Search Documents

By T. V. Moore

IN many of the important problems of the petroleum engineer, it is necessary to know accurately the laws governing the flow of gas and liquid mixtures in vertical' pipes. Although much work has been done along these lines, no satisfactory solution to the problem has been found. A good theoretical discussion of the energy balance in a gas¬lift has been published-by Versluys.1 One of the most important factors affecting the efficiency of the flow of oil and gas mixtures is slippage, and in most of the experimental work that has been done no provision has been made for the measurement of this quantity. As Versluys pointed out, since there is no method now known to estimate it from the data usually taken; slippage must be determined empirically. This paper presents the results of some work carried on to, measure slippage in short experimental gas-lifts. As shown herein, slippage can be easily calculated in a vertical pipe carrying a mixture of oil and gas if the fractions of the pipe occupied by liquid and gas respectively are known. In this work, the fraction of the pipe occupied by the liquid was measured under a wide variety of conditions and the relationship between this fraction and other quantities, which are easily measured in ordinary work, was determined. It was hoped that the quantitative relationship obtained from this work could be used-for making accurate calculations in flowing or gas-lift wells, but unfortunately it did not check satisfactorily when applied to actual wells. Apparently flow in long flow pipes is mote efficient than in the short ones used for the experimental work. Nevertheless, it is felt that the data themselves are of interest; that the method of attack may be of value in future work and that the relationship derived between slip and the relative velocities is a contribution toward the solution of the gas-lift problem.

Jan 1, 1931

By Robert G. Peets

After 216 years, the end of operations at the Corn- wall mine can be foreseen within the next two decades. The story starts in 1732 when three sons of Wiliam Penn-John, Thomas, and Richard-deeded 9669 acres in the Province of Pennsylvania to a Joseph Turner, who assigned it to William Allen. In 1734 Peter Grubb, who had prospected for iron in the area, paid Allen £ 135 for 300 acres of this tract in what is now Lebanon County. In 1737 he was granted a warrant for 142.5 additional acres, which included three hills of outcropping magnetite described as "rich and abundant, forty feet deep, commencing two feet under the earth's surface." This seemingly inexhaustible reserve was to become one of the most valuable deposits in the U. S. before the ore-rich Lake Superior region was developed.

Jan 7, 1957

By Edwin Chance

DURING the past 10 years, the safe and efficient lighting of the coal mines of this country has received an ever-increasing amount of attention. Several States have passed laws attempting to regulate the type of lamp to be used and the nature of the fuel to be burned, and the mining departments of coal-mining States have generally shown a keen and intelligent interest in this subject. The passage of the recent Employers' Liability Act in Pennsylvania has made it necessary for many coal-mining companies to take out liability insurance, and the companies underwriting such insurance have made it desirable for the insured to permit the use of, none but illuminants of established worth. While these conditions have not obtained for a sufficient length of time to permit the statement that the illumination of coal mines by portable lamps has been standardized, still, considerable progress has been made and the direction of future practice in this branch of coal-mining technology is very evident. Under these conditions it seemed that a review of the methods now used in coal-mine illumination, together, with a brief consideration of the principles underlying these methods, might be of some interest. Miners' lamps may be divided into three classes: The open light, the electric cap lamp and the flame safety lamp. It will be desirable to consider each of these classes separately, as each has properties peculiar to itself and one class is hardly comparable with another. In this country, without question, the open light is the most generally used of all miners' lamps. This fact is explained by the relative freedom of a large proportion of our mines from gaseous conditions, and by the admirable systems of ventilation installed in those that show a tendency toward such conditions. In the metal relines, the miner's candle has had and still has considerable vogue. Because of the small amount of ventilation usually supplied in metal mines, the freedom of the candle from any tendency to produce noxious gases or offensive odors, and the small amount of air it consumes, are. valuable assets, while, because

