Search Documents

The income of the Institute is derived mainly from dues, advertising in MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1938

By A. S. Appleton, M. B. Bever

The stored and expended energies of an Au-Ag alloy deformed in torsion were investigated as functions of strain, strain rate, and temperature. At room temperature, the stored energy, measured by tin solution calorimetry, increased linearly up to an intermediate strain, above which it was nearly constant; at 78 °K the relation was linear up to fracture. Approximate values of the energy stored at 4 OK indicate a rapid increase below 78 OK. The energy stored by specimens deformed successively at 4o and 78oK changed slowly with increasing second strain from the curve for energy stored at 4 OK (measured after annealing at 78oK) to that for deformation at 78°K. The ratios of the stored to the expended energy at room temperature and 78 oK were unusually large. The additional amount of energy stored at the lower temperature is attributed mainly to an increase in the number and energy of dislocations. The stored energy as a function of strain rate at 4oK (measured after annealing at 78oK) increased to a sharp maximum over a narrow range of strain rates, whereas the expended energy changed only slightly. These effects are explained by the generation of point defects resulting from the enforced nonconservative movement of jogs in fast moving screw dislocations. The effect of straining successively at two strain rates at 4oK was also investigated. Stress-strain curves for 4o, 78oK, and room temperature and the results of micro examination of specimens deformed at these temperatures are also reported. THIS investigation is a continuation of a research program primarily concerned with the effects of variables on the energy relations involved in the deformation of metals. The variables investigated in earlier work have included strain, strain rate, temperature of deformation (room temperature and 78oK), and the type of deformation process. Most of this work has been carried out with Au-Ag alloys. In the investigation reported here, the deformation process was torsion, which had not been used previously in the program. The stored and expended energies involved in the deformation process were measured as functions of strain, strain rate and the temperature of deformation in the range 4" to 373" K. The microhardness and microstructure of deformed specimens were also investigated. The relation between stored energy and strain differs for different deformation processes.1,2 In general, the stored energy increases with strain and may attain a nearly constant value at large strains. This value and the rate at which it is reached, however, depend on the process of deformation. This dependence has been attributed, at least in part, to differences in the effective strain rate and rise in temperature of the specimen during deformation. The effects of the temperature of deformation on both the stored energy and the energy expended in the working process have been the subject of only a few investigations.3-6 Values of these quantities at low temperatures are of special interest as they yield information on point defects which, for many metals, is not obtainable at higher temperatures. The effect of the strain rate on the stored and expended energies has received little attention The strain rate has usually been measured only in relative terms, and hence the interpretation of its effect on the stored energy has been mainly comparative.

