Search Documents

By K. E. Starling

Phase equilibria data were used to develop an equation-of-state correlation for complex hydrocarbon mixtures, thereby circumventing difficulties associated with use of pressure-volume-temperature data. Equilibrium phase data for two condensate reservoir fluids were used to determine equation-of-state parameters for hydrocarbons as heavy as C22H46 in a modified form of the Benedict-Webb-Rubin equation of state. Comparative tests of K-values from the resultant correlation were made with data for condensate reservoir, separator and gas plant absorber mixtures. Generally, for temperatures above OF and computed liquid densities below 0.55 Ib-mole/cu ft, the modified BIVR equation predicted K-values in close agreement with the experimental data. INTRODUCTION Accurate predictions of thermodynamic behavior for complex hydrocarbon mixtures are necessary for many calculations in the petroleum industry. Because of the relatively high cost of extensive experimental data, many correlations for prediction of phase behavior have been developed. Some of these, such as the correlation of K-values presented in the NGAA Equilibrium Ratio Data Book, are totally empirical.l Others, such as the Benedict-Webb-Rubin (BWR) equation-of-state method, are semitheoretical.2-4 Unfortunately, published correlation methods often do not accurately predict the phase behavior of complex hydrocarbon mixtures, principally because of inadequate representation of the effects of components heavier than decane. This paper presents a new approach to this problem in which basic equation-of-state relations including heavy hydrocarbon effects are applied. Equilibrium phase data for two condensate reservoir fluids containing hydrocarbons as heavy as C22H46 are used to correlate component K-values. The BWR equation was chosen as the prototype equation of state for this study because of its proven capability for accurately predicting phase behavior and thermodynamic properties of light - hydrocarbon mixtures? Research was directed toward development of BWR parameters for the heavy hydrocarbons and modifications of the mathematical form of the BWR equation for application to complex hydrocarbon mixtures. The new equation-of-state approach presented differs considerably from previous methods in that phase equilibria rather than PVT data are used for determination of equation-of-state parameters. It is an explicit approach since the parameters are determined directly from mixture data. As such, it does not encounter problems inherent in the implicit method used by Benedict, Webb and Rubin 2-4 and numerous other investigators—one in which mixture parameters were postulated to be functions of the pure component parameters. The pure component BWR parameters, in turn, were determined from experimental PVT data. This method has been limited to mixtures containing components lighter than decane because of lack of vapor phase PVT data. Studies have been reported in which BWR parameters have been determined explicitly from PVT data for binary mixtures.6-8 However, since small concentrations of heavier components have only a minor effect on PVT behavior, it is doubtful that these explicit methods would yield useful results for condensate systems. Ellington and Eakin9 have shown that the accuracy of K-values predicted by an equation of state developed from mixture PVT data probably would be more than an order of magnitude lower than the accuracy of the PVT data. On the other hand, an equation of state utilizing parameters developed from phase equilibria data should predict K-values with accuracy comparable to the accuracy of the experimental phase compositions. This work applies this explicit approach with the objective of improving hydrocarbon mixture phase behavior predictions. Results are evaluated by comparing predicted and experimental K-values at reservoir, separator and gas plant

Jan 1, 1967

By Jos. Van Ackeren

Although the Siemens regenerator principle was introduced into byproduct coke-oven design about 40 years ago, many problems of construction, and particularly of heat distribution and pressure conditions, have not been fully solved. Heat should be applied to the walls of a coke oven in such a way that the coking of the charge of coal will be completed everywhere at the same time, and at approximately the same temperature. This means that the application of heat should be uniform from the top to the bottom of the coal mass (except for the thin layer at the top that is purposely kept at a somewhat lower temperature to reduce cracking of the byproducts); also that a little more heat must be applied to the coke end than to the pusher end, because the coal mass is a little thicker at that end. As a modern coke oven is about 40 ft. long and 12 ft. high, a real problem is involved in the proper application of heat to the oven walls so as to secure quick coking time (without endangering the walls through local overheating) and produce coke made at a uniform temperature. Design of Ovens In all regenerative ovens, the points of combustion are arranged in duplicate sets, one set operating in one-half the area of the heating wall and the other set alternately operating in the other half. Because of the reversal of the flow of gases, the points of maximum and minimum temperatures are alternately located at the same places, thus preventing dangerous local overheating. The practicability of the principle of reversal of flow seems to have been recognized at an early date, and has been applied with every conceivable flue arrangement, combustion chamber, and means of air and gas supply. To summarize the various principles that have proved useful for the control of oven-wall temperature, the best practice seems to have resulted from the acceptance of the use of vertical flues; the separate supply of air and gas to the base of these flues, with the resulting flame

Jan 1, 1923

By Jos. Van Ackeren

Although the Siemens regenerator principle was introduced into byproduct coke-oven design about 40 years ago, many problems of construction, and particularly of heat distribution and pressure conditions, have not been fully solved. Heat should be applied to the walls of a coke oven in such a way that the coking of the charge of coal will be completed everywhere at the same time, and at approximately the same temperature. This means that the application of heat should be uniform from the top to the bottom of the coal mass (except for the thin layer at the top that is purposely kept at a somewhat lower temperature to reduce cracking of the byproducts); also that a little more heat must be applied to the coke end than to the pusher end, because the coal mass is a little thicker at that end. As a modern coke oven is about 40 ft. long and 12 ft. high, a real problem is involved in the proper application of heat to the oven walls so as to secure quick coking time (without endangering the walls through local overheating) and produce coke made at a uniform temperature. Design of Ovens In all regenerative ovens, the points of combustion are arranged in duplicate sets, one set operating in one-half the area of the heating wall and the other set alternately operating in the other half. Because of the reversal of the flow of gases, the points of maximum and minimum temperatures are alternately located at the same places, thus preventing dangerous local overheating. The practicability of the principle of reversal of flow seems to have been recognized at an early date, and has been applied with every conceivable flue arrangement, combustion chamber, and means of air and gas supply. To summarize the various principles that have proved useful for the control of oven-wall temperature, the best practice seems to have resulted from the acceptance of the use of vertical flues; the separate supply of air and gas to the base of these flues, with the resulting flame

