Search Documents

By R. H. Jacoby, V. J. Berry

Future depletion performance and ultimate oil recovery from reservoirs producing under volumetric control are often predicted with the aid of a material balance equation. When the reservoir fluid is very volatile, however, certain assumptions implicit in the use of the conventional methods are no longer valid. This is became laboratory differential vaporization test procedures do not adequately represent the reservoir depletion process and the performance of surface separation facilities. In such cases recovery of stock tank oil per unit of pressure decline can be predicted only from a detailed knowledge of the separator conditions and the over-all composition of the fluid entering the wellbore at each stage of depletion. Surface recovery is not simply related to the total quantity of liquid flowing into the well under reservoir conditions. In order to improve predictions for reservoirs which produce volatile oils, a step wise method of calculation has been developed. This method uses relative permeability data and multicomponent flash calculations to predict oil and gas production as a function of reservoir pressure. Calculations are presented for a reservoir containing a volatile crude oil, and predicted tank oil recovery by primary depletion is more than twice that predicted by conventional methods which are known to be adequate for ordinary black crude oils. Calculated maximum produced gas-oil ratio is less than one-fourth of the conventional prediction. Wellstream compositions have also been used to determine variation in stock tank oil composition and liquid content of the separator gas. This information is of particular importance for crude stabilization calculations and for design of gasoline plant facilities to recover LPG and natural gasoline. INTRODUCTION The estimation of oil reserves and the prediction of future recovery performance of petroleum reservoirs is a frequent task of the petroleum engineer. If the reservoir produces under volumetric control, performance calculations for primary depletion are made by combining oil and gas material balances with the gas-oil flow characteristics of the reservoir rock. For black oil reservoirs, the Schilthuis1 type material balance is commonly employed. For gas or gas-condensate reservoirs, where only one phase is flowing under bottom-hole conditions, a more simplified material balance is used. In the period in which these material balance methods were conceived and put into practice, it was common to classify reservoirs according to the type of fluid produced as (1) black oil reservoirs, or (2) gas or gas-condensate reservoirs. Recently, however, deeper drilling and more extensive studies of reservoir fluid properties have led to the recognition of reservoir fluids with phase characteristics between those of ordinary black oils, and gases or gas-condensate fluids. These intermediate fluids contain relatively large amounts of the hydrocarbons ethane through decane and are found in deep, high temperature (250°F) reservoirs. Such fluids are often referred to as high shrinkage crudes or "volatile oils." They are usually characterized by tank oil gravities above 45° API. high solution gas/oil ratios,

Jan 1, 1958

By C. E. Berry

Natural stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may be lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a a ance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. Materials Tested 1. Belgian Si1ex.—Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.—Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.—Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.—Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1948

By C. E. Berry

Natural stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may be lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a a ance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. Materials Tested 1. Belgian Si1ex.—Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.—Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.—Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.—Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1948

By Eleanor Haslem, Carl A. Zapffe

THE present investigation has three principal purposes: I. To develop a method for measuring hydrogen embrittlement that avoids certain errors complicating previously used methods. 2. To explore in a preliminary way some of the fundamental factors controlling embrittlement. 3. To apply the measurements specifically to stainless grades of steel, whose sensitivity or insensitivity to hydrogen embrittlement has never been clearly defined. SELECTING A TEST METHOD Hydrogen embrittlement is a condition of low ductility resulting from excessive absorption of hydrogen by the steel at some period in its history, and may be revealed by almost any test involving cold deformation. Tensile tests, impact tests, and bend tests are commonly used for detecting hydrogen embrittlement; although numerous other tests, such as cold-upsetting or extrusion, could be used. The simplicity of using a wire specimen for cathodic and acid pickling tests, and the especial adaptability of the bend test to wire specimens, led to selection of the bend test for the present research. Bend tests usually have been of three general types: (I) fatigue, (2) reversed bend, and (3) single bend. The first two types, though widely used, are inaccurate because their measurements are counteracted by an aging effect; and the third type has not been developed to its fullest utility. The effect of cold-working in removing hydrogen is well known. During a bend test hydrogen can be observed escaping from the convex side simply by coating the specimen with oil; and any technique employing flexing or reverse bending may therefore have its measurements masked because the mechanical action reduces the embrittlement during the test. This factor is so important that even elastic flexing of a hydrogen-charged wire specimen should be avoided before testing if accurate measurements are desired. DEVELOPING A MACHINE FOR MEASURING HYDROGEN EMBRITTLEMENT As for the single-bend test, its theory is good, and recovery caused by mechanical work is kept to a minimum. With a given degree of hydrogen embrittlement, a specimen will break at a given angle if the bending is applied unidirectionally and uniformly. The radius of the bend must be kept constant; and the rate of bending should be a constant, slow enough to allow reading of the breaking angle, and yet rapid enough to prevent significant recovery from the escape of hydrogen during bending. A simple apparatus (Fig. I) was constructed using a type H Foxboro drive unit A, which is a synchronous motor with a gear-reduction ratio of 600 to I. A cord, fixed at one end to a wooden pulley B on the drive shaft of the motor, follows the pe-

