Search Documents

By C. C. Harris

The 3-parameter equation* was introduced1 as having the necessary form and flexibility for describing the major features of size distribution curves. Also, Eq. 1 was shown to contain most of the widely used 2-parameter equations as special cases. Special methods are necessary in order to determine the parameters of 3-parameter equations by graphical means. The procedure given previously required double graphical interpolation followed by regraphing the interpolated data. The theoretical basis of the method was a difference equation eliminating y. Several other methods for obtaining the parameters have been under development and one method appears to overcome the disadvantages of the earlier method and satisfies several procedural requirements. The points in favor of the new method as compared to the earlier method are as follows: 1. Estimation of the quality of fit is direct, and is in fact an essential part of the procedure. 2. The data is plotted directly without the necessity of interpolation from a graph. 3. The method makes use of Rosin-Rammler2 paper which because of expanded scaling in the coarse sizes leads to improved accuracy1 as compared with the log-log plot for the Gates3-Gaudin4-Schubann5 representation. 4. There is a gain over the earlier method in overall accuracy and in simplicity.

Jan 1, 1970

By Edward A. Loria

A SERIES of papers on the study of austenite grain A size in cast steels has been published recently.'" These studies show that in the as-cast state, the austenite grains are quite large, for they form as the steel freezes at a very high temperature, but a simple reheating above the critical range produces a new set of austenite grains which, in many instances, is finer than ASTM grain sire No. 8. Furthermore, there is no apparent relationship between as-cast austenite grain size and subsequent grain size produced by heat treatment. The as-cast austenite grain size can be determined easily in plain carbon and low alloy steels which produce a continuous grain boundary f errite envelope in the as-cast structure. In the case of cast steels whose alloy content produces greater hardenability and suppresses the proeutectoid ferrite transforma-

Jan 1, 1952

By P. H. Dudley

THE piping and segregation of ingots of steel is a comprehensive subject, and must be studied in reference to the different grades of soft, medium, and hard steel, rather than to discuss it in a general manner, as though applicable to all grades. Rail steel, however, will receive the most consideration in this paper, for the wheel-loads of the motive pourer and rolling stock have doubled from 1890 to 1910. Steel rails and tires which were efficient under the light loads, became less serviceable under the double wheel-loads, quadrupled tonnage, and higher speeds. Bessemer Steel. Bessemer steel of froth 0.10 to 0.15 per cent. of carbon, for splice-bars, spikes, and tie-plates, rises in setting, and is cast in bottle-mouthed molds, which must be capped to prevent an over-flow from the top. This grade of steel rises in the molds and makes a longer ingot than the volume of molten steel when first teemed. The ingots which are allowed to cool and then cut open, show, particularly in the upper part, large occluded blow-holes, and when they are Dot oxidized or do not contain foreign matter, weld more or less completely when the steel is rolled or forged above 1,100° C., and it :is in this way that the blow-holes are closed it the low-carbon steels.

Jan 4, 1913

By I. H. Warren, E. Devuyst

A review of the physical and chemical aspects of the direct leaching of metal oxides has been given and com- pared to recent data of the authors and co-workers. The physical aspects, including the anisotropy of the dissolution, the hydration and the zero point of charge of some metal oxides are discussed first and then the kinetics of the dissolution of metal oxides are considered. A general mechanism of the leaching of oxides which describes most of the observed results is proposed.

Jan 1, 1973

By Raymond Wilson

Grinding costs are an important item in cement manufacture, and the cost of power is one of the large items in grinding costs. Even where power is of secondary importance, cost items dependent on mill capacity are influenced by the efficiency with which the mill uses power. Tube mills typify the grinding mills most generally used in cement plants, though other types are in use. Tube mills have been widely criticized as being extremely inefficient, and this feeling regarding them has led to many attempts to design more efficient grinding equipment. Other types may be an improvement over tube mills, but the improvement has certainly not been revolutionatry, at least as applied to clinker grinding. The very fact that there is doubt regarding the relative efficacy of various types of mills is an indication that an adequate basis for an analysis of performance is lacking. The development of methods of analyzing mill performance has been hampered by the lack of a suitable method for measuring the work actually done in pulverizing. There has been no acceptable standard to which mill performance might be compared. As a consequence, it was not known whether the margin of possible improvement in pulverizing operations was large or small. Even direct comparison of different types of mills was seldom possible because most plants had only one type of mill for each type of service. Comparisons between plants were difficult because of differences in the grinding characteristics of various clinkers. Some recent developments complete a chain of circumstances that place the cement industry in a particularly fortunate position for the study of its clinker-pulverizing operations. Modern investigators of grinding phenomena have generally agreed that the best measure of mill performance is the production of new surface. For most materials this measure of performance is largely theoretical and has a rather remote connection with the practical aims of the grinding operation. In clinker grinding, on the other hand, surface area is intimately connected with the properties conferred on the cement by grinding. Morcover, the determination of surface area is rapidly coming into routine use as a tost

