Search Documents

By Gen-ichi Nakazawa, Masamichi Fujimori, Ichiro Doi

INTRODUCTION The major products of nickel industry in Japan are the electrolytic nickel (E-Ni), the ferro-nickel (Fe-Ni) and the nickel oxide sinter (NOS), totaling in production to 90 - 100 X 103 tons/year in terms of pure nickel content, and sharing approximately 20% for E-Ni, 10% or less for NOS, and the rest for Fe-Ni. The raw materials to be used for these products depend totally upon the imports from abroad; matte, the raw material used in the production of E-Ni, is from Australia and Indonesia; matte for the NOS is from Indonesia and New Caledonia; and garnierite, the raw material for Fe-Ni, is imported in bulk from New Caledonia, Indonesia and the Philippines. This report describes the acquisition of these raw materials, the production processes, trend of supply-demand, problem areas and the measures taken, and so forth, in connection with the nickel industry in Japan. ELECTROLYTIC NICKEL 1. History The nickel industry in Japan began in 1939 by the Sumitomo Metal Mining Co., Ltd. (SMM) with 150 tons E-Ni/month under the blast furnace smelting and the metal anode electrolysis. This was temporarily suspended after the end of last World War II, but resumed in 1952 with garnierite of New Caledonia as a raw material. Since then, the production capacity has been expanded incidentally to the increase of demand. However, since the smelting of garnierite contained about 2% nickel was very costly, the smelting process had been changed to smelt the briquettes of the mixture of garnierite and nickel sulfide concentrate imported from Canada and Australia. In 1975, this smelter was closed, and SMM's nickel refinery used matte from Western Mining Corp. (WMC) of Australia as a raw material. The refining process had been the metal anode one. The crude nickel oxide derived from roasting the high grade nickel matte had been melted and reduced with coke in the electric furnace and cast into anode. In 1970, a new refinery was constructed to produce 1,000 tons Ni/month under the matte anode process, and further, in 1976, the old refinery was converted into the matte anode process, thus resulting in the total production capacity of 1,690 tons Ni/ month today under the matte anode process. Shimura Kako Co., Ltd. began in 1951 to produce a little of E-Ni, and in 1955, they constructed a shaft furnace smelter with New Caledonian garnierite as a raw material to begin the E-Ni production under the matte anode process. Its monthly production reached 400 tons in 1957, but it discontinued its smeltering in 1963 to convert to the matte import from S. Le Nickel, WMC and INCO. In 1979, it changed the source of matte supply from the above to Soroako of Indonesia, discontinued the E-Ni production in 1979, and arranged for a total toll contract with Sumitomo. Meanwhile, SMM has developed a very distingished process for nickel-cobalt separation and refining by a solvent extraction method from nickel and cobalt mixed sulfide generated as a by-product in the nickel recovering process from laterite under the Nicaro process. Nippon Mining Co., Ltd. (NMC) also developed its own process. The plants under these processes were constructed in 1975, with the monthly production capacity of 230 tons of nickel and 130 tons of cobalt by SMM, and 300 tons of nickel and 110 tons of cobalt by NMC. SMM imports the raw material from the Marinduque Mining and Industrial Corp. of the Philippines, while NMC from Queensland Nickel Pty. Ltd. of Australia. 2. Production Status 2.1 Producers and materials Today, SMM holds the monthly E-Ni production capacity of 1,920 tons, of which 1,690 tons are from the matte anode process, and the remaining 230 tons are from the mixed sulfide as a raw material. NMC also uses the mixed sulfide as a raw material for a production of 300 tons/month. [ ] Most of SMM's raw material, nickel matte, is imported from WMC of Australia, partly using the Soroako matte from Indonesia. An example of material analysis is given in Table 1. Matte is a raw material for E-Ni and NOS, and the major sources of matte supply at present are Australian WMC and Indonesian Soroako, occupying ap-

Jan 1, 1982

By F. T. Davis

The annual review of mineral dressing was the subject of considerable discussion at the MBD meeting in New York last February. Because the amount of material now being published is so imposing, it was generally agreed that reviewers should try only to cite the items of importance. In order to conserve even more space, it was agreed to omit bibliographies. In reading these reviews, and those of the past two or three years, one is impressed by the advances in materials handling, the enlargement and the advances in automation of unit process equipment. Although there has been development of a variety of new concentration principles in flotation, magnetic separation, et al., the design of these principles into new plants has not been widespread. The probable reason is that the plants being built today are so large and costly that few are able to face the risk of any significant degree of experimentation. There are exceptions to this; for example, some of the chemical processes, but these are usually because there was no conventional process available. This situation should change in time as the ores amenable to our conventional methods become depleted.

