Search Documents

By Charles H. Mitchell

British Columbia is enjoying a period of sustained high-level activity in all aspects and sectors of its mining industry. The total value of mineral production for 1962 was in excess of $229 million. This was the greatest total value attained for any year to date, exceeding the previous record year of 1956 by more than $40 million. It appears reasonable to expect that value of production for 1963, stimulated by increased production attained during the year, and by improved metal prices for some of the major products, will be substantially in excess of that recorded for 1962. Elsewhere in this issue appears a detailed report of prospecting and exploration activity in the Province. For the purposes of this review it is sufficient to state that the level of prospecting and exploration activity during the past several years has been greater than at any previous time and that there does not appear to be any slackening in activity or interest.

Jan 12, 1963

By W. L. Phillips

Stress-train curves were obtained for single crystals of silver, Ag-5 pct Zn, Ag-10 pct Zn, and Ag-20 pct Zn tested in tension and shear at 78°, 195°, and 297°K. At room temperature the critical resolced shear stress gC increased, the length of' the easy-glide region increased, and the rate of' work hardening dwving easy glide decreased with increasixg zinc concentration. The change in the ratio of uc at room temperature to that at lower temperatures was significantly greater for the alloys than for pure silver. It was found that an increment in stress was necessary to continue slip when the slip direction was rotated 60 deg. The magnitude of this increment increased with strain for all alloys, increased with zinc concentration for a given strain, and for a given strain increased with decreasing -temperature. DESPITE its practical importance in improving the mechanical properties, alloying is not fully understood. Except for copper alloys few sets of systematic data are available. Von Goler and Sachs' studied the deformation of Cu-Zn alloys of increasing zinc content and found that, for dilute alloys, the critical resolved shear stress increases linearly with concentration. The range of easy glide was found to increase with increasing zinc content. Schmid and seliger,2 Sachs and Weerts,3 and Osswald4 have shown that with Mg-A1, Au-Ag, and Cu-Ni crystals, respectively, the critical resolved shear stress also varies linearly with concentration. More recently, Linde and his coworkers have investigated the variation of the critical shear stress of copper alloyed with tin , antimony, indium, germanium, silicon, nickel, and gold. They found that the slope of the critical resolved shear stress is related to the change of lattice parameter with composition, and also to the difference in Goldschmidt's atomic diameter between solvent and solute atoms. Garstone, Honey-combe, and creetham6 have shown that similar relationships can be found for small additions of silver, gold, and germanium to pure copper. They found that, with increasing silver or gold concentration, the critical shear stress for glide is increased by alloying, and so is the range of easy glide, which reaches as much as 60 pct for 0.50 pct Ag alloy and 0.62 pct Au alloy, as compared to 6 pct for pure copper of similar initial orientation. They also found that the alloying additions had little effect on the rate of hardening during easy glide, the slope scarcely changing with increasing alloy content. General secondary slip was detected only when the crystals began to harden rapidly. Although the slip appeared to be very fine in the early stages of deformation, coarser slip bands were formed towards the end of the extensive easy-glide range. The present investigation describes the deformation characteristics of single crystals of Ag-Zn containing different concentrations of zinc. Tension and shear testing were used for this study. EXPERIMENTAL PROCEDURE The method of growing the single crystals, sample preparation, and method of testing have been described in detail previously.' EXPERIMENTAL RESULTS A) Tension-Room Temperature. The initial orientations and stress-strain curves of single crystals of silver, Ag-10.0 pct Zn, and Ag-20.0 pct Zn are shown in Fig. 1. It is evident that there is considerable change in the stress-strain characteristics as a function of zinc concentration. The effects of zinc concentration on the critical resolved shear stress for both CU-zn8 and Ag-Zn alloys are summarized in Fig. 2. At all concentrations the resolved shear stress of the Cu-Zn alloys is higher than that of the Ag-Zn alloys. The resolved shear stress increases parabolically as a function of composition for both alloy systems. The length of easy-glide region increased with increasing zinc concentration, Fig. 3b). As the length increased the slope (do/de) decreased slightly, Fig. 3(b). Metallographic investigations demonstrated two significant effects of increasing zinc concentration. First, the amount of clustering increased, compare Figs. 4(a) and (b). The slip lines changed from uniform in pure silver to clustered in the Ag-20 pct Zn and Ag-30 pct Zn alloys. Second, the amount of cross slip decreased as the amount of clustering decreased.

Jan 1, 1968

By R. S. Wagner, R. G. Treuting, W. C. Ellis

Use of the Weisseizbevg goniometer for the study of the morphology of whisker crystals and transfer of the results to a stereograplzic projection are described. While in almost all instances a complete and rapid solution is obtained with a purely gaphical treatment, an absolute analytical treatment applicable to difficult cases is given. Examples are given for determination of growth direction and external features of a crystal, for detection of 'twintzittg, and for establislting the orientation relntionships in a kinked whisker crystal. We give here a method for the use of the Weissen-berg goniometerl" in the study of orientation relationships in "whisker" (micro) crystals3-8 and direct transference of the data to the stereographic projection. The operations are straightforward and require no involved calculations: in almost all cases solely graphical treatment is adequate. In a few complex instances, a more exact analytic method may be required. In the method, not only are equatorial reflections of an oscillation photograph used, but also those on higher layer lines, or those not occurring on a recognized layer line. Such reflections off the zero level are often essentialy to detect the presence of twinning. The method is particularly suitable for examination of whisker crystals since the axial or growth direction is almost always one of high symmetry, permitting a more restricted oscillation range to obtain the necessary reflections and an accordingly shorter exposure time. The method is also applicable when there is no lattice-related external symmetry, and is as well able to identify external crystal surfaces, when such exist, with the aid of an optical beam. Thus growth direction, identification of lateral faces, twinning, and orientation relationships in a kinked crystal can be established. A test for the Eshelby twist6-8 can readily be made. The method can be used for orientation, for structure analysis, and as an aid in the identification of an unknown crystal. Moving-film techniques have previously been employed variously for crystal-orientation studies.1,2,9-13 In particular, use of the Weissenberg method for orientation determination has been reported by Wooster and wooster.14 While their method derives the same data as here described, it differs in depending on the tracing of constant p streaks, a less than dependable phenomenon with small specimens, a few microns or less in cross section. The Laue method can and has been used for orientation studies of microcrystals,15 e.g., 2 p in cross section, but requires the extreme intensity and concentration from a microfocus tube to obtain reasonable exposure time. PRINCIPLES OF THE PRESENT METHOD Consider a crystal of random orientation with respect to the oscillation axis in a Weissenberg goniometer. Its diffraction pattern need not necessarily result in recognizable layer lines. In Fig. 1, a stereo-graphic projection of the reference sphere is given with the equatorial plane XZ normal to the oscillation axis Y, and the X-ray beam directed from X towards 2. The great circle ZZ is then normal to the beam, and the axes are right-handed. Thus the reflected X-ray beam lies at the intersection R of small circle ARB of radius 28 from 2, and of small circle RE of radius a from the rotation axis Y. a is the conventional semiapex angle of a cone of diffracted rays from the atoms aligned in the direction

