Search Documents

By M. Albertson

AT Cobalt, Ontario, Canada, a lake was drained to facilitate mining, by the Mining Corpn. of Canada, during the spring and early summer of 1915. Previous to pumping out the water, great quantities of sands and slimes from concentrating plants had been discharged into the lake and during and after the lake's drainage, its basin' Was a receptacle for tailing products. As the writer was at work along the shore line as the lake was being drained, he had a good opportunity to observe the changes that took place as the water was withdrawn. Some adjustments between the incoming sands and the mud in the lake had taken place before pumping was commenced. One of the most interesting results was the appearance of a small dome in a path the writer traversed twice a day for several months; he remembers distinctly the difficulty of crossing this. Cobalt Lake owed its existence to the gouging out of a rock basin by glaciation. The long axis of the basin closely follows the strike of a thrust fault of about 500 ft. (160 in.) vertical displacement. The lake was originally shaped somewhat as shown. The length was about 3000 ft. (914.4 in.), the width at the lower lobe was about. 1000 ft., and the, width at the narrows probably. 400 to 500 ft. The original depth of water varied from 20, to 30 ft. (6.1 to 9.1 m.), near where the island later was formed, to 60 to 70 ft. (23.6 to 27.6 m.) in the widest part of the lower lobe. At the narrows, the depth was 30 to 40 ft.. Above the bed rock was sand, with boulders near the bottom, and mud. During the building of the railroad in 1903, considerable filling was done along the right of way. With the commencement of mining operations, about 1905, waste rock and mill tailings were dumped into the lake. One of the mining companies operated a hydraulic giant to remove the glacial debris from several hundred acres of rock surface; much of the sand and clay from this operation was deposited in the. lake. About

Jan 2, 1921

By F. W. Osterwald, C. R. Dunrud

A continuously recording seismic network was constructed in 1962 by the U.S. Geological Survey to locate epicenters and record incidence of bumps (bounces, rock bursts) that occur in the bituminous coal mines of the Book Cliffs coal field near Sunny-side, Utah. The coal is mined because of its value as coking coal, although these bumps may be a hazard to life and property. Daily records of tremors caused by bumps for 1 3/4 years indicate that a seasonal pattern, as well as a daily pattern, exists for the number of bumps that occur in a given period. Maxima occur in May and June and November and December. Marked increases at 5-day to 9-day intervals are superimposed on these seasonal maxima. The largest bumps commonly occur during seasonal maxima when the rate of occurrence suddenly decreases and the amplitude of the individual bumps increases. Knowledge of this pattern may lead to prediction of general locations and periods of increased hazard from bumps. Experience to date has shown that prediction of precise times and locations of hazardous bumps is not possible, and may never be; primarily because even a small bump can be a hazard to life and property. Some bumps or bump sequences are actually composites, consisting or two or more discrete bumps a few tenths of a second to a few seconds apart. Violent and spontaneous releases of coal and rock from faces, ribs and roofs of mines (termed bumps or bounces by miners) are a common hazard to life and property in the coal mines located in the Book Cliffs near Sunnyside, Utah (Fig. 1). These bumps

Jan 1, 1965

By K. Winterton

The effect of a near-saturation unidirectional magnetic field was to decrease slightly the endurance life in Armco iron in the annealed condition. This is expected since the energy-absorbing mechanism associated with domain wall movemenfs is inhibited bv the strong field. THE factors determining failure under dynamic loading are not yet clearly recognized. One of the properties of a metal which might be thought to influence fatigue life is its damping capacity. Foppl1 conducted an alternating torsion test at a frequency of 700 cpm continuously for a period of 3 years, without the test piece breaking or showing any sign of deterioration after 1100 Million cycles of stress; the rate of dissipation of energy was sufficient to maintain the test piece at about 100°C above the ambient temperature. cazaud2 concludes from this, and others follow him, that ('the capacity for dissipation in the form of heat by internal damping is unlimited" and that therefore "damping is not directly related with fracture by fatigue." Future work may necessitate qualification of this rather uncompromising view. It is shown later that in all

Jan 1, 1960

In the last decade the railroads have been making tremendous strides in the development of services for the handling of bulk materials, the equipment for handling them, and the efficiency of handling, which resulted in lower costs to shippers. Pressure differential cars, giant tank cars and covered hopper cars, high capacity transloaders, and unit trains have led to substantial advances in expeditious, efficient, and economic handling of bulk materials.