Jan 1, 1963

By W. E. Showalter

This paper discusses some of the results of combstion-drive tests which were made in a test cell using a sand bed 10 in. in diameter x 10-ft long. The test method is illustrated and described. The relationship between the API gravity of the in situ oil and the amount of air required for combustion drive is discussed in detail. Other things constant, the air requirement for combustion drive increases as the APl gravity of the in situ oil decreases. If the test results apply to actual reservoirs, the lowest-priced oils may cost the most to recover by this method. Information is shown which indicates that the effect of pressure on the amount of hydrocarbon burned is not large. A method of predicting air requirements from the API gravity of the in situ oil is presented. INTRODUCTION Combustion drive is the term used to identify the process of interstitial or in situ burning as an oil recovery method. Part of the in situ oil is burned to generate the energy needed to produce the remainder of the oil. Combustion drive as an oil recovery mechanism remains an economic uncertainty in spite of all the work that has been done by the industry in both laboratory and field?-6 This paper will show some of the results of tests which were made in a test cell for the purpose of studying the nature of the combustion-drive process. It will present data which indicate that the API gravity of the in situ oil is a significant indicator of the amount of air required to drive a burning front through oil sand. Air requirement varies inversely as the API gravity of the in situ oil. EXPERIMENTAL The tests were performed in a cell which utilized a cylindrical sand section 10 in. in diameter x 10-ft long. The thin-walled metal pipe which held the sand was wound with twenty external electrical resistance heaters which, by means of an automatic controller, maintained adjacent sections of the wall of the pipe at temperatures equal to the temperatures of the contained sand. Each heater covered 6 linear in. of the pipe. By this means lateral heat loss from the sand section was minimized, thereby causing the sand section to simulate more closely a horizontal increment of a combustion-drive reservoir. Fig. 1 shows a schematic diagram of the test assembly. Thermocouples to measure the temperature in the sand were located every 6 in. along the length of the sand section. The pipe containing the sand was enclosed in a cell designed for an operating pressure of 500 psig. The inlet air pressure was controlled at the inlet, and the gas flow rate was controlled and measured at the outlet of the cell. The oil sand used for the tests was prepared by mixing first water and then oil with the noncon-solidated sand using a closed mixer similar to a cement mixer. Table 1 shows a screen analysis of the sand. Ninety percent of the sand was 100 mesh or finer. This sand was a mixture of 80 per cent No. 120 Nevada White Sand and 20 per cent Tennessee Hi-Fusion Moulding Sand No. 3. The Nevada sand was a clean silica sand. The Tennessee sand con-

By Thorp D. Sawyer

In June 1914, one week before I was to be awarded my sheepskin in upper New York State, I received a telegram from New York City which read "Can offer you position as engineer in Chile at $115 a month contract for one year. (signed) Chile Copper Co." That night, Friday, I took a sleeper to New York and arrived at the Guggenheim Brothers' company office at 165 Broadway, just as it was opening up on Saturday morning. Saturday was no holiday in that era. Presenting the telegram at the office, I was ushered into a sub-executive's office and shown a mimeographed contract which 1) agreed to pay me $115 per month from the date of leaving New York until I returned, and with travelling expenses both ways, 2) fixed a charge of $46 per month for board and lodging in company quarters, and 3) stipulated a contract term of one year with the right to retain my services for another year if the company so elected. While a bit huffed at the year's "kicker" I nevertheless accepted. I was then told to prepare to leave the following Wednesday (June 17) on a United Fruit Co. steamer for Panama. Objecting that I still had to receive my degree on the 17th and had planned a vacation in Ohio for a week or so…

Jan 12, 1960

By Roland Blanchard

ABSTRACT RECENT discovery at Mount Isa of copper mineralization in commercial amount at a depth of 1000 ft., coinciding with downward termination of ore at about the same depth within the larger silver-lead-zinc lenses that have been the standby of Mount Isa's production to date, has been cited as an example in support of mineral zoning. A previous paper by the author and Graham Hall1 furnished a detailed description of the geology of the ore at Mount Isa as exposed up to that time, but necessarily dealt mainly with the silver-lead-zinc mineralization. Most of the geologic facts that constitute the first half of the present paper were set forth in the previous one in much greater detail, with full supporting evidence for the facts cited. The large amount of underground development (approximately 20 miles) and the extensive exploration carried out by diamond drilling (100,000 ft.) at Mount Isa, added to extensive microscope work conducted over a period of years, both by the company's staff and by others, had made possible the calculation within fairly close limits of mineralogical composition of the principal mineralized block of ground down to 1000-ft. depth, and had established closely the mineral succession, with reasons for deposition of the various minerals in the patterns now occupied by them. The geologic facts as outlined in the previous paper remain as stated; but because substantial development within the new copper ore body and further exploratory diamond drilling within the new silver-lead-zinc area (Race-course) have taken place since that paper was written, statements and figures relating to those two areas in the present paper supersede those furnished in the previous one. The recent work likewise has established more clearly the paragenetic relationship between the chalcopyrite and galena. Evidence confirming the relationship is furnished in the present paper. The facts of ore occurrence at Mount Isa show [ACCEPTED ZONAL SUCCESSION Silver sulphantimonides Galena Sphalerite Tetrahedrite Arsenical sulphides Chalcopyrite Pyrrhotite MOUNT ISA SUCCESSION Chalcopyrite In the main but Silver sulphantimonides wholly Tetrahedriteably not Galenacontemporaneous Pyrrhotite Sphalerite Arsenical sulphides They show further: (I) that instead of the silver-lead minerals yielding to increased zinc in depth, the zinc yields to increased silverlead; (2) no dovetailing of the silver-lead-zinc sulphides into chalcopyrite takes place; (3) despite the large amount of pyrrhotite deposited in the district (estimated at upward of 100,000,000 tons), its deposition took place under moderately low temperature conditions; (4) no evidence has been found for increase in temperature of deposition, with depth, to deepest exploration in ore (1495 ft.). The anomalous condition at Mount Isa, both as to the unorthodox mineral succession and the largely unorthodox pattern of mineral distribution, is explained in the present paper,

