Search Documents

By Ole Singstad

THE legislatures of New York and New Jersey, determined in 1919 that a vehicular tunnel should be built under the Hudson River. On July 1, 1919, an engineering staff was organized with the late Clifford M. Holland as chief engineer, and this staff was given a number of problems to solve, such as location, size, type of tunnel, method of construction, method of ventilation and cost. After a period of preliminary investigations and studies it was decided to build the tunnel at Canal St., New York, connecting 12th St., Jersey City. This is the center of the heaviest traffic across the Hudson River. It was also decided to build two tunnels-one for west-bound traffic and one for east-bound traffic-the tunnels to be of cast iron, built up of segments and bolted together, each tunnel to have a roadway 20 ft. wide and a clear heat room of 13 ft., 6 in. This is to provide for two lines of vehicles in each direction. The tunnels have an exterior diameter of 29 ft., 6 in. The interior lining is of concrete, the sidewalls tiled with a vitreous white tile and the roadways paved with granite block. The entrances and exits at both ends are separated by two blocks so as to reduce traffic congestion. BASIS OF VENTILATION It was recognized very early that one of the most important problems confronting the engineers was a proper ventilation system. It was estimated that each tunnel as planned would have a traffic capacity of 1900 vehicles per hr. The tunnels are 8500 ft. long between portals, and it was considered that the ventilation should be based on all of these vehicles being operated by gasoline engines. That presented a problem in ventilation unlike any other either in magnitude or character.

Jan 8, 1926

By R. S. Goodrich, G. S. Ansell

The microstructure of three Al-Al2O3 SAP-Type alloys (containing 2.0, 3.0, and 5.7 wt pct alumina, respectively) was studied utilizing transmission electron microscopy. These alloys were fabricated from aluminum powders by powder-metallurgical techniques, cold-rolled into thin strips, and recrys -tallized. Thin foils suitable for an electron-transmission study were then prepared from the strip material by electropolishing. The microstructure of these alloys is shown to consist of small (0.1 mean diameter) plate -shaped alumina particles finely distributed in an aluminum matrix. In the higher-oxide content alloys the platelets are somewhat larger and more irregular in shape. The distribution of oxide particles is not uniform and there is an increasing tendency toward clumping SINCE the discovery by Irmann1 that aluminum alloys produced by compacting, hot pressing, and extruding fine aluminum powders possess remarkable high-temperature mechanical properties, the Al-A12O3 SAP-Type alloys have been utilized extensively as model dispersion-strengthened alloys in both experimental and theoretical invest igations.2-8 The use of the SAP-Type alloys as model dispersion-strengthened alloys implicitly assumes that their microstructure has been completely delineated. This is, however, not the case. with increasing oxide content. In all the alloys studied, the mean center-to-center spacing of particles was quite small (0.2 u) due to the very fine oxide debris present. Selected-area diffraction of the specimen identified the oxide as either y Al2O3 or y' Al2o3. The re crystallized MD-5100 alloy exhibited a mean grain diameter of only 0.7u, while the grain size of the other alloys was several hundred microns. Severe pinning of the grain boundaries by oxide particles was rarely observed, and the grain boundary triple points in the small-grained MD-5100 alloy were often particle -free. Diffraction contrasts visible around the particles are attributed to elastic strain fields set up by differential thermal contraction during cooling from the recrystallization anneal. Early investigation demonstrated that optical metallography did not possess sufficient resolution to observe the microstructure of the SAP-Type alloys.' Later, extensive use was made of replication techniques to study the microstructure by means of electron microscopy.7-9 These studies indicated that the SAP-Type alloys consist of a dispertion of irregular Al2O3 platelets, approximately 150A thick 9 and a micron or so on edge,9 distributed in a matrix of commercial-purity aluminum. These oxide platelets tend to be oriented in the aluminum matrix, with their largest dimension parallel to the extrusion direction. 8,9 A study employing polarized-light techniques1' indicated that the grain size of a series of as-extruded SAP-Type alloys was several microns in diameter, while the grain size after re-crystallization was several millimeters in diameter. A more recent study 12 utilizing surface-replication techniques examined the particle morphology,