Jan 1, 1967

By R. E. Cech, T. D. Tiemann

It has been shown that hydrogen may be made to serve as a rapid and eflicient reducing agent for Cu, Ni, Co, and Fe sulfides if a scavenging agent for hydrogen sulfide is intimately mixed with the sulfide particles being reduced. Accelerated reduction kinetics are demonstrated for nickel sulfide. Copper, nickel, and cobalt sulfides, when treated at certain temperatures in a combined reducing agent-scavenging agent system, are converted to voluminous masses of fibrous metal product. Studies have been carried out to determine the conditions which lead, on the one hand, to irregular poly crystalline fibers and, on the other, to long single crystal filaments a few microns in diameter. A mechanism is proposed to account for the formation of single crystal filuments. The sulfide minerals of Cu, Ni, Co, and Fe are an important source of these metals yet there has been comparatively little scientific effort devoted towards understanding reduction mechanisms of these minerals. This may be, in part, due to the fact that the most convenient reducing agents for carrying out such studies, viz., hydrogen and carbon, do not react appreciably with sulfides. We have found that the reaction of hydrogen with metal sulfides can be markedly accelerated by placing a scavenging agent for hydrogen sulfide in close proximity to the metal sulfide. A brief series of experiments demonstrating relative reduction rates is reported in this paper to illustrate the effect. With the reduction process thus accelerated we have observed an unusual type of reduction behavior on some of the sulfides investigated. Under certain conditions the metallic product of the reduction reaction takes the form of filaments growing outward from the sulfide particles. The present paper deals largely with efforts to classify the various types of growth forms observed. This study has shown that filamentary growths from sulfides take a much greater variety of forms than has heretofore been reported by Ercker,1 Hardy,2 and Nabarro and Jackson3 in their reviews of metallic growths from copper and silver sulfides. THERMODYNAMIC CONSIDERATIONS The thermodynamics for hydrogen reduction of metal sulfides is quite unfavorable. For the sulfides considered here equilibrium constants typically range from 10-3 to 10-5. These low equilibrium constants impose severe kinetic limitations on reduction since hydrogen sulfide must be transported out of the system at concentrations of only a few hundred ppm. Unless extremely high gas flow rates are employed the atmosphere surrounding any sulfide particle will always be essentially in equilibrium with the sulfide. If, however, one places an efficient scavenging agent for hydrogen sulfide in close proximity to the metal sulfide particles the concentration of H2S near the metal sulfide will be held to a very low value. This would permit the reduction reaction to proceed with little or no inhibition from a buildup of reaction product gas. It is well known that calcium oxide is capable of removing hydrogen sulfide from a hydrogen gas stream of low dew point.4 If a sufficient quantity of calcium oxide is mixed with the metal sulfide particles the reaction: CaO+H2S=CaS+ H2O [l] will substitute moisture in place of hydrogen sulfide in the gas stream and this will not affect, in a direct manner, the reaction: MeS +H2=Me + H2S [2] A convenient method of considering the thermodynamics of the combined reducing agent-scavenging agent system is to consider the atmosphere when the partial pressure of hydrogen sulfide is the same over both the metal sulfide and the scavenging agent, i.e., pH2S (1) =pH2S (2). As a consequence: pH2O (1) pH2(2) =K1K2 The chemical driving force for reduction will depend inversely upon the moisture content of the gas and will be 0 when, in the system, pH2O = pH2.K1K2. Table I lists values of the equilibrium constants for reduction and H2S scavenging reactions for a number of sulfides at several temperatures. Data are taken from Rosenqvist4,5 and Kelly.6 The equilibrium constant products calculated from this data show that the limiting level of gaseous reaction product has been increased by a factor of 10' to l04 as a result of substituting a reducing agent-scavenging agent system for a simple reducing agent system. One possible side effect which must be considered is the possibility that the moisture evolved in the scavenging reaction might cause the atmosphere in the system to be sufficiently oxidizing to favor the formation of oxide rather than metal. This possibility was examined by comparing the equilibrium constant products listed in Table I with equilibrium constants for hydrogen reduction of the respective metal oxides. It was found that for copper, nickel, and cobalt the combined reduction-scavenging reactions could not develop a sufficiently high oxidizing potential in the

