Search Documents

By Joseph W. Leonard

Evidence is presented to show that certain coals can be super-cleaned, using present coal preparation processes, to reduce sulfur below levels that are commonly believed to be possible. The evidence points to the need to develop continuous sorting methods by which coal coming from a mine can be segregated so that different raw coal types can be processed separately to produce a super-clean coal in addition to coals cleaned to more common levels of sulfur. Evidence is presented and techniques discussed that may be applicable for making the method feasible.

Jan 1, 1976

By B. E. Sundquist

The various methods based on solution models for obtaining free energies of mixing from miscibility-gap data have been applied to a number of binary-alloy systems. For nine of these systems there exist experimental thermodynamic data that permit a comparison of the results to experiment. It was found that the method of van der Toorn and Tiedema almost invariably leads to results that are physically unacceptable and that vary drastically with small changes in the miscibility-gap parameters. The subregular solution model is found in all cases, except the Al-Zn, Fe-Cr, and Cu-Pb systems, to exaggerate the free energy of mixing by 30 pct or more. The model developed by Lumsden is found to give results that are often in excellent agreement with experiment and which exaggerate the free energy of mixing by no more than 30 pct. These results and others give evidence that the Lumsden treatment of the effect of unequal atomic sizes and of imperfect configurational randomness due to deviations of AB bond energies from the mean of AA and BB bond energies is adequate for most systems. ANALYTIC expressions are frequently proposed for the dependence on composition of the activities of the components of a solution. Because the development of solution theory is incomplete, these expressions contain parameters which must be determined by experiment. The measurement of activities is often difficult and consequently such measurements are less readily available than are measurements of phase equilibria which, under certain conditions, can also be used to evaluate these parameters. For example, suppose it is known that two structurally dissimilar phases, each of known composition, in an n-com-ponent system are at equilibrium at a given temperature and pressure. n equations can be set up in terms of these parameters expressing the equality of the chemical potential of each component in the two phases. In addition, one can write the Gibbs-Duhem equation for each phase that also contains these parameters. Thus, if these n + 2 equations contain n + 2 parameters, these parameters can be determined (at the temperature in question) from the phase diagram alone. If the average number of parameters in each expression for the activity of a given component in a given phase is V then there will be 2nV parameters involved. Equating 2nV to n + 2 shows that, for n + 2, V = 1. If the temperature dependence of each parameter were to be expressed in some explicit form one could use equilibrium conditions at a number of temperatures to increase V. The situation is much improved when the two phases in equilibrium are structurally similar. It can then be assumed that, stably or metastably, two phases will become one at higher temperatures. Thus the number of parameters involved becomes nV instead of 2nV. Hence, V = 2 for n = 2 using only one temperature. (It is implied here that the activity expressions used are valid over the entire composition range.) In this investigation only the equilibrium of two structurally similar, two-component phases (miscibility-gap systems) will be considered. The various proposed solution models will be applied to a number of these systems and the results compared with available experimental results. All of the analytic expressions that have been proposed for the free energy of mixing of a two-component system are of the form where ?Gmix is the free energy of mixing per mole of solution, N1 and N2 are the mole fractions of components 1 and 2, respectively, and f(Ni, T) is some function of composition and temperature. In the "ideal" solution model f = 0. In the "regular" solution model f = a constant. Since these two models permit only a symmetric equilibrium diagram they will not be considered further here. The simplest model that permits a nonsymmetric miscibility envelope is the so-called "subregular" solution model proposed by Hardy.1 This model gives where the Ci(T) are functions of temperature only. The same expression for f is obtained from the "linear a function" model proposed by Darken and Gurry2 and applied to miscibility-gap systems by Wriedt.3 This model requires that the a function defined by be a linear function of composition (yi is the activity coefficient of component i). This model is not purely hypothetical for it has been found2 to hold true for a number of systems. It is readily shown3 that the f(Nl, T) obtained from this model is of the form given in Eq. [2]. It will be noted that the subregular solution model contains only two parameters and hence both of them can be determined at any desired temperature below the critical temperature, Tc, for a miscibility-gap systems in the manner described previously. At T, the two constants can be determined by equating the second and third derivatives of ?Cmix with composition to zero. Another two-parameter model was proposed by Lumsden4 who set