Jan 1, 1923

By Raymond D. Sloan

Dropping from third position among the oil-producing states of the nation in 1942, Oklahoma ranked fourth in 1943 with a total output of 121,431,ooo bbl., a decline of 11.9 per cent from the previous year's total of 137,792,000 bbl. Production ranged from a maximum of 346,900 bbl. daily in February to a low of 322,800 bbl. daily in October, and at the close of the year was averaging 330,000 bbl. daily from 52,096 wells, or an average of 6.3 bbl. per well. The state's well, average at the close of 1942 amounted to 6.7 bbl. At the turn of the year, it appeared reasonable to assume that Oklahoma's producing rate would continue its downward trend during 1944 unless reversed by greater than normal discoveries. To Jan. I, 1944, Oklahoma has produced 5,188,466,-ooo bbl. of crude oil. Development and Exploration A total of 1287 wells was drilled in 1943, representing an increase of 77 wells, or 6.4 per cent over the preceding year's total of 1210. Of the wells completed, 587 (45.6 per cent) were oil wells with an average initial production of 319 bbl.; 127 (9.9 per cent) were gas wells with an average initial of 8,639,000 cu. ft.; and 573 (44.5 per cent) were dry. A total of 333 wildcats was drilled (25.9 per cent of all wells), an increase of 13 (4.1 per cent) over the 1942 total of 320. Of the*wildcats drilled, 46 (13.8 per cent) were oil wells with an average initial production of 235 bbl.; 27 (8.1 per cent) were gas wells with an average initial of 8,249,-ooo cu. ft.; and 260 (78.1 per cent) were recorded as failures. Reconditioning of wells throughout the state led to a total recompletion of 230 wells. Of these, 131 were oil wells with a combined initial production of 8360 bbl., 31 were gas wells with a total initial of 211,950,000 cu. ft., and 68 were abandoned. The 46 successful wildcats opened 33 new producing areas, one of which produced from three separate horizons, and led to the development of production in new horizons in 11 old pools. While none of the 1943 discoveries have as yet developed into what might be termed major pools, the West Moore pool, in Cleveland County, and the West Edmond pool, in Oklahoma County, are the two outstanding new areas opened to production. The West Moore pool, sec. 29, 10 N., 3 W., discovered in December 1943, was completed for an initial production of 248 bbl. of oil in 3 hr. through small tubing chokes in the second Wilcox sand from 8787 to 8800 ft. One well was drilling in this area at the close of the year. The West Edmond pool, an April discovery in sec. 32, 14 N 4 W., is producing from the Hunton lime at a depth of approximately 6950 ft., the world's deepest Hunton lime pool. To the end of the year, 15 oil wells had been completed, with no gas wells and no failures. Accumulated production to Jan. I, 1944, amounted to 474,300 bbl. of 41" gravity oil. There were 29 active operations in the field at the end of the year. The West Edmond and West Moore pool discoveries established the first commercial production west of the Granite Ridge,

Jan 1, 1944

By Raymond D. Sloan

Dropping from third position among the oil-producing states of the nation in 1942, Oklahoma ranked fourth in 1943 with a total output of 121,431,ooo bbl., a decline of 11.9 per cent from the previous year's total of 137,792,000 bbl. Production ranged from a maximum of 346,900 bbl. daily in February to a low of 322,800 bbl. daily in October, and at the close of the year was averaging 330,000 bbl. daily from 52,096 wells, or an average of 6.3 bbl. per well. The state's well, average at the close of 1942 amounted to 6.7 bbl. At the turn of the year, it appeared reasonable to assume that Oklahoma's producing rate would continue its downward trend during 1944 unless reversed by greater than normal discoveries. To Jan. I, 1944, Oklahoma has produced 5,188,466,-ooo bbl. of crude oil. Development and Exploration A total of 1287 wells was drilled in 1943, representing an increase of 77 wells, or 6.4 per cent over the preceding year's total of 1210. Of the wells completed, 587 (45.6 per cent) were oil wells with an average initial production of 319 bbl.; 127 (9.9 per cent) were gas wells with an average initial of 8,639,000 cu. ft.; and 573 (44.5 per cent) were dry. A total of 333 wildcats was drilled (25.9 per cent of all wells), an increase of 13 (4.1 per cent) over the 1942 total of 320. Of the*wildcats drilled, 46 (13.8 per cent) were oil wells with an average initial production of 235 bbl.; 27 (8.1 per cent) were gas wells with an average initial of 8,249,-ooo cu. ft.; and 260 (78.1 per cent) were recorded as failures. Reconditioning of wells throughout the state led to a total recompletion of 230 wells. Of these, 131 were oil wells with a combined initial production of 8360 bbl., 31 were gas wells with a total initial of 211,950,000 cu. ft., and 68 were abandoned. The 46 successful wildcats opened 33 new producing areas, one of which produced from three separate horizons, and led to the development of production in new horizons in 11 old pools. While none of the 1943 discoveries have as yet developed into what might be termed major pools, the West Moore pool, in Cleveland County, and the West Edmond pool, in Oklahoma County, are the two outstanding new areas opened to production. The West Moore pool, sec. 29, 10 N., 3 W., discovered in December 1943, was completed for an initial production of 248 bbl. of oil in 3 hr. through small tubing chokes in the second Wilcox sand from 8787 to 8800 ft. One well was drilling in this area at the close of the year. The West Edmond pool, an April discovery in sec. 32, 14 N 4 W., is producing from the Hunton lime at a depth of approximately 6950 ft., the world's deepest Hunton lime pool. To the end of the year, 15 oil wells had been completed, with no gas wells and no failures. Accumulated production to Jan. I, 1944, amounted to 474,300 bbl. of 41" gravity oil. There were 29 active operations in the field at the end of the year. The West Edmond and West Moore pool discoveries established the first commercial production west of the Granite Ridge,