Jan 1, 1943

By Herbert Clark Hoover, Lou Henry Hoover

GEORGIUS AGRICOLA was not only the author of works on Mining and allied subjects, usually asso ciated with his name, but he also interested himself to some extent in political and religious subjects. For convenience in discussion we may, therefore, divide his writings on the broad lines of (1) works on mining, geology, mineralogy, and allied subjects; (2) works on other subjects, medical, religious, critical, political, and historical. In respect especially to the first division, and partially with regard to the others, we find three principal cases : (a) Works which can be authenticated in European libraries today ; (b) references to editions of these in bibliographies, catalogues, etc., which we have been unable to authenticate ; and (c) references to works either unpublished or lost. The following are the short titles of all of the published works which we have been able to find on the subjects allied to mining, arranged according to their present importance :-De Re Metallica, first edition, 1556; De Natura Fossilium, first edition, 15,46 ; De Ortu et Causis Subterraneorum, first edition, 1546; Bermannus, first edition, 1530 ; Rerum Metallicarum Interpretatio, first edition, 1546; De Mensuris et Ponderibus, first edition, 1533; De Precio Metallorum et Monetis, first edition, 1550 ; De Veteribus et Novis Metallis, first edition, 1546; De Natura eorum quae Effluunt ex Terra, first edition, 1546 ; De Animantibus Subterraneis, first edition, 1549. Of the " lost " or unpublished works, on which there is some evidence, the following are the most important:-De Metallicis et Machinis, De Ortu Metallorum Defensio ad Jacobum Scheckium, De Jure et Legibus Metallicis, De Varia Temperie sive Constitutione Aeris, De Terrae Motu, and Commentariorum, Libri VI. The known published works upon other subjects are as follows:-Latin Grammar, first edition, 1520; Two Religious Tracts, first edition, 1522; Galen (Joint Revision of Greek Text), first edition, 1525 ; De Bello adversus Turcam, first edition, 1528 ; De Peste, first edition, 1554. The lost or partially completed works on subjects unrelated to mining, of which some trace has been found, are:-De Medicatis Fontibus, De Putre¬dine solidas Partes, etc., Castigationes in Hippocratem, Typographia Mysnae et Toringiae, De Traditionibus Apostolicis, Oratio de rebus gestis Ernesti et Alberti, Ducum Saxoniae.

Jan 1, 1950

Crushed limestone is now being "de-dusted" at the Warner Co. plant in Bellefonte, Pa., by a new high-efficiency classifier utilizing aerodynamic principles not previously employed in classifiers. Crushed limestone for certain glass industry requirements must not have more than 10 pct fines in the overall aggregate, and it is the function of the new-type classifier to separate these fines from the coarse material. During the development of this classifier by the Buell Engineering Co. of New York, it was found to have possible applications for separating pulverized coal, sintered metals, ores, mineral flours, and fillers, among other items. Limestone from Warner's deep mine is initially crushed and particles larger than 3/8-in. mesh are burned in kilns to provide calcium oxide for the chemical industry. The 3/8-in. screenings are dried and crushed to -16 mesh for use by the glass industry. For those applications requiring a minimum of fines, no more than 10 pct -100 mesh material is allowable in the end product. Hence the need for high-efficiency separation.

