Search Documents

By S. F. Shaw

IT IS generally recognized that the natural gas absorbed in petroleum plays the leading r6le in moving the oil through the sands to the well and supplies the energy that delivers the oil to the surface when the wells are flowing. It is the purpose of this paper to note the amount of oil that could be lifted by this gas if 100 per cent. efficiency were obtained and the efficiencies actually obtained in the use of this gas. An article in MINING AND METALLURGY,' stated that in a Wyoming field, with a pressure of 300 lb. per sq. in., there would be absorbed 65 cu. ft. of gas per barrel, or 1.55 cu. ft. per gal. of oil. The writer does not know if data have been obtained, by experiment, for pressures beyond those indicated in this article, therefore, for the purpose of illustration, he has projected this curve to obtain figures for pressures greater than 300 lb., although probably experiment will show that the extended line is not quite correct.

Jan 1, 1926

By E. W. Engelmann

A NEW and interesting type of drier has been developed and operated at the Magna plant of the Utah Copper Co. for the past year for the drying of a filtered concentrate in the molybdenum recovery plant of this company. The several units installed have ranged from 12 to 30 in. in width, and from 14 to 30 ft. long. Their economy was immediately apparent after the first one was installed. The machine is not only low in capital cost, but has proved efficient for the drying of fine concentrate at low operating cost. The Utah vibrating drier consists of a steel conveyor trough supported on flexible reeds from a structural steel foundation anchored in concrete. The steel pan, which is also the drying surface, is vibrated by a heavy Utah electromagnetic vibrator fastened either to the head or discharge end of the pan. The vibration thus obtained agitates the material and causes it to be conveyed over the heated surface.

Jan 1, 1938

By Anson Hayes

FOR the purpose of the following discussion the word "research" is interpreted as including all phases of development work on methods of manufacture, metallurgical characteristics, and uses of iron and steel. Research in the iron and steel industry then includes both plant re- search and laboratory research. Since iron and steel came into being, the steel consumer's plant and the steel producer's plant have been important factors in the development of the steel industry. Good minds have always been associated with both consumer and producer plants, so marked progress was made in the industry even when these were the only types of research and development groups in action.

Jan 1, 1937

By Dr. Hermann Wedding

Albert Ludwig Serlo was born February 14, 1824, at Crossen-on-the-Oder. After completing his school-studies and his training as a mining official, he received in 1851 an appointment as Royal Manager of salt-works (Salinenfactor) and member of the Administratioll of Salines at Konigsborn, near Unna, Westphalia. The issue of new regulations for the training of higher State officials in the Department of Mining, Metallurgy and Salines, led him to pass in 1856 a special examination for the rank of Assessor, in consequence of which he was called to Berlin, to serve for a few months as an assistant in the Ministry of Commerce, which had charge of mining, etc. In the same year he became Bergmeister and member of the mining administration at Bochum, Westphalia, and in 1858 Oberbergrath and member of the provincial administration, called the Oberbergamt, having its headquarters located at Dortmund. In 1861 he was appointed Director and head of the newly-reorganized mining

Jan 1, 1900

By J. B. Newsom

IN the September 1936 issue of MINING AND METALLURGY the pioneer work of boring a 5-ft. shaft to a depth of 1125 ft. at the Idaho Maryland mine in California was described. Later, a Bureau of Mines Information Circular (No. 6923) gave additional data. In re¬cent months still further progress has been made in this technique through the sinking of a 5 1/2-ft. shaft for Pickands, Mather & Co. at their Zenith mine, Ely, Minn. The present work was done with new carefully designed equipment and several experienced men so that progress, as shown below has been much better:

Jan 1, 1938

By J. M. Locke

Bruckner's revolving cylinders for roasting ores, etc., are now used at a number of the mills in Colorado and New Mexico, for the purpose of roasting and chloridizing silver ores, with highly satisfactory results, even from those cylinders of small size, erected before the many improvements of recent date. AS examples of the larger improved cylinders, reference can be made to those erected at the Tennessee Reduction Works, Silver City, Grant County, New Mexico, and those which were built, in 1871, at the celebrated Caribou Silver Mill and Mines, Colorado, a mining enterprise which has proved so satisfactory as to have been lately sold to a Holland company for an enormous amount. These cylinders, as now constructed by Messrs. Lane & Bodley, of Cincinnati,,Ohio, are shown in Plate 111, in which Fig. I is an elevation in perspective, Fig. 2 a longitudinal, and Fig. 3 a transverse section. Fig. 4 is a sketch of a mill, with Bruckner's cylinder. The exterior of the cylinder is a shell of boiler iron, 12 feet long by 5 feet 6 inches in diameter. The ends are partially closed with similar material, leaving in the centre a circular opening about 2 feet in diameter, bounded by a flange projecting several inches. Upon one side is placed an opening closed by a hinged door. Upon the outside of the cylinder are bolted three bands, as shown in Fig. 1, in which the section of the first is square, and that of the third semi- . circular; the second, or middle band, is a strong spur gear. Passing through the cylinder are six pipes parallel to one another, in a plane at an angle of 15" to the axis of the cylinder; these pipes also lie in this plane at an angle of from 30" to 35' to the longitudinal .axis of the plane, as shown in Fig. 2, where the internal arrangement of the cylinder is seen, a perforated diaphragm being formed through part of the cylinder by means of perforated plates placed between

By Raymond C. Moore

The oil-producing districts of Kansas comprise the northern portion of the so-called Mid-Continent field. As shown in the accompanying map, these districts are located chiefly in the southeastern and south central parts of the state. A considerable area in southeastern Kansas, extending northward nearly to Kansas City, has long been known as oil territory, the productive wells being distributed in patches or spots of irregular size and shape, the location of which is controlled by conditions of rock structure, and by the texture and porosity of the "sands" beneath the surface. In south central Kansas, there are a number of producing fields, the location of which appears to be controlled chiefly by well-defined structure. The most important districts are those in Butler County, especially that in the vicinity of El Dorado, which was for a time the most productive district in the entire Mid-Continent field. Recently new production of importance has been brought in the vicinity of Peabody and present development is active to the north across Marion County. Tests in the western parts of Kansas have not been successful in finding new petroleum fields. Histoby The first well drilled for petroleum, in Kansas, was near the town of Paola, Miami Co., about 40 mi. southwest of Kansas City, in the summer of 1860, only a few months after the completion of the famous "Colonel" Drake discovery well in Pennsylvania. Kansas appears to be the second state to engage in a serious attempt to find oil by drilling. The Civil War caused the temporary abandonment of attempts at oil development in the state. It was in the vicinity of Paola, where numerous oil seepages had been observed, that the first well producing oil in commercial quantities was drilled,' where also gas was first piped to the city for commercial use. Prospecting spread southward into Linn County and northward into

Jan 1, 1921

CONTENTS PAGE CARMICHAEL, NORMAN, and KIDDIE, JOHN.-Development of Mine Transportation in Clifton-Morenci District. Discussed by Norman Carmichael, Charles Legrand, B. B. Gottsberger 1 BARER, THOMAS C.-Fresnillo - Glory-hole Mining Practice. Discussed by Charles A. Mitke, B. B. Gottsberger, E. R. Thomas, Enoch Perkins..: 3 BRADLEY, P. R.-Estimation of Ore Reserves and Mining Methods in Alaska Juneau Mine. Discussed by R. M. Raymond, A. H. Rogers, Enoch Perkins, H. G. Moulton 6 BIRCH, STEPHEN.-Geology and Mining Methods of the Kennecott and Beatson Mines. Discussed by R. M. Raymond, Alan M. Bateman, Enoch Perkins 8 LEES, CHARLES E.-Mining Methods and Costs at the Iron Cap Copper Co., Copper Hill, Ariz. Discussed by A. L. Walker, A. Neustaedter 10 BELL, CHARLES N. -Mining Methods of the Telluride District. Discussed by Charles S. Hurter 10 Development of Mine Transportation in Clifton-Morenci District Discussion of the paper of NORMAN CARMICHAEL and JOHN KIDDIE, presented at the New York Meeting, February, 1924, and issued, as. Paper No. 1310-M, with MINING AND METALLURGY, March, 1924. NORMAN CARMICHAEL.-We realized the objections too the gable-bottom car, but were almost forced to its adoption by the same reasons that caused us to retain the 20-in. gage. To use another car would have meant a vast number of changes, for our transportation system was quite extensive; all mine chutes and ore bins were arranged for that car. Had we been laying out, new works, many of our decisions would have been different. MEMBER.-If you were planning it now, would you not put in box bottom cars with a rotary dump? NORMAN CARMICHAEL.-We surely would. One objection to the gable-bottom car is the spill. No, matter how carefully the cars are kept up,: there is always leakage and spill. The cost of keeping and maintaining the cars in a good state of repair, so as to keep that loss at a minimum, is not necessary for a box-bottom car.