Jan 2, 1967

By T. A. Rickard

In a previous paper (ante, p. 411) some description was given of the occurrence of the auriferous alluvium, extensive deposits of which lie among the highlands of the province of Otago, New Zealand. The present paper will describe some of the methods by which that alluvium is exploited. The alluvial mining of New Zealand is not yet hindered by " debris legislation." The mines are for the most part situated in a country of little agricultural value, and large rivers with rapid currents act as tailings conveyors. In time, however, steps will have to be taken to restrict the discharge into the Clutha of the tailings which are slowly raising the river-bottom. The methods of California have been followed in Otago with such alterations as peculiar local conditions require. The distinctive feature of the alluvial mining of Otago is the prominence given to the hydraulic elevator. The all-important factor in this form of mining is the control of an abundant water-supply at a suitable height above the level where it is to be utilized; and in this respect the gold-fields of the south island of New Zealand are most favora-

Jan 1, 1893

• Pellets of concentrated iron ore have been smelted in the blast furnace by Armco and the results proved satisfactory. Various percentages of pellet burdens were tried and it has been found that charges up to 70 pct pellets are workable. •In the reorganization of the Department of the Interior, two new assistant secretaries were appointed and the work divided between the four assistant secretaries. C. Girard Davidson will head a division of mineral resources including the Bureau of Mines, Geological Survey, Division of Oil and Gas and Division of Geography. •Germanium, one of the rarest of metals and a wartime strategic material, has been discovered almost in the shadow of the Capitol. The only catch is that the scattered nature of the deposits makes profitable recovery extremely doubtful. Nevertheless, experts have tabbed the concentration in the District of Columbia area the world's second richest known concentration of the element. • Cakes of mica, weighing up to 500 lb, have been formed at the Colorado School of Mines by a new "cool hearth" method. The process avoids use of crucibles and contains the molten mica in a basin of unmelted raw mixture from which the melt was derived. Crystallization takes place in this melting basin which forms a center pool surrounded by a solid cool mass of the unmelted raw mixture. • William 1. Baxter, of the International Economic Research Bureau, predicts a period of deflation because of war-essential restrictions on consumer credit and materials use. He stated; "the recent prosperity was based mainly on the sales boom in autos, homes, and household accessories." •Two subsidiaries of United States Steel have decided to build four new ships immediately to augment iron ore and limestone carrying capacity on the Great Lakes to meet demands created by the national defense emergency. •The Norfolk and Western Railway is making a complete change over to coal to drive its locomotives. •A national roster of scientific personnel similar to the one used in the last war will be established by the Office of Education, by agreement with the National Security Resources Board. The new unit, the National Scientific Register Project, will make studies of the Nation's scientific manpower supply and recommend steps to increase the numbers of skilled personnel where needed. •National Lead Co. will start construction immediately of new facilities at St. Louis, Mo., for production of titanium pigments for paints. Producers of titanium pigments have been under considerable pressure to meet all demands from paint manufacturers, particularly for titanium dioxide. •The basic criteria for deferment of reservists in civilian occupations are (1) the Department of Labor List of Critical Occupations, and (2) the Department of Commerce List of Essential Activities, both of which were announced Aug. 3. Fundamentally, the reservist deferred must be engaged in a critical occupation which is necessary to a highly essential activity, and he will be deferred only until he can be satisfactorily replaced in that occupation. A delay in call to active duty, it was emphasized, may not be considered as an indefinite exemption from military service.