Jan 11, 1960

The Office of Price Stabilization broke the copper price loggerhead between the U. S. and Chile when it permitted copper wire and brass mills to add to their ceiling prices 80 pct of the increase in cost of foreign copper above the 27 1/2 cents per pound specified in the agreement with Chile. Another step forward in the processing of taconite seems to have been made with the patenting of a process for the strengthening of taconite pellets. The patent was issued to Fred D. De Vaney and assigne to the Erie Mining Co., of Hibbing, Minn. Strength of the pellets is improved by adding from one to five pounds of starch or sodium silicate. A new iron ore deposit discovered on Vancouver Island will start producing soon, and is expected to yield 2 million tons of magnetite over its span of operation. A new mill will be built by the Argonaut Construction Co., of San Francisco, at the deposits of the Utah Construction Co., its parent organization. The Organization for European Economic Cooperation banned the use of nickel and nickel alloy in the manufacture of about 500 products in an attempt to conserve nonferrous metals in short supply. Some 18 members of the organization have already volunteered to restrict nickel consumption.

Jan 1, 1952

By Donald Barton

THIS paper outlines a time-saving graphical method of calculation for application to the interpretation of observations with the Eötvös torsion balance. Preliminary to the treatment of this short cut method which has been found practicable, the principal formu-las by which the student of interpretation can calculate the gradient and differential curvature produced by different types of bodies in different types of situa-tions are presented and discussed. It is necessary to split most geologic bodies into a series of simpler ones for which not too complicated formulas are avail-able. The gradient and differential curvature effects are calculated for each of the simple bodies and then summed to the total effect for the whole body. The calculations are considerable in number and, though more tedious than difficult, should be' entrusted to an experienced calculator. Considerable facility in qualitative interpretation can be acquired by the geophysicist from experience and from a thorough study of the types of gradient and differential curvature anomalies produced by the dif-ferent types of possible structural situations. How-ever, semi-quantitative calculations' of the probable structure bring out many relations that are not evident in a simple inspection of torsion balance results ; it throws out as impossible or improbable certain of the alternative structural possibilities that may seem equally probable under simple inspection of the results; it will determine more accurately the position of the crest of the structure; and reduce considerably the un-certainty in the interpretation and it is necessary to intelligent interpretations. The calculation of such cross-sections consists of a trial-and-error calculation of a body that will give gradient and differential curvature effects as closely as possible the same as those observed. From his knowledge of the gradient and differential curvature produced by different types of bodies, the geophysicist sketches a tentative cross-section of the structure as indicated-to him-by the observed results of the torsion balance survey, and the calculator then splits the struc-ture into blocks, and calculates the gradient and differ-ential curvature block by block. If, as rather usual, the calculated .gradient and differential curvature pro-files diverge considerably from, the respective observed ones, it is necessary to add and subtract blocks from the cross-section until a close agreement is obtained .between the calculated and observed profiles. The com-plete calculations have to be gone through for each block that is added or subtracted.