Jan 1, 1973

By M. Gensamer

IT has been suggested by a number of people that it would be worth while for some one to attempt to summarize or condense the proceedings of this symposium. This task has fallen to me as organizer and co-chairman. Its difficulty will be appreciated by anyone who attempts to read the whole proceedings. It is therefore with trepidation that I offer the following digest. In recent years there has been a renewal of interest in America on this subject of the cohesive strength of materials, and a growing appreciation of the need for a better theory of cohesion failure. The theories of elastic action and plastic action are well developed, particularly the former. The theory of plastic action is still in the course of development, but it is well along. Plastic action is terminated by cohesion failure and what is needed is a theory that will tell us when to expect the cohesion failure. In the past it has generally been assumed that cohesion failure will occur when a critical value of the maximum tensile stress has been reached. Many experiments have shown that this is not strictly true, and this symposium concerns itself with the failures of this simple hypothesis, and with the efforts that have been made to devise a more satisfactory theory. The most active contributor in recent years to knowledge in this field is Dr. McAdam, and he was asked to open the symposium with a summary or condensation of his papers and views. Undoubtedly it is presumptuous to attempt a still greater condensation, but perhaps it will be useful, because even his contribution to this symposium contains no summary, no concise statement of just what his contribution has bees. Dr. McAdam makes two main points. The first is that the cohesive strength is not a single valued quantity, but that it is a function of all three principal stresses and hence must be represented diagrammatically by a surface in a three-dimensional figure. Dr. McAdam has attempted so to delineate the cohesion limit, basing his

Jan 1, 1944

By G. F. Dillion, A. F. Armington

THE present method for the ultrapurification of boron involves the formation, distillation, and decomposition of boron tribromide.' However, the boron tribromide prepared contains several impurities in the ppm range, even after distillation. Some of these impurities, notably carbon, can be reduced after decomposition by zone refining. In this study, a comparison of the purity of boron tribromide at various formation temperatures is presented. The apparatus employed consisted of a bromine flask connected to a 22 mm ID horizontal quartz reaction tube packed with amorphous boron powder, which was in turn connected to a receiving flask cooled with an ice bath. Argon was used as a carrier gas. The approximate rate of passage of bromine to the reaction tube was 25 g per hr. The reaction was first investigated at several temperatures in order to determine the lowest temperature necessary to produce a colorless product which was assumed to be an indication of complete reaction of the bromine. The lowest temperature found in this study was 420oC. The amount of impurities found in the boron tribromide at various formation temperatures is shown in Table I. The data presented are emission spectroscopic results of boric oxide produced by the hydrolysis of 2 to 3 g of boron tribromide in 10 ml of distilled water. After hydrolysis, the samples were dried several hours on a hot plate. Assuming equilibrium conditions in the reactor, one can make approximate thermodynamic calculations estimatling the completeness of reaction of bromine with boron and its impurities at various temperatures. Data for these calculations were taken from Rossini,3 and must be taken as approximations since the T?S factor was not included in the calculations. The results of such calculations indicate that, with the exception of carbon bromina-tion, all impurities would react almost to completeness (> 99 pet) at all temperatures between 400" and 900oC. In the case of carbon, which cannot be accurately analyzed spectroscopically, it is estimated that only about one sixth as much carbon tetrabromide would be formed at 400" than at 900°C. Since some marked reductions in impurity content were observed at the lower reaction temperature which would not be predicted by thermo-

Jan 1, 1962

By W. Rostoker, S. A. Spachner

FOLLOWING the discovery of the w transition phase in certain titanium-chromium alloys by Frost, Parris, Doig, and Schwartz, much interest has centered on the alloys in which this phase is found and its mode of precipitation. The w phase has been found in alloys of Ti-Cr, Ti-Fe, Ti-Mn, Ti-MO,2 and Ti-v.3 The temperature-time-transformation characteristics have, as yet, not been determined for most of these. In this study, such transformation characteristics have been investigated for two heat-treatable titanium alloys known to exhibit transition phase phenomena. The alloys chosen, Ti-8Cr and Ti-13M0, are representative of two classes of binary equilibrium systems. In the