Jan 1, 1946

By W. R. Seyfried

THE problem of extracting alumina from clay and low-grade bauxites has been the subject of considerable interest for some time. The basic reason, of course, lies in the fact that known reserves of high-grade bauxite are not inexhaustible and that the present commercial process cannot successfully cope with low-grade bauxites or clay. Ultimately it may be necessary to use these poorer raw materials for all commercial operations. An unprecedented demand for aluminum during the war emergency and the constantly threatened shortage of imported bauxite caused the United States Government to take an active role in this problem. Through the National Academy of Sciences, the War Production Board and the Defense Plant Corporation, it investigated processes and finally selected four to be used in the construction and operation of four experimental plants. Each plant was to be designed in such a way as to facilitate its incorporation into a larger commercial plant should the need arise. The Chemical Construction Corporation process, or "Chemico" ammonium sulphate process as it is better known, was one of the four selected. The extensive literature and patents on record before the war generally follow one of two process-types depending upon the extracting reagent used. One group uses an acid reagent, the other an alkali. The Chemico process uses an acid reagent. For those interested in other processes described in literature, there is a short bibliography at the end of this paper. The basic steps of all acid extraction processes are: (I) to make the aluminum silicates acid soluble, (2) to separate the released alumina from impurities and insoluble gangue, and (3) to recover the reagent for re-use. THE PROCESS AS PLANNED In April 1941, a group of chemists and engineers of the Chemical Construction Corp. became interested in the problem of extracting alumina from clays and low-grade bauxites and, under the leadership of Mr. Blakeslee Barnes, Vice President and General Manager of the Company, first drafted a process in July of that year-five months prior to Pearl Harbor. The work continued in our research laboratories and with a small pilot plant. By June 1943, the work had progressed to a point where it was possible to apply for a patent on the process which was U.S. patent 2,405,426, granted August 6, 1946. Immediately prior to the development of the Salem plant, the process was envisaged to be as follows: I. The first step was to make the aluminum silicates acid soluble. It was planned: (a) Clay or low-grade bauxite would be roasted at 700 to 800°C (1292° to 1472°F), (b) The roasted ore would then be leached with hot aqueous ammonium bisulphate to form a slurry. In this way the

Jan 1, 1947

By E. C. van Reuth

FIFTY-three alloys have been examined in the Fe-W and Co-W alloy systems in an attempt to verify the finding of o phases in these systems as reported by Goldschmidt.' The alloys were examined metallographically and by X-ray diffraction. The 10-g specimens were made by powder metallurgy techniques. Very fine, high-purity powders were compressed in a double-acting die at 120,000 psi after hydrogen reduction. All compacts were then sintered for 200 hr at 950°C in a helium atmosphere. Metallographic investigation and X-ray diffraction proved this time to be sufficient to allow complete homogenization before the subsequent high-temperature anneal. Each specimen was then sealed into an evacuated silica capsule and annealed at 1400"or 1500 C (except two) for 25 hr. (The 60 pct Fe and 55 pct Co alloys taken to 1610"and 1680°C respectively were held at these temperatures for 1hr. However, since these structures were at equilibrium before the anneal, and in view of their resultant structures, it is assumed that they reached equilib-

Jan 1, 1960

By Edward Keller

In order to conduct intelligently the sampling of copper of various forms and grades, solid or in molten furnace-charges, a knowledge of this subject is essential. Yet figures and tests have been persistently withheld from publication, and the books at our command give us little or no information in this regard. This gap in our copper-literature has led to a series of experiments, the results of which are given below. Nearly all gold- and silver-bearing copper, destined for shipment, is cast into the form of bars or pigs. For the sampler, the question arises, Does copper, so cast, remain homogeneous ? If it does, sampling should present no difficulties; but, from experience, we know that this is not the case, and we are thus led to study the behavior of the precious metals arid impurities in copper when the latter changes from the molten to the solid state. For the purpose of the experiments here described, all available grades of copper were selected, and all of them mere subjected to the same conditions, an important requisite for proper comparison. The molten copper obtained directly from reverberatory- and blast-furnaces was cast in a cast-iron mould, the sides and bottom of which were 1 inch thick, and would, therefore, give the copper a fair length of time to chill. The inside dimensions of the mould, and, consequently, of the block of copper obtained, were: length, 10 inches; width, 9 inches; and depth, 5 inches. Fig. 1 illustrates the method employed to obtain samples from these blocks. A was cut away, and the face so produced BALTIMORE COPPER WORKS,