Jan 1, 1964

By J. E. Burke, C. S. Barrett

The fine lines shown in Fig I are typical of markings that ma): be detected after polishing and etching deformed specimens of alpha brass and other alloys. Although they have long been the subject of discussion by metallurgists their nature is still uncertain and the names that have been applied: to them, such as deformation line4 or strain markinas, indicate this uncertainky. In this paper which repotts the results of a furthcr investigatinn of their nature, they will be called strain mxrkings. Introduction Mathewson and Phillips1 described strain markinps in 1 916 and concluded that they appear only after 20 pet deformation. They objected to the markings being called slip tines believing this term should be sewrved for surface markings protluced by plastic deformntion. In 1921. vogel² described similar striations which appeared after polishing and etching the roughly ground surface of numerous alloys. He reported that the markings were crystallo-graphic in nature, and since they resemble Seumann hands in iron, at least superficially, he assumed them to be mechanical twins. In 1928, Matherwson reported work by Phillips which indicated that the lines were more readily produced by impact than by slow deformation and that in many cases the twins inside recrystallized grains were parallel to strain markings in the original deformed grains. This was taken as cvirlence that the markings coalesce into anncaling twins. and hence that they themselves are mechanical twins. Many attempts have been made to demonstrate directly that the markings are mechanical twins. In 1934, Samans described the results of X ray studies of two defomed crystals of alpha brass. Evidence was obtained which could be interpreted to indicate that the strain markings arc mechanical twins, and this remains the only direct evidence to this effect. Several other attempts to obtain similar evidence by X ray diffraction have failed5.8.7 although in no Ease was the original method of Samans employed. An

Jan 1, 1949

By C. S. Barrett, J. E. Burke

The fine lines shown in Fig I are typical of markings that ma): be detected after polishing and etching deformed specimens of alpha brass and other alloys. Although they have long been the subject of discussion by metallurgists their nature is still uncertain and the names that have been applied: to them, such as deformation line4 or strain markinas, indicate this uncertainky. In this paper which repotts the results of a furthcr investigatinn of their nature, they will be called strain mxrkings. Introduction Mathewson and Phillips1 described strain markinps in 1 916 and concluded that they appear only after 20 pet deformation. They objected to the markings being called slip tines believing this term should be sewrved for surface markings protluced by plastic deformntion. In 1921. vogel² described similar striations which appeared after polishing and etching the roughly ground surface of numerous alloys. He reported that the markings were crystallo-graphic in nature, and since they resemble Seumann hands in iron, at least superficially, he assumed them to be mechanical twins. In 1928, Matherwson reported work by Phillips which indicated that the lines were more readily produced by impact than by slow deformation and that in many cases the twins inside recrystallized grains were parallel to strain markings in the original deformed grains. This was taken as cvirlence that the markings coalesce into anncaling twins. and hence that they themselves are mechanical twins. Many attempts have been made to demonstrate directly that the markings are mechanical twins. In 1934, Samans described the results of X ray studies of two defomed crystals of alpha brass. Evidence was obtained which could be interpreted to indicate that the strain markings arc mechanical twins, and this remains the only direct evidence to this effect. Several other attempts to obtain similar evidence by X ray diffraction have failed5.8.7 although in no Ease was the original method of Samans employed. An

Jan 1, 1949

By J. H. Craig

As a result of information that the Navy Department was questioning the advisability of raising the maximum allowable exposure temperature for zinc-coated steel parts from 500 to 750 F., it was decided to make a series of high temperature tension tests on several types of uncoated and zinc-coated steels. The objective was to determine at what temperature intergranular penetration of galvanized steel by zinc might take place under conditions of rapidly applied stress and temperature. Tests were conducted in the range from room temperature to 1400 F. In this range, low-carbon and high-carbon steels did not suffer any adverse effects due to zinc coatings. In fact, at 1400 F. the zinc coatings appeared to have a beneficial effect. In stainless steel, the coating had no effect up to 1000 F. Above this temperature, the zinc coating appeared to cause a marked loss in ductility and a less pronounced loss in strength. There was no visible evidence of zinc penetration of the stainless steel structure, but it was assumed that this was the cause of the adverse effect.