Jan 2, 1917

By S. M. Runke, R. G. Meara, O&apos

The Bureau of Mines has been charged by Congress to investigate processes for the production of alumina from low-grade bauxite, alunite, and clay. As one part of the program, an investigation of the application of ore-dressing methods to improve the grade of high-silica bauxite is in progress at the Mississippi Valley Experiment Station at Rolla, Mo. This paper summarizes data obtained so far and presents detailcd results of tests on four typical samples. Mineralogy of Batjxite The name bauxite originally was used to designate the dihydrous aluminum oxide (A1203.2HzO). The designation has been retained, although the existence of a specific mineral of such composition has been disproved. The term is now applied to ores of aluminum consisting of various mixtures of the minerals gibbsite (AlzOa.3H20), diaspore (A120a.H20), and boehmite (Alr-03.H20). The predominant hydrous aluminum oxide in most American bauxite, however, is gibbsite. In some instances bauxite may be amorphous mixtures of the hydrous aluminum oxides that approximate the composition of dihydrous aluminum oxide (A1203.2Hz0). The proposed name for this material is cliachite. Gibbsite and boehmite, the trihydrate and monohydrate, are soluble in a solution of sodium hydroxide at elevated temperature and pressure, whereas diaspore is practically insoluble. The solubility of these two minerals is the basis of the Bayer process of alumina extraction. All bauxites contain certain impurities, the commonest of which, in the order of their importance, are: silica, principally as a constituent of kaolinite, and to a lesser extent as quartz; iron, as hematite, limonite, and siderite; and titanium, as ilmenite, rutile and leucoxene. Minor impurities are zircon, cobalt and nickel. Bauxite is produced commercially in Arkansas, Alabama, Mississippi, Georgia and Tennessee, but the most important deposits in the United States are in Arkansas, in the vicinity of Little Rock. History of Batjxite Beneficiatjon The literature on bauxite beneficiation is limited, but the reports of Gandrud and DeVaneyl and Clemmer, Clemmons, and Stacy2 show the possibilities of flotation as a means of beneficiating bauxite. Their work has also developed reagent combinations that are satisfactory for flotation of gibbsite.

Jan 1, 1944

By P. W. Rainier

THE Chivor emerald field is situated on the eastern slope of the Andes in the Department of Boyacá, at an elevation of about 8000 ft. above sea level. It overlooks the Llanos (plains) of the Orinoco and is watered by many streams flowing into the Rio Meta, the Orinoco's largest tributary. The Rio Meta is navigable from the Orinoco to a point within about 50 miles of the Chivor district and may eventually prove to be the reasonable outlet for the future development of this part of the country. The topography of the district is extremely rugged and mountainous (Fig. 1), the difference in elevation between two points on a mining claim 1 km. square being sometimes as much as 4000 ft. The ground is covered with dense forest growth and the available timber is suitable and sufficient for mining purposes, but it is becoming gradually depleted by Indian clearings as the country around the mines becomes settled. The many streams combined with the rough topography give good possi-bilities for hydroelectric power. The center of population nearest to Chivor is Bogota, the capital of the republic and a city of some 300,000 inhabitants; the distance is two and one-half days' travel. The first stage of the journey from Bogota, is accomplished by rail to Chocontá, some 4 hr. travel. From Chocontá the journey is made in the saddle, one night being spent in Guateque. The latter is a small town and the nearest post office to the mines, being some 10 hr. ride distant. The roads are mere bridle paths, in parts hazardous and almost impassable in the wet season. All supplies brought to the mines, other than those produced locally, are carried by pack mule; mule freight from Chocontá costs 3 centavos1 per pound. The climate of the Chivor district is healthful and bracing. The wet season begins in March and concludes in November, the remaining months being dry. The annual precipitation is about 150 in. The temperature throughout the year is nearly constant, varying from about 45° F. to about 65° F. shade temperature. The rains are cold and unpleasant, and for the greater part of each day in the wet season the country is shrouded in dense mist. A fire can with comfort be kept burning in a living room all the year round. There are a few slight

Jan 1, 1929

By S. W. Poole, J. A. Rosa

The object of this investigation was to determine the distribution of chemical elements within a large, killed alloy-steel ingot, by sulphur printing and quantitative chemical analysis. With regard to segregation in steel ingots, the factors of melting practice, pouring temperatures, mold design, etc., and the mechanics of solidification and its attendant functions, have been the subject of intensive study over a period of years by many investigators. Notable among these is the Sub-committee of the No. 5 Committee of the British Iron and Steel Institute. For an exposition of the many problems awaiting the researcher on the heterogeneity of steel ingots, the methods of attacking these problems, together with some of the answers, the reader is referred to the nine reports and numerous papers of that committee and its membership. Steelmaking Data Melt.—The heat was made in a 70-ton direct arc-type basic electric furnace. Furnace charge consisted of nickel-chromium-molybdenum steel, most of it in the form of heavy mill scrap. All of the scrap was charged cold. The standard double-slag method was employed, the heat being finished under a strong carbide slag. Aluminum was used as the deoxidizing agent. Tapping tempera- ture, as observed with an optical pyrometer, was 3000°F. Detail of Mold and Ingot Size.—Details of the ingot mold and the ingot itself are given in Fig. I. Teeming.—Teeming temperature of the subject ingot as observed with an optical pyrometer was 2830°F. The ingot was top-poured directly through a 1 1/2-in. nozzle and required 7 min., 44 sec. to fill up to the hot top. An additional 2 min., 30 sec. were required to fill the hot top. The ingot was stripped hot and charged with the remainder of the heat into an annealing furnace. There it was given the standard annealing cycle used for these ingots. Subsequent heat-treatments are described elsewhere in this paper. Sectioning and Preparation for Sulphur Printing Because of previous favorable experience in sectioning ingots up to 21 1/2 in. square with an oxyacetylene torch, it was decided to use this method to section the subject ingot. The ingot was preheated to 900°F. for 12 hr. It was then placed on a steel bed in a horizontal position so that the longitudinal axis was level and parallel to the track of the motor-driven torch carrier. Two cuts were made, one 2 in. above the longitudinal axis and the other 2 in. below. The time required to make each cut was approximately 75 min. The cutting operation is shown in Figs. 2 and 3. The 4-in. thick slab was mmediately charged into a furnace standing at 1200F.

