 4.08x10-5 moles per liter, whereas Fuerstenau3 and Seele worked with solutions containing exactly 4x10 moles per liter, but this difference is not significant. The pH of the solutions was regulated with HCI or NaOH in all cases. In each case, the addition of collector was constant, but the concentration of dodecylammonium ions decreased because of the formation of dodecylamine at higher pH values2 Contact Angles: Gaudin and Morrow1 presented data for the contact angle of quartz in solutions containing 4.08x10-5 moles of dodecylammonium acetate per liter between pH 2 and pH 10.15. Using the same captive bubble techniques, the writer measured contact angles on quartz in solutions containing 4x10-5 moles of dodecylammonium acetate per liter at pH values ranging from 9.9 to 13.2. Both sets of data are presented in Fig. 1, in which the contact angle in degrees is plotted as a function of the pH of the solution. From pH 2 to about 8, the contact angle increases slightly with increased pH, but further increase in pH causes a sharp rise in the contact angle to a maximum of about 80º. At pH values above 11.6, the contact angle drops sharply, reaching zero by pH 12.6.

Jan 12, 1957

By Frederick J. McGarry, Fred Moavenzadeh

An experimental investigation of the thermal and mechanical responses of rock materials to laser radiation is described. Specifically, the following three topics have been studied in detail: 1. Temperature measurements on thin discs subjected to laser radiation. 2. Strain measurements on thin discs subjected to laser radiation. 3. Observation and evaluation of cracking and spalling phenomena in constrained and unconstrained thin discs respectively, subjected to laser radiation. In conjunction with the experimental work done, use was made of a heat flow analysis and a stress analysis program developed for this purpose. It was possible to theoretically predict the thermal and mechanical responses of a rock specimen to laser radiation and then compare them with experimental observations. Good correlations were obtained.

Jan 1, 1971

By A. M. Gaudin, R. T. Hukki

PREVIOUS work on the principles of comminution has shown: (I) that the surface produced is proportional to work input (Rittinger law, 1a-3); (2) that there is regularity to the weight distribution of the fragments according to size.4-10 In this paper it is brought out that the surface on the fragments is distributed in definite and simple relation to size. The experimental work has involved: I. Construction of an apparatus capable of measuring the surface of mineral fragments independently of the chemical composition of the fragments and independently of the site of the surface; 2. Refining the methods available for measurement of particle size; 3. Designing and building a crusher capable of operating on very small quantities of mineral, if necessary on single crystals, and in such fashion as to minimize handling losses of material. Complete experiments have been carried out with massive quartz and individual quartz crystals. Partial experiments, lacking surface measurements, have been made with glass spheres, galena, sphalerite, fluorite, salt and coal.

Jan 1, 1944

By J. Price Wetherill

THE coal-seams that are worked vary from 32 to 100 feet in thickness, and occur at all angles of inclination, but are never flat for any great extent. They contain coal, slate, and an unsolidified coal, called dirt by the miners, in various proportions, a uniform seam of coal alone being rare. The upper walls are composed of conglomerate, sandstone, or slate; the first two hard and solid in texture, and withstanding the action of the atmosphere and moisture sufficiently well to offer but little trouble to the mining operations ; while the latter crumbles rapidly, owing, in part, to the decomposition of iron pyrites which it contains in large quantities, and in part to its own friable character, and requires constant care to avoid accidents to the men working below it, and to prevent its mixing with the coal mined. The floors are composed of slate. As in all mining operations, the. general system pursued is to reach with a permanent outlet such a point in the seam as will

Jan 1, 1877

By A. L. Field

A. W. FAHRENWALD, Socorro, 'N. M. (communication to the Secretary*).-When asked to discuss Mr. Feild's paper, I felt most highly complimented to have the privilege of commenting on such a worthy and needed piece of apparatus. In consideration of the importance of the viscosity of blast-furnace slags and the relation existing between the' melting point of a slag and its viscosity, the introduction of this apparatus should be a welcome means or assistant in the study of the physical properties of a slag. Up to the present time, it is A fact that this side of the practical working of the blast furnace has been sadly neglected by those investigating slags. It is easily seen that the fluidity of a slag is of as great importance as its melting point. It is not necessarily true that a slag having a low melting point will have a correspondingly low viscosity or be highly fluid. For example, a slag having a melting point of 1,100° C. may have to be superheated to, say,1,300° C., in order to have as high a fluidity as another slag whose melting point is, say, 1,250° C. The latter in this case would be the more economical. This point has been brought out very nicely by Mr. Feild. Before discussing this paper further, I think it will be well to outline some of the points, a discussion of which may be in order:

Jan 3, 1917