Jan 6, 1924

By John B. Knaebel

The annual Jackling Award Lecture, sponsored by the Society of Mining Engineers of AIME, is intended to honor and commemorate one of the greatest mine-makers of all time, an innovator whose vision and determination made ore out of waste rock. He ushered in a new philosophy of mining which revolutionized some segments of the industry and notably affected our economy generally. To have been asked to given the Jackling Lecture this year is an honor that I scarcely deserve, but which I have accepted in humble gratitude. Although it is true that "many a mine has made the man," it is also true that while ore bodies are found, mines are made. That statement has been hammered into my skull many times by a man whose own career exemplifies its truth, a man who has been first and last a steadfast friend, who for a while was my boss and mentor, and who as one of this country's great mining geologists has laid his hand to the making of many a mine. I will doubly cherish the memory of the honor bestowed upon me because the presentation of the Jackling Award was made by this man. After the Lord made Dick Hunt he threw away the mold. Metals and other mineral products are essential ingredients of the social economy of the modern world. No well informed and thoughtful person can doubt that they will be indispensable to mankind as long as the fabric of civilization as we know it today can be held together. They are mined from ore bodies, which, unlike some other kinds of bodies, are physically inorganic and wholly incapable of reproducing themselves. Since in time they become mined out, an endless procession of new producers must be made by someone if the fundamental needs, to say nothing of the not so fundamental whims of an affluent society, are to be gratified. In saying that these mines must be made, I mean exactly that. It is my purpose to comment upon some of the problems we must cope with in making them. I shall try to avoid dwelling needlessly upon aspects of new mine development with which most people in this business are thoroughly familiar, and will attempt to discuss in a useful way some of the newer and more significant features of the economic climate in which these endeavors must be conducted. To begin with, an Almighty force put the ore into the ground, and selected the places in which to put it. Mankind was not consulted. Beyond that stage, however, mankind must find the ore deposits and contrive to extract their contents and put them into useful service. In doing this, he must use tools and techniques devised by man to overcome obstacles created in part by nature, but also in part by man himself. And most importantly of all, in making the tools and applying the techniques, he must use people. In the whole process the most pliable ingredient at hand-and also the most unpredictable-is people. Mines play out, and men die. As time goes on, we will have new mines, and they must be made by new men. The Environmental Dilemma It is perhaps timely to touch first upon the newest and in many ways the most potent consideration affecting the feasibility of developing new mines-the problems related to protection of the environment and to the

Jan 1, 1973

By Walter Kauenhowen

Germany's crude oil production during 1935 totaled 3,007,711 bbl., an increase of 36.6 per cent over the 2,202,214 bbl. produced in 1934. The Nienhagen-Haenigsen field furnished 77 per cent of the total 1935 production. Cumulative production figures for Germany's two most important oil fields, Wietze and Nienhagen, show that during the period from 1872 to the close of 1935 the Wietze field produced 13,325,536 bbl. and the Nienhagen field 9,340,870 bbl. Table 1 gives statistics of German production since 1928, arranged both by fields and by oil provinces. Fig. 1 demonstrates the production of the various German fields since 1890. New Fields Discovered During 1935 five new fields came into production. The first of these, the Moelme-Hoheneggelsen field near Hanover, was opened up in April. This region has been sporadically drilled for oil since 1882, but not until 1935 was production on a commercial scale obtained. The oil comes from Mesozoic sandstones on the flanks of a shallow salt plug. Also during April, oil was found in commercial quantities in the Rhine valley at Forst, near Bruchsal. Tertiary and Mesozoic sandstones cut by faults of the Rhine Graben form the reservoir structures in this area. In July a wildcat well drilled on the Fallstein structure, a broad Triassic anticline near Halberstadt, came in as a producer from Permian (Zechstein) dolomite. In September commercial oil mas found at Gifhorn, near Braunschweig, in Wealden sandstones associated with a shallow, geophysically discovered salt plug. During the same month production was obtained at Heide, in Holstein, from the Permian Rotlie-gendes formation, in a structural high on which oil seepages have been known for years. Drilling Activities Published information indicates that during 1935 drilling totaled 574,000 ft., as compared with 436,000 ft. in 1934; 233,000 ft. in 1933 and 151,000 ft. in 1932. The German Government is subsidizing wildcat