Jan 1, 1944

By Ernest Burchard

FLUORSPAR is found in most of the states from the Rocky Mountains westward, and commercial production of the mineral has been reported from Arizona, Colorado, Nevada, New Mexico, Utah and Washington. The map in Fig. 1 indicates the general distribution of many of these deposits but it is by no means complete. In the summer of 1926 the writer examined certain deposits of fluor-spar in Arizona, California, Colorado, New Mexico and Washington; in November, 1927, revisited the Jamestown, Colo., district, and in earlier years examined deposits in Colorado and New Mexico. Based on notes of his own and. on descriptions and other data by H. A. Aurand, H. W. Davis, R. B. Ladoo, V. C. Heikes, W. D. Johnston, Jr., and by producers of fluorspar, he prepared the following brief descriptions of deposits and estimates of reserves of fluorspar, originally for the use of the subcommittee on fluorspar of the Joint Committee on Foreign and Domestic Mining Policy and on Industrial Preparedness respectively of the Mining and Metallurgical Society of America and the American Institute of Mining and Metallurgical Engineers. Descriptions of many fluorspar deposits in various western states and districts have been published. It is not feasible to summarize this literature here, but the appended bibliography will indicate to the interested reader what papers are available.

Jan 1, 1933

By R. S. Hadi, L. Svarovsky

SUMMARY This is a report of a new development in on-line particle size measurement of fine powders in dust-laden gases. A continuous sample of the solids-air suspension is drawn from the process stream via a sampling probe by means of an air operated ejector into a cyclonic separator whereby the sample is subjected to a particle size dependent separation process and split into two streams, "overflow" and "underflow". The overflow stream carries most of the fines at a relatively low concentration and the underflow stream carries the coarse particles at a relatively higher concentration. The concentration of solids in the two streams is detected by electrostatic noise level technique which utilises the electrostatic charge accumulated on the solid particles due to their high velocity in the turbulent air stream, for the mass concentration measurement. The ratio of the solids concentration of the fines stream to that of the coarse stream is then correlated against the average particle size in the main process stream by a calibration curve. The in-plant tests clearly indicate that this relatively simple instrument offers good sensitivity in the size range from 2 to 6 µm, and is capable of giving a continuous indication of average particle size for process control purposes. Although the instrument was developed for a particular application, it may be used in other situations where fine powders are conveyed in gas streams. British and foreign patents are applied for.

Jan 1, 1980

By R. R. Webster, H. T. Clark

The side-blown converter has been investigated as a possible commercial process for the production of low nitrogen steel. During this work, two converters of 3-ton and 22-ton capacity were operated on a pilot plant basis for a total of 214 heats. The steel made in these converters was low in nitrogen and possessed good cold working properties. Some problems of converter operation remain to be solved. IN plants operating with a high iron capacity, sev-eral different refining methods are used in the conversion of the molten pig iron to steel. These include various ore practices in stationary and tilting open-hearths, the duplex process employing the Bessemer converter and open-hearth, and the Bessemer process. At J&L, a considerable part of the iron produced is handled by the Bessemer process, either alone or in conjunction with duplexing, and therefore an appreciable portion of the steelmaking research effort has centered about the method. This paper covers research work on the development of the side-blow converter for the commercial production of low nitrogen ingots and includes descriptions of the operation of a 3-ton and a 22-ton experimental converter at the Aliquippa Works. The refining of iron to produce steel requires the removal of a large portion of the carbon and silicon and the control of manganese, phosphorus and sulphur which are present in the iron in varying amounts. The first large-scale means of refining iron was the acid Bessemer process which was brought into use almost 100 yr ago. This method, using compressed air as the refining medium, accomplishes substantially complete removal of carbon, manganese and silicon. Phosphorus and sulphur are not affected but, by choice of an iron composition sufficiently low in these elements, a commercial product can be produced. Since the process will handle large tonnages rapidly, operates without external fuel and with a minimum of additional equipment, it quickly became the major tool in the early expansion of the steel industry. Later, the basic open-hearth process, by affording control of phosphorus and sulphur and by consuming the large quantities of steel scrap that were becoming available, forced the acid Bessemer process into a secondary position in the industry. During the past two decades the demand for steel to be used in cold forming and drawing operations has gradually increased. Bessemer steel, because of its work hardening and aging characteristics, is not as suitable for these applications as basic open-hearth steel, consequently the decline of the process was accelerated. More recently, because of changing economic conditions, this long range trend appears to have been arrested or perhaps reversed. Ingot production data for recent years furnishes only an incomplete picture of the importance of the converter in the American steel industry; open-hearth furnaces utilize large tonnages of blown metal for which no published statistics are available. Metallurgical Aspects The fundamental difference between Bessemer and open-hearth steels apparently lies not in the method of manufacture but, rather, in the differences in chemical composition of the two steels. It is further believed that the principal features distinguishing Bessemer from open-hearth steel are the higher nitrogen and phosphorus contents of the former. Evidence supporting this position is supplied by tests on laboratory induction furnace heats that were made to contain varying amounts of phosphorus and nitrogen but were otherwise similar to normal low carbon silicon-killed steels. Fig. 1, 2 and 3, summarizing the test results, are taken from G. H. Enzian's paper titled, "Some Effects of Phosphorus and Nitrogen on the Properties of Low Carbon Steels."' Fig. l indicates that phosphorus has a marked effect on the cold work embrittlement of steel as shown by the work brittleness test of Graham and Work.' In the low nitrogen steels, which as a group have the better cold working properties, the effect of phosphorus variations is the more pronounced.