Jan 1, 1945

By David E. Hyatt, Christopher H. Cox, Franklin T. Davis

INTRODUCTION The composition of water used in the flotation process has always been of primary interest to the flotation metallurgist. It is by alteration of the chemistry of the water introduced to the process that flotation separation is effected. In only a few cases has it been necessary to treat available water prior to use in the process. In the past, flotation tailings were treated for the removal of solids via the tailings dam and water decanted from the dam was either recirculated to the process or discharged to the surface water system. The choice of recirculation or discharge was based upon water availability, effect of recycle water on the process, and economic considerations. The Federal Water Pollution Control Act Amendments of 1972 have charged the United States Environmental Protection Agency with establishing effluent limitations from point sources of discharge into the navigable water of the United States. A detailed study, sponsored by EPA, of the water of ore processing plants took place in 1974 and 1975 and guidelines for these plants will presumably have been published by the time this paper has been presented(1). The action of many of the individual states preceded the EPA in this attempt to regulate the quality of the water discharged from industrial point sources. Even with recycle of tailings water, some water is discharged from tailings dams into the substrata and at least one state is currently preparing guidelines for the quality of water discharged into the substrata.

Jan 1, 1976

By Francis H. Brownell

During the 1920's lead consumption in the United States reached the highest average total ever known. For the ten-year period 1921-'30, it was slightly over 600,000 tons per year, or say 50,000 tons per month, and the price averaged 6.81 per lb. But the I930's witnessed a severe drop in the consumption of lead is in other business activities. The average U.S. consumption for the ten-year period 1930-'40 was slightly less than 380,000 tons per year, or under 32,000 per month, with the average price dropping to 1.191c. per lb. The outlook in early 1939 was for a continuation of this average consumption and price a demand of 35,000 to 40,000 tons per month, and a price level of 4 1/2 to 5c. in the United States.

Jan 1, 1941

By Dever Ashmead

FROM time to time metal-mine engineers have inquired why anthracite mines and their preparators are rarely operated on the two or three-shift basis. The subject may be approached as affecting: labor, development, the underground workers, the preparator, the outside workers, capital, the supply account, power consumption, the storage of coal over various shifts, railroad car supply, and the market. LABOR From the start, the adoption of a plan of three full-shift operations in a day would cause difficulty with the colliery employees, for they have never worked on that plan and would show their resentment by suspending work. Even if they could be induced to work according to this schedule they would not be as efficient, for they would be working more or less unwillingly at hours at which they are accustomed to rest. Operation on a three-shift basis would necessitate triple manning of each working place, and dissensions would arise between the men, for each shift would claim that the preceding shift had taken undue advantage and had not left as favorable conditions as it had found. To obviate these disputes it might be necessary to let out the work to a contractor, who would hire his helpers to mine out the chamber, or breast. The state mining law requires that a miner be put in charge of each working place. To conform with this provision he would have, to hire three helpers and two miners to mine the breast. The labor unions have been trying to abolish the subcontractor in mine work and any method of working that would cause his return, however innocent in purpose, would result in labor disturbances.