Jan 1, 1959

By A. F. Knoll, T. Clinton Taylor

Qualitatively, galena (native lead sulfide) reacts with aqueous solutions of the xanthates,1 and has its surface sufficiently altered so that there is a tendency for air bubbles to attach themselves to the mineral crystals where there was no such effect before the treatment. This property is utilized in froth flotation operations where the mineral sulfide particles are raised into the froth and the gangue whose surface is not altered remains behind. The results of a study of this reaction were reported2 recently and certain tentative suggestions about the interaction of galena and the alkali xanthates were offered. In this paper, there is set down the results of a detailed quantitative investigation of the ions involved in this interaction with a view to finding out more about the condition existing immediately at the surface of a crystal like a heavy metal sulfide after treatment with an organic reagent. Past experimental experience showed that finely ground galena shaken with aqueous potassium xanthate abstracts xanthate ion and at the same time sulfate ion, reducing ions of the type (SmOn)= where the ratio of m to n is less than 4:l (as in sulfate), sometimes hydroxyl ion, are thrown into solution.3 Ions Involved in Xanthate-galena Interaction The present quantitative study of the galena-aqueous potassium xanthate system shows that at the lower concentrations of potassium xanthate (less than about 25 mg. per liter) the amount of xanthate ion abstracted by the galena can be accounted for by the amount of reducing ions of the (SmOn)= type and sulfate ion thrown into solution. At these

Jan 1, 1935

By J. F. Smith

ELASTIC constants of yttrium and eleven of the rare earth elements have been measured. This has been accomplished by measuring the propagation velocities of ultrasonic pulses. The velocity measurements were made by noting the elapsed time between an applied pulse and the appearance of successive echoes. The pulse-echo technique has become relatively common, and the basis of the measurement is outlined in several standard tests, e.g., Heuter and Bolt.1 Two important assumptions are made when using this method for the determination of elastic moduli. First, the pulse is assumed to propagate as a plane wave. To justify this assumption, the cross section of the test specimen should be large compared to the wave length of the transmitted pulse. For these measurements on the rare earth elements the minimum cross section wave length ratio was about 20. A second assumption which must be made when using polycrystalline specimens is that the grains are sufficiently numerous and randomly oriented so that the specimen may be approximated as elasti-cally isotopic. The grain size in the as-cast specimens which were used is believed to be sufficiently fine for this approximation, and the degree of preferred orientation is believed to be small. Supporting this viewpoint is the fact that elasticity measurements by the pulse-echo technique on as-cast specimens of other metals give results which are in satisfactory agreement with values obtained by other techniques. Hence, it is believed that the measured elasticity values for the rare earth elements are not apt to be seriously in error due to the assumption of elastic isotopy. The apparatus used in this determination was a modified Sperry Reflectoscope with a precisely calibrated time base circuit. Piezoelectric transducers were used both to generate the pulse and to detect the echoes. X-cut quartz crystals were used for the longitudinal modes, and Y-cut quartz crystals were used for the shear modes. Frequencies of 2.25 and 5 megacycles per sec were employed. Most of the specimens were 2.5 to 5.0 cm in length. Results Table I is a tabulation of the measured propagation velocities of longitudinal waves and of shear waves, together with densities obtained by Sped- ding, Daane, and Herrmann2 from lattice parameter measurements. The shear modulus, Poisson's ratio, and Young's modulus were calculated from the data in Table I through use of the following relationships: µ = pv32 [1] s=2-(vb/vs)2/2[1-(vb/vs)2] [2] and Y= 2µ(l+s) [3] where s is the shear modulus, Y is the Young's modulus, s is Poisson's ratio, p is the density, V0 is the longitudinal wave velocity, and v, is the shear wave velocity. The calculated quantities are shown in Table 11. Compressibility values can be computed from the relationship and the computed values may be compared with measured values obtained by Bridgman.8 Table III lists the data for such a comparison. The agreement is satisfactory, being particularly good for neodymi- um and gadolinium, poor for samarium, and intermediate for the other elements. Some variation is expected since Bridgman's measurements are isothermal, whereas the present measurements are adiabatic. In addition there may be some effect due to small variations in purity. Though most of the rare earth metals measured by Bridgman and all of the metals used in the present measurements were prepared at this laboratory, minor purity variations might exist since the samples came from different lots. Also, any imperfections such as dislocations, vacancies, voids, grain boundaries, microcracks, etc., should contribute to the volume change of a com-