Jan 1, 1951

By James E. Lawver, James L. Wright

This paper discusses the design and calibration of a Faraday pail for measuring electric charge. The paper also shows that at least for two minerals, quartz and calcite, the phenomenon that Johnson termed "reversibility" can be explained in terms of the contact electrification between the minerals and the metal rotor of an electrostatic machine. Each year the free world produces about 13 million tons of mineral concentrates by electrical separation. However, despite the rather general acceptance of electrical concentration as an industrial process, research in this area has lagged far behind the efforts devoted to competitive processes such as froth flotation. The purpose of this paper is to describe the design and calibration of a Faraday ice pail for measuring charge density on mineral grains and to show some of its applications in the area of electrostatic and electrodynamic research. THE DESIGN AND CALIBRATION OF FARADAY PAILS FOR ABSOLUTE CHARGE MEASUREMENT The electric charge on mineral grains at a given time during an electrical concentration process is de- pendent on many factors and cannot, in general, be accurately calculated a priori. It is thus important to devise a method of measuring absolute charge. One method of measuring electric charge is to note the potential rise of an electrometer when charged particles drop into a Faraday pail. Two types of Faraday pail have been constructed and calibrated. The first type, Faraday Pail I (Fig. 1), is a vertical pail originally designed to measure the charge due to contact electrification between mineral grains and a metal rotor or due to conductive induction when mineral grains are passed over a rotating cylinder in the presence of an electric field. The second type, labeled Faraday Pail II (Fig. 2), is a horizontal pail designed to determine the charge distribution of mineral grains after they pass through the separating zone of the electrical concentrator shown in Fig. 4. The main advantage of the horizontal pail is its low head-room requirement and the long opening which enables the experimenter to sample the entire width of the stream of minerals being separated. The Faraday pails were calibrated in the following manner: A calibration head was constructed in the form of a hollow brass sphere that could be held in an insulated metal cylinder by vacuum (Fig. 1). The capacitance of the sphere was calculated by measuring the capacitance of the sphere and cylinder combined and that of the cylinder alone and subtracting the latter measurement from the former. The sphere was then charged to a known potential (V) and allowed to drop into the Faraday pail which was attached to a Keithley Model 610A electrometer. This instrument has an accuracy of 2% full scale and has

Jan 1, 1969

By R. G. Ward, A. E. El-Mehairy

A technique was developed to calculate the density of liquid metals from the profile of a weighed levitated drop obtained by emitted light photography and calibration. The density of liquid copper was determined over the temperature range 1370" to 2100°K and expressed with the equation: The molar volumes and thermal coefficients of expansion are calculated. Copper, upon melting, was found to expand 3.34 pct. A knowledge of the density of liquid metals is essential as it is a parameter appearing in most theories of the liquid state. The liquid density is also necessary for the calculation of the commercially important contraction occurring on solidification. Unfortunately good density values are rarely available and the present work was undertaken to establish a new method of density determination free from the limitations of the existing methods. For liquid metals with high melting points, the variation and the limited number of density values reported in the literature have been caused primarily by difficulties in technique, a matter which has been adequately discussed by Urbain.' In all the methods used for measuring the density of the high-melting liquid metals there are sources of error, and corrections have to be made. For example, in the method of balanced columns, the formation of gas bubbles in one or both arms was a great source of error. In the pyknometer3 and immersed-sinker methods, corrections of certain volumes for thermal expansion to the operating temperature exceed 4 pct. In the maximum-bubble method5 a correction for the thermal expansion of the bubble-tube is used (about 1.6 pct); a second correction takes into account the change in the volume of liquid displaced by the bubble-tube (about 3.5 pct). Another method used is based on the shape of a drop of liquid, at rest on an inert refractory plaque, obtained photographically or radiographi-cally. The volume is calculated from the shape, which is sensitive to the surface tension and supporting material, by some intricate empirical relation. The drop contour changes with 90 deg rotation of the support.7 The application of all methods is limited by reaction between liquid metal and the apparatus. The successful stabilization of a mass of liquid metal during levitation melting8 afforded a technique for measuring the density of liquid metals out of contact with solid materials. The technique was developed by using copper as the density of liquid copper has already been studied extensively, thus allowing comparison with the new method. It consists of calculating the volume from the dimensioned profile of the levitated drop obtained by emitted-light photography and careful calibration. The molten egg-shaped drop spins around the magnetic axis of the coil (lined vertically) at a speed which seems to increase with increasing temperature. The method does not involve corrections and the experimental setup allows the use of vacuum or special atmospheres. The maximum operating temperature is limited by excessive evaporation of metal from the droplet. EXPERIMENTAL Levitating System. A stabilizing ring was used in conjunction with a 3-turn levitating coil energized by a 450-kc per sec, 10-kw Toccotron with a high current-low voltage output stabilized to f 1 pet.' APyrex glass tube with a Pyrex Optical flat window inserted through the coil and ring allowed the use of special atmospheres during levitation melting, as shown in Fig. 1. Optical System. Fig. 1 shows the optical arrangement used to photograph the profiles of the drop, parallel and perpendicular to the vertical spinning axis, simultaneously on the same frame of a high-speed 35-mm film. The optical system was adjusted to avoid any distortion of the profiles and to ensure that both profiles are in focus. The length of path from object to objective was about 30 cm, and a magnification factor close to 1 was obtained with the single-lens reflex-camera system. Temperature Measurement and Control. In operation, the specimen temperature was constant to 5 C for a fixed power input to the levitating coil and fixed rate of gas flow through the tube. The temperature was measured by an automatic two-color pyrometer (Coloratio) checked at the melting