Jan 1, 1898

By O. A. Cheadle, F. E. Lane

ThE computer program for arbitrary crystal systems reported by Camp and Clum' has been modified to make it more convenient for hexagonal crystals. The program' uses the Miller indexes (hkl) which can be confusing for hexagonal crystals while the modified program uses the Miller-Bravais indexes with four axes; e.g., the angles between the (110) planes, Fig. 1, are 0 and 90 deg but in the (hkil) system the angles between the (1150) planes are 0 and 60 deg. If a Laue photograph is taken of a crystal oriented with the prismatic planes nearly parallel to the film then the spots on the stereo graphic projection will be from high-index planes. The probable positions of the low-index planes, e.g., (0001) plane, can only be obtained from the intersection of zones and this is not accurate to 1 or 2 deg. The number of planes considered by the program (card 1)' has to be limited to the ones of low index or the program time is excessive but a solution will not be obtained if one of the spots has an index that is not being considered. To overcome this problem the program1 was modified so that if no fit was obtained at *1 deg (card 3) of the tabulated angles then ±2 or ±3 deg was tried. If still no solution was obtained either due to one of the angles not being measured correctly to ±3 deg or because one of the spots was from a high-index plane, then the last spot was discounted and a fit tried for the remaining spots at i1 deg, and so forth. The minimum number of spots that the program will try to fit is five. If the limit on any individual index is 4 (card 1) and (h + k + l + 1) is six then twenty-three planes are considered and there are over 1000 interplanar angles. Many pairs of planes have very similar interplanar angles and with the errors previously mentioned the program will often produce several alternative solutions to a group of spots particularly at ±2 or ±3 deg. However without the program the alternative solutions would probably not have been found. If a large number of spots are used the number of possible fits is reduced. In the example shown in Fig. 2, if only spots which are on the film are used (case 1) the program gives six possible solutions, Table I. However if points 7 and 8 are also used (case 2) the program gives only one fit which also agrees with a standard projection of the crystal. In addition to time-saving the program ensures that a correct solution is obtained since it is unlikely that all the alternatives would have been gound manually; the first would probably be assumed to be the correct solution. The program has been used for zirconium crystals but is equally suitable for other hexagonal materials.

Jan 1, 1969

By Walter S. Lutz, J. T. Griffith

The rainfall during the last six months of 1942 in Scranton and vicinity was 24.06 in.—only 4.35 in more than the average for this district in any equivalent period—yet that rain forced The Hudson Coal Co. to handle 38.8 tons of water for every ton of coal mined. It filled to overflowing, or to a higher level, 14 flooded mine areas holding, in total volume, 8.3 billion gallons of water in storage; brought about a pumpage of 11.4 billion gallons in the months of December 1942 and January, February and March 1943 Half of the total energy generated or purchased (44,322,980 kw-hr.) was required to keep the mines sufficiently free of water to permit the mining of coal during a period of much needed output. Fig. I shows the extent to which this flooding of exhausted and idle properties has proceeded, and is known to be proceeding further, at the upper end of the Northern field. This rainfall (24.06 in.) means 80,559,444 tons of water on approximately 46.2 sq. miles of area tributary to the pumping plants. During the high rainfall period, 72,687,661 tons went underground, being pumped at the stations in this territory. This means an inflow of 88per cent, a runoff of 12 per cent compared with 64 per cent during normal conditions in a normal region. During this period no floods, either surface or underground, had to be dealt with, although the streams and rivers were high on several occasions. In general, the rainfall for the first three months of 1943 can be described as heavy but not abnormal.9 These figures not only indicate the large volumes of water to be handled but, by their very size, they also emphasize that the mine-water problem is not to be conquered, at least from an economical standpoint, by merely buying and installing more and more pumps. Into the solving of this water problem must go much planning, adhering to the principle of keeping the highest percentage of water at the highest possible level for the longest period of time; the storage of huge volumes in sumps capable of being reduced after the flood inflow and at rates less than the inflow; plans for prevention of surface inflow; provision of the minimum of pumping capacity arranged to as nearly 100 per cent pumping load factor as is possible; intercompany joint pumping plants; the conducting of water from one plant to another and from one property to another over distances measured in miles; priorities in power to the threatening situations; and. balance of the necessities and dangers existent in one colliery over another, day by day, when quantities of water are running high. Despite these astronomical figures of water volumes, their disposal to the surface is accomplished reasonably cheaply because, although the annual cost of $575,020 is a large sum, the cost per ton is about 0.1168 cents. Credit for this goes