Jan 1, 1958

The Maas patent drill-hole compass, for determining the direction and dip of drill holes, is successfully used to a depth of 3,000 ft. APPARATUS FOR SURVEYING DEEP DRILL HOLES. The compass is placed in a thermos bottle or glass tube with hot liquid gelatine and lowered in a water-tight phosphor-bronze case, with a tube containing hydrofluoric acid. When the gelatine is cold the rods are pulled, the direction of the needle is marked on the tube which contained the acid, and the direction and inclination of the hole determined from this tube in a goniometer. There is nothing to get out of order and the compass can be used by any drill foreman, the mark and etching on the tube making a permanent record of direction and inclination. (See Fig. 1.)

Jan 1, 1916

By P. Shahinian, J. Weertman

Minimum creep rates of nickel samples were measured in the stress region of 2.5x107 to 2.8xl0 dyne per sq cm and the temperature region of 400° to 1100°C. The creep rate seems to be proportional to (stress) at stresses below 7x10H dyne per sq cm. The activation energy of creep is approximately 65,000 cal per mol. IN a recent theory' of steady-state creep which is based on Mott's dislocation climb mechanism, the following creep equation was derived for creep in polycrystalline metals (if where K is creep rate, Q the activation energy of self-diffusion, S the entropy of activation of self-diffusion, L' the grain size, L the subgrain size, b the length of the Burgers' vector of a dislocation, u the shear modulus, u the stress, a the critical shear stress, M the density of active Frank-Read sources, v the vibrational frequency of a vacancy, and kT has its usual meaning. This equation predicts a creep rate which depends on the stress through a power law at low stresses. At high stresses the creep rate increases much more rapidly with stress. The theory breaks down for stresses great enough that the inequality holds true. It was the purpose of the present in-

Jan 1, 1957

By C. K. Leith

The ores of the region are contained in rocks of pre-Cambrian age, which, for most of the country up to recent years, have usually been referred to as “crystalline schists” or “crystalline complex;” and regarded principally as a metamorphosed basement-unit upon which the sedimentary rocks, beginning with the Paleozoic, were laid down. In the Lake Superior region this pre-Cambrian complex presents an' unusual variety of rocks with determinable relations. It has been possible, with the large expenditures which the magnitude of the iron-mining industry warrants, to work out their stratigraphy to a larger degree than bas been possible in almost any other area of pre-Cambrian rocks. [The portion here omitted contains descriptions of the Archean, Algonkian, and Keweenawan rocks of the several districts, their structure, distribution, correlation, and succession. Table I. and the geological map of the Lake Superior region belong to this portion, but are here reproduced on account of their value as guides to the readers of the rest of the paper.] The simplest and clearest conception of the pre-ambrian succession for the Lake Superior region may perhaps be obtained by thinking of it as primarily divided into six series-Keweenawan, Upper Huronian, Middle Huronian, Lower Huronian, Keewatin, and Laurentian-all but the last two separated by unconformities of varying and disputed relative im-