Jan 9, 1950

By J. H. Jensen

Bromine is the intermediate member of the halogen family of elements between iodine, a solid: and chlorine, a gas. The name is derived from the Greek "bromos," meaning stench. Bromine is the only nonmetallic element that is liquid at room temperatures with a melting point of -7.2" C and a boiling point of 58.78" C. Reddish brown in color, it dissolves easily in water to yield a red solution. Bromine volatilizes at ordinary temperatures to a red vapor that is very irritating to the eyes, nose, and throat. Density of the liquid is 3.12 and gas weighs 7.59 gpl at standard conditions. As the element is highly active, it exists in nature only as bromide compounds. Bromine was discovered by Antoine Jerome Balard in seawater bitterns in 1826 and first prepared in quantity in 1860. Distribution Bromine is widely distributed in nature and compounds occur in solution in natural brines, in seawater, saline lakes, oil and gas well brines, and in evaporite chloride minerals. The concentration of bromine salts ranges from 60- 65 ppm in seawater to several thousand ppm in oil well brines and saline lakes. The distribution of bromine in marine evaporite minerals and in the solutions from which they crystallized was determined many years ago by H. E. Boeke (1 908). Theoretical aspects regarding the geochemistry of bromine have been published in numerous papers (Raup and Mite, 1969). Bromine occurs in solid solution in carnallite and sylvite associated in potash de- posits; in halite in salt beds; salt in oil shales; and in trona deposits. Its presence is useful as a guide in geochemical exploration. The analysis of small amounts of bromides in the presence of large amounts of chlorides is discussed by W. Schwerdtner (1963). Manganese, iron, and iodine may interfere with the determination. Other analytical methods are discussed at length in the literature (Stenger and Atchison, 1964). Sources and Reserves The sources and reserves of bromine, given in [Table 1], appear ample to meet present and foreseeable requirements in all producing countries. With the occurrence of bromine salts in sea-water and other brines, the potential for bromine production is worldwide. It has been estimated that 99% of all commercially recoverable bromine is in the ocean. However, actual subterranean brines having a higher bromine content than seawater will continue to be the preferred sources of bromine for the foreseeable future. Markets and Prices About 17% (1968) of bromine produced is used in its elemental form, with the balance consumed as bromides and bromates. The largest use for bromine is ethylene dibromide which, together with tetraethyl lead, are used as an antiknock additive in gasoline. Tetra-ethyl lead is the antiknock agent. Ethylene dibromide combines with the lead after combustion in the engine to form a volatile com- pound that escapes from the engine with the exhaust gases.

Jan 1, 1975

By David B. Reger

The discovery of prolific oil wells in old territory hitherto regarded as doubtful, if not worthless, and the rapid extension of a gas pool opened late in 1938 were the most interesting petroleum features in West Virginia during 1939. Oil activity in general was slow because of crude prices that were still fairly low at the end of the year, although substantially increased above those in January. Fewer oil wells were completed, but the average results were better than in 1938. Fewer gas wells, also, were completed, with greatly lessened average initial production. Many old oil and gas wells were abandoned, so that the total number of active wells has not changed appreciably. The account of operations, as gathered from trade journals and other sources, shows that 561 new wells were drilled, resulting in 101 new oil wells with 2261 bbl. of daily initial production; 366 new gas wells with 602,400,000 cu. ft. of daily open flow; and 94 dry holes. Besides these new wells, 61 old wells were drilled to deeper sands, with 12 bbl. and 13,328,000 cn. ft. of added production. On the new wells the oil average was 22.38 bbl. per well per day; and the gas average was 1,645,900 cu. ft. per well per day; the ratio of dry holes to completions was 16.76 per cent. From an exploratory standpoint one partly discredited oil area was revived by good new production, and another small oil pool may have been opened. Some of the results in gas exploration will require more drilling for true appraisal. It is certain, though, that one very considerable gas field in the sands of Mississippian age has been proved; and there is a probability of six new pools in the Middle Devonian shale. In the Oriskany sand (L. Dev.) the Elk-Poca pool has been extended considerably farther northwest into Jackson County; and farther north in Jackson County two widely separated wells, which may be pool openers, have been successfully completed. On the other hand, several important wildcats in various counties have been dry. Stratigraphically lower, some additional wells have been completed in the Newburg sand (Sil.) and one small producer has been completed in the Clinton sand (Sil.), the importance of which can scarcely be overestimated, because no Clinton production has previously been found in the state, although at least seven wells have been drilled through the sand.