Jan 1, 1967

By J. W. Rutter, K. T. Aust

In previous studies of grain boundary migration in zone-refined lead, the authors used bicrystal specimens consisting of a striated crystal which was grown from the melt, and an adjacent striation-free crystal, introduced by artificial nucleation and growth.1 While this method permits the study of the motion of individual grain boundaries, it does not provide control of the relative orientations of the grains. The present note will describe a technique for controlling the orientations of the two crystals in this type of specimen. The technique consists essentially of placing a striated crystal and a striation-free crystal of controlled orientations end-to-end in a graphite trough, then melting a short zone at the junction of the two crystals and allowing it to freeze to form the desired grain boundary. The apparatus used to carry out this process is illustrated in Fig. 1. It consists of a trough milled from high-purity graphite,with grooves in the underside for the placement of thermocouples. The graphite piece fans out on one end at the level of the bottom of the trough; the sides of the trough are completed in this region by the attachment of a mating plate with a slot cut at any desired angle to permit reorientation of the crystal placed at this end of the assembly. The joint between the crystals is made at or near the point where the slotted plate joins the rest of the trough. The thermocouple slots are deepened in this region so that the thermocouples are separated from the melt by only 1/32 in. of graphite. An induction heater, with suitable temperature control, is used to obtain the molten zone. The two single crystals used are first chemically polished in a solution consisting of eight parts glacial acetic acid and two parts 30 pct hydrogen peroxide. They are then placed in the trough with the ends to be joined at the position of the thermocouples. Next, cooling is applied to the two crystals by means of air

Jan 1, 1962

By J. W. Whalen

The design, operation and evaluation of an instrumental method for the determination of fluid saturation in porous materials during multiphase flow studies is described. The presence of a magnetic tracer comprising approximately 20 per cent by weight of the aqueous phase is necessary in the utilization of this method. The results of two-phase relative permeability studies on two samples of porous media are presented. The realizable accuracy of the magnetic susceptibility apparatus in fluid saturation determination is estimated to be 2 saturation per cent. The response characteristics of the instrument, together with its simplicity of operation and maintenance are sufficient to recommend its use in routine laboratory studies. INTRODUCTION The problem of fluid saturation determination in laboratory multiphase flow studies characterizing oil recovery processes is one which has been given exhaustive study. Briefly the requirements which are considered essential for a method sewing this purpose are: (1) that the measurement be made external to the porous rock sample under study with no interruption of the fluid flow pattern, (2) the saturation indication must be independent of fluid distribution in the volume scanned by the measuring device, (3) the sensing element should have a small field of definition enabling several independent measurements to be made along the length of a core sample, and (4) the properties of the fluid phases should not be too greatly influenced by required tracer substances. Several methods of saturation determination have found acceptance as meeting most of the above requirements. These include resistivity,1 X-Ray absorption,2,3,4 radiotracers,5,6,7 and neutron8 diffraction The merits of these techniques have been discussed elsewhere in detail and will not be considered here. It may, however. be pointed out that the elaborate instrumentation required by the methods mentioned above, with the exception of the resistivity method (which is undesirable from other standpoints) encourages the development of methods of saturation determination which, while meeting the requirements listed, are simple to operate and maintain. It is the purpose of this paper to describe the instrumentation and evaluation of a technique for the determination of fluid saturation which combines relative simplicity with an accuracy and applicability comparable with methods now in practice. DESCRIPTION OF THE METHOD If the magnetic susceptibility of one of the fluid phases contained within a porous material is sufficiently greater than that of the remaining phases, the fluid content of the material with respect to that phase may be determined by an induction measurement. This may be accomplished by measuring the induced voltage in the secondary of a transformer which contains the porous sample and its interstitial fluids as a portion of the magnetic flux path. Since the fluids used in multiphase flow studies involving petroleum reservoir samples possess uniformly low magnetic susceptibilities, the use of a magnetic tracer in one of the fluid phases is required. In view of the relatively high paramagnetic susceptibility of salts of the transition elements, together with their high water solubility. these compounds become logical choices as tracer materials. Cobaltous chloride, having a specific magnetic susceptibility of 17.5 x 106 cgs electromagnetic units, was used as the tracer material throughout this work, in a concentration of approximately 20 per cent by weight in the aqueous phase. MAGNETIC SUSCEPTIBILITY APPARATUS Basically, the magnetic susceptibility apparatus consists of a transformer serving as the detecting head, a

Jan 1, 1955

By R. Maddi, I. R. Kramer

C. S. Roberts (Dow Chemical Co., Midland, Mich.)— In this study we have seen another example of how modern electronic instrumentation can be of great value to metallurgical research. The authors have shown much ingenuity in their experimental work. However, I wish to point out that anelasticity theory tells us that we must be cautious when we use pulse methods for measurements which are to be correlated with knowledge of static stress-strain behavior. The basic stress calibrations used by the authors depend on the use of static moduli combined with the pulsed strains. No recognition of a possible modulus defect has been indicated. The general agreement of critical resolved shear stresses may indicate that a