Jan 1, 1938

By Raymond Wilson

Grinding costs are an important item in cement manufacture, and the cost of power is one of the large items in grinding costs. Even where power is of secondary importance, cost items dependent on mill capacity are influenced by the efficiency with which the mill uses power. Tube mills typify the grinding mills most generally used in cement plants, though other types are in use. Tube mills have been widely criticized as being extremely inefficient, and this feeling regarding them has led to many attempts to design more efficient grinding equipment. Other types may be an improvement over tube mills, but the improvement has certainly not been revolutionatry, at least as applied to clinker grinding. The very fact that there is doubt regarding the relative efficacy of various types of mills is an indication that an adequate basis for an analysis of performance is lacking. The development of methods of analyzing mill performance has been hampered by the lack of a suitable method for measuring the work actually done in pulverizing. There has been no acceptable standard to which mill performance might be compared. As a consequence, it was not known whether the margin of possible improvement in pulverizing operations was large or small. Even direct comparison of different types of mills was seldom possible because most plants had only one type of mill for each type of service. Comparisons between plants were difficult because of differences in the grinding characteristics of various clinkers. Some recent developments complete a chain of circumstances that place the cement industry in a particularly fortunate position for the study of its clinker-pulverizing operations. Modern investigators of grinding phenomena have generally agreed that the best measure of mill performance is the production of new surface. For most materials this measure of performance is largely theoretical and has a rather remote connection with the practical aims of the grinding operation. In clinker grinding, on the other hand, surface area is intimately connected with the properties conferred on the cement by grinding. Morcover, the determination of surface area is rapidly coming into routine use as a tost

Jan 1, 1938

By H. D. Kessler, Joseph B. McAndrew

WHEN there is occasion to make structural use of metals at temperatures above 900°C (1652°F), the choice of alloys is severely limited, and those materials which meet special requirements as to density, strength, toughness, and resistance to creep, oxidation, or fatigue at such temperatures are at a premium. Any new type of high temperature alloy which is found to be outstanding with respect to several of these properties is therefore likely to find special applications for which it is uniquely advantageous as compared to other alloys. Such is the case with the 7 titanium-aluminum alloys. This y phase is an intermediate phase based on the composition TiAl, and extends from about 35.5 to 44.5 wt pct Al at temperatures up to 1000°C, above which the field broadens to include 60 pct A1 at 1340°C.' The alloys of principal interest have a narrow melting range, with 7 forming by the peri-tectic reaction, melt + ß=y at about 1460°C. Unlike most intermediate phases, the binary alloys containing titanium and aluminum in approximately equiatomic proportion possess low room temperature hardness,' in addition to which they have low density, good resistance to oxidation, and relatively high modulus of elasticity.' Unpublished work done at Armour Research Foundation showed