Jan 1, 1945

DESPITE strikes, domestic production of copper and zinc in 1951 rose about 3 pct and 10 pct, respectively. Lead output fell only about 7 pct. Primary refined, including processed scrap and imported concentrates, was somewhat higher for zinc, and slightly lower for copper and lead. Prospects are for moderately larger mine and refined production in 1952 according to Standard & Poor's analysis of nonferrous metals. The survey goes on to report domestic copper prices averaged 14 pct higher in 1951, lead prices 30 pct higher, and zinc prices 32 pct higher. The 2¢ rise in zinc and lead ceilings in October will lift the average price in 1952 over 8 pet, assuming no further price change. Currently, OPS appears opposed to raising the 24 ½ ¢ copper ceiling to the 24 ½ ¢ maximum on imported metal. The steep premiums in world markets are likely to be reduced in 1952. Sales in 1951 were at new peaks. A further moderate rise is indicated for 1952. Earnings of the industry were at a new high in 1951. The increase for companies covered in the survey was perhaps 25 pet, despite a tax rate of about 53 pet, against about 40 pct. in 1950. Relatively maintained to moderately higher earnings are currently indicated for 1952. About two thirds of the companies covered in the survey raised dividends, including extras, in 1951. In general, maintained payments appear probable in 1952.

Jan 1, 1952

By G. E. Pralle

INTRODUCTION The decade from 1969 to 1979 saw the crest of a wave of investments by companies and investors, primarily from the major industrial nations, in the metals and minerals industries of the so-called lesser developed countries. This was brought about by two major considerations: 1). The higher ore grades and therefore the higher profit potential of the mineral deposits in the third world countries, and 2). The desire, particularly by the European countries and by Japan, to ensure a safe supply of raw materials not available in their own countries. The decade began with the start of the Toquepala mine in Peru and the major investments in the Bougainville mine in Papua New Guinea and the Ertsberg mine in Indonesia. It ended with the start-up of Southern Peru Copper Company (SPCC) Cuajone mine in Peru and Inco's Soroako mine in Indonesia and the investments in several major alumina or aluminum projects in Australia and Brazil. Concurrent with this huge flow of funds into the mineral resources industry of the developing world was the build-up of a psychological fear in the host countries of exploitation/domination by the foreign investors. This resulted in an increasing trend towards: 1). Nationalization of existing mineral ventures, and 2). Tougher legal/fiscal frameworks for new ones. NATIONALIZATION Nationalization appeared in its earliest form as "Mexicanization" of the petroleum industry in Mexico in the 1930's, followed later by Mexicanization of the mining industry in general. This was enacted with the Mexican Mining Law of 1961 which required that 51% of the equity be owned by Mexican nationals. Later in the decade the equity share for foreign investors was reduced to 33 1/3% for the developers of the Frasch sulphur operations in the Isthumus of Tehuantepec. However, the law was not fully implemented in the copper industry until late 1970 with the purchase of 51% of the ownership in the Cananea Mining Company. The trend toward nationalization of the copper industry progressed to Chile where in 1967 under the Government of Eduardo Frei the major North American copper companies were induced to sell a one-half interest in their Chilean mines to the State. Likewise, in 1970, "Zambianization" took place, when the two major operating companies Roan Selection Trust (Amax) and Zamanglo (Anglo American) were restructured into Roan Consolidated Mines (RCM) and Nchanga Consolidated Mines (NCCM) providing the government with 51% of the equity ownership. Whilst the earlier forms of nationalization in general constituted a fairly priced buy-out (El Teniente, Chile for US$80 million, RCM for US$117.8 million, NCCM for US$178.7 million), the total nationalization of the Chilean mining companies in 1970 under Salvador Allende did not. Later, "Western" countries joined this trend and on October 29, 1973, Mr. Gough Whitlam proclaimed that "overseas capital must continue... in partnership with Australian capital" and "in some special energy cases we have an objective of 100% Australian ownership". In 1974 Mr. Pierre Trudeau stated: "The Liberal Party of Canada sets as an objective that new resources projects in the natural resource field should have at least 50% and preferably 60% Canadian equity ownership". FOREIGN INVESTMENT The situation for the foreign investor in the worldwide resource industry rapidly deteriorated from then on. New features appeared in mineral exploitation and operating agreements, centering not only on local government/local companies ownership but also on increased taxation. The new tax rate (mineral tax, royalty, and income tax) for the semi-government companies NCCM and RCM in Zambia became an effective 73%. Likewise the much publicized and discussed renegotiated Bougainville agreement brought dramatic increases in the total "take" by the PNG Government. More innovative forms of indirect taxation made their appearance and were added to the normal tax burdens of the mineral industry which already