Jan 1, 1953

By B. M. Larsen, T. E. Brower

An increasing amount of attention is being paid to the possible influence of oxygen, in its several modes of occurrence in steel, upon some of the properties of the metal; but clearly investigations along this line are unlikely to yield significant results until reliable analytical methods for the determination of oxygen have been established. This paper presents some results of a study of an improved Ledebur method which aims to determine a definite portion of the oxygen; namely, that which presumably is present in diffusible form in the solid steel. These more or less preliminary results lead us to believe that the oxygen so determined has some significance; their presentation at this time will, we hope, stimulate discussion of, and focus attention upon, certain rather neglected aspects of the problem. Considerable work has been done recently on methods of estimating inclusions and on the vacuum-fusion method for oxygen; with results which, however, are of somewhat questionable significance. It is commonly presumed that the oxygen in a bath of molten steel in a furnace is present partly as a separate phase consisting of suspended particles of oxides or silicates, partly in solution, the latter being probably the more important. Upon addition of a deoxidizer, it reacts with some portion of the dissolved oxygen and precipitates it as additional suspended particles; the oxygen not eliminated in this way, which remains in solution in the liquid steel, may be regarded indifferently either as dissolved oxygen or as dissolved FeO. When the steel is poured, some of the suspended particles rise towards the surface, others remain trapped in the finished steel, appearing as nonmetallic inclusions in amounts corresponding usually to about 0.01 to 0.03 per cent Oz in the steel. The dissolved oxygen may be partly eliminated as CO during freezing of the ingot, but some remains either in solution or in part precipitated as FeO. Finished steels may thus contain oxygen in several forms: (1) In non-metallic inclusions which are probably quite insoluble in the solid metal at all temperatures; (2) in solid solution which at lower temperatures may be supersaturated; (3) in FeO particles produced by relief of this

Jan 1, 1932

By H. C. H. Darley

Particles of montmorillonite-type clays consist of plate-like clay crystals stacked face to face. Under certain conditions in a suspension, these particles disperse to individual platelets with the formation of diffuse double layers round each platelet. This action has a profound influence on the rheo-logical and other properties of the suspension. This paper describes a test for degree of dispersion and uses this test to correlate changes in dispersion with changes in viscosity and gel strength. The test is of practical value in determining and controlling dispersion in drilling muds. INTRODUCTION It has long been recognized that the hydration and dispersion of clays, particularly those of the montmoril-loilite type, strongly influences the rheological and other properties of drilling muds, but little has been done to measure either of these phenomena under conditions that exist in drilling muds. The hydration of clays as such has been extensively studied by those interested in clay mineralogy, but in drilling muds it is to be expected that dispersion is at least as important a factor as hydration because of the much higher water-to-clay ratios and the very high degree of mechanical agitation. The term dispersion as generally applied to colloidal systems means the subdivision of large particles to small. Particles of montmorillonitic clays, however, consist of plate-like particles stacked face to face. Dispersion of these aggregates to individual platelets may be expected to have an unusually large influence on the properties of the suspension because of the shape factor, the enormous increase in specific surface, and the pronounced surface phenomena exhibited by the crystal surfaces. It is this form of dispersion that is particularly considered in this paper, -and the term degree of dispersion is used to imply the number of platelets per particle. The term aggregation is used to denote the opposite of dispersion, the association of individual platelets face to face to form stacks. It is important, as Garrison' has pointed out, to distinguish between the deflocculation-flocculation phenomenon and the dispersion-aggregation phenomenon. Flocculation of clay suspensions is characterized by the formation of voluminous sediments that are stable under quite high centrifugal fields. This indicates an edge to plate association of particles to form an open network type of structure, which obviously will have quite a different influence on the properties of the suspension than aggregation of the platelets face to face. The work described in this paper was primarily concerned with developing a test for degree of dispersion in clay suspensions and by means of this test to follow changes of dispersion brought about by addition of electrolytes and to show the influence of dispersion on the rheological properties. The Clay-Volume Test This test is based on the assumption that the greater the number of particles per unit weight of clay in a suspension the greater will be the volume of sediment when it is flocculated under standard conditions and centrifuged. After considerable experimentation the following procedure was established: 1 cc of the test mud vigorously shaken with 100 cc of 1-N NaCl in an ASTM oil centrifuge tube and centrifuged for five minutes in an International No. 2 centrifuge at 2,000 rpm. When drilling fluids of different solids content are being compared, the clay volume is expressed in cc per gram of clay solids, but generally changes in dispersion in a given mud are being compared and it is more convenient to report as cc of sediment. The test is strictly a comparative test, so that it is not necessary to adhere to the conditions specified above, e.g., with field muds a stronger flocculant such as Al2(SO4)3 may be preferable to NaCl.

Jan 1, 1958

By Tuncel M. Yegulalp, Peter G. Zambas

In planning an underground room-and-pillar mine, the selection of the shaft or portal location and the orientation of the main haulage arteries is of paramount importance, particularly in view of the high dependence of the cost of truck haulage on the proper definition of these parameters. In an effort to facilitate this selection a computer program was written which, by relating the truck characteristics to the areal configuration of the property or ore body, derives the volume-weighted total fuel and time requirements for hauling ore from every panel within the property to a specified portal or shaft location through a predetermined gridwork of haulage drifts. By varying the size and orientation of the gridwork and the location of the portal or shaft access, an infinite number of configurations can be investigated. The results of this analysis can be plotted to indicate the optimum conditions.