Jan 1, 1947

By J. T. Griffith, Walter S. Lutz

The rainfall during the last six months of 1942 in Scranton and vicinity was 24.06 in.—only 4.35 in more than the average for this district in any equivalent period—yet that rain forced The Hudson Coal Co. to handle 38.8 tons of water for every ton of coal mined. It filled to overflowing, or to a higher level, 14 flooded mine areas holding, in total volume, 8.3 billion gallons of water in storage; brought about a pumpage of 11.4 billion gallons in the months of December 1942 and January, February and March 1943 Half of the total energy generated or purchased (44,322,980 kw-hr.) was required to keep the mines sufficiently free of water to permit the mining of coal during a period of much needed output. Fig. I shows the extent to which this flooding of exhausted and idle properties has proceeded, and is known to be proceeding further, at the upper end of the Northern field. This rainfall (24.06 in.) means 80,559,444 tons of water on approximately 46.2 sq. miles of area tributary to the pumping plants. During the high rainfall period, 72,687,661 tons went underground, being pumped at the stations in this territory. This means an inflow of 88per cent, a runoff of 12 per cent compared with 64 per cent during normal conditions in a normal region. During this period no floods, either surface or underground, had to be dealt with, although the streams and rivers were high on several occasions. In general, the rainfall for the first three months of 1943 can be described as heavy but not abnormal.9 These figures not only indicate the large volumes of water to be handled but, by their very size, they also emphasize that the mine-water problem is not to be conquered, at least from an economical standpoint, by merely buying and installing more and more pumps. Into the solving of this water problem must go much planning, adhering to the principle of keeping the highest percentage of water at the highest possible level for the longest period of time; the storage of huge volumes in sumps capable of being reduced after the flood inflow and at rates less than the inflow; plans for prevention of surface inflow; provision of the minimum of pumping capacity arranged to as nearly 100 per cent pumping load factor as is possible; intercompany joint pumping plants; the conducting of water from one plant to another and from one property to another over distances measured in miles; priorities in power to the threatening situations; and. balance of the necessities and dangers existent in one colliery over another, day by day, when quantities of water are running high. Despite these astronomical figures of water volumes, their disposal to the surface is accomplished reasonably cheaply because, although the annual cost of $575,020 is a large sum, the cost per ton is about 0.1168 cents. Credit for this goes

Jan 1, 1947

By H. T. Clark, S. Feigenbaum

The importance of measuring the temperature of molten steel in the open-hearth furnace has been recognized for many years. Poor temperature control may be costly to steelmaking operations and lead to a lowered quality of the steel. Low or excessive temperatures may shorten the life of the furnace, ladles and molds. Rates of reactions in the furnace and efficiencies of deoxidizers are known to change materially with a change in the temperature of the metal and slag. Ladle skulls and mold and stool stickers cause steel to be scrapped instead of being converted into useful products. Finally, the structure, segregation and surface condition of ingots are affected by the teeming temperature. Mill investigations of the effect of bath temperature upon steelmaking operations have been largely qualitative in character, based upon observations by practical melting men. The physical chemist has used the empirical information available and has reached reasonable and useful conclusions with respect to the various melting processes. The introduction of a reliable direct-reading pyrometer will permit accurate quantitative evaluation of the effects of temperature and should furnish a more rational basis for study of the thermochemistry of steelmaking. The problem is not merely one of making a small numbcr of temperature measurements in the open-hearth furnace. This has been done by several methods to a * Assistant Manager, Research and Development, Jones and Laughlin Steel Corporation, Pittsburgh, Pennsylvania. Issued as T.P. 2031 in MEtals Technology, June 1946; also in Open Hearth Proc., 1946. † Open-hearth Metallurgist, Jones and 1aughlin Steel Corporation, Aliquippa. Pennsylvania. degree of precision that was apparently satisfactory. Considerable effort by a number of investigators has been directed rather to the development of an open-hearth bath pyrometer that would be both accurate and practical for routine measurements. To be practical, the pyrometer should be inexpensive to operate; that is, the installation, operating and maintenance costs should be exceeded by the tangible benefits to the open-hearth operator. Temperatures from 2800' to 3100°F. are. encountered in the open-hearth furnace. The surface of the molten metal is covered by several inches of slag, which prevents direct observation of the metal surface for optical or radiation measurements. Both slag and metal are highly reactive at these temperatures and will attack to a greater or lesser extent any material immersed in them. Adequate protectioil of thermocouples, which of necessity must be brought to the temperature of the bath, has generally resulted in a large, heavy assembly made up of brittle materials, unsuited for handling on the open-hearth floor. The life of the equipment was short and maintenance was an important consideration. Earlier Work Any of a number of Physical Properties of liquid steel could conceivably be used a a basis for temperature measurement. Efforts to the present time, however, have been confined largely to measuring either the thermal electromotive force generated between two dissimilar materials immersed in the steel or the intensity of radiation from the surface of the steel. These