Jan 1, 1985

By W. S. Potter

THE proportions of manganese and carbon in manganese steel are familiar to all, because manganese-steel castings have been well known for a decade or more in this country. The same alloy has now become a commercial product in the wrought state, and, as not only rails and bars are rolled daily but a great variety of forged and otherwise fabricated shapes are appearing, it may be interesting to mark the progress and, perhaps, to look a little closely into the nature of this important material of engineering.

Jan 4, 1914

As reported in Drift last month demolition of old buildings on the 47th St. site has been completed, and detailed plans and studies for the new structure are well underway. As this issue was being sent to press the $5 million industry- business phase of the fund campaign had passed the half- way mark toward its goal. Target date for the building program is 1960.

Jan 5, 1958

By H. Shaw

Gravitational measurements made by means of the Eotvos torsion balance over any area enable a representation to be obtained of the total gravitational effects over the surface of that area arising from the combination of all sources of gravitational disturbance. The investigation of gravitational anomalies occurring in the upper layers of the earth's crust, in this way, has been attended with considerable success, and, especially in areas in which no undesirable disturbing factors were present, it has been possible to locate geological structures and mineral deposits with remarkable accuracy and also to delineate their confines and to indicate their depth below the surface with a certain amount of precision. Before this can be done successfully, however, it is necessary to determine the gravitational effect arising from all other extraneous anomalies in order that these may be satisfactorily eliminated. Disturbing features giving rise to these gravitational anomalies may be divided into two classes, according to whether they are situated at or below the surface. The former are determined readily by a detailed leveling of the ground surface, and may be satisfactorily eliminated provided the specific gravity of the terrain material is known, but the latter are generally unknown, and can only be ascertained with difficulty. When, therefore, the observations obtained by means of the Eotvos torsion balance have been corrected for all surface irregularities, known as terrain and topographical effects, there remain residual gravitational values which are due entirely to subterranean conditions. The. task of interpreting these results consists in disentangling the various subsurface anomalies, and subsequently in computing and recombining the effects of these various masses in order to verify the interpretation. When the gravitational anomalies are due to large and comparatively simple structures it is a matter of little difficulty to arrive at a satisfactory interpretation of the subterranean conditions, but in more complex areas, where the geological conditions are more complicated and several irregular features exist, the process of disentangling the various constituents of the complex mass arrangement is more difficult and requires the expenditure of considerable time and labor. When the subterranean effects have been obtained, they are subjected to a critical examination, and an effort is made to recognize and

Jan 1, 1932

By Dwight M. Lemmon

Encouraged by increased demand and higher prices for such metals as copper, lead, zinc, silver and tin, search was pressed in 1964 for mineral raw materials, especially in parts of the world that are relatively more stable politically and economically. New discoveries of metallic ores continued to be made, discoveries based on extensive geologic and geophysical work but nonetheless made in part because of good fortune.