Jan 1, 1974

By Eckley B. Coxe

THE plummet lamp, to which I called the attention of the Institute, at the Bethlehem meeting, in August, 1871, with the improvement of the compensating ring, suggested by Mr. Heller, having come into general use for mine surveying in this country, and my attention having been called to the fact that it could not be employed in mines in which there was danger of meeting with fire-damp, I have so modified it that it can be used in all cases with safety. Mining engineers, who are in active practice in those districts where fire-damp is met with in the mines (and I am sorry to say it is becoming much more common in the anthracite regions), know how dangerous their work is when they are called upon to survey such mines, particularly when they are obliged to run lines in those parts of a mine which have been unworked, since by opening of doors, brattice, etc., to get the sights, they are liable to disarrange the currents of air, and cause any fire-damp that may have accumulated in the old workings to find its way into the levels, etc., where the party is at work. It is, therefore, very dangerous to leave an open light (such as the original form of plummet lamp) in an old breast or gangway, even when the safety lamp has shown that no fire-damp is present, for the opening of the doors, etc., may drive the fire-damp to the light, and thus endanger the lives of the engineers. The improved form of plummet lamp, now shown to you, can be used either with or without the safety apparatus. Upon the top of the plumb-bob portion of the old lamp a screw is cut, upon which a ring A is screwed. (See Plate II.) On the external cylindrical part of this ring two small conical holes are drilled, 180° apart. The compensating ring, by which the plumb-bob part of the lamp is suspended, passes over the ring A, and is fastened to it by two small screws having conical points, which fit into the conical holes in the ring A. The safety apparatus resembles, to a certain extent, that of the Mueseler lamp. It consists of a ring B and plate C, which are united by four rods. The plate C has a cylindrical hole in the middle, and four apertures distributed radially around it. In the central cylindrical hole is fitted a conical brass chimney, which projects below the plate C, and is fastened to the latter, being kept ver-

Jan 1, 1875

By H. D. Outmans

The author applies the theory of hydrodynamic stability to fluid flow in porous media and concludes that the displacement of miscible liquids is stable if the stability coefficient, as defined by Eq. 19.2 or Eq. 27.0, is positive. The conclusion is invalid, however, since it is based on a faulty argument. To demonstrate this, the reader is referred to Eqs. 4.1 through 4.5 of the paper which describe, in differential form, the first-order disturbances c, u, v, w and p. In these same equations, cx, cz, gl, g3 and are functions of the stable concentration c. This concentration c is known and depends on x, z and t (the author assumes cy = 0). It follows that cx, cz, gl, g3 and µ are also functions of x, z and t. With this in mind, we turn to Eqs. 8.1 through 8.5 which were derived from Eqs. 4.1 through 4.5 by substituting Eq. 6.0. The significance of this substitution is that the author thereby limits the solutions of Eqs. 4.1 through 4.5 to equations of the form of Eq. 6.0. Eqs. 8.1 through 8.5 represent an infinite linear system with five unknowns: c, u, v, w and p. The coefficients cx, cz, gl, g3 and µ in this system are known at each point and at each instant; the coefficients containing derivatives of f are unknown. If this infinite linear system in c, u, v, w and p is to have a nontrivial solution, then it is indeed necessary (as the author states) that the determinant of the coefficient matrix of Eqs. 8.1 through 8.5, i.e., ( A 1, be equal to zero. This condition, however, is not sufficient. A non-trivial solution exists if, and only if, the rank of the coefficient matrix of the entire infinite system is smaller than five. In other words. all minors of order five must vanish and only if all the coefficients in Eqs. 8.1 through 8.5 are constant is this equivalent to the condition |A| =0. Constant coefficients means that gl, g3 and µ, for instance, are constant; and, since they depend on c it follows that c must be constant. We conclude that the condition I A I = 0, on which the author bases his calculations, is necessary and sufficient for a nontrivial solution only if the concentration c is constant. In other words, the author does not investigate the stability of a miscible displacement but, rather, only the stability of the flow of a homogeneous liquid. Using the initial condition and the fact that the coefficients are constant, we find