Jan 1, 1970

* A complete magnetic picture of the Mesabi range is now available for the first time with the release of 21 additional maps based on the aeromagnetic survey of 30,000 square miles made jointly by the USGS and the Minnesota Geological Survey. A potential iron formation with a magnetic pattern remarkably like that of the Mesabi iron range lies buried beneath the glacial drift in a wide belt extending some 30 miles across the northwest corner of Itasca County in north central Minnesota. Identification of three new uranium minerals by the USGS was recently announced. The new minerals, andersonite, swartzite, and bayleyite are, respectively, hydrous uranyl carbonates of magnesium, of sodium and calcium, and of calcium and magnesium. They were first observed by Charles A. Anderson, Survey geologist, in a coating on gypsum on the 300-ft level of the Hillside mine, Yavapai County, Arizona. International Minerals and Chemical Corp. has announced a $4,000,000 expansion and development program in the Polk County phosphate fields in Florida, Plants for the manufacture of multiple superphosphate and phosphate chemicals including dicalcium p osphate for animal feed and chemical purposes, and a sulphuric acid are planned. Office building, machine shop, warehouse, and laboratory are also scheduled for erection. A new type of tramp iron detector is being used on the conveyor belt feeder at the South Agnew stripping operation. It is made of an alloy of aluminum, nickel and cobalt and does not have any electric coils. The alloy, known as Alnico, is remarkable for the permanence and intensity of the magnetism which it retains. The detector was made by Dings Magnetic Separator Co. and it is probable that Alnico will be used in magnetic separators. The American Society of Engineering Education estimates that unless the percentage of high school graduates entering engineering colleges is increased, there is a strong possibility that instead of a large surplus of engineering graduates, which has been propehsied rather widely, there will soon be fewer engineering graduates available than are needed annually by our national economy. This conclusion is reached from a survey that shows that engineering enrollments are only slightly higher than prewar whereas industrial expansion is increasing the need for engineers. * The natural resources of Korea are being investigated under ECA sponsorship. E.J. Longyear has just embarked 8 crews for that country; two drills are scheduled for base metal search while six are slated for development of coal reserves. An innovation in the development work in the iron country has been the adoption of the Drill-Mobile, jumbo-mounted drills on rubber-tired carriage, by Cleveland-Cliffs at the Mather A and B mines. The machine is being used to cut stations in the new Mathed B shaft and for driving development headings at the Mather A.

Jan 5, 1950

By D. Atkinson, C. Bodsworth, I. M. Davidson

A geometric model of interstitial solid solutions, which has been used previously as a basis for the prediction of carbon activities in Fe-C austenite, is shown to serve also for the calculation of nitrogen activities in Fe-N austenite. The model has been developed to enable predictions to be made of the activities of an interstitial element in the presence of two host atom species. The activities calculated via the model are shown to be in satisfactory agreement with the measured values in the austenite phase for carbon in Fe-C-Co, Fe-C-Cr, Fe-C-Ni, Fe-C-~n, Fe-C-Si, and Fe-C-V alloys and for nitrogen in Fe-N-Ni alloys. The effect of the second substitu-tional solute on the logarithm of the activity of the interstitial element is expressed as the product of a constant mad the atomic concentration of that solute. The constants so derived we related to the thermo-dynamic interaction coefficients which describe the effect on the activity coefficient of carbon of an added solute element. In recent years the thermodynamic activities of carbon and nitrogen in the single-phase austenite field have been determined for iron binary alloys and for several iron-base ternary alloys. In order to extend the use of these measurements, it is desirable to be able to predict with reasonable accuracy the activities of the interstitials at compositions and temperatures other than those which have been measured experimentally. In all the systems studied to date, the interstitial elements do not conform to ideal behavior. Hence, the available data cannot be extrapolated or interpolated using the simple thermodynamic concepts of solutions. Several models have, therefore, been formulated for the purpose of predicting the activity of an interstitial element in the presence of one species of host atom. These models can be divided into the geometric1"5 and energetic6-' types. The former group is based on the assumption that at low concentrations the activity of the interstitial species is determined by a composition-dependent configurational entropy term and an excess free-energy term which is temperature-dependent but independent of composition. The purpose of this paper is to show that the treatment, based on a geometric model, can be extended to enable predictions to be made of interstitial activities in the presence of two substitutional host atom species. THE CONFIGURATIONAL ENTROPY OF MIXING ICaufman5 has shown that the configurational entropy, S,, for a binary solution comprising of a host atom species, A, and an interstitial species, I, can be expressed as: where NI is the atom fraction of the interstitial species, R is the gas constant, and (2 - 1) is the number of interstitial sites excluded from occupancy by the strain field around each added interstitial atom. The number of interstitial sites per host atom, p, is unityg for the fcc austenite solutions considered here. The configurational entropy of mixing for a ternary solution comprising two substitutional atom species, A and B, and one interstitial species, I, can be derived similarly. Let the number of atoms per mole of each of these species in the solution be represented by «a, ng, and nI. From geometric considerations, it is improbable that the addition of a few atom percent of a second host atom species will change the type of sites (i.e., octahedral) in which the interstitial atom can be accommodated in the austenite lattice. At higher concentrations (determined largely by the relative atomic radii of the atomic species present and any tendency to nonrandom occupancy of the host lattice sites) other types of interstitial sites may become energetically favorable. Restricting consideration to compositions below this limit, for 1 = 1 the number of suitable interstitial sites is given by (n + nB). However, if each interstitial atom excludes from occupancy (Z - 1) additional sites, the total number of sites available for occupation is reduced to (n + ng)/Z. The number of vacant interstitial sites is given by: The total number of recognizable permutations of the atoms must include the recognizable, different configurations of the A and B atoms on the host lattice. Assuming that these arrangements are purely random, and are not affected by the presence of the interstitial species, the total number of recognizable permutations in the ternary alloy is given by: The configurational entropy is obtained by expanding, using Stirling's approximation, and collecting like items, as:

Jan 1, 1969

By John R. Caldon

INTRODUCTION Leasing has become a major industry in many countries because of the advantages it affords. Whilst the accounting, legal and tax treatment of leasing varies from country to country, there is far more similarity than difference. The general approach to the subject is largely the same. This paper looks to the basic financial considerations in the decision to lease or buy. TYPES OF LEASES Before embarking upon the subject, it would seem appropriate to define a "lease". A lease may be defined as: "an agreement granting one party the right to use, for a specified period of time, property owned by another party in return for a series of payments of rental by the user to the owner''. Ownership, of course, generally entitles the owner to unrestricted use of the asset over its useful life in contrast to a lease which gives the lessee use over a limited period. The distinction between the status of owner and a lessee often is fairly small. In this case we are dealing with what is generally termed a "finance lease". A finance lease is one which substantially transfers the risks and benefits of ownership from the legal owner to the lessee. For example, a finance lease would exist where the lessee enters into a lease of an asset for most of its useful life and has an option to buy the asset at the end of the lease for a price which takes cognisance of the rentals already paid. Where a lease does not substantially transfer the benefits and risks of ownership to the lessee, i.e. those benefits and risks remain with the owner and lessor, the lease is termed an "operating lease" and is an agreement for the renting and usage by the lessee of an asset owned by the lessor for a limited period. An example of an operating lease might be where a tenant leases a building for a defined period say 6 years with the rent and occupancy subject to renegotiation at the end of the lease term. The economic consequences of the distinction between a finance and an operating lease is very important. With a finance lease, the lessee has a de facto economic interest in the asset and the alternative to a finance lease is some form of purchase; with an operating lease, the lessee does not have a basic economic interest in the asset and consequently a comparison with a purchase option involves far more than simply a funding comparison. Some of the principal differences between finance and operating leases can be summarised as follows: (a) finance leases: -the risks and benefits of ownership are substantially transferred to the lessee; -the lessor normally recovers his investment during the term of the lease; -the lessor in entering into the transaction is relying more on the creditworthiness of the lessee than the underlying value of the asset; - the lease is either non-cancellable or a large penalty will apply for unilateral cancellation by the lessee; (b) operating leases -the risks and benefits of ownership remain essentially with the lessor; -the lease rental income would not normally cover the recovery of the lessor's investment; -the lessor evaluates his risk in terms of the underlying value of the assets;