Jan 9, 1928

By A. R. Jr. Amos

LOG washers have been used for many years in the washing of clay iron ores, phosphate rock and manganese ores, but not until the past 15 years have they been employed to any extent in the preparation of aggregate materials and fluxing stone. For a machine of such importance where tenacious clay or soft rock must be eliminated, there are few data generally available. The purpose of this paper is to set forth the results obtained from several operations, together with a few suggestions for planning a specific installation. Where the material to be washed out consists of loose surface soil, silt, or small amounts of quickly soluble clay, there is little competition with other forms of washers, because greater power and maintenance are required for the operation of log washers, but where the foreign matter is a stiff clay, such as occurs with high-calcium limestones and in marginal gravel deposits, the ability of other kinds of washers to eliminate com-pletely the hard clay balls is at least uncertain. Then the log washer comes into its own field, for with the breaking and churning action of the logs it will clean out the toughest clay. Even with material from the hydraulic dredge, if it contains tough clay, the log washer is desirable unless the gravel is subjected to a costly soaking and rehandling process. Recently there has been a considerable development in other types of machines to accomplish these results but it is not within the scope of this paper to make comparisons between competitive types, but to present the best obtainable data on log washers only. From the primitive design that gave it its name, a long log hewn from a tree, with paddles forged to shape from strap iron and attached by lag screws, the log washer has gradually been developed to the present all-steel type. As now manufactured, the log washer consists essentially of two built-up logs on which are mounted a series of paddles, carried by shafts fitted at the ends of the logs on bearings fastened outside the enclosing steel box, or trough, which is set at an angle of about 5° to 10° and into which the material is fed. Stuffing boxes at the places where the shafts pass through the box at the lower end are equipped with water-

Jan 1, 1936

By A. R. Jr. Amos

LOG washers have been used for many years in the washing of clay iron ores, phosphate rock and manganese ores, but not until the past 15 years have they been employed to any extent in the preparation of aggregate materials and fluxing stone. For a machine of such importance where tenacious clay or soft rock must be eliminated, there are few data generally available. The purpose of this paper is to set forth the results obtained from several operations, together with a few suggestions for planning a specific installation. Where the material to be washed out consists of loose surface soil, silt, or small amounts of quickly soluble clay, there is little competition with other forms of washers, because greater power and maintenance are required for the operation of log washers, but where the foreign matter is a stiff clay, such as occurs with high-calcium limestones and in marginal gravel deposits, the ability of other kinds of washers to eliminate com-pletely the hard clay balls is at least uncertain. Then the log washer comes into its own field, for with the breaking and churning action of the logs it will clean out the toughest clay. Even with material from the hydraulic dredge, if it contains tough clay, the log washer is desirable unless the gravel is subjected to a costly soaking and rehandling process. Recently there has been a considerable development in other types of machines to accomplish these results but it is not within the scope of this paper to make comparisons between competitive types, but to present the best obtainable data on log washers only. From the primitive design that gave it its name, a long log hewn from a tree, with paddles forged to shape from strap iron and attached by lag screws, the log washer has gradually been developed to the present all-steel type. As now manufactured, the log washer consists essentially of two built-up logs on which are mounted a series of paddles, carried by shafts fitted at the ends of the logs on bearings fastened outside the enclosing steel box, or trough, which is set at an angle of about 5° to 10° and into which the material is fed. Stuffing boxes at the places where the shafts pass through the box at the lower end are equipped with water-

Jan 1, 1936

By Thos Gibson

THE object of taxation is the raising of a revenue. Unless a tax accomplishes this, it is a failure. The right to take for public purposes a part of the moneys obtained from the carrying on of private enterprises is an attribute possessed only by a lawful government, and may indeed he called the supreme attribute of government. In free, democratic communities this power must of necessity rest upon the consent of the governed. Power implies obligation, hence it is obviously the duty of a government, in framing a system of taxation, to provide one which, while effective in producing a revenue, is also just and impartial. It will be conceded that mines and mining property ought to bear a fair share of the public expenditure. The question is, upon what basis taxation should proceed. Two separate taxing principles are usually contended for: Taxation should be proportionate to the benefits received by the person or property taxed; taxation should be based on ability to pay. A third is sometimes added, taxation should have reference to the extent and value of the natural resources enjoyed. As applied to mining taxation, it is pointed out by those who support the first mentioned basis that, mines being usually situated in rocky and hence sparsely peopled regions, mining companies are frequently obliged to construct roads, railways, telegraph and telephone lines, schools, water and sewerage systems, and many other amenities and conveniences of civilization, the cost of which in regions better suited for agriculture and consequently more thickly populated, has either been defrayed locally, or can be spread over a sufficiently large taxable group of people to materially lighten the financial burden on the mine. The mining com¬pany, it is argued, having made these outlays, should receive credit for, them and be relieved of taxation to a corresponding extent. There may be some force in this contention, but the situation is capable of relief without attempting to place taxation upon so unworkable a basis as the value of benefits received. Who is to be the judge of these benefits, and how are they to be valued? The very existence of a mining company and its ability to carry on business in peace and security, depend on the prevalence of law and order, which is a result of good government. The state provides protection against violence, and courts of law for