Jan 2, 1922

By N. W. Sager, H. W. Mossman

The arrangement and general dimensions of the reverberatory furnaces and waste-heat boilers for the Nos. 2 and 3 smelting units at the McGill plant of the Nevada Consolidated Copper Corporation are shown in Fig. 1. Each of the two reverberatory furnaces has its own set of waste-heat boilers, and before February, 1932, each furnace, when it was in operation, delivered waste-heat gases to its own boilers only. In January, 1933, the idea was suggested of using some of the waste-heat boilers as economizers to operate in conjunction with the waste-heat boilers that were generating steam. The execution of this idea gave rise to the gas-flow scheme depicted in Fig. 1, the advantages of which were obvious, particularly so in view of the fact that for some months prior to the adoption of this scheme the smelting had been confined to No. 2 furnace, with No. 3 furnace and its boilers idle. The waste-heat gases from No. 2 furnace pass through the boilers serving this furnace as steam-generating units, thence through the original exit duct to a point where a bulkhead diverts the gases in a reverse direction through two of the boilers of No. 3 furnace. After the gases have traversed these two boilers, another bulkhead placed in the duct between No. 3 furnace and its boilers causes them to traverse still one more boiler, from which the gas path leads to the stack. In this scheme the last three boilers traversed by the gases, i.e., the boilers behind No. 3 furnace, function as economizers and preheat the feed water for the two steam-generating units directly serving No. 2 furnace. This discussion will give consideration to the results obtained in waste-heat recovery by the scheme shown in Fig. 1, and, further, will compare these results with those obtained before the boilers of No. 3 furnace were set up to act as economizers, but before going into the detail of heat generation, distribution and recovery, will present some additional details of the equipment. All boilers in this waste-heat plant are of the Stirling type. The two behind No. 2 furnace, acting as steam-generating units, of class 13, are 40 tubes wide and rated at 1112 boiler hp., while the three boilers behind No. 3 furnace, acting as economizers, are also of class 13, but 28 tubes

Jan 1, 1934

By N. S. Greensfelder

THE firing of explosive charges by electricity dates back to 1745 when a Doctor Watson is said to have used an electric spark for igniting gunpowder. His method failed in practical application because, to ignite blasting powder, heat must be applied for a period longer than the duration of an electrostatic spark; Wheatstone found that this does not exceed 14000 sec. The usual result, therefore, of an electrical discharge in gunpowder is to scatter the grains, without igniting them. Benjamin Franklin partly overcame this difficulty by confining the powder and crushing grains that lay in the line of discharge. In 1822, after the primary cell had been discovered by Volta, Robert Hare, professor of chemistry at the University of Philadelphia, noticed the heating of a short piece of wire placed in the circuit of a voltaic battery. Later work by Oersted, Faraday, Wheatstone, and Henley resulted in the development of the magneto blasting machines. Fulminates of gold and silver are thought to have been discovered by Cornelius Drebbel, about 1600. Pepys, in his diary for November 11, 1663, recounts a conversation with Doctor Allen, who told him about aurium fulminans "of which a grain ... . put in a silver spoon and fired, will give a blow like a musquett and strike a hole through the silver spoon downward, without the least force upward.1," This fallacious belief that explosives act downwards only, is still held by many who should know better. Fulminate of mercury was discovered by Howard in 1799. J. Shaw of Philadelphia is said to have invented a fulminate-of-mercury cap in 1814; his idea was later adopted by gunmakers in England and France. The principal advantages of

Jan 9, 1922

CHUQUICAMATA, as the Chile Copper Company's mine is known, has the largest developed deposit of copper ore in the world. Indeed, it is improbable that its equal will ever be found. The Union Miniére du Haut Katanga, operating in the Belgian Congo, may some day surpass Chuquicamata in the total amount of copper produced; or one of the companies developing the rich copper region of Northern Rhodesia may ultimately outdo it. But in each instance, the ore will come from a group of mines separated by 80 miles or more; whereas the deposit at Chuquicamata is one vast integral mass containing as a minimum probably 1,000,000,000 tons of ore, averaging better than 8.5 per cent copper, and as a maximum-well, most any reasonable figure might err on the low side. Utah Copper approaches Chuquicamata more nearly than any other in tonnage of exploitable ore; but Utah's ore is less than half as rich. The figure for the aggregate copper content of the reasonably assured ore at Chuquicamata is breath-taking at 50,000,000,000 pounds. Other distinctions has Chuquicamata: It was the first of the Porphyry Coppers to use leaching as the method of treating the ore; its plant cost for producing is lower than that of any of the others, only Braden and Utah being close rivals; and it was worked for its copper long before any of the others. According to an authentic article published in Ingeniería Internacional (May, v 1982) the Incas smelted copper ores from Chuquicamata prior to 1536. Diego de ALnagro, to whom Charles V, King of Spain, generously allotted a one-fourth portion of South America lying south of Cuzco, the Inca metropolis, made an expedition into Chile in 1534. Better known to history, perhaps, is Pizarro, who was awarded the area immediately north, and who proceeded