Jan 1, 1936

By Walter Kauenhowen

Germany's crude oil production during 1935 totaled 3,007,711 bbl., an increase of 36.6 per cent over the 2,202,214 bbl. produced in 1934. The Nienhagen-Haenigsen field furnished 77 per cent of the total 1935 production. Cumulative production figures for Germany's two most important oil fields, Wietze and Nienhagen, show that during the period from 1872 to the close of 1935 the Wietze field produced 13,325,536 bbl. and the Nienhagen field 9,340,870 bbl. Table 1 gives statistics of German production since 1928, arranged both by fields and by oil provinces. Fig. 1 demonstrates the production of the various German fields since 1890. New Fields Discovered During 1935 five new fields came into production. The first of these, the Moelme-Hoheneggelsen field near Hanover, was opened up in April. This region has been sporadically drilled for oil since 1882, but not until 1935 was production on a commercial scale obtained. The oil comes from Mesozoic sandstones on the flanks of a shallow salt plug. Also during April, oil was found in commercial quantities in the Rhine valley at Forst, near Bruchsal. Tertiary and Mesozoic sandstones cut by faults of the Rhine Graben form the reservoir structures in this area. In July a wildcat well drilled on the Fallstein structure, a broad Triassic anticline near Halberstadt, came in as a producer from Permian (Zechstein) dolomite. In September commercial oil mas found at Gifhorn, near Braunschweig, in Wealden sandstones associated with a shallow, geophysically discovered salt plug. During the same month production was obtained at Heide, in Holstein, from the Permian Rotlie-gendes formation, in a structural high on which oil seepages have been known for years. Drilling Activities Published information indicates that during 1935 drilling totaled 574,000 ft., as compared with 436,000 ft. in 1934; 233,000 ft. in 1933 and 151,000 ft. in 1932. The German Government is subsidizing wildcat

Jan 1, 1936

By Fred C. Bond

SIX years have passed since the last grindability table was published.' In that time the list has been increased with many new tests, and the development of the new Third Theory of Comminution2 has made possible the reduction of all results to a consistent work index value. In this tabulation all grindability and crushability test results are given in terms of the work index, with formulas for reversion to the older units if desired. The average values for 57 different classes of materials are listed in Table I. The total number of work index values listed is 1211, and the overall average work index is 14.42. The complete tabulation, with each test listed alphabetically both under material type and under company name, can be obtained by writing to the Allis-Chalmers Manufacturing Co., Processing Machinery Department, Milwaukee 1, Wisconsin. The work index Wi is the calculated total work input in kilowatt-hours per short ton required to re- duce from theoretically infinite particle size to 80 pct passing 100 microns, or to approximately 67 pct passing 200 mesh. The work inputs required per ton for the same size reduction of different materials are directly proportional to their work indexes, and according to the Third Theory the work input per ton is inversely proportional to the square root of the diameter of the product particles. Where W represents the work input in kilowatt hours per ton, where F is the feed size, or diameter in microns of the square hole which 80 pct of the feed passes, P the product size, or microns which 80 pct of the product passes, and Rr the reduction ratio F/P, the work index Wi is found from Rr-l 100 When the work index Wi is known, the work input W required to reduce from any feed size F to any product size P is found from W = Wi ( Rr- 1 100