Jan 1, 1913

By William Catron, Cyril U. Colledge

BECAUSE the rich La Colorada orebody of the Cananea Consolidated Copper Co. does not outcrop at surface, after its discovery (by churn drill) and before mining was begun, a large amount of development work was done to learn the shape and extent of the ore and to provide for economic and effective mining. As these openings progressed, the actual shape of the orebody became known and with this knowledge came the realization that mining this rich and unusual deposit without loss of ore or danger to workmen presented several difficult problems. This paper will describe one of these problems; namely, the handling of an inverted cone-shaped core of barren rock, on the periphery of and below which the ore occurred. It was clear that as the ore was mined out from around and under this inverted cone of rock, weighing about 3,000,000 tons, it would hang over the workings, held suspended only by its own tensile strength and threatening to crash into the stopes below with disastrous results to men and mine. The method of mining developed during the years 1928, 1929 and 1930 anticipated and provided for the eventual collapse of this core of rock. In November 1936 the core settled down gradually on the edges of the stopes descending a total of about 50 ft. vertically. The men in the stopes had ample warning and no lives were endangered. There were no air blasts in the mine. The core broke loose from its top support at the 500-ft. level along old fracture planes and evidently is crushed to the ninth level. Movement was of short duration; the following shift went to work in the stopes as usual. No ore was lost. GEOLOGICAL STRUCTURE The shape of the orebody is illustrated in Fig. 1. The geology of the Colorada orebody has been described by V. D. Perry1 and by W. G.

Jan 1, 1938

By Douglas Bunting

IN THE anthracite fields of Pennsylvania, mine fires occur with more or less regularity and their existence is an ever-present hazard in coal mining. In all probability 90 per cent. of the mine fires can be ascribed directly or indirectly to the ordinary miner's open lamp. Other causes may be smoking, electrical installations, gas explosions, gas feeders, and the communication of fire to the outcrops from ash dumps, culm banks, timber and brush fires. Fires in pump rooms, engine rooms, and barns have been largely eliminated as a result of the Act of .Assembly, approved June 15, 1911, which provides that all inside buildings, including engine rooms, pump rooms, barns etc. shall be constructed of incombustible materials. Smoking of pipes, cigars, and cigarettes should be prohibited in the mines and too much care cannot be exercised in preventing fires by enforcing all rules designed for that purpose. Mine fires that involve underground fighting are invariably dangerous, and all fires, irrespective of the method pursued in extinguishing them, involve property loss and expense. Each fire generally presents a more or less original problem, dependent on the particular conditions. Generally mine fires may be divided into two classes: Those occurring in inaccessible workings and those occurring in accessible workings. The methods pursued in extinguishing or controlling mine fires are as follows: (1) direct attack, (2) smothering by sealing, (3) flushing with silt or other solids, (4) flooding with water, (5) cutting off, (6) surrounding with incombustible materials, (7) digging out by stripping from the surface. Most fires are extinguished in their incipiency by direct attack and failure to extinguish by this method is due to late discovery, lack of water, and facilities for fighting, or improper procedure in the initial attack. Should the method first pursued be unsuccessful, careful consideration should be given in determining next the method to be adopted; then the work should be carried on as rapidly as possible and under the supervision f the most competent persons. Materials and supplies should be fur-

Jan 9, 1921

By J. W. Dougherty

THE Hollinger gold mine is in the Porcupine mining division, District of Cochrane, in the northern part of the Province of Ontario. The adjacent town of Timmins, with a population of 25,119, lies 490 miles by railway north of the city of Toronto. GEOLOGY The property is situated on the northwest limb of a major syncline, which pitches northeast at approximately 50°. The principal rocks of the Hollinger area are of pre-Cambrian age and consist of altered, schistose, Keewatin lava flows intruded by stocks of schistose, quartz-feldspar porphyry generally assigned to the Algoman period. The structure of the Keewatin series is extremely complex as a result of close folding and some faulting. The schistosity, trending north 70° east and dipping steeply to the southeast, is most highly developed along a subsidiary anticline in which the major porphyry bodies occur. The ore bodies, which exhibit three principal structures, consist of quartz veins and associated pyritized wall rock. Some lodes are com-posed of en echelon veins, others exhibit a main quartz body with branch-ing stringers and a third consists of a single definite lead. Gold, in a coarse visible form, may be confined to quartz in some ore bodies but in others it is finely divided and is found not only in quartz but also asso-ciated with pyrite in the adjacent wall rock. In many veins the dis-tribution of gold is such that there are several ore sections, separated by areas of low-grade material, in the same vein although its physical appearance remains unchanged.