Jan 1, 1947

By H. T. Clark, S. Feigenbaum

The importance of measuring the temperature of molten steel in the open-hearth furnace has been recognized for many years. Poor temperature control may be costly to steelmaking operations and lead to a lowered quality of the steel. Low or excessive temperatures may shorten the life of the furnace, ladles and molds. Rates of reactions in the furnace and efficiencies of deoxidizers are known to change materially with a change in the temperature of the metal and slag. Ladle skulls and mold and stool stickers cause steel to be scrapped instead of being converted into useful products. Finally, the structure, segregation and surface condition of ingots are affected by the teeming temperature. Mill investigations of the effect of bath temperature upon steelmaking operations have been largely qualitative in character, based upon observations by practical melting men. The physical chemist has used the empirical information available and has reached reasonable and useful conclusions with respect to the various melting processes. The introduction of a reliable direct-reading pyrometer will permit accurate quantitative evaluation of the effects of temperature and should furnish a more rational basis for study of the thermochemistry of steelmaking. The problem is not merely one of making a small numbcr of temperature measurements in the open-hearth furnace. This has been done by several methods to a * Assistant Manager, Research and Development, Jones and Laughlin Steel Corporation, Pittsburgh, Pennsylvania. Issued as T.P. 2031 in MEtals Technology, June 1946; also in Open Hearth Proc., 1946. † Open-hearth Metallurgist, Jones and 1aughlin Steel Corporation, Aliquippa. Pennsylvania. degree of precision that was apparently satisfactory. Considerable effort by a number of investigators has been directed rather to the development of an open-hearth bath pyrometer that would be both accurate and practical for routine measurements. To be practical, the pyrometer should be inexpensive to operate; that is, the installation, operating and maintenance costs should be exceeded by the tangible benefits to the open-hearth operator. Temperatures from 2800' to 3100°F. are. encountered in the open-hearth furnace. The surface of the molten metal is covered by several inches of slag, which prevents direct observation of the metal surface for optical or radiation measurements. Both slag and metal are highly reactive at these temperatures and will attack to a greater or lesser extent any material immersed in them. Adequate protectioil of thermocouples, which of necessity must be brought to the temperature of the bath, has generally resulted in a large, heavy assembly made up of brittle materials, unsuited for handling on the open-hearth floor. The life of the equipment was short and maintenance was an important consideration. Earlier Work Any of a number of Physical Properties of liquid steel could conceivably be used a a basis for temperature measurement. Efforts to the present time, however, have been confined largely to measuring either the thermal electromotive force generated between two dissimilar materials immersed in the steel or the intensity of radiation from the surface of the steel. These

Jan 1, 1947

By F. L. Toy, C. E. Sims

I. A. Sirel—I would like to ask Mr. Sims what would the preferred hot metal analysis be as far as manganese and silicon are concerned if you used specially made iron for this process instead of basic iron. C. E. Sims (authors' reply)—A preferred composition would contain somewhat less silicon than the basic pig iron used in these experiments. High silicon requires a large lime addition. Lime must be added in sufficient quantity to neutralize the silica formed and to leave an excess for dephosphorization. Manganese presents almost no problem in operation. It is almost completely oxidized and, in burning, develops considerable heat. The evidence indicates, however, that, in continuous commercial operation, there will be an excess of heat produced, and the bath will need to be cooled in some manner as by the addition of scrap or by utilizing the energy for the direct reduction of ore. There do not seem to be any serious limitations on composition of pig iron. One heat was made with an iron containing 2.27 pct silicon and the phosphorus finished at 0.007 pct. In another, the iron contained 0.45 pct phosphorus which was lowered to 0.019 pct. This indicates considerable leeway in composition. D. R. Loughrey—We are all very much interested in the recent discovery of very large deposits of iron ore both in Labrador and in Venezuela. I would like to ask Mr. Sims if the iron ore at either or both of these places is such that it would lend itself to the manufacture of iron suitable for use in the turbohearth. C. E. Sims-—According to my information, those ores are not essentially different from ores now used in this country for making basic pig. They should, therefore, be adaptable to this process. D. I. Brown—You have spoken about the leeway, or spread in analysis of the various irons you can use in the vessel. I would like to have you tell us, if you can, about the different kinds of steels which can be made in such a vessel. The turbohearth process, or it might more aptly be called pneumatic openhearth, is a little different from that used in most Bessemer shops and in the one in which I worked. If we had a blow in the air over 10 min, the boss was in the pulpit in a hurry

Jan 1, 1951

By A. J. Jacobs

THE purpose of this note is to draw attention to a set of tables, recently compiled in Rocketdyne Research Report No. 64-19, under the title "Crystal-lographic Data for Indexing Cubic Twin Reflections and Cementite (Fe3C) Reflections in Electron Diffraction Patterns."' These tables were an outgrowth of electron-diffraction work conducted over the past several years on steels, precipitation-hardening aluminum- and nickel-base alloys, molybdenum, tantalum, and tantalum-base alloys. The first table lists the indices of possible twin reflections for all the possible twinning planes in bcc and fcc lattices. The twin reflections correspond