Jan 1, 1940

By David B. Reger

The discovery of prolific oil wells in old territory hitherto regarded as doubtful, if not worthless, and the rapid extension of a gas pool opened late in 1938 were the most interesting petroleum features in West Virginia during 1939. Oil activity in general was slow because of crude prices that were still fairly low at the end of the year, although substantially increased above those in January. Fewer oil wells were completed, but the average results were better than in 1938. Fewer gas wells, also, were completed, with greatly lessened average initial production. Many old oil and gas wells were abandoned, so that the total number of active wells has not changed appreciably. The account of operations, as gathered from trade journals and other sources, shows that 561 new wells were drilled, resulting in 101 new oil wells with 2261 bbl. of daily initial production; 366 new gas wells with 602,400,000 cu. ft. of daily open flow; and 94 dry holes. Besides these new wells, 61 old wells were drilled to deeper sands, with 12 bbl. and 13,328,000 cn. ft. of added production. On the new wells the oil average was 22.38 bbl. per well per day; and the gas average was 1,645,900 cu. ft. per well per day; the ratio of dry holes to completions was 16.76 per cent. From an exploratory standpoint one partly discredited oil area was revived by good new production, and another small oil pool may have been opened. Some of the results in gas exploration will require more drilling for true appraisal. It is certain, though, that one very considerable gas field in the sands of Mississippian age has been proved; and there is a probability of six new pools in the Middle Devonian shale. In the Oriskany sand (L. Dev.) the Elk-Poca pool has been extended considerably farther northwest into Jackson County; and farther north in Jackson County two widely separated wells, which may be pool openers, have been successfully completed. On the other hand, several important wildcats in various counties have been dry. Stratigraphically lower, some additional wells have been completed in the Newburg sand (Sil.) and one small producer has been completed in the Clinton sand (Sil.), the importance of which can scarcely be overestimated, because no Clinton production has previously been found in the state, although at least seven wells have been drilled through the sand.

Jan 1, 1940

Prof. Henry M. Howe, New York, N. Y. (communication to the Secretary*):—The results presented in Mr. Mathewson's paper are of very great interest. Perhaps the most interesting is that shown in Table I. and Fig. 1, in which the arsenic decreases in 10 min. from 0.22 to 0.07 per cent. This is such a large decrease that it is to be hoped that Mr. Mathewson will verify it by repeating his tests with a matte of similar composition. This is particularly to be desired, because the simultaneous removal of sulphur appears to be very small. All three blows further agree in showing that the removal of arsenic is in the very early part of the blow. The fact that the removal of arsenic then ceases abruptly cannot be explained completely by the fact that the arsenic has fallen so low as by its lowness to resist further removal, because in the first blow the arsenic becomes stationary at 0.06 per cent., whereas in the third blow it does not become stationary until it has fallen to 0.034 per cent. The abrupt ending of the removal of arsenic is more likely to find its explanation in the composition of the slag, and it is to be hoped that Mr. Mathewson will supplement these extremely valuable data with others in which the composition of the slag at the same time shall be given. The sudden rise of arsenic toward the end of the third blow I suppose must be referred to an error in sampling or analysis.

Jan 1, 1908

By W. Bonfield

The microstrain characteristics of a polycrystal-line Cu 1.9 wt pet Be precipitation-hardening alloy have been determined for various conditions of aging. The friction stress remained constant for all the conditions investigated, whereas the microscopic yield stress (the stress to produce a plastic strain of 2 x 10-8 in. per in.) and the three-stage stress-strain curve in the microstrain region were sensitive to changes in dislocation and precipitate distribution. Correlations between the measurements of microplasticity and electron-nzicroscope observations of substructure are considered. ALTHOUGH the macroscopic mechanical properties of Cu 1.5 to 2.0 wt pet Be precipitation-harden ing alloys were established' in some detail, there has been no previous investigation of the nature of microyield-ing in these alloys. This paper describes a high-sensitivity extensometer determination of microplasticity in polycrystalline Cu 1.9 wt pet Be, in which the friction stress, the microscopic yield stress (the stress to produce a plastic strain of 2 x 10-6 in. per in.), and the rate of strain hardening in the micro-strain region were measured for various conditions of precipitation. The structural changes accompanying aging in this alloy were examined using transmission electron microscopy, a study which differed from previous investigations as, in order to minimize grain boundary precipitation effects,' the solution-treated alloy was cold-rolled to 40 pet reduction prior to aging. Hence the extent of recovery and recrystalliza-tion, as well as the variation of precipitate morphology and distribution, were assessed. From these results possible correlations between the microstrain characteristics and the observed precipitate and dislocation structure are considered. EXPERIMENTAL PROCEDURE The material investigated was a commercial copper beryllium alloy (Berylco 25), which had a com- position of 1.9 wt pet Be and 0.2 wt pet Co. The alloy was solution-treated at 800°C, quenched in water, and then cold-rolled to 40 pct reduction. Tensile specimens of gage length 1 in. and rectangular cross section of 0.18 by 0.06 in. were prepared from the solution-treated, cold-rolled material and aged for 15 min, 2, 24, and 100 hr at 315°C and 24 hr at 425°C to produce a range of precipitate structure. The hardness values associated with these conditions are listed in Table I. It can be seen that a maximum value is obtained after 2 hr at 315oC, which decreases with continued time at temperature to a minimum after 24 hr at 425°C. For comparison some as-solution-treated specimens were also aged for 2 hr at 315°C. The specimens heat-treated to a given condition were examined in two ways. First, the nature and distribution of the precipitate and dislocation structure was characterized using transmission electron microscopy. Thin foils were obtained from the specimens by electrolytic polishing in a 30 pet nitric acid-alcohol solution at -20oC, and were examined in an RCA EMU 3 electron microscope. Second, the mi-croplastic behavior of the specimens was measured with a Tuckerman strain gage, using the load-unload technique previously described2, 3 to determine the friction stress, the microscopic yield stress, and the variation of plastic microstrain with stress. RESULTS 1) Structural Changes During Aging. a) Annealing Processes. The solution-treated, cold-rolled Cu 1.9 wt pet Be had an irregular dislocation-cell structure,