Jan 1, 1940

By Lynn G. Howell, Alex Frosch

In a previous article1 we have described a technique for measuring the relative intensities of gamma rays from the radioactive elements occurring naturally in geological formations along the walls of a borehole. The apparatus consisted of two Geiger-Müller tubes mounted inside a pressure-tight chamber. Each counter tube was coupled separately to an amplifier and a frequency meter at the surface by means of a multiconductor cable upon which the chamber was suspended. The output currents of the two frequency meters were recorded on a photographic paper as the chamber was moved in the hole. These traces showed remarkable correlation with the geologic formations, as evidenced by comparison with commercial electrical logs.2 Owing to the penetrating power of the gamma rays, logs may be taken in both open and cased boreholes. The apparatus has recently been changed somewhat. One of the counter tubes has been removed and a stage of amplification has been added inside the chamber. This arrangement seems to give a more favorable signal-to-noise ratio and satisfactory logs can be now made in cased holes and also in open holes as previously. Briefly described, the chamber moving in the hole is made of 3½-in. drill pipe and is about 10 ft. long. There is an additional extension about 2 ft. long at the top, inside which cable connections are made. The Geiger-Müller tube is mounted inside the bottom end of the chamber. Above this is the vacuum-tube amplifier with its batteries and transformer. In the top part of the chamber, small 45-volt batteries are mounted, which in part supply the high voltage for the counter tube. Additional voltage is supplied from the surface through the multiconductor cable upon which the chamber is suspended. Also, the output of the transformer in the single-stage amplifier is coupled to another single-stage amplifier at the surface through this cable. The surface amplifier is coupled to the Thyratron-controlled frequency meter, the tank circuit of which consists of a one megohm resistor across which is a bank of condensers varying in

Jan 1, 1940

By John Freeman

THE die pressing of brass may be described as a method of producing irregularly shaped parts of brass and other copper alloys by hot deformation in a die under pressure. Die pressing of brass was first developed as an improvement on sand castings in order to obtain irregularly shaped articles of brass with superior surfaces, a closer tolerance in dimensions, a denser structure, freedom from porosity and elimination of the relatively large amount of scrap invariably attached to sand castings. The freedom from sandy surfaces with consequent greater tool life in machining operations was also recognized as well as elimination of losses due to the uncovering of blowholes in machining operations. Die pressing also gave alloys of superior strength. Die pressings today are made from extruded rod or shapes, according to design of the part to be made. The greater number of pressings are made from round rod, because of its relatively lower cost and ease of handling. The rod is first sheared or sawed into desired lengths, the diameter of rod used and length of "slug" or "rivet" depending upon ultimate weight and shape of the die-pressed part to be made and design of die. The dimensions of the slug are figured so as to give the, minimum amount of scrap to be sheared from the pressing as it comes from the-die. Extruded shapes having I, T or X sections are often used when the finished part is to have a similar shape or heavy sections are joined by relatively light sections of considerable length. A rod bent in the shape of a U is also used on occasion, for similar reasons. Proper shearing of the slugs is of considerable importance. The sheared ends of the slugs should be as flat and straight as possible. Improperly sheared ends having an angle to the axis of the bar or a rough, uneven surface are liable to give folds or laps in the finished pressing and proportionately high rejections. The property of shearing varies considerably with different alloys and should be considered in the selection of a material for a given part. Where satisfactory shearing is not possible, the slugs may be cut from the bar by power saws. Extruded

Jan 1, 1931

By Alex Frosch, Lynn G. Howell

In a previous article1 we have described a technique for measuring the relative intensities of gamma rays from the radioactive elements occurring naturally in geological formations along the walls of a borehole. The apparatus consisted of two Geiger-Müller tubes mounted inside a pressure-tight chamber. Each counter tube was coupled separately to an amplifier and a frequency meter at the surface by means of a multiconductor cable upon which the chamber was suspended. The output currents of the two frequency meters were recorded on a photographic paper as the chamber was moved in the hole. These traces showed remarkable correlation with the geologic formations, as evidenced by comparison with commercial electrical logs.2 Owing to the penetrating power of the gamma rays, logs may be taken in both open and cased boreholes. The apparatus has recently been changed somewhat. One of the counter tubes has been removed and a stage of amplification has been added inside the chamber. This arrangement seems to give a more favorable signal-to-noise ratio and satisfactory logs can be now made in cased holes and also in open holes as previously. Briefly described, the chamber moving in the hole is made of 3½-in. drill pipe and is about 10 ft. long. There is an additional extension about 2 ft. long at the top, inside which cable connections are made. The Geiger-Müller tube is mounted inside the bottom end of the chamber. Above this is the vacuum-tube amplifier with its batteries and transformer. In the top part of the chamber, small 45-volt batteries are mounted, which in part supply the high voltage for the counter tube. Additional voltage is supplied from the surface through the multiconductor cable upon which the chamber is suspended. Also, the output of the transformer in the single-stage amplifier is coupled to another single-stage amplifier at the surface through this cable. The surface amplifier is coupled to the Thyratron-controlled frequency meter, the tank circuit of which consists of a one megohm resistor across which is a bank of condensers varying in