Jan 1, 1933

By Martin A. Mayers

It has long been recognized that it would be highly desirable to be able to predict the temperatures at various points in a burning fuel bed and their variations with changes of the properties of the fuel and the rate of air supply. Experimenta1 investigations of fuel-bed temperature1-4 have not been lacking, but the absence of any theoretical background has made it impossible to use the results of these tests as a basis for prediction, except in a very general may. A mathematical analysis", based on a somewhat simplified theory of the distribution of lieat in a fuel bed, lias recently been completed by the author. Even though numerical values of some of the coefficients are not known, the calculations result in some conclusions of general significance. Thus, for example, it appears that when the temperatures throughout the fuel bed can be calculated, the rate at which ignition of the fuel by underfeed action can be maintained can also be calcu1ated. The uncertainty concerning the values of the coefficients referred to above is serious limitation on the use of that method. The following paper presents a discussion of these coefficients and includes estimates of their values based on the data now available. A brief description of the theory on which the analysis is based, and some results of the calculations showing their degree of agreement with experimental results, are presented by way of introduction to the discussion of the coefficients. For a more. extended discussion of the theory, see the A.S.M.E. paper5. Theory and Comparison with Experiment The theoretical analysis is similar to that used in the calculation of the stationary temperatures in a conducting solid in the classical theory of heat concluction. The fuel bed is pictured as a uniform, continuous, porous solid through the interstices of which air can be blown and ill which combustion can take place. The solid lias a finite thermal conductivity, so that heat may be transported in any direction, against the flow of air as well as in the same direction. While it is true that nothing

Jan 1, 1938

By Martin A. Mayers

It has long been recognized that it would be highly desirable to be able to predict the temperatures at various points in a burning fuel bed and their variations with changes of the properties of the fuel and the rate of air supply. Experimenta1 investigations of fuel-bed temperature1-4 have not been lacking, but the absence of any theoretical background has made it impossible to use the results of these tests as a basis for prediction, except in a very general may. A mathematical analysis", based on a somewhat simplified theory of the distribution of lieat in a fuel bed, lias recently been completed by the author. Even though numerical values of some of the coefficients are not known, the calculations result in some conclusions of general significance. Thus, for example, it appears that when the temperatures throughout the fuel bed can be calculated, the rate at which ignition of the fuel by underfeed action can be maintained can also be calcu1ated. The uncertainty concerning the values of the coefficients referred to above is serious limitation on the use of that method. The following paper presents a discussion of these coefficients and includes estimates of their values based on the data now available. A brief description of the theory on which the analysis is based, and some results of the calculations showing their degree of agreement with experimental results, are presented by way of introduction to the discussion of the coefficients. For a more. extended discussion of the theory, see the A.S.M.E. paper5. Theory and Comparison with Experiment The theoretical analysis is similar to that used in the calculation of the stationary temperatures in a conducting solid in the classical theory of heat concluction. The fuel bed is pictured as a uniform, continuous, porous solid through the interstices of which air can be blown and ill which combustion can take place. The solid lias a finite thermal conductivity, so that heat may be transported in any direction, against the flow of air as well as in the same direction. While it is true that nothing

Jan 1, 1938

By T. PH. D. Egleston

THE origin of gold both in placer deposits and in veins, and especially the origin of nuggets, has been the subject of repeated discussions and investigations, which have been recently brought to my attention by several extremely interesting specimens sent to me for examination, and more especially by the one exhibited at the meeting of the Institute in February, 1880.* In the year 1874 I made some examinations of the hydraulic mines of Califor¬nia, and was very much struck with the distribution of the gold throughout these deep placers, which were almost invariably poor on' the surface, while gradually growing richer towards" the bed¬rock. The constant presence of fossil wood, and the large quantity of organic matter contained even low down in these beds, was also remarkable. Not being satisfied with the various theories advanced to account for the formation of these deposits, I began an investiga¬tion early in the year 1879 on the conditions of solubility of gold and the causes of the loss in working gold ore in a large way: The researches which I have undertaken show that gold must be considered a soluble rather than an insoluble metal, and that the conditions of solution are such as will be found anywhere where gold is likely to occur, and the solution may take place even under the ordinary cir¬cumstances of surface drainage, and may be going on freely even where the presence of gold has never been suspected, and that there are causes enough in nature to produce the solution of the gold in sufficient quantities to account for all the phenomena of both the vein and placer formations. The general theory with regard to the formation of these placer deposits and nuggets has been that they were the result of the de¬struction of pre-existing- vein-matter, which does not accord with the facts as shown in the deep placer deposits. The gold in such case would be distributed in layers of unequal richness throughout * Transactions of the American Institute of Mining Engineers, vol. 8, p. 451.