Jan 1, 1968

By Rossiter W. Raymond

The term " pipe-vein " has recently been applied in this country to certain deposits of lead ore in magnesian limestone. The use of the term has been twofold. It has been revived as a term found in textbooks on mineral veins, with the implied or declared assertion that the ore-deposits thus named in this country are similar to those which have borne the title abroad. It has also been advanced as an appropriate name for a new class of deposits, even if such a class had not previously been recognized. In either case, the assumption is that pipe-veins form a group or class by themselves, and are not merely interior and subordinate features in larger deposits. The peculiar mining law of the United States, which regards " the vein," whatever that may be, as the basis of title, lends a special interest to these claims. But the object of this paper is rather to discuss the subject from the standpoint of geology and technical literature. I shall briefly answer two questions: (1) What are pipe-veins as described in technical literature? and (2) Is the name appropriate or necessary for a new class of deposits ? The term " pipe-ore," as applied, for instance, to irregular, cylin-

Jan 1, 1879

By Rossiter W. Raymond

(Read at the Amenia Meeting, October, 1877.) THE term "pipe-vein" has recently been applied in this country to certain deposits of lead ore in magnesian limestone. The use of the term has been twofold. It has been revived as a term found in textbooks on mineral veins, with the implied or declared assertion that the ore-deposits thus named in this country are similar to those which have borne the title abroad. It has also been advanced as an appropriate name for a new class of deposits, even if such a class had not previously been recognized. In either case, the assumption is that pipe-veins form a group or class by themselves, and are not merely interior and subordinate features in larger deposits. The peculiar mining law of the United States, which regards " the vein," whatever that may be, as the basis of title, lends a special interest to these claims. But the object of this paper is rather to discuss the subject from the standpoint of geology and technical literature. I shall briefly answer two questions : (1) What are pipe-veins as described in technical literature? and (2) Is the name appropriate or necessary for a new class of deposits ? The term "pipe-ore," as applied, for instance, to irregular, cylin-

Jan 1, 1878

By Georges Fleming

The new burden preparation plant of ARBED Luxembourg, Belval- Works, which comprises 2 large sinter strands, is equipped with a process computer connected to a comprehensive process control system. The main jobs done by the computer are the control of the raw mix composition, and thus the monitoring of the stacking of the piles at the bed-blending plant, and the optimization of the sintering process. Among the optimization criteria, quality is considered as the most important. The sinter quality, characterized by the mechanical strength and the state of oxidation, is controlled automatically. The control system which we have dev loped is highly reliable; as a result, the standard deviation of Fe++, for the control of bivalent iron, has been narrowed to 0,5 % and the standard deviation of the IS0 + 6, 3 mm index, for the control of the mechanical strength, has been kept within 1 %. Thanks to these results, the combined savings in fuel consumption at the sinter plant and at the blast furnaces have covered the total costs of the optimization project in 2 years. By applying automatic control, the optimum driving range of the sinter plant has been defined and these new guidelines are used for monitoring the sinter production.