Jan 1, 1985

By B. F. Buie

For over 200 years meerschaum has been a significant item of trade between the Near East and countries to the west. Best-known for its use in making smoking pipes and cigar and cigarette holders, it is also used in making a variety of decorative and ornamental items. It is easily carved, and is given an attractive, lustrous finish by rubbing. No published specifications are known, but compact form, purity, uniform whiteness or light color, and uniform, porous texture appear to be requisites. Fig. I a shows the appearance of a piece of crude meerschaum from Turkey; Fig. lb a carved item; and Fig. lc, d, and e show the fibrous and porous texture as revealed by the scanning electron microscope. Neither a major industrial mineral nor a precious stone, meerschaum nevertheless holds a record of long-and continuing-association with art and personal affairs of man. It is also a mineral to which modem methods of exploration and production probably could be profitably applied. An interesting account of the preparation and use of meerschaum in the early part of this century is given by Sterrett (1907). Geology and Mining Mineralogy Meerschaum is recognized now to be the compact variety of sepiolite, the claylike variety of which is one of the minerals included in the chapter on clays. The word meerschaum, from the German meaning "sea foam," was in earlier times used synonymously with sepiolite, a word of Greek origin suggestive of the resemblance of the compact variety-then the only variety known-to cuttlefish bone. At one time meerschaum was used as the commercial name, and sepiolite for the scientific name. However, to think of meerschaum as the name by which sepiolite is known commercially is no longer valid, in view of the recent emergence of the earthy variety as a competitor of bentonite and other clay materials. Present tendency is to restrict the term meerschaum to the compact variety, and to use the term sepiolite as a more general name to include both the compact and earthy varieties. This is the terminology followed in this publication. Meerschaum typically is white to light gray, has a hardness of 2 to 2 ½ , conchoidal to irregular fracture, and specific gravity varying with porosity from about 2 to less than 1. The composition is somewhat variable,- but is near that determined by Schaller (1936) for sepiolite as 2MgO.3SiO2.4H2O. A more modern for mula based on X-ray determination of the crystal structure is given by Caillére and Henin (1961) as (Site) (Mg9)030(OH)6(0H2)46H20. The reason for the firm, compact nature of meerschaum, in contrast with the earthy variety of sepiolite, is not fully understood. It may be due to the presence of a very minor amount of some bonding material such as silica. Scanning electron microscope (SEM) photographs of a specimen from Turkey (Figs. lc-le) indicate that the meerschaum is composed predominantly, if not entirely, of crystalline fibers which merge into sheetlike forms in a complex, intertwined mass. Detailed X-ray and crystal structure data, as well as some data on thermal stability range, are given by Caillère and Hénin (1961) for the sepiolite family of minerals. Mode of Occurrence and Origin Most authors have attributed the origin of meerschaum to alteration of serpentine or other magnesian minerals. The occurrence in alluvium and other surficial deposits does not necessarily indicate that the alteration was supergene. In fact, hydrothermal origin appears more likely for some deposits, though not for all.

Jan 1, 1983

By J Price, M. R. Geer, H. F. Yancey

COAL mine operators recognize coal as an abrasive material, because the wear of drilling, cutting, and conveying equipment is reflected as a cost item for replacement of parts. Similarly, industrial consumers of coal experience abrasive wear on all coal-handling equipment. Operators of pulverized fuel plants are doubtless most keenly aware of the abrasiveness of coal, because under the high contact pressures developed between coal and metal in pulverizers, abrasive wear is increased many fold. Moreover, experience in operating pulverized fuel plants has demonstrated that some coals are much more abrasive than others. Hardgrove' stated that maintenance costs entailed by the wear of grinding elements is often a more important variable than the cost of the power required to pulverize different coals. Craig2 also reports that one coal may cause pulverizer parts to wear several times faster than another. It is apparent, therefore, that those concerned with pulverizing coal could profitably employ a method for estimating the abrasiveness of different coals, just as they utilize standard tests for thermal value, grindability, and ash-fusion temperature to assist in selecting the most suitable and economical coal to use in a particular plant. The objective of this investigation was to develop a test procedure that would be suitable for general use in estimating the abrasiveness of coals. However, few, if any, of the standard tests now used for evaluating the properties of coal are the product of a single investigation or the result of a single investigator's efforts. Rather, in each case, a testing procedure was devised by one investigator, used by others on a wider variety of coals, and finally refined completely as the result of the joint efforts of a number of interested people. Thus, the test procedure for estimating abrasiveness developed in the course of this work may not be refined sufficiently in its present form for general use, but it may serve as the starting point from which an acceptable test procedure can be developed. The method has been used thus far on only about a dozen coals, and there has been no opportunity to attempt a correlation between experimental results and actual plant experience. Only wider use of the procedure by other investigators and correlation with plant experience can determine to what extent the method will have to be modified to render it suitable for general application. Test Method Although the literature contains no record of an attempt to devise a method for estimating the abrasiveness of coal that could be used industrially, several investigators have tested properties of coal that are closely related to its abrasiveness. The abrasiveness of a material generally is considered to be related to its hardness, and hardness tests for coal have been employed by Heywood,' O'Neill," and Mathes. Also, the resistance of coal to abrasion, a property that presumably is related to the abrasiveness of coal, was measured by Heywooda and by Simek, Pulkrabek, and Coufalik.2 11 these investigators tested only individual pieces of coal. Since coal is a heterogeneous material having components of varying properties, tests of this type can yield results having little more than academic interest. Only a test method that utilizes a representative sample of coal can give results that are useful industrially. The abrasion tests used for various other materials have been considered for adaptation to testing the abrasiveness of coal. The tests used for metals,7-9 paving and flooring,'" and rubber," cannot be used because coal is not sufficiently abrasive.~ The present experimental work was begun before World War II and was conducted by three research fellows"'" working under a joint agreement between the University of Washington and the Bureau of Mines. After a great deal of preliminary work with a variety of apparatus and materials, a test procedure was developed which consisted of rotating a test disk 2Yz in. diam in a steel mortar containing the coal sample. The shaft carrying the test disk at the lower end and a 100-lb load on the upper end was free to move vertically. The bed of coal in the mortar was kept fluid by low-pressure air admitted through a port near the bottom of the mortar. Measurable wear on an Armco iron disk could be obtained in this test procedure, but, despite extensive efforts to eliminate them, several major disadvantages remained in this test method. First, with most coals the amount of wear on the iron disk did not exceed a few milligrams. Second, a single type of disk was not applicable for all coals. A smooth iron disk gave satisfactory results with both bituminous and sub-bituminous coals, but hardly any wear with anthracite or coke. A disk having studs or projections gave more satisfactory abrasion losses with anthracite and coke and presented no operating difficulties with free-burning bituminous and sub-bituminous coals. It could not, however, be used with caking coals because these coals formed a