Jan 1, 1940

By Ernest Gayford

THIS is a nontechnical paper on flotation, subdivided under three general headings: (1) Definition of flotation; (2) what flotation is now doing in Utah; and (3) what is the future of flotation? . DEFINITION T. A. Rickard defines flotation1 as "the act or state of floating," from the French flottaison, water-line and fitter, to float. The dictionary defines flotation as "the science of floating bodies." The flotation process is a method of concentrating ores by frothing. Weinig and Palmer 2 define flotation as follows: What is the flotation process? Briefly, it consists in the agitation of finely divided ore in water containing bubbles of air or gas, a small amount of oil and, usually, other reagents, soluble and insoluble; under these conditions the small parti- cles of native metals, sulfides, arsenides, antimonides, selenides and tellurides show a tendency to attach themselves to the 6lms of the bubbles, and are thus carried to the surface of the water. The oxidized gangue minerals, such as quartz, feldspar, limestone, hematite, etc., show much less affinity for the bubbles, are easily wetted by the water, and either remain in suspension in the water, or sink to the bottom of the vessel. If the bubbles are sufficiently stable they can be removed, carrying their load of sulfide-mineral particles with them. Thus there can be effected a separation of the two classes of minerals from each other, assuming that the grinding has been sufficient to unlock all of the particles of different composition. The separation does not depend upon differences in specific gravity of the various minerals; in fact, the sulfides are usually heavier than the oxides, and some of the heaviest sulfide minerals are the easiest to float. A particle of mineral may be so large, however, that its weight will counteract its affinity for the film of the bubble. In most cases the ore must be fine enough to pass a screen having at least 48 meshes to the linear inch. Taggart defines flotation as follows : Flotation is a method of wet concentration of ores in which separation of mineral from gangue is effected by causing the mineral to float at or above the surface of a body of liquid pulp while the gangue becomes or remains submerged. The method

Jan 1, 1928

By B. G. Ricketts, A. Kelly, P. A. Beck

The isothermal kinetics (at 200" to 400°C) of subgrain growth and of softening were studied in a 99.997 pct pure Al crystal rolled to 80 pct RA, under conditions where recrystallization did not take place. It was found that the kinetics of subgrain growth and of softening were similar, and that the correlation between subgrain growth and softening was in first approximation independent of the annealing temperature. It has been shown by Heidenreich' by means of electron transmission microscopy and by Hirsch and Kellar2 by means of an X-ray microbeam technique that the crystals of heavily cold-worked polycrystalline aluminum consist of subgrains of approximately 2µ diam, which are slightly disoriented with respect to each other. This substructure is found on cold working at room temperature, without annealing. A preliminary study has been previously published3 of the softening upon annealing at 350°C of a heavily cold-rolled aluminum single crystal. Softening and X-ray line sharpening for such a rolled aluminum crystal were later studied in more detail as a function of annealing time and temperature.4 Perryman5, 6 has studied the recovery of polycrystalline aluminum after cold rolling. By means of phase contrast microscopy he found that the subgrain size increases with the annealing temperature but does not alter very much with annealing time at a given temperature. In the present work further study was made of softening as a function of annealing time and temperature and subgrain sizes were determined by two different techniques in an attempt to find any correlation that may exist between softening and subgrain growth. Subgrain size measurements were made both by the X-ray microbeam technique and by transmission electron microscopy. EXPERIMENTAL PROCEDURE For the X-ray studies specimens were cut from

Jan 1, 1960