Jan 2, 1965

By Herbert Clark Hoover, Lou Henry Hoover

IN the last book I have explained the methods of delimiting- the meers along each kind of vein, and the duties of mine officials. In this book1 I will in like manner explain the principles of underground mining and the art of surveying. First then, I will proceed to deal with those matters which pertain to the former heading, since both the subject and methodical arrangement require it. And so I will describe first of all the digging of shafts, tunnels, and drifts on venae profundae; next I will discuss the good indications shown by canales2, by the materials which are dug out, and by the rocks ; then I will speak of the tools by which veins and rocks are broken down and excavated ; the method by which fire shatters the hard veins ; and further, of the machines with which water is drawn from the shafts and air is forced into deep shafts and long tunnels, for digging is impeded by the inrush of the former or the failure of the latter ; next I will deal with the two kinds of shafts, and with the making of them and of tunnels ; and finally, I will describe the method of mining venae dilatatae, venae cumulatae, and stringers.

Jan 1, 1950

By George D. Dub

Owens Lake is at present a source of important nonmetallic minerals, sodium carbonate (soda ash, Na2CO3); sodium sesquicarbonate (trona, Na2CO3.NaHCO3.-2H2O) and borax, (Na2B4O7.10H2O). Owens Lake is a closed basin in the southern part of Inyo County, California, at the southern end of Owens Valley, east of the Sierra Nevada Mountains and west of the Coso and Inyo Mountains. Broadly considered, it is in the Great Basin area, but at no time was it a part of Lake Lahontan. Closed Basins Closed basins are phenomena of arid or semiarid regions where outflow is considerably less than inflow and where accordingly soluble salts concentrate in residual liquid. When inflowing waters originate in areas where the rocks are predominantly marine sediments, the residual basin liquid is primarily a chloride, brine; if the rocks are largely igneous, the residual brine tends to be alkaline containing carbonates, and sometimes borates as well. Since normally, both types of rocks occur in regions contiguous to closed basins, residual liquids do not often fit into the two broad divisions mentioned. No two residual brines are exactly alike, just as no two ore deposits are exactly alike. Even out of the same closed basin, it is possible to get widely different analyses of liquids since underground and surface flows, as well as local evaporation rates and other conditions might have a marked influence on residual-liquid compositions. At Searles Lake, The American Potash and Chemical Corporation is building a plant to process a lower-level brine which is considerably higher in sodium carbonate and borax, and lower in potassium chloride, than that company has processed for many years. F. W. Clarke1 has classified waters of closed basins as follows: I. Chloride type; largely sodium chloride (NaC1) and of oceanic type, such as Great Salt Lake. Related is -the Dead Sea, a bittern residue of magnesium, potassium and sodium chlorides. a. Sulphate type; largely sodium sulphate (Na2SO4) with considerable sodium chloride such as Sevier Lake, Utah; Laramie Lakes, Wyoming; Dale Lake, California. 3. Carbonate type; high in carbonates and fairly high in sulphates, such as Moses Lake, Eastern Washington; and the Nebraska Potash Lakes. 4. Carbonate—chloride type; lower in carbonates than type 3 and about equally rich in sulphates, such as Pyramid Lake, Nevada. 5. Sulphate—Carbonate type; quite high in sulphates and carbonates, such as Pelican Lake, Oregon. 6. Triple type; considerable quantities of carbonates, sulphates and chlorides