Jan 1, 1881

By N. A. Gokcen

EQUILIBRIA in the reactions between gases and liquid metals have been the subject of many interesting investigations. The experimental realization of true equilibrium, however, is questionable in certain cases due to the lack of conclusive studies in reaction rates. It -will be shown here that a systematic interpretation of rate studies with the analysis of prevailing experimental conditions leads to valuable practical information. The reactions of particular interest are: H2(g) +S(inFe) - H2S(g) [1] H2(g) +O (inFe) =H2O(g) [21 2H2(g) + SiO2(s) = 2H2O(g) + - (inFe) [3] The usual and perhaps the most convenient method of investigation may be illustrated with reaction 1. A stream of gas mixture consisting of H2 + H2S is passed over or bubbled through the liquid metal at constant temperature. The ratio of H2S/H2 in the entrant mixture is fixed in each experimental run, and, therefore, the composition of melt varies until the establishment of equilibrium. The purpose of this paper is to derive a formula expressing the minimum time required for the establishment of equilibrium and to compare the calculated values from such a formula with the available data. Equations Reaction 1 is used for the purpose of illustrating the derivation. Let E represent the equilibrium and X the nonequilibrium sulphur in weight percent at any time t in minutes. For the sake of simplicity, it is first assumed that E > X although the results are of general applicability without restriction. It has been shown by Morris and Williams' that within a difference of 1 pct S or less, i.e., E-X5 1.00, the value of K'1 = Ph2s/Ph2.S% is very nearly constant. The maximum ratio of available Ph2s/Ph2 = H,S/H,, from which sulphur can be absorbed by metal, is equal to H2S/H2 in equilibrium with E (which equals H2S/H2 in the entrant gas), minus H,S/H, in equilibrium with X. Thus: Available H2S/H2 = EK'1 - XK'1 [4] Eq. 4 expresses that sulphur can be absorbed by metal from the H2S/H2 in the entrant gas until the gas leaving the metal assumes a value of H2S/H2 which is in equilibrium with the dissolved sulphur X at that time. H,S constitutes up to approximately 1 pct of the gas mixture. Its disassociation into H2 and SL is about 1 pct at 1600°C, hence, the H2S/H2 impinging on the surface of metal is very close to that in the entrant gas. The rate of flow of hydrogen entering the reaction chamber is kept constant experi-

Jan 1, 1954

By Charles Russell

PRESSURES developed by the coal during the coking process have been responsible for serious trouble to many companies that operate or build by-product coke ovens. The insidious nature of this trouble is indicated by the fact that oven operators, unless they have ascertained the charac-teristics of the coals they use, cannot determine the existence of dangerous pressures until after the damage has been done. A rather popular mis-conception is that ease of pushing of the charge at the completion of the coking period indicates that no dangerous pressure has been developed, but this is far from the truth; pressures developed during the coking period are often completely dissipated by the shrinkage of the charge in the completion of coking, and so any criterion based on the ease of pushing is futile. However, methods of testing coals are available that will definitely distinguish the dangerous coals from those that are safe, and such methods have been brought to a high degree of certainty. The operator should take no risk that involves either a lack of knowl-edge of the behavior of coals during coking or the failure to believe that certain of the coals or coal mixtures can cause damage to the oven struc-ture. This merely tends to minimize the problem and leads to claims that coking coals of all kinds may be carbonized with no danger of damage to the oven structure provided some particular kind of by-product oven is used. This lack of appreciation of the true situation is in itself one of the main factors leading to damage of coke-oven structures. Coals that develop more than a certain safe pressure cannot be used in by-product coke ovens without causing damage to the side flue walls. The following paper presents a highly certain method for the measure-ment of the pressures developed during the carbonization of coal-a method that is the culmination of many years of work on the problem in which a number of methods for the purpose were investigated and used. While actual pressures found may appear to be small when expressed in pounds per square inch, the number of square inches in each oven wall is so large that the total pressure on the oven wall becomes an enormous load.