Jan 1, 1977

By T. L. Joseph

IN connection with its investigations of the blast'-furnace process, the Bureau of Mines, in coöperation with the Minnesota School of Mines Experiment Station, developed a 6-ton experimental furnace. Such a furnace was needed to determine the feasibility of producing ferromanganese from Minnesota manganiferous iron ores, a problem of national importance because of the present need for manganese in the steel industry and our small reserves of ferro-grade ores. Furnace operators are reluctant to use new or untried raw materials or to make decided innovations in practice on account of the financial hazard of experimenting with full-scale equipment. A small furnace which can be operated at a relatively low cost is particularly adapted for testing new, raw materials and for determining the feasibility of decided innovations in practice. Laboratory experiments, plus whatever information may be available, are valuable but often do not indicate the net result of changes in an operation involving a large number of interrelated variables. From time to time the coöperation of the Bureau of Mines is solicited in connection with problems involving departures from normal procedure. Under these circumstances some sort of a practical demonstration is a desirable forerunner to full-scale operations which appear feasible after small-scale tests.

Jan 1, 1928

By Hugh D. Pallister, Richard W. Smith

The Alabama flake-graphite industry has flourished only in times of war when importations of foreign graphite for crucible use have been greatly curtailed or cut off. World War I was a boom period and in 1918 some 30 plants produced 7,795,475 lb. of flake graphite. The industry languished following the war and no graphite was produced from 1929 to 1939. The Federal Bureau of Mines began investigating the Alabama graphite deposits in 1940 and worked out modern recovery methods that were applied to production during part of World War II. A prospecting program disclosed reserves of over 25 million tons of graphitic schists. In 1942 the War Production Board authorized the enlargement of the only plant then producing flake graphite and the construction of two new plants. Production of flake graphite from these three plants in 1943 is estimated at 8,100,000 lb. Increased imports from Madagascar late in 1943 shut down one of the new plants and curtailed production at the other. Alabama flake graphite has not yet been able to compete with Madagascar graphite for use in the manufacture of any but small graphite crucibles. The future of the industry must depend on meeting the higher carbon content demanded for other uses.

Jan 1, 1945

Suggestions for Directorial representatives should be submitted by the District Committees between November 1 of the year indicated and the following Annual Meeting District 1 New York Section (Each Year) District 2 Boston (1950) Pennsylvania Anthracite (1951) Lehigh Valley (1952) Philadelphia (1953) Connecticut (1954) Adirondack (1955)