Jan 1, 1948

By George D. Dub

Owens Lake is at present a source of important nonmetallic minerals, sodium carbonate (soda ash, Na2CO3); sodium sesquicarbonate (trona, Na2CO3.NaHCO3.-2H2O) and borax, (Na2B4O7.10H2O). Owens Lake is a closed basin in the southern part of Inyo County, California, at the southern end of Owens Valley, east of the Sierra Nevada Mountains and west of the Coso and Inyo Mountains. Broadly considered, it is in the Great Basin area, but at no time was it a part of Lake Lahontan. Closed Basins Closed basins are phenomena of arid or semiarid regions where outflow is considerably less than inflow and where accordingly soluble salts concentrate in residual liquid. When inflowing waters originate in areas where the rocks are predominantly marine sediments, the residual basin liquid is primarily a chloride, brine; if the rocks are largely igneous, the residual brine tends to be alkaline containing carbonates, and sometimes borates as well. Since normally, both types of rocks occur in regions contiguous to closed basins, residual liquids do not often fit into the two broad divisions mentioned. No two residual brines are exactly alike, just as no two ore deposits are exactly alike. Even out of the same closed basin, it is possible to get widely different analyses of liquids since underground and surface flows, as well as local evaporation rates and other conditions might have a marked influence on residual-liquid compositions. At Searles Lake, The American Potash and Chemical Corporation is building a plant to process a lower-level brine which is considerably higher in sodium carbonate and borax, and lower in potassium chloride, than that company has processed for many years. F. W. Clarke1 has classified waters of closed basins as follows: I. Chloride type; largely sodium chloride (NaC1) and of oceanic type, such as Great Salt Lake. Related is -the Dead Sea, a bittern residue of magnesium, potassium and sodium chlorides. a. Sulphate type; largely sodium sulphate (Na2SO4) with considerable sodium chloride such as Sevier Lake, Utah; Laramie Lakes, Wyoming; Dale Lake, California. 3. Carbonate type; high in carbonates and fairly high in sulphates, such as Moses Lake, Eastern Washington; and the Nebraska Potash Lakes. 4. Carbonate—chloride type; lower in carbonates than type 3 and about equally rich in sulphates, such as Pyramid Lake, Nevada. 5. Sulphate—Carbonate type; quite high in sulphates and carbonates, such as Pelican Lake, Oregon. 6. Triple type; considerable quantities of carbonates, sulphates and chlorides

Jan 1, 1948

By Albert G. Zima

According to recently puhlished statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed. Today, however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet. Drill Tools Modern rotary drilling tools are the product of ingenious design and careful selection and adaptation of materials used in their construction. They must withstand terrific abrasion and, because of their compactness, must be designed to resist exceedingly high unit stresses. In bits, core drills and reamers, the bodies are made of either forged or cast alloy steels, heat-treated to develop a combination of high strength and toughness. To provide sufficient strength to the threaded portions and to protect the threads from distortion or damage, the box or pin sections of the tools are hardened to approximately 310 to 330 Brine11 hardness number. Drill and reamer cutters are generally of the movable type; i.e., serrated cones, cylinders or disks, which can readily be replaced when

Jan 1, 1935

By Albert G. Zima

According to recently puhlished statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed. Today, however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet. Drill Tools Modern rotary drilling tools are the product of ingenious design and careful selection and adaptation of materials used in their construction. They must withstand terrific abrasion and, because of their compactness, must be designed to resist exceedingly high unit stresses. In bits, core drills and reamers, the bodies are made of either forged or cast alloy steels, heat-treated to develop a combination of high strength and toughness. To provide sufficient strength to the threaded portions and to protect the threads from distortion or damage, the box or pin sections of the tools are hardened to approximately 310 to 330 Brine11 hardness number. Drill and reamer cutters are generally of the movable type; i.e., serrated cones, cylinders or disks, which can readily be replaced when