Jan 4, 1919

By Hugh Marriott

MANGANESE and its ores have been recently dealt with in comprehensive papers to the Iron and Steel Institute by Sir Robert Hadfield, and in a series of papers read before the A. I. M. E. at the Cleveland meeting. I have taken the opportunity of adding this mineral, to my records of the "World's Mineral Production and Consumption," as recently pub-lished in the Economist ?. The tables bring out the following significant facts: The world's production has increased by 10 per cent since 1913. India's production has increased by 3 per cent since 1.913, the supply from this source now being 31.1 per cent of the world's output. Russia is now producing at about half its pre-war rate and yields 19 per cent of the world's production. West Africa supplies 12.5 per cent of the world's total output. Brazil's present output is 2.5 times that of the pre-war period, being 11.3 per cent of the world's output.

Jan 9, 1927

By Alden Greninger

THAT metallographic structures analogous to the martensite of steel may be found in certain copper-aluminum and copper-tin alloys has been known for many years; similar structures recently were found in certain copper-zinc alloys.1 In all three of these alloy systems the martensite structures result from transformation of the metastable ß phase when the speed of cooling from the ß range is sufficiently high to suppress decomposition into equilibrium phases. ? In the normal decomposition of solid solutions into equilibrium phases, diffusion is needed to bring about the necessary changes in concentration, and the rate of reaction falls almost to zero at temperatures slightly above room temperature. The rates of reaction for martensite processes, however, are not dependent upon temperature; the transformation does not require readjustments of concentration. For example, the marten-site transformation in 60:40 (ß) copper-zinc does not begin until the temperature has dropped to about minus 30° C., and then continues down to minus 130° C. and probably even at lower temperatures.1 Further-more, martensite processes apparently proceed only while the tempera-ture is falling, within the proper range, and cease completely while the temperature is held constant; ? and they cannot be suppressed by extremely rapid cooling although the rate of cooling for some alloys may be increased to over 10,000 times the critical cooling velocity. Isaitschew, Kaminsky and Kurdjumow2 account for these observed behaviors of martensite processes by postulating that the mechanism " . . . consists in a regular rearrangement of the lattice in such a way