Jan 1, 1952

By R. C. Palmer

The testing of flotation oils has occupied a large part of the time of the testing departments of various companies using the flotation process in the beneficiation of their ores. The great differences in ores and in oils has made such work necessary, as it has not been possible to select the oil best suited for the purpose without trial of many kinds. In fact, individual shipments of flotation oils from the same manufacturer will often differ so radically that the mill men have been forced to test every lot of flotation oil before its use in the mills. Further, although almost every imaginable product of the distillation of wood, from alcohol to pitch, has been tested in a more or less perfunctory manner by various people, few companies have allowed the results of their tests to be made public. This work was undertaken for the purpose of obtaining reliable data regarding the value as flotation agents of a number of products that are obtained from the distillation of wood by different methods, and incidentally to determine whether some of the products not used at present could be used. Large quantities of such materials are being masted or burned in the wood-distillation plants of the United States, and if some use other than fuel could be found for these materials, such a use would represent a distinct saving to the country as a whole, would increase the profit of wood-distilling plants now operating and perhaps make it possible for others to operate which at present cannot do so except at a loss. At the same time it was thought that if such products can be used as flotation agents, then their use would serve to increase the number of oils and other products available for flotation purposes. It was also hoped that it might be possible to discover a substitute for some of the most effective but comparatively high-priced oils which are now used for flotation

Jan 1, 1917

By Orr Hamilton

VALUATION of a mine is an approximation of its true cash value which requires the application of fundamental principles of economics. Mines are valued from necessity, for the following reasons: (a) Transfers of titles. (b) Dissolutions of partnerships or corporations. (c) Mergers of mining companies. (d) Appraisals for the purpose of State and Federal taxation. (e) Establishment of the fact of worth as a basis of loans. (f) Determination of values as frequently required in litigation. (g) Listing of stock for sale by a reputable stock exchange. For the majority of purposes a valuation is required as at the present time, but for some purposes valuations as of bygone times may more nearly reflect the intrinsic worth of a mine because its subsequent history can never be, entirely ignored, but valuations made as at the present time are better indicators of cash values. Many mines with great intrinsic worth have been sold for small cash prices. The object of legitimate mine valuations is to deter-mine salable value, or that price in cash at which a transfer of the property from a willing seller to a willing buyer might be consummated, assuming that both vendor and vendee have knowledge of all pertinent data and that the owner, is not forced to sell at a sacri-fice-the definitions of fair market value precluding a forced sale.

Jan 11, 1923

By E. J. Harris

Mathematical solutions to complex mine ventilation problems are possible, but often the airway network is so complex that the mathematical solution becomes tedious and impractical. A fluid network analyzer, designed and built for analyzing mine ventilation problems has been in service at the Bureau of Mines' Pittsburgh station for approximately nine years. Using this analogue as a model, the mine ventilation network is simulated electrically by a combination of series and parallel circruits laid out to conform with actual mine airways. A tungsten filament lamp, referred to as a Fluistor, is used to simulate mine airway resistance. With the analogue ventilation model established, voltages of the proper amplitude to represent ventilating pressures are impressed across the circuit at points where mine fans and airshafts are located. Comparison of mathematical solutions of complex systems against analogue results showed a maximum variance of 3% for pressures and 2% for quantities. An electrical fluid network analyzer, designed and built especially for analyzing mine ventilation distribution problems, has been in service at the Bureau of Mines, Pittsburgh, for approximately nine years. It is a nonlinear, low voltage, fluid network analyzer of the type developed by the late Malcolm S. McIlroy, Professor of Electrical Engineering, Cornell University, who cooperated with G. E. McElroy, of the Bureau of Mines, in adapting the instrument to mine ventilation systems. Several modifications have been made since the original installation, but a considerable part of this paper is drawn from G. E. McElroy's original description of the analogue.' The analysis of water or gas distribution systems2,3 led to the development of this type of network analyzer. Several similar units are now employed by utility companies for this purpose; however, the Bureau of Mines unit is the only one designed specifically for mine airflow problems. Other airflow analogues employing a similar principle have been used at the Central Research Station of the Netherlands State Mines,4 in England,5 and in South Africa.6 Information on these devices indicated they were somewhat inflexible because commercial lamps with a sufficient range of resistance are difficult to obtain. Computers for mine ventilation analysis have been developed in Germany which instead of lamps use a variable resistance to adjust for turbulent flow laws. These units are expensive, but excellent results have been reported in their application. THE ANALYZER Theory of Application: As airflow generally follows the law of turbulent fluid flow, resistance to flow is nonlinear; consequently, the problem has been to find a nonlinear resistance element of suitable range that can be used for electrically simulated airflow. Tungsten filament lamps operated on alternating or direct current approximate the square-law resistance characteristics of mine airflow over a large range below maximum or rated voltage; that is, the voltage drop varies approximately as the square of the current. Consequently, the heart of the network analyzer is a nonlinear resistor known as a Fluistor, which is simply a custom-made low voltage, tungsten filament lamp that is available in a progressive series of relative resistance values ranging from 0.05 to 500 in nominal 5% steps. However, variations in manufacturing large groups result in differences of 1 to 3%, but series arrangements required for high-loss branches can be matched within about 1%. Utilizing a combination of Fluistors and load circuits, the mine ventilation system is duplicated electrically. Intake load circuits are connected from power intake to primary points of the circuit network; segments of unregulated flow along intakes and returns are represented by Fluistors, regulated splits and leakage paths are represented by load circuits and Fluistors of proper capacity; and mine exhausts are connected to ground from the last point of the network to complete the circuit. For the special purpose of representing booster fans or natural draft conditions, boosters or separate source circuits are provided that can be inserted between any two points of a network to increase voltage to the required value. Physical Layout: The analyzer consists of three 42