Jan 1, 1954

By J. D. A. Morrow

THIS discussion relates to the distribution of coal under the direction of the U. S. Fuel Administration beginning Apr. 1, 1918. At that time a definite method of ' controlling and directing distribution was put into effect. Prior thereto, although some of the machinery utilized was in operation, especially in the few weeks immediately preceding Apr. 1, distribution had not been effectively and comprehensively organized. The writer was called to the Fuel. Administration by Dr. Garfield about the. first of February, 1918, to assume general direction of the distribution of coal for the Fuel Administration, to develop the general plans, and to obtain practical men to assist in this work and in carrying through the program finally devised. A study of the situation and conferences with the Fuel Administrator and leading men in the business made it plain that it would- he necessary to begin at the bottom, measure the undertaking, develop plans to meet the need thus shown, and build an organization to effect the distribution required. This work had to be done under war pressure in the midst of a bad coal shortage. The successful performance of such a task is always primarily a matter of putting competent men in the right places and giving, them the power and opportunity to function properly together. In the Distribution Division of the U. S. Fuel Administration, the men who were chiefly responsible for whipping plans into practical form and then for carrying out these plans were A. W. Calloway, of Baltimore, President of the Davis Coal & Coke Co., who served as the Director of Bituminous Coal Distribution; S. Lovell Yerkes, of Birmingham, Alabama, Secretary of the Grider Coal Sales Agency, who assumed general charge of distribution while the new plans and organization were being perfected and then became the Assistant Director of Bituminous Coal Distribution; Warren S. Blauvelt, of Detroit, who was Director of Coke Distribution; A. S. Learoyd of New York, Director of Anthracite Distribution, in connection with the Anthracite Committee, consisting of Joseph

Jan 3, 1919

By Kenneth L. Adams

10.3-1. Introduction. Equipment replacement or maintenance is of major concern to every company today. It can be the difference between an efficient and profitable operation or an inefficient and struggling one. Mining equipment, as everyone knows, will not last forever. Some equipment becomes obsolete before it wears out while some may be doing its intended job, yet not economically. It is a major problem for management to make the decision as to whether a piece of equipment should be repaired or replaced. There are numerous approaches to this problem; using formulas, charts, and graphs. These would be very good if all conditions were stable. Since conditions and requirements are constantly changing, an accurate observation cannot be derived from a set formula. A formula does, however, serve as a reminder to include most of the items that should be considered when evaluating old and new equipment. In the field of mining there are several questions which enter into the reasoning that are difficult to put into an equation. Some of these are: 1. Will the present equipment produce the required output of the mine, or an increase if necessary? 2. Are reserves adequate to support the purchase of new equipment? 3. Can the old equipment be repaired to efficiently continue the mining operation? 4. What is the stability of future markets for the product? Depreciation rate, or the write-off life, is a factor that can directly effect decisions on replacement. If the initial life expectancy is too long and the price of equipment is not written off when discarded, then the original investment has not been recovered. If the write-off time is too short, then the equipment is written off before replacement is even considered. In this case, the depreciation accrual is usually used to finance some other phase of the operation. In view of the increasing prices, the amount of depreciation fund is generally too small for much incentive to replace an older unit

Jan 1, 1968

By Joseph Jenson

Total United States production for 1928 was 900,364,000 bbl. as compared with 901,129,000 for 1927, or 2,466,000 bbl. per day versus 2,468,000. The three major producing areas were Texas, Oklahoma and California. Texas production increased from 217,389,000 bbl. in 1927 to 256,888,000 in 1928—an increase of 39,499,000 bbl. following an increase of 44,500,000 bbl. in 1927. Oklahoma production amounted to 249,558,000 bbl. in 1928 as compared with 277,775,000 bbl. in 1927 and 177,650,000 bbl. in 1926. California production for 1928 was 231,982,000 bbl. as compared with 231,196,000 in 1927. Production increased markedly in Venezuela and declined in Mexico. Elsewhere no great changes or declines in production were noted. New discoveries occurred in nearly all districts. The many excellent reviews of the various districts of the United States presented at this meeting, are each fully summarized and tell their own story so well that little would be gained by attempting to repeat their content here. There are certain impressions to be gathered from these papers and certain trends that are indicated by them which may better be pointed out. OVERPRODUCTION Overproduction is the most serious one of them. Efforts to avert it resulted in a measure of cooperation in the oil industry more widespread in character and more beneficial in results than has ever been recorded in any previous year. These efforts were undertaken in the closing months of 1927 and enthusiastically effected before the spring of 1928 had passed. Unfortunately, slight advances in prices during the summer months accompanied by the letting down of this sort, of effort resulted in a marked increase of production during the latter half of 1928. Successful delay in the drilling of new prospective areas was in effect in Oklahoma. California delayed some drilling and increased its shut-in