Jan 1, 1939

By T. K. Perkins, O. C. Johnston

Because of the influence of dispersion on miscible-displacement processes, diffusion and dispersion phenomena in parous rocks are of current interest in the oil industry. This paper reviews and summarizes a great deal of pertinent information from the literature. Porous media (both unconsolidated packs and consolidated rocks) can be visualized as a network of flow chambers, having random size and flow conductivity, connected together by openings of smaller size. In such a porous medium, the apparent diffusion coefficient D is less than the molecular diffusion coefficient Do, as measured in the absence of a porous medium. For packs of unconsolidated granular material the ratio D/D, is about 0.6 to 0.7. For all porous rocks, both cemented and unconsolidated, the ratio of diffusion coefficients can also be represented as D/Do = 1/FF where F is the for- mation electrical resistivity' factor and 4 is the porosity. If fluids are flowing through the porous medium, dispersion may be greater than that due to diffusion alone. At moderate flow rates the porous medium will create a slightly asymmetrical mix zone (trailing edge stretched out), with the longitudinal dispersion coefficient approximately proportional to the first power of average fluid velocity (if composition is nearly equalized in pore spaces by diffusion). If the velocity in interstices is large enough, there will be insufficient time for diffusion to equalize concentration within pore spaces. In this region, longitudinal dispersion increases more rapidly than fluid velocity. At low velocities in interstices, transverse dispersion is characterized by a region in which transverse diffusion dominates. If the fluid velocity gets high enough, there will be a transition into a region where there is stream splitting with mass transfer but with insufficient residence time to completely damp-out concentration variations within pore spaces. There are several variables that must be con- trolled to get consistent longitudinal and transverse dispersion results, viz., (1) edge effect in packed tubes, (2) particle size distribution, (3) particle shape, (4) packing or permeability heterogeneities, (5) viscosity ratios, (6) gravity forces, (7) amount of turbulence, and (8) effect of an immobile phase. INTRODUCTION Diffusion and dispersion in porous rocks are of current interest to the oil industry. This interest arises because of the influence of dispersion on miscible-displacement processes. In a recovery process utilizing a zone of miscible fluid, there is the possibility of losing miscibility by dissipating the miscible fluid or by channeling or "fingering" through the miscible zone. Diffusion and dispersion are two of the mechanisms that may lead to mixing and dissipation of the slug. On the other hand, dispersion may tend to damp-out viscous fingers which may be channeling through the miscible slug. 58 Hence, dispersion may be detrimental or beneficial (if it prevents fingering through the miscible zone). Therefore, it is doubly important that we understand these processes. In this paper we review, summarize and interpret a great deal of information from the literature. In particular, we will briefly discuss molecular diffusion in miscible fluids. Then we will discuss what differences to expect for diffusion in a porous rock. If there is movement of the fluid through the rock, then there may be an additional mixing or "dispersion". Furthermore, the dispersion longitudinally (in the direction of gross fluid movement) and transverse to the direction of fluid movement will not be equal. We will discuss both types of dispersion as well as several variables which can affect dispersion (viscosity differences, density differences, turbulence, heterogeneity of media, etc.). This group of variables has sometimes led to difficulty when comparing literature data. DIFFUSION OF MISCIBLE FLUIDS If two miscible fluids are in contact, with an initially sharp interface, they will slowly diffuse into one another. As time passes, the sharp interface between the two fluids will become a diffuse

By Robert Glass Cleland

THE OUTBREAK of World War II found Phelps Dodge, thanks to both foresight and good fortune, in a position to increase production of its mines and factories to meet the insatiable military and domestic needs of the times, far beyond all previous records. With the timely completion of the expansion program at Morenci, the company's copper output rose to approximately 447 million pounds in 1942 and to over 478 mil- lion pounds the next year, compared to some 300 million pounds in 1939. To meet the civil and military needs for fabricated cop- per products, the Phelps Dodge Copper Products Corporation carried out an expansion program comparable in size to that of the Phelps Dodge mining operations. It built new plants, enlarged and reorganized those already in operation, multiplied the number of technical experts on its staff, adopted new methods and new machines for the new prod-

Jan 1, 1952

By Kenneth P. Katen

INTRODUCTION Though the use of continuous mining machines consolidated the operations of cutting, drilling, blasting, and loading in one machine that would theoretically provide uninterrupted production, it was soon realized that the face haulage and roof support operations remained as major impediments to continuous production. The ability to provide not only continuous cutting and loading, but also continuous haulage and roof support (see Fig. I), was the basis for the introduction of mechanized longwall systems in this country from Europe in 1951. The early systems employed friction props for roof support, but were to become obsolete shortly after introduction of the first hydraulically powered, self-advancing supports in 1960. Since then, use of the longwall technique has grown to the point where it is currently providing more than 5% of the annual output of underground coal mines in the United States. The shortwall system had its origin in Australia, but was first introduced into this country in 1962 following the development of powered roof supports. It, too, provides for continuous cutting, loading, and roof support (see Fig. 2), but has not experienced the widespread popularity of longwall due to its inherent inability to easily provide for continuous haulage. While there are in the neighborhood of 100 longwall systems currently in operation in this country, there are only a handful of short- wall operations providing production of slightly more than 907 184.7 t/a (1,000,000 stpy) Both of these systems provide uninterrupted roof support for face operations by means of hydraulically powered steel roof supports. In each case, the coal removal consists of open-end cuts made from the narrow end of a large rectangular pillar (panel) which has been blocked out by continuous miners developing entries around its perimeter. However, this is the extent of the similarities between the two systems. It is hoped