Jan 1, 1952

By S. Jana, C. M. Wayman

The reverse transformation of bcc martensite to the fcc phase was studied in an Fe-33.95 wl pct Ni alloy by nzeans oj dilatometry, melallography, and electron microscopy. Upon "slozc" heating (-1°C per min) length cJmnge us temperature plots showed u gradual contracLion over the temperature range 200" to 280"C ,followed by a more abrupt contraction beginning a1 -280°C. Howet,ev, zchen the heating rate was increased -4°C per tnin, no gradual contraction was observed and only the abrupt contraction starting at -2BO"C was found. Thus on slower heating- the AS "temperature" for the subject alloy, unlike the MS temperature, is better defined as a range of temperatures. Both optical and transmissiorl electron microscope observations showed that some of the martensite plates exizibited a partial loss of transformation twins during reversal. The midvib region of the martensite plates disappeaved relatively early duirng the reversal. Metallographic observations slowed that the earliest detectable stage of the rezlerse tvansforrvration begins (axd Moues inulardly) at The Martensens i te - parent interface. At higher temperatirres, the. formation of martensitically reversed jcc plates within the bcc martensite plales was observed. It is concluded that the reverse transformation consists of a diffusion less process (martensitic); but this is ps-obably aided by a prior or simultaneous dijjusiorz-comltvolled process, at leasl in the case of slower heat-ing' experiments. ALTHOUGH numerous investigations have dealt with the parent-to-martensite ("forward") transformation (fcc — bcc) in Fe-Ni alloys, comparatively little is reported on the ("reverse7') martensite-to-parent transformation.'-4 Even though such reverse transformations have been studied in detail in some nonferrous systems, one of the difficulties of studying the reverse transformation in most ferrous mar-tensites is that the martensite decomposes by tempering during heating. However, carbonless Fe-Ni alloys do not exhibit this difficulty since the transformation in these alloys is completely reversible. The present investigation represents an attempt to shed more light on the nature and mechanism of the martensite-to-parent transformation. 1) EXPERIMENTAL PROCEDURE 1.1) Alloy Prepatation. Fe-Ni alloys of compositions near 34 wt pct Ni were prepared from zone-refined iron (99.994 wt pct Fe) and high-purity nickel (99.999 wt pct Ni) by induction melting in recrystallized alumina crucibles in an argon atmosphere, with prior vacuum evacuation to 10"3 mm Hg. The alloys were homogenized by induction stirring in the molten state for 5 min. After solidification, the alloys were further homogenized in evacuated quartz capsules for 96 hr at 1230°C. 1.2) Dilatometry. Slices of the ingot were hot-forged (750°C in air) into approximate rod form and these specimens were then hot-swaged (750°C in air) into long cylindrical rods 0.55 mm diam. From the rods, specimens about 1 in. long were cut. These were then vacuum-annealed for 24 hr at 1200°C, cooled to room temperature, and subsequently transformed to martensite in liquid nitrogen (whereby about 40 pct transformation was obtained). Dilatation measurements were made by observing length changes in a vacuum dilatometer with an externally mounted LVDT sensing element. 1. 3) Preparation of Electron Microscope Specimens. Slices of the ingots were cold-rolled (with intermediate vacuum anneals) to -0.020 in. Out of these rolled sheets, specimens (about 1 by 1 in.) were cut. These were then vacuum-annealed, transformed to martensite by cooling in liquid nitrogen, and subsequently heated from room temperature to various temperatures to effect either partial or complete reverse transformation. These specimens were then chemically polished to 0.002 in. in l:l HsOz (30 pct) and &PO4 (85 pct) solution, and thinned to electron transparency in an electrolyte consisting of 150 g CraOs, 750 ml glacial acetic acid, and 30 ml ~~0.~ Observations were made with a 100-kv Hitachi HU-11 electron microscope equipped with an HK-2A tilting device. 1.4) Optical Microscopy. Metallographic observations were made with a Leitz MM5 metallograph on the same 0.020-in. sheet specimens as were used for electron microscopy and on bulk specimens which were 0.2 in. or more on a side. The chemical thinning solution when cooled below 20°C also served as an etchant for this alloy. Observations of surface relief were made with a Zeiss interference microscope employing a Thallium light source of wavelength 0.54 p. Specimens for interference studies were prepared by two-stage polishing on Buehler vibromet polishers using 0.3 and 0.05 p alumina abrasives. 2) EXPERIMENTAL RESULTS 2.1) Comparison of the MS,AS, and Af Tempera-tures wTth Previous Re sults. The AS aLd Af tempera -tures of several Fe-Ni alloys were determined dila-tometrically. The MS temperatures of the same alloys were determined by continuously lowering the temperature using a mixture of isopentane and liquid nitrogen and observing the highest temperature at which a prepolished specimen showed surface upheavals. For the present the As temperature is defined as the temperature at which an abrupt decrease in length occurs in the dilatation plot. The Ms,As7 and A determinations in the present investigation and those of Kaufman

Jan 1, 1968

By P. E. Landolt

MILITARY necessities and economic scarcities, occasioned by the first and second World Wars, led to the search for substitute materials and new products to meet the demands of advancing technology accelerated by research development. Among others, lithium came to attention. Its chemistry had been studied for a long period, but its general use was quite restricted due to limited known sources of raw material. In World War I, Germany used lithium metallurgically for two principal purposes: 1-hardened lead alloy, B-Metal, for railway bearings as a substitute for lead-tin-antimony alloys; and 2-light strong aluminum alloys, Scleron, in which zinc was largely substituted for copper.