Jan 1, 1965

By G. Y. Chin, M. T. Dolan, W. L. Mammel

The least work analysis of constrained deformation, first proposed by Taylor and recently modified by Chin, Hosford, and Mendorf to include twinning, has been applied to the problem of axisynmetric flow. Calculations were made, for the case of (111}(110) slip and {111}(112) twinning applicable to fcc deformation. The solutions were obtained by linear programming techniques and with the aid of computer methods. The results show that in axisymnzetric tension the onset of twinning tends to decrease the plastic strength anisotropy as compared with the case of defortnation by slip alone. In compression, however, the strength anisotropy is increased as a result of twinning. The [100] and 11111 orientations and their vicinity are unfavorable for twinning in tension and compression, respecticely. With slight modifications, the present results may be applied to bcc metals deform ing by {110}(111j slip and (112} (111) twinning. Implications of present results to wire texture development of low stacking fault energy fcc materials arc discussed. PREVIOUSLY we' have applied linear programming techniques to obtain solutions to Taylor's least work analysis2 of constrained deformation of single crystals undergoing axisymmetric flow, such as occurs in an axially loaded polycrystalline aggregate. These solutions yielded values of the parameter M = o/.r = Y/w which relates the external stress-strain (u-c) curve to the shear stress-shear strain (7-y) curve for the crystal. The value of M is dependent on crystal orientation and hence enters significantly in texture strengthening considerations.3'4 Recently the Taylor hypothesis was modified by Chin, Hosford, and Mendorf' to include mechanical twinning. The latter has now been applied to the problem of axisymmetric flow and the results are reported in this paper. Calculations have been made for {111 )( 110) slip and {111 )(112) twinning applicable to fcc crystals. With minor changes in the indices of the slip and twin systems, the present results are also applicable to bcc crystals which slip on (110) (111) and twin on {112)(111) systems.

Jan 1, 1970

By L. E. Murr, P. J. Smith

A study has been made by transmission electron microscopy of thin foils of 304 stainless steel fatigued external to the electron microscope in reversed bending, and of thin foils fatigued directly within the microscope in alternating tension. The build-up of stacking faults in the thin foils during fatigue zoas correlated with the dislocatirm structures found in thin films prepared fror fatigued bulk specimens. The performance of the special devices designed for fatigue of thin foils so outlined and the importance of alternative methods of preparation of more uniform fatigue specimens bY vapor deposition are emphasized. INVESTIGATIONS on fatigued bulk aluminum1,' and stainless stee13j4 have revealed the existence of dislocation substructure on examination by transmission electron microscopy of electrolytically thinned foils representative of these bulk specimens. While this technique has proved extremely valuable, it has several shortcomings. First, the method of fatiguing bulk specimens and then thinning to foil for electron-transmission observation allows only one observation of internal structure at any one portion of the fatigue life. Second, thinning the bulk fatigued specimens to foil results in the loss of at least one original surface. Thus, what one sees in the remaining electron-transparent sections is an internal dislocation or fault structure which in many cases cannot be correlated with the original surface markings. This is an undesirable feature, since it is well-known that metal surfaces play an important part in the fatigue process.5 An obvious third undesirable feature of the thinning-from-bulk technique is the fact that static observations have difficulty (in the case of fatigue) explaining the mechanism of a dynamic process. What is required then is a method whereby a selected thin area can be continuously observed either while undergoing cyclic deformation or at various fixed stages of fatigue deformation. While Murr and wilkov6 have reported some success with an apparatus designed to fatigue thin metal foils directly within the electron microscope, the nature of the specimen-mounting procedure and the mechanical features involved in the adaptation of the fatigue device to the electron microscope make this method difficult to operate. It was not possible, for example, to make frequent observations of a selected area because of difficulty in maintaining a chosen area in a stable viewing position inside the electron microscope. Except for the build-up of a dislocation substructure and what are commonly referred to as "slip striations", little else has been reported from observations on thin-foil sections prepared from bulk fatigue specimens. segal17 has found "slip striations" in stainless-steel fatigued specimens which were electropolished from both sides, but gave no explanation as to their origin or identity in terms of lattice imperfections. The research to be reported in this paper was undertaken with the following objectives in mind. First, an attempt was made to devise a technique or techniques whereby thin metal foils could be fatigued and repeatedly observed by transmission electron microscopy. Second, it was hoped that some correlation could be made between deformation striations found in fatigued thin transmission specimens and thin foils prepared from bulk fatigued specimens. These investigations illustrate quite convincingly that a feasible method is available for the direct study of the fatigue mechanism and similar dynamic phenomena in thin transmission specimens inside the electron microscope. I) EXPERIMENTAL METHODS Three modes of specimen fatigue and observation of fatigue damage were used. These involved fatigue of thin-foil specimens in a special arrangement external to the electron microscope and observation of a selected area at various stages in the fatigue life, the fatigue of thin-foil transmission specimens inside the electron microscope, and the fatigue of bulk specimens external to the electron microscope followed by thin-foil preparation for direct observation at predetermined stages. Design of the External Fatigue Clip and Specimen Holder for the Hitachi H.U.11 Electron Micro-scope. The purpose of the fatigue clip was to provide a reversed bending fatigue stress to a thin-foil transmission specimen outside the electron microscope. In order to accomplish this, a flat-bottomed, U-shaped brass clip was made as shown