Jan 1, 1981

THE following employment items ore made available to AIME members on a nonprofit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of the Personnel Service ore at 8 W. 40th St., New York 18; 100 Farnsworth Ave., Detroit; 57 Post St., Son Francisco; 84 E. Randolph St., Chicago 1. Applicants should address all mail to the proper key numbers in care of the New York office and include 6c in stamps for forwarding and returning application. The applicant agrees, if. placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of positions available for $3.50 a quarter, $12 a year. MEN AVAILABLE Graduate Mining Engineer, 31, married. Six years' engineering experience, mining and construction, U. S. A. and Alaska. Underground metal mining, production, development, geology, mine engineering. Engineering on airfield construction, earthwork, location work, mapping, topography, road location; office work. Commercial pilot license. Desires position mining or construction. Available 45 days. Prefer Latin America. M-676-477-E-8-San Francisco. Mining Engineer, 42, married, one child. Fourteen years' mining with much supervisory experience in developing and operating metal mines; also mine safety engineering. Familiar with many large and small mines in the western U. S. and Mexico. Excellent references. M-677.345-E-1¬San Francisco.

Jan 1, 1952

By ALFRED D. FLIWN

ENGINEERING COUNCIL is not "about to die," as some persons are saying. Through a natural and foreseen reorganization, Council is entering a new stage of existence with enlarged power for usefulness. Its early constituents have made it possible for many more of their fellow engineers and men of other technical vocations -to take a- share in its activities, responsibilities and support. A new organization is being set up, but it is really a new embodiment of the same spirit of service. Another step is being taken toward the full acceptance by the technical professions of their obligation to the public and to one another for those services which can -be rendered only through effective organization. A brief retrospect is timely. Engineering Council was established in the spring of 1917, as a department of United Engineering Society in response to requests of its Founder Societies. .It followed various attempts of these societies to deal through joint committees with public questions affect¬ing engineers -and with inter-society affairs. These attempts had very limited results. In the new by-laws adopted by United Engineering Society, the purposes and-powers d-powers of Engineering Council were thus defined: "To provide for convenient cooperation between the four Founder Societies, for the proper consideration of questions- of general interest to engineers and to the public, and to provide the means for united , action upon questions of common-concern to engineers.

Jan 1, 1920

By E. M. Furness, A. S. Henderson

ORIGINALLY the Babbitt experimental plant grinding circuit consisted of one rod mill 10 ½ ft diam by 12 ft long in open circuit followed by two ball mills 10 ½ ft diam* 12 ft long in parallel circuit. Shortly after operations commenced it was apparent that the rod mill could not function satisfactorily at the required 125 gross tons of ore per hr. Attempts to operate at this rate produced: 1) excessive tramp material over rod mill trommel screen which could not be handled in this open circuit and 2) excess build-up of coarse ore in the ball mill circuits because of inadequate rod mill grinding. Since Reserve Mining Co. ore must be ground to 85 pct -325 mesh to produce a satisfactory iron concentrate, an efficient and controlled grinding circuit is highly important. The first step in trying to resolve this grinding problem was to determine which unit of the circuit was actually in trouble and to what extent. A series of tests conducted at a lower tonnage rate of rod mill feed indicated that one ball mill could grind satisfactorily at rates up to 70 gross tons of rod mill feed per hr.

Jan 12, 1957