Jan 1, 1939

By Stuart St. Clair

In view of the great interest shown in the oil possibilities of Kentucky, one is impressed with the paucity of reliable literature on the oil fields of the state. A few brief reports by the Federal and State Geological Surveys are about the only reliable data available. When the estimated production figures, for 1918, are published by the U. S. Geological Survey, they will show a revival of the oil industry in the Blue Grass State during the past half decade. There will also be an increase in the production for 1919 and 1920, at least. Although as an oil-producing state Kentucky is small, compared with some of the other oil states, the present production and the area of undrilled proved territory is large enough to classify it as one of the important oil states of the Union. This paper will be confined to the Irvine District and the immediately adjoining areas which have been prospected with varying success. The Corniferous limestone or Irvine sand is the oil-producing formation in the area discussed. In my divisional nomenclature, the Irvine District includes the Irvine field, which extends from the town of Irvine eastward toward Campton; the Big Sinking area, which joins and lies to the south of the eastern part of the Irvine field; the Beattyville area, which lies to the north and northeast of the town of that name and joins the Big Sinking area; and the Ross Creek pool, which lies to the southwest of the big production and across the Kentucky River. Except for the Ross Creek pool, the main producing area is bounded on the east by the L. & E. R. R. and on the west and south by the Irvine Branch of the L. & N. R. R. Winchester and Lexington form the gateways and Torrent on the east, Irvine on the west, and Beattyville on the south are the principle entrances to the main fields. Evelyn, on the L. & N. R. R., south of Irvine, is the point of entrance to the Ross Creek area. Geology The geology of the Irvine District is very simple. The rock formations with which the oil man should acquaint himself lie between the lower measures of the Pennsylvanian sandstones and shales and the Devonian or Corniferous limestone, or Irvine formation. Only a very brief description of these formations will be given, as they have been described fully by E. W. Shaw.'

Jan 1, 1921

By W. S. Hyler, L. W. Berger, R. I. Jaffee

Hydrogen additions of 390 ppm to A-55 titanium and 368 ppm to Ti-8 pet Mn have no deleterious Hydrogenadditionseffect on the unnotched and notched rotating-beam fatigue properties of these materials. 'These amounts of hydrogen, however, are sufficient to cause severe notch-impact thesematerials.embrittlement in A-55 titanium and pronounced loss of tensile ductility in Ti-8 pet Mn. The lack of embrittling effect in fatigue in the latter alloy is consistent with the postulated strain-aging mechanism of hydrogen embrittlement in a-ß alloys. There is a significant strain-agingincrease in the unnotched endurance limit of A-55 titanium with the addition of hydrogen. This increase may be explained as the result of internal heating effects which would dissolve the hydride and cause solid-solution strengthening. TITANIUM and its alloys may be seriously embrittled by relatively small amounts of hydrogen. The form which this embrittlement takes has been shown to vary with alloy type. The a alloys, for example, suffer most strongly from loss of notch-bend impact toughness' when sufficient hydrogen is added, and this effect has generally been associated with the presence of hydride phase in the micro-structure. In a-ß alloys, on the other hand, hydrogen is most detrimental to tensile ductility in slow-speed tests,2-1 and the embrittlement may be detected in a most convincing manner by means of rupture tests at room temperature. This particular kind of embrittlement has not been associated with a change in microstructure, but has been classified rather generally as associated with a strain-aging type of mechanism.' In the present paper, the effect of an embrittling amount of hydrogen on the rotating-beam fatigue properties of both an a and an a-ß titanium alloy is covered. For this study, annealed commercially pure (A-55) titanium was chosen as an a alloy, and equilibrated and stabilized Ti-8 pet Mn as representative of a typical a-ß alloy. Nominal hydrogen levels of 20 and 400 ppm were evaluated, the latter amount having been shown previously to be severely detrimental to the impact toughness of commercially pure titanium and to cause pronounced strain-aging embrittlement in the Ti-8 pet Mn alloy. The only report of the effect of hydrogen on the fatigue properties of titanium is given by Anderson et al.,° in which a push-pull type of fatigue test was conducted on as-received commercial-purity titanium sheet. Much scatter was found in the results, but generally the presence of hydrides slightly decreased the fatigue strength of unnotched specimens in the longitudinal direction. The results of notched tests were masked too greatly by scatter to be significant. Experimental Procedure Preparation of Materials—Analyses of the A-55 titanium and the Ti-8 pet Mn alloy used in this investigation are given in Table I, which indicates the 8 pet Mn alloy to be more nearly a 6 pet Mn alloy. This alloy will be referred to as Ti-8 pet Mn, however, since this is the commercially designated composition. Both alloys were received in the form of5/8-in. diam rod and, after suitable surface preparation, 5-in. lengths were vacuum annealed at 820°C. Half of the rods for each material were then hydrogenated at 820°C to a nominal hydrogen content of 400 ppm. The hydrogenated and vacuum-annealed A-55 rods were hot swaged at 700°C from 5/8-in. diam to 1/4-in. diam, and then annealed 1 hr at 800°C and air cooled prior to preparation into test specimens. Fabrication of the Ti-8 pet Mn alloy was by hot swaging to 3/8-in. diam at 760" and then 1/4-in. diam at 704°C. This material was then annealed 1 hr at 704", followed by furnace cooling to 593"C, and finally air cooling to room temperature. Evaluation—In order to examine more completely the effects of hydrogen on the particular materials studied, slow-speed tensile and notch-bend impact properties were determined in addition to fatigue data. Tensile specimens were of the standard ASTM type with a reduced section of 1/8-in. diam and a gage length of 1/2 in. A subsize cylindrical Izod specimen was used for impact tests. These specimens had a 45" notch with a 0.005-in. radius and a 0.150-in. root diam, and the stress concentration factor of this notch in bending was Kr = 3. Both the ten-