Jan 12, 1951

By J. J. Gilman

Zinc monocrystals, when compressed nearly parallel to their basal planes (within 20), deform in a new way; and certain deformation markings, called "-bands," are typical of this new mode. Characteristics of these bands are described. Mechanical behavior of low angle zinc monocrystals was investigated in some detail. Recrystallization did not occur upon annealing of banded specimens that were free of deformation twins. -Bands do not seem to be the result of nonbasal slip, but rather, a result of a microbuckling mechanism. u-Bands differ qualitatively and quantitatively from ortho kink bands. A dislocation model, consistent with some of the features of u-bands, is described. THE plastic deformation of zinc monocrystals with slip planes (0001) nearly parallel to the stress axis was studied in this investigation. In a previous investigation, it was shown that some low angle zinc crystals (those with slip planes making angles of more than about 2.5+1° with the compression axis), deform by ortho kinking while others (those with slip planes making angles of less than 2.5+1° with the compression axis) deform in a new way.' This new mode of deformation will be described in some detail here. Some of its striking features are: 1—it operates only for compressive stresses, 2—its temperature dependence is anomalous, and 3—it exhibits a new type of "yield-point" behavior. The mode of deformation to be discussed is not new in the sense that no previous evidence of its existence had been reported. The markings that it creates on the cleavage surfaces of zinc crystals have been described by several investigators.'" However, this is the first time that it has been made to operate under controlled conditions so that its response to mechanical variables, temperature, and aging treatments could be investigated and its geometry completely described. Apparently. Jillson' as well as Holden3 and Pratt" believed that the small bands they observed were simply small versions of ortho kink bands. In fact, two of these authors3,6 "alled the markings "micro kink bands." In spite of the precedence, it is felt that this term is not entirely suitable because these bands do not have the same genesis as kink bands, and they are qualitatively different in structure. As will be indicated by later discussion, the bands seem to be related to the tensile deformation bands observed in aluminum. The present author has chosen to call the bands "micro deformation bands," or simply ",ubands," and the deformation process, ''p-banding." Experimental Methods Crystals were grown from 99.999+ pct Zn obtained from the New Jersey Zinc Co. The details of the technique are given elsewhere." It should suffice to say that the crystals were seeded for orientation control, and precision pyrex tubes were used for molding them. About 40 crystals were used, yielding some 130 specimens. Fig. 1 illustrates the typical form of the specimens and shows how the orientation angles are defined. The crystal specimens were usually 1 3/4 in. long and about 150 mil in diameter. The angle between the slip or cleavage plane (0001) and the specimen axis is designated by xo, while a is the angle between the maximum slope of the (0001) plane and the nearest close-packed direction [1210], vary ing from 0°to 30°. The crystals were cut into specimens with a jeweler's saw and the ends were squared by filing (specimens held in V-block). Crystals of this orientation are stiff toward bending, so this procedure introduced only deformation localized at the ends. Then the specimens were polished either chemically in 50 pct HNO³ or electrolytically in 20 pct chromic acid. The mechanical tests were made with an Instron testing machine. This machine weighs by means of electric strain gages on elastic bars and is quite stiff, since the full-load deflection of its load cells is at most 0.002 in. Most of the testing was done at a

Jan 1, 1956

President-Mrs Felix E Wormser, 1 Acorn Lane, Larchmont, New Yolk First Vice-President-Mrs Francis Cameron, 10 Edgewood Drive, Summit, New Jersey Second Vice-President-Mrs Lyman H Hart, 67 Essex House, Garthwood Apartments, Scarsdale, New York Third Vice-President-Mrs David Eugene Park, 350 East 57 Street, New York 22, New York Fourth Vice-President-Mrs Harold 0 Bosworth, 415 Lafayette Street, Denver 3, Colorado Fifth Vice-President-Mrs J B Haffner, Box 29, Kellogg, Idaho Recording Secretary-Mrs W McG Peirce, 7 Lexington Avenue, New York 10, New York Asst Recording Secretary-Mrs Arnold H Miller, 601 West 115 Street, New York 25, New York Corresponding Secretary-Mrs Theodore Nagel, 76 Remsen Street, Brooklyn 1, New York Treasurer-Mrs Robert W Rowen, 116 East 68 Street, New York 21, New York Assistant Treasurer-Mrs Samuel Dolbear, 11 Broadway, New York 4, New York Assistant Treasurer-Mrs H A Kursell, 12 Murray Hill Road, Scarsdale, New York

Jan 1, 1954

By H. W. McCue

In 1945 the number of oil wells drilled was less than in 1944 but the number of gas wells was greater. The oil wells numbered 176, completed for an initial production of 25,214 bbl., an average of 143 bbl. per well as against a total in 1944 of 245 drilled for 32,886 bbl., or 134 bbl. per well. All of these wells were in proven areas and no new discoveries

Jan 1, 1946