Jan 1, 1935

By Herbert Hoover

THE desire of the engineers over the last few years, growing out of their contact with public affairs, that this Institute should take a wider vision than the narrower field of technology and should apply its skill to the development of civic problems which must lay in their foundation on engineering, has led to this discussion today. Some of us in San Francisco, in discussing this question of the relation of the engineers to civic problems, raised the question as to whether or not in this national emergency it was not the duty of the Mining Engineers to bring, forward their combined skill and knowledge and experience to bear upon the problems of the coal industry. This industry, considered as a whole, is one of the worst functioning industries in the United States. It is equipped with capital, with machinery, plants and labor to a peak load at least 20 per cent. above the average necessity. This peak load, therefore, involves the use of probably 100,000 men diverted from other productive industries; it involves an intermittency of employment through its whole personnel that results not only in a long train of human woe, but results also in a higher cost of coal -to the general public. The problem of whether the industry can, by any device, be cured or even partially cured of its intermittency, is solely an engineering problem. It is therefore an apropos problem for this Institute. Your President and myself and others thought that we could best develop this discussion by calling upon men of large experience in the particular branches of the soft coal industry, to bring the facts in front of this general committee, with a view to an exhaustive discussion and perhaps subsequently the appointment of a committee to formulate those facts and such remedies as may be developed into a report that would be of constructive value.

Jan 3, 1920

DEVELOPMENT of a chemical process for the extraction of pure metals from mill concentrates or metal scrap has progressed beyond the pilot plant stage and may prove an important adjunct to present smelting and refining methods if initial commercial operations prove economically successful. Developed by the Chemical Construction Corp., the new process involves the treatment of oxide and sulphide ore concentrates by chemical methods, instead of the usual smelting and refining techniques. Several of the many applications are now scheduled for commercial use. Refiners using the new process will prepare ore concentrates by standard flotation methods, introduce the concentrate as a slurry into an autoclave along with water and an acid or ammonia. From the resulting leach solution, recovery of individual metals is made by use of suitable reducing agents. By varying conditions during treatment, different metals in the ore are produced separately as pure powders, which may be pressed into forms ready to market, or in the case of copper, extruded as rods or pipe. The reagents are generally recovered. By manipulating the variables during reduction, selective separation of nickel, and/or cobalt, and/or copper can be made simultaneously. The separation is a continuous operation. Low metal prices are not immediately in view because of the tremendous demand at this time. However, reduced metallurgical treatment costs will allow economical mining of orebodies with lower metal content, permitting increased production to meet demand. Although the practical horizon for use of the new process appears to be limitless, one factor may enter into its employment. Just how low grade a concentrate can be economically used is unknown. In addition, for present practical considerations, only metal below zinc in the electromotive series may be processed. Each commercial application requires specific technique adaptation and pilot-plant data for engineering design. A nickel-cobalt-copper process has been researched and piloted in collaboration with Sherritt Gordon Mines, Ltd., for the firm's Lynn Lake properties. In addition, processes were tailored for cobalt concentrates of Howe Sound Mining Co., and National Lead Co., in view of the urgent need for this specific metal. Major General William N. Porter, president of Chemical Construction, says of the new process, "piloting experience has shown that production cost, from ore concentrates to pure metals should be considerably below current costs." Other savings may be realized by cutting transportation and personnel costs, and by reducing the time lag between mining and pure metal from months to a matter of hours. First commercial use of the process will start sometime this summer. Chemico is slated to finish building a $2.5 million cobalt refinery for Howe Sound Mining near Salt Lake City. The plant is expected to raise world cobalt production by 40 pct. The plant will process 35 tons of 20 pct cobalt concentrates from Howe Sound's Blackbird mine near Cobalt, Idaho, daily. Yearly production is expected to reach 2000 tons of pure metal, about one half of U. S. consumption in 1950. Steps in the Howe Sound application of the process are: 1. Acid oxidation leach. 2. Filtration (residues thrown away are insoluble compounds-gangue, iron, arsenic). 3. Cementation (for Cu removal because Cu content is too low for recovery). 4. Reduction from ammoniacal solution. 5. Separation of Co and Ni as mixed metals (95 pct Co and 5 pct Ni). 6. Recovery of ammonium sulphate. Under construction at the Fredericktown, Mo., mine of National Lead is a $5 million refinery sched- [ ]