By R. D. Fisher, A. G. Metcalfe, F. A. Crossley

AN investigation of the application of magnetic stirring to the consumable arc melting of aluminum and nickel demonstrated that grain refinement could be obtained when there was sufficient stirring force. Also, it was found that grain refinement could be obtained in aluminum by alternately reversing the polarity of the current through the magnetic stirring coil. The effect of the latter was to periodically reverse the direction of rotation of the molten metal.' Because of their promise, these findings were applied to conventionally cast aluminum. Shortly after this work was begun, Kondic2 reported experiments in which aluminum cast with 40° C (72° F) of superheat exhibited a grain size of 10 to 20 grains per cm2. When interrupted rotation was applied during solidification by mechanical means, a grain size of 800 to 1000 grains per cm2 was obtained. Magnetic Stirring Applied to Conventional Casting— The applicability of magnetic stirring to producing grain refinement in conventionally cast metal was evaluated in the following way. Three pounds of aluminum were cast into a clay-bonded graphite mold. The mold was surrounded by a magnetic stirring coil of 1000 turns. A direct current of 200 amp was passed through the casting by means of a graphite electrode which was immersed from the top. A current of 5 amp was passed through the stirring coil. The aluminum (1100 or 25) was superheated to 1600° F (871° C) and fluxed by passing chlorine gas through the melt for 2 min prior to casting. Two additional castings were made for comparison: 1) a conventional casting of metal superheated to 1600° F and 2) a similar casting through which 200-amp current was passed during solidification, but without current in the magnetic coil. Macrosections of these three ingots are shown in Fig. 1. Very remarkable grain refinement resulted in the magnetically stirred casting. It may be noted that the casting through which 200-amp current was passed has a coarser structure than the conventional casting. It would appear that this is due to the additional heat input generated by the current to the former casting. Mechanical Rotation Applied to Conventional Casting—A casting temperature of 1600° F was used throughout. Some 1 1/2 -lb castings rotated at 150 rpm were predominantly columnar with small areas of coarse, equiaxed grains close to the lower mold wall. Following these, a series of 3-lb castings was made. Macrosections of these ingots are shown in Fig. 2. The imposed rotational speed was 250 rpm. Turbulence or acceleration in the solidifying liquid was the significant factor. Fine grain size resulted in the material solidified during the period of acceleration of the liquid to the imposed rotational speed. When uniform rotational motion was achieved, the grain structure reverted to columnar. The final casting shown in the lower right-

Jan 1, 1962

By Walter Rose

Experimentation which measures differences in pressure across the interfaces of immiscible fluids in the interstitial spaces of porous media may be termed "capillary pressure experimentation". In the literature of petroleum technology since 1941 there have appeared twelve papers popularizing capillary pressure concepts and developing applications of these concepts for the solution of problems of practical reservoir engineering importance, such as the determination of connate water, fluid distribution. in transition zones, reservoir rock textural properties, and oil recovery from petroleum reservoirs. Although a review of the literature would be justified at this time in order to reconcile the conflicting viewpoints which are contained in the cited papers, the object of this note will be of more limited scope. It is believed that the recent paper of Muskat alls sufficient attention to many of the uncertainties which arise upon examination of the published literature. such that until satisfactory counter-proposals can be made it will serve our purpose only to mention some other like uncertainties. This will emphasize further the need confronting petroleum technologists to re. consider and reformulate the application possibilities of capillary pressure experimentation. In particular, I sug- gest that we examine the thesis that capillary pressure experimentation as above defined can lead to measurements reflecting the recovery of oil from petroleum reservoirs, as was proposed first" by Amyx and Yuster and was first reduced to practice by the experimentation of Welge . In fact. I shall deal exclusively with the Welge papers since it is the principle one on this subject which has appeared to date. I shall attempt to show that the possibility of describing oil recovery features in terms of capillary pressure phenomena has not been established entirely. The Welge paper was a pioneering effort to evaluate this recovery application possibility. P. P. Reichertz' comments on the Welge paper state that non-wetting phase discontinuities are developed occasionally in the Welge experiment, and restate Muskat's argument that discontinuous fluid elements (partially saturating the interstices of porous media which are elsewhere saturated with some other immiscible phase or phases) are not subject to the requirements of hydrostatic equilibrium. It is the purpose of my comment to show that it is unnecessary to make Reichertz' postulation regarding non-wetting phase discontinuities (however valid) when it is desired to criticize Welge's theoretical treatment of his problem. It can be shown that Welge's method of measuring values for ''capillary pressure" is invalid in many instances of application, such that his reported curves of capillary pressure Versus fluid saturation often have no physical meaning, even throughout the interval of fluid saturation where it might be otherwise suspected that no phase discontinuities occur. By considering established principles of capillary pressure experimentation it can be shown that the pressure difference experimentally observed between wetting and non-wetting fluid phases which are contained in external reservoirs will reflect on the capillary pressure difference at the interfaces of contact between these phases only when the following conditions are satisfied: (a) There shall be a balance between the opposing forces of gravity and capillarity, as obtains under conditions of hydrostatic equilibrium when the positions of the interfaces of contact become fixed in pore spaces of certain geometry (b) The wetting and non-wetting fluids within the interstitial spaces shall everywhere be continuous with the external wetting phase reservoir and the external non-wetting phase reservoir, respectively. It will become apparent immediately that in any instance when a greater pressure is recorded in the external wetting phase reservoir than in the external non-wetting phase reservoir, one may establish either that static equilibrium has not been attained or that discontinuities in one or more of the fluids have been developed. This is because the pressure otherwiee is always gereatest in the non-wetting phase at each static interstitial interface of contact with the wetting phase. such that the externally measured pressure in the non-wetting phase likewise must be greatest if the above conditions are to be satisfied.