Jan 1, 1963

By James J. Bean

F. M. Lewis—I believe that density recorders are a prerequisite to all well operated ore concentrators. Well designed density instruments are very accurate and give an excellent record of the steadiness of the operation. Controlling the density of a pulp with an instrument, as described by Mr. Bean, is new and the experiences in developing this controller at the American Cyanimid Co.'s Mineral Dressing Laboratory are very interesting and should be extremely helpful to others who are planning on designing or installing controlling density instruments. Instruments for recording the density of the classifier overflow or flotation feed are rather common in ore concentrators, but there are a number of profitable uses for these instruments that are not too well known. Density recorders with bubble tubes submerged to different depth in a classifier pool give an excellent record of the classifier operation. The loading and unloading of the machine, that is so easily masked in the density of the overflow, can be easily recorded if the instrument is installed at some depth in the classifier pool. On some occasions, two instruments with bubble tubes at different depths give a more candid picture of the irregularities in the classifier operation. When cleaner machines are operated in closed circuit with roughers, a record of the density of the cleaner tails will indicate the circulating load in the circuit and is very helpful in coordinating different operators, because quite often the circulating load will be increasing for some time before the analyses of the products will change. Density recorders are used to record the variations in the dilution of the underflow from thickening tanks and in at least one plant the instrument controls the underflow.

Jan 1, 1951

By James J. Bean

F. M. Lewis—I believe that density recorders are a prerequisite to all well operated ore concentrators. Well designed density instruments are very accurate and give an excellent record of the steadiness of the operation. Controlling the density of a pulp with an instrument, as described by Mr. Bean, is new and the experiences in developing this controller at the American Cyanimid Co.'s Mineral Dressing Laboratory are very interesting and should be extremely helpful to others who are planning on designing or installing controlling density instruments. Instruments for recording the density of the classifier overflow or flotation feed are rather common in ore concentrators, but there are a number of profitable uses for these instruments that are not too well known. Density recorders with bubble tubes submerged to different depth in a classifier pool give an excellent record of the classifier operation. The loading and unloading of the machine, that is so easily masked in the density of the overflow, can be easily recorded if the instrument is installed at some depth in the classifier pool. On some occasions, two instruments with bubble tubes at different depths give a more candid picture of the irregularities in the classifier operation. When cleaner machines are operated in closed circuit with roughers, a record of the density of the cleaner tails will indicate the circulating load in the circuit and is very helpful in coordinating different operators, because quite often the circulating load will be increasing for some time before the analyses of the products will change. Density recorders are used to record the variations in the dilution of the underflow from thickening tanks and in at least one plant the instrument controls the underflow.

Jan 1, 1951

By R. S. Shoemaker, D. L. Harris

Past investigations into the possibility of concentrating the low-grade iron ores of the Gogebic Range in Wisconsin have been hampered by the complex association of the constituent minerals. In part the problem arises from the fact that the iron occurs essentially as two minerals, hematite and goethite, having nearly the same chemical composition but exhibiting different physical properties. Individual grains of these minerals are usually so small that the ore must be ground to a size finer than 325 mesh if substantial liberation of the minerals is to be secured. Appraisal of beneficiation tests on this iron ore requires, therefore, some method of determining quantitatively the contents of constituent minerals in the various products of the beneficiation. Because of the chemical similarity of the two iron minerals, chemical analyses do not provide a means of differentiation. Although the minerals are different physically, they are both opaque and friable, and as the ore must be ground to a very fine size for liberation to be secured, quantitative microscopic methods of analysis are extremely difficult at best. In an effort to overcome these analytical problems, a quantitative X-ray diffraction analysis method has been developed at the University of Wisconsin for the research program on iron ore beneficiation.