Jan 1, 1963

By D. E. Furman

The thermal coefficients of linear expansion for several stainless steels have been determined over the temperature range from —300° to 1000°F. The steels studied include types 301, 304, 316, 347, 310 and 330. This wide selection of compositions allows an insight into the effects of austenite stability and alloy content on the expansion characteristics. THE recent increased use of materials in low temperature applications has created a field for which the properties of austenitic iron, chromium, nickel alloys are particularly suited. Tensile and impact values of stainless steels at subzero temperatures have been made available in the technical literature but, as yet, little information has been published with respect to expansion characteristics. In order to supply this need, a study was made of several of the more common compositions. Those selected were types 301, 304, 316, 347, 310 and 330 stainless steel. Both the mean and instantaneous coefficients of linear expansion were determined over the temperature range from —300°F to 1000°F. Procedure The materials used were commercial grades with the exception of type 301 which was made in a 10# high frequency furnace. The compositions are listed in table I. All steels were given an anneal at 1950°F for 30 min and water quenched prior to machining the expansion specimens. Expansion readings were taken on specimens 0.250 in. in diam by 4.000 in. long with a fused quartz tube expansion apparatus similar to that described by Hidnert and Souder.1 Temperature measurements were made with a chromel-alurnel thermocouple calibrated for use at subzero temperatures. A bath of propane was used for temperatures from —300° to —100°F and one of alcohol from —100°F to room temperature. These baths were contained in large mouthed Dewar flasks and cooled to the desired temperature levels by passing liquid nitrogen through glass cooling coils placed in the flasks. The baths were stirred constantly for temperature equalization and were heated by immersing metal rods which were replaced frequently enough to give a heating rate of approximately 150°F per hr. A resistance wound furnace was used for heating from room temperature to 1000°F and throughout this range rates of about 450°F per hr were maintained. The furnace was designed so that the temperature gradient over the specimen was within 5°F. In most instances, the expansion readings were taken during heating from —300° to +300°F at

Jan 1, 1951

By F. R. Scauzillo

Equilibrium data which should be useful in the design and/or evaluation of glycol dehydration units were prepared from an analysis of various published data and the correlation of these data by the use of the thermo-dynamic equilibrium ratio. The equilibrium ratios of water are used to solve the glycol absorber problem; such solutions are necessary to define the number of trays and the glycol circulation rate needed to meet drying requirements. Activity coefficients were obtained which relate directly to the equilibrium ratios of water in the water-TEG-natural gas system. These activity coefficients have been used to calculate the equilibrium dew points for aqueous TEG concentrations of 60 to 99.9 weight per cent for the temperature range of 40° to 120° F. They also provide a means of calculating equilibrium ratios for water in the water-TEG-natural gas system; this applies to any desired TEG concentration and to the temperature range from 40° to 120°F. INTRODUCTION During the last several years, the drying of natural gas with aqueous triethylene-glycol (TEG) solutions has become very prominent. Most users of TEG as a drying agent have been satisfied with the performance of TEG solutions at the conditions used; however, there always has been some discussion of the drying ability of TEG solutions at conditions not commonly encountered such as temperatures below 50° or 60°F, but more particularly temperatures above 100°F, and pressures above 1,000 psia. Today, when higher wellhead temperatures such as 120°F are more commonly encountered many are skeptical of TEG's ability to dry sufficiently well to provide dew points around 32°F, which is generally the maximum tolerable when attempting to dry a gas to contract specifications of 7 Ib/MMscf. These views probably have evolved to some extent from the days when suppliers would not guarantee dew-point depressions in excess of 65° to 75 °OF. Also, the feelings about TEG drying may have arisen from the lack of information about the equilibrium relation of water in the drying operations. Porter and Reid' have reported equilibrium data for a 95 per cent TEG solution, while Townsend2 reported equilibrium data for 95, 98 and 100 per cent TEG solutions. Townsend also presented a calculational method which obtains activity coefficients in the liquid phase and, subsequently, the equilibrium water content of a saturated gas over glycol from published3 atmospheric dew points. Wise, Puck and Failey' presented activity data for the water-TEG system at atmospheric pressure. In the past, the equilibrium ratios published for water in a 95 per cent by weight aqueous TEG solution have been used indiscriminately by many for all concentrations of TEG encountered in gas drying operations. Since essentially all such gas operations require the use of more concentrated TEG solutions, a study was undertaken to correlate the existing equilibrium data for aqueous TEG and gas systems and to provide some means of calculating the equilibrium ratio of water in the natural gas-water-TEG system where TEG concentrations were other than 95 per cent. The data presented herein consider only the equilibrium drying ability of the TEG solutions and do not consider the effect of temperature and pressure on the tray eficiency of contactors. In other words, this paper is concerned primarily with the development of the equilibrium relationship between water in the dried natural gas and the water in the lean TEG entering the top tray of the absorber. BASIC EQUILIBRIUM RELATIONS A relationship which relates the K value of water in the natural gas-water-TEG system to the vapor pressure of water at the system temperature, the total pressure of the system and the activities of the liquid and gas phases has been evaluated. It is well known that, for any component of a mixture at equilibrium between a gas phase and a liquid phase,