Jan 1, 1959

By P. S. Kotval, O. H. Nestor

Stacking fault energy measurements of nickel-base alloys have been mainly confined to binary and ternary systems. In this paper, the stacking fault energy has been measured by the rolling texture method in a series of ten alloys which comprise successive additions of Cr, Mo, Fe, and C to pure nickel, eventually resulting in an alloy of the composition of Hastelloy alloy X. The alloys studied here are single-phase, solid solutions with the exception of two alloys in which some undissolved particles of "primary" carbide have been retained. It is found that successive additions of chromium, molybdenum, and iron all lower the stacking fault energy, with iron having only a minor effect. The stacking fault energy is found to increase when carbon is added in solid solution. The results from the rolling texture measurements are correlated with thin foil observations of dislocation substructures in these alloys. In a recent paper' it was pointed out that the dislocation substructure of various superalloy matrices could be classified into three broad categories based on 'high', 'medium', and 'low' stacking fault energy. It has also been demonstrated2 that the dislocation substructure in each of these categories has a well defined role in the nucleation of strengthening precipitates which is different from the role played by the dislocation substructure in other categories. Thus, it becomes desirable to understand the influence of various solute elements on the stacking fault energy and hence on the dislocation substructure of the matrix, before any further development of superalloys by mi-crostructural predesign can be undertaken. Recently, Beeston and France have studied the influence of increasing solute additions on the stacking fault energy of a series of binary nickel-base alloys relevant to the Nimonic series using the rolling texture method, and have then estimated the effect of a given alloy addition in five commercial Nimonic alloys. However, comparison with stacking fault energy data from other investigations''5 suggests that the influence of a given solute element in a nickel-base binary system is not necessarily the same in a ternary or more complex superalloy system. Accordingly, the present work was undertaken to study the effect of successive addition of solute elements to pure nickel, the final composition being the nominal composition of Hastelloy X. The rolling texture method of stacking fault energy measurement was used since it can be used for the whole range of stacking fault energy values and does not have the disadvantage of, say, the Node method which is only applicable to low values of stacking fault energy. In addition, the rolling texture method provides a means of determining the stacking fault energy which is statistically more significant than that provided by other methods. EXPERIMENTAL TECHNIQUES Button heats of alloys of the compositions shown in Table I were prepared. Each button was remelted not less than four times. After a slight deformation (approximately 5 pct) all alloys were homogenized at 2200°F except alloys, H . I, and J. Alloys H and I were solution heat treated at 2150°F and alloy J at 2282OF. The buttons were cold worked by rolling, using "end-to-end" passes and intermediate anneals at the homogenization temperatures mentioned above. After each annealing treatment the samples were rapidly water quenched to avoid any precipitation. In alloys F and I, however, a few particles of "primary" carbides were retained even after the homogenization treatments at the temperatures mentioned above. Part of the solution heat treated material was cold worked to 0.04-in.-thick sheet and the penultimate reduction was -50 pct of deformation as recommended by Dillamore et al. All annealing was carried out in vacuo within sealed quartz capsules. Some of the material from each alloy was rolled down further to 0.004 in. strip for thin foil transmission electron microscopy specimens. Specimens of this strip were annealed at the homogenization temperature for 1 hr and then strained 7 pct by rolling at room temperature. Thin foils were prepared from the strip specimens by the 'window" technique using an Ethanol-Perchloric acid electrolyte at 32°F and a voltage of 22 v. Stainless steel cathodes were employed. All transmission electron microscopy was performed in a JEM-7 electron microscope using an accelerating voltage of 100 kv. Specimens from the 0.04 in. sheet which had been rolled -60 pct in the final pass were electropolished to remove the surface layers to a depth of approximately 0.002 in. Rolling texture pole figures for all the alloys were determined using a Schulz ring and nickel filtered CuKa radiation at 50 kv and 20 ma. The texture parameter Io/(lo + I,,) (where Io is the

Jan 1, 1970