Jan 1, 1965

By C. T. Cox

The title of this short paper necessarily implies that friction articles comprise a distinct and unique field and are different from the other metal-powder articles, such as bearings, electrical contacts, and magnets. However, this distinction is rather hard to define in that it is really one of degree and not Of kind. It would appear that the main distinction is that friction are are articles of rather large pressing area. In other words, they are articles in which the area Of the mold in which the metal powder is pressed is relatively large. Other articles made from meta1 powders are generally of rather small area, usually a few square inches, while in friction articles the area ranges up to several hundred square inches. The satisfactory production of meta1-powder friction articles involves many production problems and a large number Of these are accentuated by the large area' Since it is impossible in the short space of this Paper to describe adequately all the problems involved, I have thought it best to merely mention some Of them and to place particular emphasis upon a problem that is common to all metal-powder articles, although it is of greater importance in the making of friction articles. This problem has to do with the effect On the properties of a friction article of small variations in the composition. However, before discussing the problems, it is probably appropriate that some mention be made of the limitations on the use of friction articles. Most engineers are familiar with the general field that can be characterized as constituted by clutch facings and brake linings, and undoubtedly have heard many stories of how metal-powder friction articles have had a service life 10 times as long as nonmetallic friction materials, and of instances where metal-powder friction articles have operated satisfactorily where no other material could be used. These instances should not be regarded as criteria for the assumption that metal-powder friction articles are capable of universal use in the friction field and will always outperform other materials. On the contrary, metal-powder friction articles are unsuitable for numerous applications, either on a performance or on a cost basis. Metal-powder friction articles will not replace wooden block brakes for wagon wheels nor cast-iron brake shoes for railway car wheels, to mention just two obvious examples. Metallic friction articles cannot be used where they must act as heat insulatorsl for they have a relatively high thermal conductivity as compared with asbestos. This is a detriment in some uses, as in certain airplane brakes having hydraulic actuators provided with rubber seals. The metallic friction material readily transfers the heat developed at the braking surface back through the material to the rubber seal and destroys it. Within its limited field, metal-powder friction material has proved satisfactory, but many problems are involved in the Selection of the proper material to use in an application and in the commercial pro-

Jan 1, 1945

By D. T. Camp, J. A. Clum

WITH experience, the indexing of back-reflection Laue patterns for cubic crystals is usually a straightforward matter. However, for noncubic systems where in general tables of interplanar angles are not available or when inexperienced personnel are involved, properly indexing a crystal is normally a tedious, time-consuming affair. The authors have written a digital-computer program which calculates and prints out a table of interplanar angles for an arbitrary crystal structure and then systematically searches through this table attempting to obtain a consistent fit to back-reflection Laue data supplied by the user. Of course it is possible simply to calculate a desired set of interplanar angles should this be the only requirement. The program was originally written in ALGOL for use on a Control Data G-21 computer and a preliminary version is described elsewhere.' A version in FORTRAN TV which has been run on an IBM 7040 and one in FORTRAN II run on an IBM 1620 are also available. While it is not the purpose of this communication to describe the program in detail, an indication of how the program operates may help one to decide whether the program would be useful under particular circumstances. The hypothetical example chosen involves the indexing of the zinc crystal which has a hexagonal structure and a c/a ratio of 1.856. Input data for this example consists of only nine cards: The first card controls the list of families of planes to be considered. If the Miller indices of a prospective family are (h k 1), the first digit places a limit, in this case 3, on the absolute values of any individual index. The second digit limits the sum (h +k + l + 1), in this case to 5. Therefore the families (013) and (112) are considered but the family (122) is not. All systems, including the hexagonal, are treated using three-digit Miller indices. The second card contains the crystallographic parameters required to define the system. The first digit is 0 if the system is rectangular, that is all angles are 90 deg. If the system is nonrectangular, as in this example, the digit 1 so indicates. The next three values are the lengths of the sides of the reference cell, a, b, c. The final three entries on the card are the angles, a, 8, y between the sides. The digit 0 on the third card indicates that more data follows, the digit 6 shows that a set of six planes is to be indexed, and the value 2.0 indicates that agreement between a tabulated angle and an input angle is considered adequate if their absolute difference is less than 2 deg. The fourth card lists the measured input angles. a12 = 38 deg, a13 = 24 deg, and so forth. More input angles are listed on cards five to eight with the latter giving the input angle 058 = 40 deg. The final card in this series indicates by the digit 1 that no more data is to be processed. The program operates in the following manner: 1) The input data from cards 1 and 2 is read, thereby indicating the crystal system to be examined and the crystallographic parameters of the particular crystal to be indexed. 2) A table of interplanar angles is generated. 3) The input angles contained on cards 4 to 8 are read. 4) The measured input data is systematically compared with the generated table of standard angles. All combinations of poles whose interplanar angles compare with the requisite, specified accuracy are printed out. If no adequate fit is found an indication of this is printed. A typical line from the generated table of interplanar angles is: (001) - (111) 74.92 64.99 It can be shown that in the Miller-Bravais system the first value corresponds to the angles between (0001)-(1121) and the second to that between (0001)-(1011). This particular set of data gave the following result for the planes 1 to 6: (011) (110) (121) (111) (112) (010) The ALGOL version also has the option of simply providing the Greninger-chart coordinates ? and 6