Jan 5, 1955

By John C. Martin

The discovery of a new gas reservoir demands that the planning of a sottnd well-spacing program be initiated early in the development stage. It is the purpose of this discussion to illustrate by actual field examples the application of basic well-spacing principles, previously developed for oil reservoirs, to the problem of well spacing in natural gas fields. These studies are presented for the field use of geologists and engineers who are concerned with the initial planning of the proper development of the newly discovered gas reservoir. INTRODUCTION The phenomenal growth of a vigorous natural gas industry emphasizes the increasing importance of natural gas as a source of energy, fuel, and raw materials to our nation's economy. Since 1945 marketed production of natural gas for the U. S. has increased 21/2 times to a record high of 10.6 trillion cu ft during 1957. As major participants in the gas industry, we share an added interest to develop and produce our natural gas reserves with constantly improved efficiency. The subject of well spacing is vitally important to the gas industry, for the well itself plays a significant role in the development of the natural gas reservoir and in control of the recovery process. Maximum utilization of wells is an integral part of sound conservation practices. The discovery of a new gas reservoir demands that careful choice of well location and well spacing be made and that the planning of a sound well spacing program be initiated early an the development stage. With the drilling of the first development well, efforts of the geologist and engineer must be directed toward acquisition of adequate technical evidence upon which a firm recommendation for a spacing program may be based. With this technical appraisal as a foundation, operators and state regulatory agencies jointly can go far in providing a framework for sound development of gas fields to achieve a program of conservation that avoids the unnecessary well. WELL-SPACING CONCEPTS Through laboratory and field investigations of the mechanism of the recovery of oil and gas, of fluid behavior, and of effective control of reservoir and well, a crystallization of ideas regarding reservoir behavior has emerged as a well-developed technology. Associated with a better understanding of the fundamental principles underlying reservoir and well behavior has been the growth of concepts concerning the role of wells and their spacing in the development and operation of an oil or gas reservoir. In addition to serving as outlets for the withdrawal of fluids from the reservoir, wells are recognized as having two other important functions: (1) providing access to the reservoir to obtain information concerning the characteristics of the reservoir and its fluids, and (2) serving as a means by which the natural or induced recovery mechanism may be effectively controlled. Beyond a minimum number of wells required to fulfill these two functions, additional wells will not increase recovery. With particular emphasis upon well spacing in oil reservoirs, many studies of the well spacing-recovery relationship have evolved the concept that the ultimate oil recovery is essentially independent of the well spacing.' These fundamental concepts are no different when regarding the role of wells and their spacing in the natural gas reservoir. They are equally applicable to the consideration of well spacing in gas reservoirs. For the gas reservoir, the problem of well spacing then revolves around the question of drainage and the degree or extent to which a well may drain gas from its surrounding reservoir environment. Theoretical and Experimental Work During the past 30 years, theoretical and experimental work carried on to study the physical principles involved in the flow of fluids through porous media has shed light upon the matter of drainage. Fundamental mathematical equations have been derived to describe the mechanism of flow of oil and gas through porous rocks. With the recent advent of high-speed digital computers, attempts have been made with mounting success to develop solutions, employing numerical techniques, to mathematical expressions that describe more rigorously the physical behavior and mechanism involved in the unsteady-state flow of compressible fluids, such as a gas, through porous rock. In 1953, Bruce, Peace-man, Rachford and Ricez published a stable numerical procedure for solving the equation for production of gas at constant rate. The results of these calculations are significant with respect to this matter of drainage, for they indicated (1) that depletion of the gas reservoir resulted in a drop in pressure at the extremity of the

By Sam N. Dewitt, Albert S. Trube

This paper presents a discussion of the pressure maintenance operations which were begun in the New Hope Field. Franklin County. Texas. in 1944. The project has required the injection of extraneous waters at depths from 7.300 to 8.000 ft with intake well-head pressures up to 4.000 psi in three different reservoirs — the Bacon. Hill. and Pittsburg. Records of oil and water production. water injection and the GOR have been kept for each reservoir and reservoir pressures were taken at regular intervals. These data indicate that the Bacon Reservoir had no apparent water encroachment up to the time of water injection. However. the Pittsburg and Hill reservoirs had some natural water influx hut not sufficient to prevent pressures from declining below the bubble point. The Bacon and Hill reservoirs responded almost immediately to water injection. while the Pittsburg which is the least permeable. has shown good pressure response only since .August, 1948. The principle objective of the project has been to increase ultimate recovery. Success of the project to date also has resulted in reduced lifting costs. Esti- mates based on the initial water breakthrough patterns indicate that the primary objective of substantial additional recovery will he accomplished, and there is a possibility that the original estimates elf oil recovery with pres-sure maintenance will he exceeded. INTRODUCTION This pressure maintenance project was one of the earliest primary pressure maintenance programs to he attempted on a multiple zone field. There are three producing reservoirs into which water is being injected for the purpose of maintaining pressure and increasing the ultimate recovery- from each. This paper is limited in scope to al1 account of the development of the project. the pressure production relationship prior to the injection of water and the effect of water injection on the producing reservoirs. Also discussed are the nature of the injection system and the indicated results on initial water break-through in the Bacon Reservoir. FIELD CONDITIONS The New Hope Field, which is located about 12 miles northeast of Winusboro, Franklin County, Texas, is an elongated symmetrical anticline containing four known oil reservoirs. The reservoirs are of the Trinity group of the Comanchean or Lower Cretaceous period and are found in Table I. The oil productive portion of each reservoir is not present in all of the producing wells because their areas and positions vary with respect to one another. Fig. 1 shows the relative position of the four reservoirs and illusIrate? how some wells could penetrate all four, while others are restricted to three. two. or perhaps one. depending on structural location. The first three reservoirs contain undersaturated oil. The deepest. the Elledge, has a primary gas cap. Although this reservoir covers a considerable area of the field. it has a very thin section and a low order of permeability. Elledge producing wells have generally been characterized by an early increase in GOR, making it necessary to recomplete them in other reservoirs. (At present. one well is completed in the Elledge. which is still producing.) Because of the difficulties en-countered in producing oil from this reservoir. and the small quantity of oil actually present. future attempts at producing it will probably be on a salvage basis during the later life of the program. For this reason, the remainder of this report will be confined to a discussion of the Bacon, Hill and pius-burg reservoirs.