Jan 1, 1949

By Walter Rose

Experimentation which measures differences in pressure across the interfaces of immiscible fluids in the interstitial spaces of porous media may be termed "capillary pressure experimentation". In the literature of petroleum technology since 1941 there have appeared twelve papers popularizing capillary pressure concepts and developing applications of these concepts for the solution of problems of practical reservoir engineering importance, such as the determination of connate water, fluid distribution. in transition zones, reservoir rock textural properties, and oil recovery from petroleum reservoirs. Although a review of the literature would be justified at this time in order to reconcile the conflicting viewpoints which are contained in the cited papers, the object of this note will be of more limited scope. It is believed that the recent paper of Muskat alls sufficient attention to many of the uncertainties which arise upon examination of the published literature. such that until satisfactory counter-proposals can be made it will serve our purpose only to mention some other like uncertainties. This will emphasize further the need confronting petroleum technologists to re. consider and reformulate the application possibilities of capillary pressure experimentation. In particular, I sug- gest that we examine the thesis that capillary pressure experimentation as above defined can lead to measurements reflecting the recovery of oil from petroleum reservoirs, as was proposed first" by Amyx and Yuster and was first reduced to practice by the experimentation of Welge . In fact. I shall deal exclusively with the Welge papers since it is the principle one on this subject which has appeared to date. I shall attempt to show that the possibility of describing oil recovery features in terms of capillary pressure phenomena has not been established entirely. The Welge paper was a pioneering effort to evaluate this recovery application possibility. P. P. Reichertz' comments on the Welge paper state that non-wetting phase discontinuities are developed occasionally in the Welge experiment, and restate Muskat's argument that discontinuous fluid elements (partially saturating the interstices of porous media which are elsewhere saturated with some other immiscible phase or phases) are not subject to the requirements of hydrostatic equilibrium. It is the purpose of my comment to show that it is unnecessary to make Reichertz' postulation regarding non-wetting phase discontinuities (however valid) when it is desired to criticize Welge's theoretical treatment of his problem. It can be shown that Welge's method of measuring values for ''capillary pressure" is invalid in many instances of application, such that his reported curves of capillary pressure Versus fluid saturation often have no physical meaning, even throughout the interval of fluid saturation where it might be otherwise suspected that no phase discontinuities occur. By considering established principles of capillary pressure experimentation it can be shown that the pressure difference experimentally observed between wetting and non-wetting fluid phases which are contained in external reservoirs will reflect on the capillary pressure difference at the interfaces of contact between these phases only when the following conditions are satisfied: (a) There shall be a balance between the opposing forces of gravity and capillarity, as obtains under conditions of hydrostatic equilibrium when the positions of the interfaces of contact become fixed in pore spaces of certain geometry (b) The wetting and non-wetting fluids within the interstitial spaces shall everywhere be continuous with the external wetting phase reservoir and the external non-wetting phase reservoir, respectively. It will become apparent immediately that in any instance when a greater pressure is recorded in the external wetting phase reservoir than in the external non-wetting phase reservoir, one may establish either that static equilibrium has not been attained or that discontinuities in one or more of the fluids have been developed. This is because the pressure otherwiee is always gereatest in the non-wetting phase at each static interstitial interface of contact with the wetting phase. such that the externally measured pressure in the non-wetting phase likewise must be greatest if the above conditions are to be satisfied.

Jan 1, 1949

By Harry J. Morgan

One of the greatest improvements in drilling equipment has been the development of hard facing metals which are welded by electricity or by acetylene to form a facing which protects the steel of the bit from abrasive wear. The main desirable characteristics of hard facing metals are resistance to abrasive wear, resistance to shock and perfect bond with underlying metal. Resistance to abrasion offered by various metals shows many anomalies. Compounds containing carbon, silicon and boron are the most important hard substances. Carbon, as diamond, silicon carbide and especially the carbides of iron, chromium and tungsten are the outstanding hard products in common use. Tungsten carbide is probably the most commonly used. It is made in the electric furnace and it is important to get the right amount of carbon and the correct crystalline structure in order to obtain the greatest hardness and greatest resistance to abrasion. It may be obtained in three main divisions: wrought, cast and casehardened. Insert hard metals are common. The method of application varies, but it is generally welded to the bit, placed in channels or in drilled holes and covered with a hard surfacing metal. Robinson' has given a very complete article on the use of inserts. Gregg and Küttner2 has discussed the metallography of tungsten carbides and given a good bibliography of the subject,. The time and expense of large-scale testing, together with variations in results, led to the development of a laboratory testing machine for determining the abrasive-resisting qualities of different metals. This machine consists of a motor-driven 40-grain, alumina-base corundum wheel, 8 in. dia., rotating at 30 r.p.m. It is run wet and dressed with