Jan 1, 1967

By M. E. V. Plummer, F. E. Beamish, J. C. Hole, J. M. Kavanagh

Prior researches have shown that the iron-copper-nickel content of platinum concentrates may be reduced by carbon to form a collecting alloy for the platinum metals in a manner exactly analogous to the formation of the lead fire assay button. The nature of the iron-copper-nickel alloys with the platinum metals has been investigated. Palladium and probably some of the other platinum metals form solid solutions with this alloy. ONE of the greatest known reserves of the platinum metals is to be found in the nickel, copper, iron sulphide deposits of Northern Ontario. The very large tonnage of copper-nickel ore processed makes the Sudbury district a significant world source of the platinum metals, the latter being recovered as byproducts in the electrolytic refining process for copper and nickel. Chalcopyrite, pentlandite, and pyrrhotite are carriers of the platinum metals;' these minerals contain from 0.03 to 2.0 ppm of the noble metals. The analysis of the above ores for the platinum metals necessitates an initial concentration of the minute quantities present in the ore. The method usually employed involves the extraction of the noble metals by molten lead with or without small proportions of silver. The lead is then separated from the precious metals by cupellation, a process which involves absorption by the cupel and volatilization of lead oxide, leaving the precious metals collected in a silver bead on the surface of the cupel. The collection by lead is probably achieved by a process of dissolution followed by some degree of segregation in the lead alloy since the cold button is seldom uniform in composition. With silver-lead alloys this process of liquation has been used to re- cover pure lead since, during the cooling period, crystals of pure lead separate and silver becomes concentrated toward the center of the solid.' Platinum and gold liquate in a manner similar to silver which may account for the successful recovery of platinum by fire assay even though it is considered insoluble in a solid lead medium. 3 In the case of iridium the liquation process may be a disadvantage in that the iridium may appear in the outer areas of the button and thus be lost mechanically during the handling processes. In any case the deficient alloying characteristics of lead for the platinum metals encouraged attempts to find an improved collecting alloy, and by analogy with aqueous extractions, preferably one in which solid solutions would be readily formed. Since, beyond a certain minimum solute to solvent ratio, the formation of a solid solution is accompanied by a lattice distortion, one would expect some relationship between the atomic diameters of any two metals and their tendency to form a solid solution. In one survey5 the hypothesis was put forward that when the atomic diameter of the solute differs by more than about 15 pct from the solvent, the "size factor" is unfavorable and the formation of a solid solution is restricted. On the other hand, when the atomic diameters are within this limit the size factor is favorable and solid solutions are readily formed, e.g. the transition metals of Group VIII having similar radii form solid solutions over wide ranges of composition.6 Even with a favorable size factor, elements having different crystal structures cannot form a continuous series of solid solutions. Cell dimensions alter as the concentration of the solute increases, causing a

Jan 1, 1962

By C. G. Dunn, J. L. Walter

The c/laracterzstics of cube-oriented nuclei ard other matrix grains that are associated with secondary, recrystallization to the cube texture in high-purity silicon iron were investigated by me-tallographic and X-ray methods. The results show that the structure consists of relatively perfect grains of average diameter between one and two times the sheet thickness ad that the texture has a moderately strong (110) [001] component and a weak (100) [001] component. The results also indicate that matrix stability results from the two-dimensional nuture of the graitzs and that cube-orzented nuclei are neither more Perfect nor larger grains than other matrix grains but have a preferred [001] direction in the rolling direction and have a more effective driving force for growth than other grains because of a low (100) surface energy. THE structures and textures of fine-grained rnatrices determine to a large extent the kinds of secondary recrystallization textures that form on annealing. The understanding of secondary recrystallization processes therefore depends on adequate information about the initial matrices. Matrices usually have three characteristics: 1) they consist of fine-grained primary recrystallization structures, 2) the fine-grained structures are stable toward normal grain growth, and 3) they contain secondary recrystallization nuclei. Stability toward normal grain growth may be due to either a strong single orientation texture (texture inhibition)' or a dispersed second phase (dispersed phase inhibition).2"4 If normal grain growth is not inhibited by either of these two factors, it nevertheless stops when the average grain size is between one and two times the sheet thick- ness.5 This thickness effect satisfies one of the characteristics of a matrix for secondary recrystallization. Its importance in the development of the cube texture in high-purity silicon iron by secondary recrystallization was pointed out by the authors in a recent paper on tertiary recrystallization7 and will be discussed further in the present paper. Assmus, Detert, and he8 have provided some information on a matrix for secondary recrystallization to the cube texture in silicon iron. They found a (110)[001] or Goss texture with enough spread about the rolling direction to include a small amount of the (100)[00l] orientation. The distribution of the [00l] directions was strongest parallel to the rolling direction for both (100) primaries and cube secondaries. These authors found no correlation between size of a matrix grain and orientation and concluded that some property other than size must be the distinguishing characteristic of the cube-oriented nucleus. No consideration was given, it

Jan 1, 1961