Jan 1, 1950

By Hiroshi Oikawa, A. G. Guy

Recent experimental evidence has shown that it is often incorrect to neglect the reactions occurring at an interface with respect to the diffusion reactions. By introducing reaction-rate constants and k for the transfer of components 1 and 2 between the a and b phases, a phenomenological description has been devised for the coupled processes of diffusion and in-terfacial reaction. An illustrative example has been analyzed with the aid of a suitable computer program. The results indicate that for kab values on the order of 10'1 cm per sec and Ð values of about 10¯10 sq cm per sec, the interfacial reactions are significant during the first 10 2 to l0 6 sec of a diffusion experiment. Among the observable effects of the interfacial reactions in this case appear to be the burying Kirkendall markers and an anomaly in the initial shifting of these markers. THE study of diffusion between two phases is especially important because of its direct connection to phase transformations. For example, the transformation of austenite to ferrite involves diffusion in the a and ý phases and also an interfacial reaction (trans formation) at the a/? interface. If ferrite and aus-tenite are the two members in a diffusion couple, the same two reactions occur during the diffusion process. The numerical values obtained for the diffusion coefficients and interfacial-reaction constants from diffusion experiments can then be employed to predict phase-transformation behavior. Refinement of the calculations of phase transformation is also suggested by the present method for treating two-phase diffusion. In the recent paper by Nolfi et al.' only the solute com ponent is considered in the interfacial reaction accompanying a phase transformation. The present analysis demonstrates that both components must be considered. It is generally recognized that reactions of some kind must occur at the interface in a two-phase diffusion couple, but usually it is assumed that the interface reaction occurs so rapidly that its effect on the overall process is unobservable because the slower diffusion process determines the kinetics of the process. However, Seith and Heumann 2 pointed out that effects of the interfacial reaction should always occur in the early stages of diffusion, and recently Eifert et al. 3 have shown that interfacial reactions influence the composition and motion of the interface in a/ß Al-Cu diffusion couples during the entire course of prolonged, high-temperature treatments. A general procedure for handling the combined processes of interfacial reaction and diffusion in a binary, two-phase system is to introduce kinetic coefficients for the interface reactions and to develop the system of equations governing the interlinked processes of diffusion and interface reaction. The resulting equations, although not amenable to solution in closed form, can be usefully manipulated by a digital computer. INTERFACIAL REACTIONS IN TWO-PHASE DIFFUSION Consider the general case of diffusion between two solid solutions, a and ß, which are adjacent phases in a binary system, Fig. 1. Two semiinfinite bars having compositions c1 and c0ß are jointed at x = 0. If concentrations are expressed in volume fraction,4

Jan 1, 1970

By Richard Moldenke

Note.—At the request of the American Society for Testing Materials, this paper wau presented at the New York Meeting, February, 1923, in connection with the "A. S. T. M. Tentative Specifications for Foundry Pig Iron" and The Physics of Cast Iron and Its Bearing on All Cast-iron Products and Specifications for Cast Iron," by William R. Webster. The discussion of this paper was not published by the Institute, having been referred to the American Society for Testing Materials, as these papers were again presented for discussion at the meeting of that Society at Atlantic Cit;, June, 1923. The result of these discussions is shown in the following abstract from the Committee A3 report on cast-iron specifications: During the past year, the adaptability of the tentative specifications for pig iron for the steel and the malleable foundry, in addition to the iron foundry proper, have been studied and suitable changes and rearrangements are being made which appear to cover the situation properly. In spite of the experience of foundrymen to the contrary, there is a persistent call from consumers of castinga for defixute compositions for given lines of castings. To respond to this call for information desired by the consumer—information every modern foundryman should have and guide his procedure with—the committee has requested the Sub-committee on General Cast!rigs to take up this matter with a view of constructing tables of analyses rang? for Important lines of foundry product. These analyses ranges however, are to be given as "recommendgd practice" and not intended for actual spkcification. In this way, the consumer of the foundry product will get the information he wants; the furnace-man will be gulded in the production of his pig irons to prepare for analyses ranges which are more closely standardized and have less of "freak" requirements made by Inexperienced metallurgists; and the foundryman will not be bound by chemical requirements he knows will not work out well with his particular reglonal supphes of melting stock. Doctor Moldenke's paper is published in full as it shows clearly the good results of the Institute's work in 1895 and a comparison of the same with the present knowledge of the metallurgy of cast iron—Bradley Stoughton, Chairman, Iron and Steel Committee. In MaRch, 1895, William R. Webster contributed a carefully prepared scheme for the study of the physics of cast iron to the American Institute of Mining Engineers at its Florida meeting. This summary of the interrelation of the chemical and physical characteristics of cast iron with the operations of daily foundry practice caused a wide discussion of the then little understood though universally used material. Mr. Webster has requested the author to bring the subject up to date and, while glad to comply, he must pay that with all the knowledge that has been gained in the quarter century that has passed since the subject was brought to the attention of the Institute—and we now are pretty familiar with cast iron in all its aspects—there is practically noth-