Jan 1, 1929

By P. de Vitry, Oliver Bowles

THE conventional wire saw, introduced in the slate district of Pennsylvania by the Bureau of Mines in 1927, and used thereafter with remarkable success, consists of a three-strand steel cable having a diameter of 3/1 6 or 1/4 in. The equipment, methods used, and accomplishments have been described in previous reports.1-7 Similar wire saws have been used extensively in Europe, in quarries and in shaping blocks and slabs. During the period 1932-1937, competition in European marble quarries was keen, prices were declining, and orders were not abundant. When orders were received, there was generally an urgent call for speedy delivery. Because of the diversification of demands, it was impossible. to maintain in stock marbles of the color, size, and thickness called for,, therefore the material generally had to be fabricated after the order was received. The wire saw enabled stone mills to fill. such, orders promptly. With skillful handling, 7/8-in. slabs could be cut accurately and rapidly with this equipment. It was found, however, that, as the three-strand wire became worn, the cutting speed dropped rapidly and the cut became less accurate. To overcome these difficulties the junior author of this paper, after much experimentation, developed a new type of wire consisting of a single ribbon-shaped strand, twisted as shown in Fig. I. To ensure straight sawing, the twist of the ribbon is reversed from right to left and vice versa every 25 ft. The reversal of the [ ] twist is shown in Fig. 2. This is not a new feature; it has been used to advantage with the three-strand wire both in Europe and America for several years. However, some difficulties arise in splicing the three-strand reverse-twist wire, and the claim is made that cutting is less accurate as the wire becomes worn. To make an endless belt, the ends of the single-strand wire are brazed together with

Jan 1, 1941

By J. L. Sepulveda, R. F. Yap, R. Jauregui

INTRODUCTION The Third Theory of Comminution, oftentimes called the Bond Theory, was first published by Fred C. Bond in 1952. Since then, it has been widely used in the milling industry to size crushing and grinding equipment as well as to predict and evaluate their performance. Although two other comminution theories were advanced almost a century earlier, one by Rittinger, 1867, and the other by Kick, 1885, their use was limited because they did not agree with actual commercial comminution systems (Bond, 1961). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced in particle breakage, and equals the work represented by the product minus that represented by the feed. For particles of similar shape, the crack tip length is equivalent to the square root of one-half the surface area, and the new crack length is proportional to [(1/vT - vF)]; where P and F are particles diameter of product and feed, respectively. For practical calculations, the particle diameter can be expressed in terms of the 80% passing sizes, P and F, respectively. Therefore, the work input is given by, [10 _ 10', W = Wi [7P_7F(1)] Where W = the energy input to the mill, (kwh/t) Wi = Work Index, (kwh/t) P = square sieve opening which 80% of the product passes, (microns) F = square sieve opening which 80% of the feed passes, (microns) Equation (1) is the mathematical statement of the Third Theory, or the Bond equation. Numerically, the work index is the energy required in kwh/t to reduce a given material from theoretically infinite feed size to 80% passing 100 microns. The work index of a particular material is determined in the laboratory by conducting the standard Bond grindability test. Bond developed separate tests for the rod mill and the ball mill. The simplified test method described in this paper, which is used at Anaconda Research Center to approximate the work index, is an alternative procedure to the ball mill