Jan 1, 1930

By Norman D. Fitzgerald

The growth of domestic requirements for motor fuel has been phenomenal, rising year after year in a fashion almost unique among commodities, resisting depressions and forging rapidly ahead in times of prosperity. Consumption advanced from 226 millions of barrels in 1925 to 522 millions of barrels in 1938; or 130 per cent. The economic influences generating and sustaining this demand are of vital concern to the petroleum industry. The general factors affecting utilization of motor fuel are well known but it is the purpose of this paper to employ the recently developed technique of economic dynamics to describe them mathematically. Such problems in economic analysis are complicated by the freedom of all the variables to fluctuate, their mutual interdependence, changing incidence upon one another, and the nonquantitative character of some of them. Economic quantities and relationships, unlike those of the physical world, are continuously changing and this dynamic characteristic is both a distinguishing and confusing feature in economic research. The complexities of the problems require application of the analytical devices of mathematical statistics to uncover the probable relationships between factors. The procedure employed is to formulate a logical relationship linking the dependent to the independent variables, and then simultaneously, rather than sequentially, determine their separate effects by multiple correlation. This transformation of common knowledge to quantitative terms makes it possible to measure the probable effects of changing conditions upon requirements, assisting in the sound interpretation of economic policies. The utility of the results of such dynamic analysis is in sharp contrast to the sterility of the trends and other simple empiricisms of descriptive statistics. It is not intended in this study to throw light on the reasons why any motor fuel at all is consumed; but to discover relationships explaining why more was consumed at one time than at another. Specifically the problem is confined to the measurement of the influences of statistically

Jan 1, 1940

By Norman D. Fitzgerald

The growth of domestic requirements for motor fuel has been phenomenal, rising year after year in a fashion almost unique among commodities, resisting depressions and forging rapidly ahead in times of prosperity. Consumption advanced from 226 millions of barrels in 1925 to 522 millions of barrels in 1938; or 130 per cent. The economic influences generating and sustaining this demand are of vital concern to the petroleum industry. The general factors affecting utilization of motor fuel are well known but it is the purpose of this paper to employ the recently developed technique of economic dynamics to describe them mathematically. Such problems in economic analysis are complicated by the freedom of all the variables to fluctuate, their mutual interdependence, changing incidence upon one another, and the nonquantitative character of some of them. Economic quantities and relationships, unlike those of the physical world, are continuously changing and this dynamic characteristic is both a distinguishing and confusing feature in economic research. The complexities of the problems require application of the analytical devices of mathematical statistics to uncover the probable relationships between factors. The procedure employed is to formulate a logical relationship linking the dependent to the independent variables, and then simultaneously, rather than sequentially, determine their separate effects by multiple correlation. This transformation of common knowledge to quantitative terms makes it possible to measure the probable effects of changing conditions upon requirements, assisting in the sound interpretation of economic policies. The utility of the results of such dynamic analysis is in sharp contrast to the sterility of the trends and other simple empiricisms of descriptive statistics. It is not intended in this study to throw light on the reasons why any motor fuel at all is consumed; but to discover relationships explaining why more was consumed at one time than at another. Specifically the problem is confined to the measurement of the influences of statistically

Jan 1, 1940

By C. V. Milikan

Allocation of allowed production in a prorated field by the use of bottom-hole pressures is a method which is sound in theory. Thus far it has had limited application because the experience in correlating bottom-hole pressures with the depletion of wells or fields is not sufficient to interpret all the pressure changes. With additional data and more general knowledge of bottom-hole pressures their use in proration will probably become common. Bottom-hole pressure is the pressure at or near the bottom of a well. It is usually determined at the face of the producing horizon. Bottom-hole pressure measured while the well is producing, may be called the bottom-hole producing pressure or bottom-hole flowing pressure. If the well has been shut in or shut down long enough for the pressure in the producing horizon within the drainage area of the well to equalize, it may be called the reservoir pressure. The allowable production from a prorated field may be allocated to the individual wells or leases by three methods: 1. Bottom-hole producing or flowing pressures. (a) The potential capacity of a well to produce. (b) A uniform differential pressure while producing at the allowed rate. 2. Reservoir pressures. 3. A combination of bottom-hole producing pressures and reservoir pressures. In most prorated fields the allowed production is allocated to the individual wells or leases in proportion to their individual potentials. This method is based on the theory that there is a direct relationship between the permeability and the porosity of the reservoir. More directly stated it means that there is a direct relationship between the amount of oil in the reservoir and the rate at which it will move through the reservoir. While in general this relationship is true, it may vary considerably in different wells. Furthermore, in many wells the capacity of the reservoir to deliver oil to the well is greater than the capacity of the flow string to deliver oil to the surface. It is especially true where the potential is determined by flowing through tubing or by pumping.