Jan 1, 1923

By Richard Moldenke

Note.—At the request of the American Society for Testing Materials, this paper wau presented at the New York Meeting, February, 1923, in connection with the "A. S. T. M. Tentative Specifications for Foundry Pig Iron" and The Physics of Cast Iron and Its Bearing on All Cast-iron Products and Specifications for Cast Iron," by William R. Webster. The discussion of this paper was not published by the Institute, having been referred to the American Society for Testing Materials, as these papers were again presented for discussion at the meeting of that Society at Atlantic Cit;, June, 1923. The result of these discussions is shown in the following abstract from the Committee A3 report on cast-iron specifications: During the past year, the adaptability of the tentative specifications for pig iron for the steel and the malleable foundry, in addition to the iron foundry proper, have been studied and suitable changes and rearrangements are being made which appear to cover the situation properly. In spite of the experience of foundrymen to the contrary, there is a persistent call from consumers of castinga for defixute compositions for given lines of castings. To respond to this call for information desired by the consumer—information every modern foundryman should have and guide his procedure with—the committee has requested the Sub-committee on General Cast!rigs to take up this matter with a view of constructing tables of analyses rang? for Important lines of foundry product. These analyses ranges however, are to be given as "recommendgd practice" and not intended for actual spkcification. In this way, the consumer of the foundry product will get the information he wants; the furnace-man will be gulded in the production of his pig irons to prepare for analyses ranges which are more closely standardized and have less of "freak" requirements made by Inexperienced metallurgists; and the foundryman will not be bound by chemical requirements he knows will not work out well with his particular reglonal supphes of melting stock. Doctor Moldenke's paper is published in full as it shows clearly the good results of the Institute's work in 1895 and a comparison of the same with the present knowledge of the metallurgy of cast iron—Bradley Stoughton, Chairman, Iron and Steel Committee. In MaRch, 1895, William R. Webster contributed a carefully prepared scheme for the study of the physics of cast iron to the American Institute of Mining Engineers at its Florida meeting. This summary of the interrelation of the chemical and physical characteristics of cast iron with the operations of daily foundry practice caused a wide discussion of the then little understood though universally used material. Mr. Webster has requested the author to bring the subject up to date and, while glad to comply, he must pay that with all the knowledge that has been gained in the quarter century that has passed since the subject was brought to the attention of the Institute—and we now are pretty familiar with cast iron in all its aspects—there is practically noth-

Jan 1, 1923

By W. P. Lass

The gold precipitate from the zinc-dust presses in the cyanide plant of the Alaska-Treadwell Gold Mining Co., Treadwell, Alaska, is treated, in the refinery adjoining, by the Tavener or lead-smelting method. About 3 or 4 tons of this precipitate is produced monthly having 'a gold assay value of $40,000 to $60,000 per ton. It was formerly the practice to treat the byproducts from this process, consisting of 2 tons of slag, 300 lb. of matte, 500 1b. of refinery refuse, flue dust, etc., in a 24-in. water-jacketed blast furnace. This practice was discontinued in the summer of 1914 by reason of the difficulty of keeping the lead-well open when treating a high-grade lead product; of preventing the loss of gold in the flue dust; and of avoiding injury to the general health of the refinery operators; a plain single-phase electric furnace was substituted for the blast furnace. The furnace was constructed from an old steel acid drum by cutting off the top and introducing a cable, made from strands of bare copper wire, through the bottom and spreading the strands out fan-shaped on the inside of the drum. Powdered graphite, obtained by grinding up old crucibles, mixed with 10 per cent. cement, was tamped wet into the bottom of the drum, around and completely covering the copper wires. The graphite was carried up to the bottom of the furnace, or lead-well, and acted as the lower electrode. The sides were built up of ordinary firebrick forming a melting chamber 14 in. in diameter by 20 in. high. The upper electrodes, of graphite or carbon, are 3 in. in diameter and 40 in. long, arranged with joints enabling new electrodes to be connected without shutting down or wasting stubs. A screw feed was arranged for raising and lowering the upper electrode. (Figs. 1 and 2.) The cover for the furnace had three openings, one for feeding the charge, one for the escape of gases, and one in the center for the introduction of the electrode. It was later found more practical to enlarge this center opening to 6 in. in diameter, to allow of a central feeding of the charge around the electrode.

Jan 1, 1916

By W. O. Crosby

INTRODUCTION. THE crystalline belt of the Atlantic Seaboard, south of New York, attains its maximum breadth of 220 miles on the northern border of North Carolina; and in this State it is most widely characterized by the occurrence of gold in workable deposits. Half a dozen auriferous belts have been recognized by Nitze and Hanna.1 These are, in the main, coincident in position and trend with the NE.-SW. zones of metamorphic slates and schists, which, more than any other feature, give character to the geological map of North Carolina. The central gold-belts, accompanying the main zone of slates and associated igneous rocks, are much the more important and persistent, and may be regarded as continuous northward across Virginia and southward into South Carolina. Tile eastern belt, on the other band, is the shortest and, economically, one of the least important. Its extreme length does not exceed 25 miles, the narrow band of slaty rocks to which it belongs passing, both NE. and SW., beneath the coastal-plain formations. But, although limited in area and production, this belt is, perhaps, comparable with the central belts or any part of the sea-board crystallines in the variety of conditions under which the gold occurs. It lies chiefly in the NE. part of Franklin county and the NW. part of Nash county, on the watershed of Fishing creek and other tributaries of Tar river. The elevation is between 400 and 500 ft. ; and the Tertiary peneplain has here an exceptionally perfect development, the reliefs separating the slightly incised stream-courses consisting of broad, flat-topped peneplain remnants, bounded by gentle lateral slopes.

Mar 1, 1908