Jan 1, 1982

By Norman Pilling

The micrographic analysis of silicon steels is possible if a dilute solution of nitric acid and methyl alcohol in nitrobenzol is used. The action of this reagent differs from that of sodium picrate in that there is no persistent deep-seated staining and the solution is used cold. THE technical difficulties hampering the metallographic analysis of silicon steels are chiefly the result of the extreme corrodibility of these alloys. The addition of silicon to iron in increasing quantities, up to about 6 per cent., rapidly increases the susceptibility of the alloy to chemical attack, not only in acid solution, but in water. This renders the preparation of metallographic sections very difficult, because of a non-selective attack upon the finely polished surface by the water used as a lubricant in polishing. This water attack masks the true structural details revealed by suitable etching reagents. It is thus necessary to use alcohol as a polishing lubricant in the last stages of preparation and to avoid all etching reagents having an aqueous base. A specific reagent for the identification of iron carbide in ferrous alloys, and the one hitherto used almost exclusively by metallurgists, is an alkaline aqueous solution of sodium picrate, which stains this constituent selectively. Its application to silicon steels has not proved successful, as its distinctive selective action is more or less completely hidden by the general attack of the aqueous solvent on the silico-ferrite, greatly accentuated by the fact that this reagent must be used at its boiling temperature (105° C.). Thus, a powerful metallographic aid to the study of the higher silicon alloys, such as transformer steels, is lost. A new reagent has been developed for the purpose of overcoming this difficulty. It is with some hesitation that the list of etching reagents, already overburdened, is increased, but the properties of this new reagent are advantageous in several ways and a definite field for it may be found in the metallography of ferrous alloys.

Jan 1, 1924

By W. M. Myers

THE hydraulic properties exhibited by the calcination products of certain limestones were recognized at an early datemore than 2000 years ago. It was known that calcined limestone with the addition of other minerals would react with water and produce an insoluble and stable product. This material could be cast in desired forms or could be used as a cement for the unification of other materials in large masses or for bonding brick or masonry structures. Cements are essentially mineral glues and it is their ability to unify other materials plus their fluidity when first mixed with water, enabling the mass to assume any desired shape, that has made them so extraordinarily useful to modern industry. Like other glues, cements do not exhibit their maximum strength when used alone and only when mixed with proper aggregates do their optimum properties appear. The resulting concrete, a mixture of cement, mineral aggregates and frequently of reinforcing steel, exhibits the most desirable properties of the individual constituents with regard to tensile strength, stability and permanence. The speed with which such mixtures can be -prepared and installed in place with mechanical equipment has facilitated their adoption by the engineering profession concerned with the construction industries. The development and application of improved methods of manufacture have resulted in such economies that the finished product can be sold at a remarkably low price. In addition, the necessary raw materials are of such common occurrence and wide geographic distribution that the manufacture of cement was established in 34 of the 48 states by 1946. Plants under construction will add to this number. In recent years the industry has been characterized by the development of a number of new cements designed to possess special properties essential for use in unusual environments. These have introduced the use of some new raw materials and also have complicated the processes of manufacture. In the following pages, the major varieties of cement of commercial importance are treated in the chronological order of their appearance on the market.

Jan 1, 1949

lv. H. Blauvelt, Great Falls, Montana (communication to the Secretary): In his remarks on Mr. Stetefeldt's paper (Trans., xxiii., 587)) Mr. Goetz observes: " Trouble experienced with producers at Great Falls influenced me to try Taylor producers instead of those of Wellman. But recent reports show that the Wellman producers work better, besides coating nearly 50 per cent. less than Taylor producers of equal capacity. Indiana and Illinois coals cannot be used in the Taylor producers by reason of the large size and hardness of the clinkers which they form." I think that Mr. Goetz must have been misinformed regarding the work of this producer in Illinois. One of the large mauafacturing concerns in that State, the Illinois Zinc Company, situated at Peru, which uses a coal mined in the vicinity, tried one Taylor producer, some four years ago, in competition with those of an older type, which it had been using. As a result of this trial, the company has now thirteen Taylor producers, which have been in operation for about three years. A recent report from these works says that the Taylor producers have largely reduced the loss of coal through the grate, and have also improved the quality of the gas, as compared with that produced from the same coal in the producers of the older type. This Illinois coal is, perhaps, the worst in the country for making gas; since, besides containing from 20 to 40 per cent. of ash, it carries a large quantity of pyrites, so that the clinkers are large and extremely hard, and the capacity of the producer is most severely tested.

Jan 1, 1895