THE following nominations for officers in the, Petroleum Division have been made by the nominating committee, of which Alfred G. Heggem was chairman: Chairman, John M. Lovejoy, Vice-pres., Amerada Petroleum Co., Tulsa, Okla.; vice-chairman for Refinery Engineering, Walter Miller, Vice-pres., Marland Refining Co., Ponca City, Okla.; vice-chairman for Production En-gineering, M. E. Lombardi, Vice-pres., Pacific Oil Co., San Francisco, Cal.; associate vice-chairmen for Produc-tion Engineering, T. E. Swigart, Prod. Engr., Shell Co. of Cal., Los Angeles, Cal.; Joseph B. Umpleby, Vice-pres., Goldelline Oil Corp., Oklahoma City, Okla.; vice-chairman for Production, W. E. Wrather, Cons. Geol., Dallas, Texas; associate vice-chairman for Production, Joseph Jensen, Associated Oil Co., Los Angeles, Cal.; vice-chairman for Transportation Engineering, E. P. Bly, Engr., Pipe Line Dept., Standard of California, San Francisco, Cal..; vice-chairman for Economics., Joseph E. Pogue, Cons. Geol., New York City. The election will take place, at the annual meeting of the Division in New York in February. Any independent nominations received before Jan. 20 and endorsed by ten members, will be announced in MINING AND METALLURGY for February and placed before the meeting for considera-tion. Extensive plans are being made for the meeting and a large number of excellent technical papers have already been received.

Jan 1, 1927

By D. E. Coates, G. R. Purdy, S. V. Subramanian

The morphological stability of the planar solid-liquid interface in dilute ternary alloys, undergoing steady-state unidirectional solidification, is analyzed in terms of both the constitutional supercooling principle and the perturbation methods recently developed by Mullins and Sekerka. First, various steady-state solutions for the two solute distributions ahead of a planar interface are examined. The nature of the solutions depends on the size and concentration dependence of the off-diagonal diffusion coefficients. W~thin the framework of the constitutional supercooling principle, a cumulative contribution to instability frorn the two solutes is found to exist in the absence of diffusional interaction. It is shown that the latter can produce a further enhancement of instability or can have a stabilizing influence, depending on the form of the liquidus surface and on the sign of the solute-solute interaction. A perturbation analysis, which ignores diffusional interaction, verifies the cumulative influence of lhe solute fields and demonstrates that the Mullins-Sekerka stability criterion for binary systems (with capillarity accounted for) can be readily extended for application to ternary systems. SOME time ago, Tiller et al.' calculated the solute concentration distribution ahead of the planar solid-liquid interface of binary alloys undergoing steady-state unidirectional solidification. An earlier qualitative proposal that the transition from planar to nonplanar growth morphologies is associated solely with the onset of constitutional supercooling in the liquid layer ahead of the moving interface2 was used in conjunction with this calculation to put the now well-known constitutional supercooling (C-S) stability criterion into quantitative terms. Mullins and Sekerka,3 in a recent and very elegant analysis, established a more complete criterion (hereafter referred to as the M-S criterion). Interfacial stability was investigated by determining the time derivative of the amplitude of a sinusoidal perturbation of infinitesimal amplitude which had been introduced into the originally planar shape of the moving interface. Of particular importance is the fact that capillarity was included in the boundary conditions of their calculation. The purpose of the present paper is to extend all of this earlier work on dilute binary systems for application to dilute ternary alloy solidification. The analysis is divided into three sections. In the first the two solute distributions ahead of a moving planar interface are considered. Mathematical solutions are de- termined for situations in which: a) diffusional interaction is negligible, 6) diffusional interaction must be considered but circumstances permit use of constant diffusion coefficients, and c) the concentration dependence of off-diagonal diffusion coefficients can be described by first-order dilute solution approximations. In the next section, a stability criterion analogous to the C-S criterion is developed and the influence of diffusional interaction on interface stability is analyzed. Finally, the perturbation formalism of Mullins and Sekerka, with capillarity included in the boundary conditions, is extended for analysis of ternary systems in which diffusional interaction is negligible. The study of interface stability in binary systems usually commences with the assumption that the equilibrium distribution coefficient and the slope of the liquidus line are constant at values corresponding to infinite dilution. Similar assumptions have not been introduced into the present treatment; that is, we do not assume planar solidus and liquidus surfaces joined by tie lines which yield constant distribution coefficients. The latter involves the assumption of no ther-modynamic interaction between solute species in both the solid and liquid. We consider a ternary phase diagram for which the solidus and liquidus surfaces are, in general, nonplanar and of course pass through the corresponding binary solidus and liquidus lines. These lines are not assumed to have constant slope. In the dilute regions we are concerned with, the following assumptions are made: i) The solidus and liquidus surfaces are of a form such that both the solidus and liquidus temperatures are monotonically varying functions of each solute concentration. ii) The tie lines are such that the equilibrium distribution coefficient of a given solute is greater than unity for every point on the solidus (or liquidus) surface or it is less than unity for every point. STEADY-STATE SOLUTE DISTRIBUTIONS IN THE LIQUID As will be demonstrated in the next section, a knowledge of the steady-state solute profiles is not a necessary prerequisite for the formulation of a ternary C-S stability criterion. However, in that details, such as the complete description of the equilibrium liquidus temperature profile, require an evaluation of the solute distributions, the overall treatment is enhanced if these distributions are determined. Consider a ternary system (solvent plus solutes 1 and 2) for which a planar solid-liquid interface is in unidirectional motion at constant velocity V. At this stage it is unnecessary to limit ourselves to dilute solutions. For a stationary frame of reference the generalized forms of Fick's equations are:

Jan 1, 1969

By Thomas A. Read

The internal friction of single crystals of metals is affected markedly by a variety of factors, which, according to the literature, are without influence on the internal friction of polycrystalline metals at strain amplitudes less than 10-5. For example, the internal friction of a suitably oriented zinc single crystal is multiplied by a factor of ioo when the vibration amplitude is slightly increased, and the internal friction of a copper crystal is markedly increased by the application of a stress of 30 lb. per sq. in. for one minute. In this paper it will be shown that these, together with the other phenomena associated with the damping of mechanical vibrations in metal single crystals, can be satisfactorily explained, at least qualitatively, in terms of an atomic mechanism that has been proposed for quite another purpose—that of accounting for slip in metals. The extraordinary agreement between the observed behavior of the metal single crystals and the behavior that could be predicted on the basis of this atomic mechanism leads to the belief that the latter is probably essentially correct. If this is so, it follows that valuable information about the slip process in metals may be gained from measurements of internal friction on single crystals. In this paper the results of the only study to date on the damping of mechanical vibrations in single crystals of metals mill be presented. Experimental Procedure The internal friction of a material is a measure of the rate at which the energy of mechanical vibrations is converted into heat. The measure of internal friction used in the present paper is the decrcment A, which is defined as the fraction of the energy of vibration lost per half cycle. The measurements described here were made for longitudinal oscillations at a frequency of 33.5 kc. for the copper crystals, and at a frequency of 39 kc. for the zinc crystals. The method used is that of the composite piezoelectric oscillator. The single-crystal specimens are in the form of circular cylinders M in. in diameter and I 1/2 to 21/2 in. long. The crystal rods are waxed in a V-block and sawed to the proper length with a fine jeweler's saw. The ends of the specimen are ground flat, and one end is cemented with a very thin film of beeswax and rosin to the end of an x-cut quartz rod which is 1/4 in. in diameter and 3 in. long. The length of the specimen rod is determined by the condition that its natural frequency for longitudinal vibration be the same as that of the quartz rod, within 0.5 per cent. The lengths of the specimens are thus different for different orientations of the cylinder axis with respect to the crystallographic axes. When the specimen and quartz rods are thus matched in frequency the adhesive is at a node of stress, and it has been shown experimentally that under these circumstances

Jan 1, 1941

By Thomas A. Read

The internal friction of single crystals of metals is affected markedly by a variety of factors, which, according to the literature, are without influence on the internal friction of polycrystalline metals at strain amplitudes less than 10-5. For example, the internal friction of a suitably oriented zinc single crystal is multiplied by a factor of ioo when the vibration amplitude is slightly increased, and the internal friction of a copper crystal is markedly increased by the application of a stress of 30 lb. per sq. in. for one minute. In this paper it will be shown that these, together with the other phenomena associated with the damping of mechanical vibrations in metal single crystals, can be satisfactorily explained, at least qualitatively, in terms of an atomic mechanism that has been proposed for quite another purpose—that of accounting for slip in metals. The extraordinary agreement between the observed behavior of the metal single crystals and the behavior that could be predicted on the basis of this atomic mechanism leads to the belief that the latter is probably essentially correct. If this is so, it follows that valuable information about the slip process in metals may be gained from measurements of internal friction on single crystals. In this paper the results of the only study to date on the damping of mechanical vibrations in single crystals of metals mill be presented. Experimental Procedure The internal friction of a material is a measure of the rate at which the energy of mechanical vibrations is converted into heat. The measure of internal friction used in the present paper is the decrcment A, which is defined as the fraction of the energy of vibration lost per half cycle. The measurements described here were made for longitudinal oscillations at a frequency of 33.5 kc. for the copper crystals, and at a frequency of 39 kc. for the zinc crystals. The method used is that of the composite piezoelectric oscillator. The single-crystal specimens are in the form of circular cylinders M in. in diameter and I 1/2 to 21/2 in. long. The crystal rods are waxed in a V-block and sawed to the proper length with a fine jeweler's saw. The ends of the specimen are ground flat, and one end is cemented with a very thin film of beeswax and rosin to the end of an x-cut quartz rod which is 1/4 in. in diameter and 3 in. long. The length of the specimen rod is determined by the condition that its natural frequency for longitudinal vibration be the same as that of the quartz rod, within 0.5 per cent. The lengths of the specimens are thus different for different orientations of the cylinder axis with respect to the crystallographic axes. When the specimen and quartz rods are thus matched in frequency the adhesive is at a node of stress, and it has been shown experimentally that under these circumstances

Jan 1, 1941

By M. A. Olade

Biotite, magnetite and quartz feldspar separates from rocks around porphyry copper deposits in the Highland Valley have been analyzed for copper, zinc and other related trace and major elements. Results show high copper concentrations in mineral samples close to mineralization, with a strong positive correlation with whole-rock copper contents. Zinc, on the other hand, shows no cleat-cut systematic relationship to mineralization, although there is a subtle decrease in the dues obtained for anomalous biotite samples. Manganese, cobalt and nickel in biotites show similar patterns as zinc. Using a sulfide-selective leach, it is show that the enhanced copper dues in mineral samples proximate to mineralization can be accounted for by the presence of minute inclusions of sulfides. In contrast zinc seems to occur in isomorphous substitution for femic elements, in a form that is leachable by hydrothermal activity. Results also show that copper content of biotite has a positive correlation with the modal proportion of biotites and their iron contents, whereas a negative relationship with manganese is apparent Geochemical contrast for copper between background and anomaly is not better in mineral fractions than whole rocks, consequently the use of minerals as sampling media shows no obvious advantage for mineral exploration purposes in the Highland Valley district.

Jan 9, 1979

By H. F. Dawes

In China all minerals are, theoretically at least, the property of the Emperor, and the Imperial permission must be got from him for the privilege of working them. A direct tax is levied on this privilege, and by simple command, the Emperor can close a mine at any time. Occult geomantic influences are a large factor in determining the opening or the arbitrary closing of a mine. The location with reference to points of the compass, graves and natural objects, may be really or professedly considered as indicating that those influences are favorable or unfavorable. The consequence, is, of course, that for the authorization and encouragement of any considerable enterprise, friends' at court, practical politics, and more or less bribery, are required. As a result, most Chinese mining is illicit, and is carried on in a small way only. Often along a single vein, or over a small section of mining country, a few individuals obtain rights over all the openings, most probably by loaning money to the head-men of the operators and holding the mines as security for the debt. In such cases, perhaps, for better security, all the ore is reduced in the works established by the creditors, who also handle all silver produced..As the head-men are, for the most part, improvident, and the laws and customs for the collection of' debts are stringent and peculiar, the " officemen" or creditors acquire in time what is practically an ownership of

Jan 1, 1892