Jan 1, 1933

By Alfred E. Hunt

The charge to be described was made in a seven-ton furnace, with a hearth twelve feet long and eight feet wide, with three gas and three air ports on each side. The stock of the entire heat was charged cold in one hour and five minutes, a part of the pig being first placed upon the bottom to protect it, then upon it the plate-scrap and blooms, and finally the remainder of the pig—some two thousand pounds. In fire hours and twenty-five minutes after beginning the charge the metal was melted down level, and two hundred pounds of hot twelve-per cent. spiegel was charged, care being taken to have it entirely immersed in the bath. In two hours more the bath was thoroughly melted and hot, and began to boil, i. e., the carbon began to be oxidized and evolved through the bath of covering slag as carbonic acid and carbonic oxide gases. Seventy-five pounds of lumps of Republic specular iron ore were added at this time, increasing the action, so that in ten minutes after the metal was in active ebullition. A test of the metal showed it to have about 0.90 per cent. carbon. One hour after the first ore was added a test was again taken, after thorough rabbling of the metal, and it was found to be 0.37 per cent. carbon. One hundred pounds more of lump Republic ore and about seventy-five pounds of limestone were then added, and fifty minutes later, after the bath was thoroughly rabbled, a -test showed the metal to have 0.23 per cent. carbon. Twenty-five pounds more of Republic iron ore were added and the metal allowed to boil for twenty minutes, when a test, after rabbling, showed the carbon to be 0.18 per cent. and the manganese to be 0.01 per cent.; the slag fracture was vitreous and of a very dark-green color. About forty pounds of limestone were added, and, the metal being hot and in a state of quiet ebullition, a hickory pole of twelve feet length and about four inches diameter, was run through the aperture in the centre door and held in a steady inclined position in the bath, with the end touching the bottom, the pole being shoved in further as it was burned away. The bath was carefully watched to see that the action that ensued was not too violent, the pole being several times

Jan 1, 1884

By D. H. Polonis, Gary A. Dreyer

This investigation involved a study of the reactions occurring during aging of supersaturated a phase in a CIL-Si alloy. The aging processes at temperatures below 552°C were studied by means of metallography, microhardness, and electrical resistivity measurements. During the initial stage of aging in the temperature range 275o to 525oC an anisotropic phase, which is visible in the form of striations in the micro-structure formed prior to the appearance of the -phase. This transition phase has been designated k' due to its structural similarity to the k phase. The rate of K' formation during aging increased with aging temperature. At 450o and 525°C the reaction appeared to reach completion before significant amounts of precipitation were observed. The overall precipitation reaction in this system involved four stages: formation of formation of at a grain boundaries, growth of particles in 7-egions, and coagulation of into large particles. The relative role of each of these processes is dependent on the temperature of aging. The formation of phase from supersaturated a during aging increases the electrical resistivity and slightly increases the hardness of a 4.9 pct silicon alloy. The formation of during aging decreases the electrical resistivity and increases the hardness until coalescence of particles begins during the final stages of aging. The coalescence of results in a decrease of both electvical resistivity and hardness. THE available literature does not record a detailed analysis of the aging processes in Cu-Si alloys. Such an analysis has been difficult due to both the limited data available and misleading microstructural observations which have been reported. Previous work suggests that a rather complicated series of processes may be involved in the aging of supersaturated a. The present investigation is concerned with an analysis of the sequence of these aging processes in a 4.9 pct Si alloy. The currently accepted version of the Cu-Si equilibrium diagram, Fig. 1, was published by C. S. Smith in 1940.' This diagram shows a eutectoid at 5.2 pct Si with the high temperature phase, having its composition range entirely to the right of this value. By quenching alloys in the composition range 4.6 to 5.2 pct Si from the region, Smith was able to retain the phase. However, this phase exhibited a striated microstructure which was anisotropic to polarized light. These striations were suggested by Smith to be duplex twins. Using an oscillating crystal X-ray method Barrett2 studied alloys containing 4.0 to 5.4 pct Si quenched from the and regions. The striations observed in quenched specimens were attributed by Barrett to quenching stresses. He found that striations could also be formed by deformation after quenching and identified them as stacking faults in alloys containing 4.0 to 5.0 pct Si. Barrett related the striations in alloys containing 5.0 to 5.4 pct Si both to stacking faults and to a metastable phase which he called The striated structure reported by smith' was also obtained by Hoffmann, et al. 3 By deeply etching their specimens the anisotropic phase on the surface was removed, leaving a structure which was microscopically similar to pure copper. By means of X-ray analysis before and after deformation at room temperature it was concluded that the anisotropic phase was metastable This conclusion has been questioned by Barrett who attributes the discrepancy to superposition of k and lines on the powder patterns of Hoffmann, et alm3 The decomposition of supersaturated according to smith' and Anderson,4 is very sluggish. However, Nony and Dreyer,5 and Hoffmann, et al.' found that deformation increases the rate of decomposition. X-ray studies by Hoffmann, et al on

Jan 1, 1962

By W. S. Ayres