Jan 1, 1952

By Elmars Ence, Harold Margolin

The titanium-aluminum system has been investigated in the composition region 0 to 34 pct Al in the temperature range 800" to 1450°C. The phases encountered in this region were: a,ß, TiAl3, The reactions observed are as follows: 13 ; L - 6T. A1, 0 (15 pct Al) + 6 (18 pct Al) - yTi Al (16.5 pct Al) at -1170°C andP (7 pctpct Al) + y (9.2 pet Al) - ah(9 pct Al) at - 1060°C. A eutectoid reaction: y — a +d belm 700°C is postulated. THE Ti-A1 system has been the sub.ect of a number of investigations. Several of these1-3 have indicated extensive solubility of A1 in both a and ß titanium. Ence and Margolin, as a result of work on the Ti-A1-0 system:'5 have shown that the a solubility ofalumi-num is considerably restricted, and found that a compound, Ti2A1 existed in the region formerly designated as Q a This structure was identified as hexagonal with c/a = 0.803. Pietrokowsky confirmed the existence of this phase7 and pointed out that the structure was isomorphous with Ti3Sn.8 Although the existence of Ti,A1 has been confirmed by others,9-12 there has been considerable disagreement regarding the composition and mode of formation. A detailed reinvestigation of the Ti-A1 system has been published by Sagel et al.13 The tentative diagram indicated two phases, a, and e, occurring in the former all a region. The a, phase has the same structure as Ti2A1 and was indicated as having a broad region of solubility. Epsilon, a tetragonal phase, was shown to form within the a, solubility region. AS a result of unpublished work,14 Ence and Mugy3 olin disagreed with the interpretation of Sage1 et al., although some common features existed. The present study was conducted in an attempt to clarify prevailing uncertainties. EXPERIMENTAL PROCEDURE Alloy Preparation—Alloys were prepared from iodide titanium (99.9 pct Ti with less than 0.01 pct Zr) or Bureau of Mines electrolytic titanium (BHN-73) and high purity aluminum (99.99 pct). Alloys were arc-melted in argon or helium atmosphere as 15-g buttons in the composition range up to 34 pct Al. Depending on need, alloys were made in increments varying from 0.25 to 2 pct Al. Up to five 15-g buttons of some compositions were made. Weight losses during melting did not exceed about 1 pct of the charge and chemical analysis revealed that both titanium and aluminum were evaporated. In general, nominal and analyzed compositions agreed within 0.5 pct and therefore nominal compositions were used in plotting the data. Unavoidably, some overlap of composition occurred, particularly where small increments of A1 were used. The small increments were primarily used to obtain alloys which would fall into the narrow a -, r region and this purpose was achieved. In general, the data obtained from Bureau of Mines base titanium and iodide titanium alloys were in agreement. Forging—Both as-cast and forged samples were employed. Samples were heated for hand forging by an oxygen-hydrogen torch to the region 1200" to 1300°C. A titanium anvil and cover plate were used to prevent any iron pick-up and consequent formation of a low melting point compound. Frequent reheating kept the temperature in the desired range. Under these conditions, alloys containing up to 15.5 pct could be successfully forged. To check on the depth of contamination, forged alloys were heated slightlybelow the ß transformation temperature. Metal was removed to a depth below the contaminated surface so revealed, and the subsequent results obtained from these samples agreed closely with those secured from as-cast material. Heat Treatment—Prior to heat treatment, all alloys were vacuum annealed to remove hydrogen. Samples

Jan 1, 1962

[Queensland :-(Continued.) petrography of the Mount Morgan mine, LV, 263. Queensland tin mine and mill, Santa Barbara, Guanajuato, Mex., XXXVI, 227. Quenner disintegrator, XLI, 801; XLII, 15011. Quenstedt, F.: petroleum deposits, Suabia, XLVIII, 14881. Queretaro, Mex., silver mines, XXXIX, 360. Quicksilver: mining and reduction, LI, 110. Oceanic mine, Cambria, Cal., LI, 110. Quicksilver and iron decompose silver sulphide, XL, 872. Quicksilver deposits: China, -XL111, 49. Pacific slope, XXXVI, 1311.. Siberia, Vhdivostok district, XLIV, 16001.]

Jan 1, 1918