Jan 1, 1957

By R. W. Guard

ALTHOUGH etching techniques have been developed for revealing dislocation sites in several metals and ionic crystals,h t is valuable to extend the technique to new metals. An etch pit method for nickel has been developed on the basis some suggestions of Dr. John R. Cuthill of the National Bureau of Standards who had observed etch pits in creep specimens of nickel. The etchant used was proposed first by wensch2 for revealing grain size in nickel. The present paper describes the evidence that the technique can be used to reveal dislocations and gives the conditions under which etching can be carried out. The specimens examined were vacuum melted high-purity Ni (99.985 pct Ni) and commercial "A" nickel (99.8 pct Ni). Both materials contained greater than 0.008 pet C and had been annealed in nitrogen or dry hydrogen at 1100o to 1200°C. This gave a grain size of 1.5 mm in the high-purity nickel and 0.050 mm in "A" nickel. Tensile specimens (0.254 in. diam) were deformed from 0.25 to 10 pct at room temperature and then heated for 1/2 hr at different temperatures from 400" to 900°C. The specimens were sectioned longitudinally then polished electrolytically in 60 pct H2SO4 and etched in 35 pct H3PO4 solution at 0.2 to 0.4 v for 30 sec to 3 min. The best method for setting the proper voltage for etching is to increase the voltage until gas bubbles are evolved vigorously from the specimen and then cut it back by 10 pct. It is necessary to heat the specimen above 500°C after deformation in order that etch pits will be formed. This "decoration" treatment permits carbon to segregate to the dislocation rendering them sensitive to etching. It was demonstrated that carbon was the decorating impurity by decarburizing some specimens in wet H2 at 1200°C. The susceptibility to etch pitting was lost following this treatment but could be restored by carburizing in contact with graphite. Some rearrangement of the dislocations in the as-deformed structure occurs on heating at 500oC and above so that the technique can not be used to study the nature of dislocation patterns in deformed specimens. Extended etching does not change the number of pits although the background becomes rough and the pits quite large. The polycrystalline specimens with various strains were examined after annealing at different temperatures. Typical patterns are shown in Figs. 1 and 2. In the unstrained specimen, Fig. 1, the density of pits is 2.5 X 10' per sq cm. All grains show pits regardless of their orientation although there is a

Jan 1, 1961

By B. E. Hoffacker, R. E. Lund, J. Ferrighetto, G. E. Welch

Since October 1965 the Josephtown Smelter of St. Joseph Lead Co. has commercially applied the Heavy Media Separation process to reclaim zinc and reject gangue from electrothermic zinc furnace residues. In addition, heavy medium is produced from the ferrosilicon which is present in the furnace residues. By way of background, the Josephtown Smelter produces zinc metal and zinc oxide by the electro- thermic process. The principal feed to the vertical shaft electric furnaces is sized sinter and coke. Temperature of the charge in the furnaces varies from roughly 900°C near the wall to 1300-1400°C in the central regions. Zinc smelting is rapid and nearly complete in the main body of the charge, but little zinc is smelted near the wall. In addition to fusing high gangue content particles, the high temperatures promote side reactions, the most important of which is reduction of iron oxide and silica to form a low grade ferrosilicon containing about 82 % Fe and 13% Si.

Jan 12, 1968

By E. H. Rennhack

When cast hypoeutectic Zn-Ti alloys are rolled, the TiZn15 compound particles arising from eutectic decomposition form a network of fibers promoting improved creep resistance.' The effect is magnified with increasing titanium content and extends to hy-pereutectic concentrations. Strip produced from the latter-type alloys, however, also contains large, primary crystals of the compound that tend to initiate cracking during subsequent fabrication operations. In a study of the influence of various casting modifications on the size and distribution of these crystals, the phase relationships existing between the eutectic and the TiZnIs intermetallic compound in the Zn-Ti system were of major interest. Although several in- vestigators1 4 have explored the equilibria within this compositional range, their results show considerable lack of agreement. Consequently, with the exception of the solvus boundary, the constitution of this system containing up to approximately 1.0 wt pct Ti was . The findings are reported in the present note.

Jan 1, 1967

By Sidney W. Poole

THE control of deoxidation, together with other factors involved in electric-furnace melting practice, to consistently produce heats of high-quality alloy steel to stringent specifications as to nonmetallic inclusion content is a problem of considerable magnitude. Steel melting as an industrial process is subject to many variables that can influence the quality of the product made. In order to modify the size, amount and distribution of inclusions and to promote their elimination, deoxidation, among other practices, plays a major part. The primary purpose of deoxidation in the production of electric-furnace alloy steels is the removal of dissolved oxygen present as FeO in the bath, which is produced as a result of prior oxidizing conditions. The elements usually added to effect this removal of soluble oxygen are those that will, upon addition, cause the formation of an oxide compound insoluble in the molten steel bath as silica, alumina or silicate combinations.

Jan 1, 1947

By M. B. Kahle, A. D. Pernichele

Four types of slope failures in waste dumps are recognized debris flow, foundation failure, edge slump, and blowout. The first three types, although at times causing considerable damage to property and interfering with mine operations, are not usually dangerous to personnel because of their slow rate of movement. The fourth type, the blowout, is the most dangerous because of its explosive mode of failure and lack of forewarning. The December 1969 failure at Verona dump is presented as an example of a blowout. Data from piezometer holes indicate that the blowout was due to perched leach solutions near the face of the dump. The level of water in this zone is very closely related to the rate of leach water application on the dump. A detailed analysis of core samples indicates that the impounded water was perched on a zonal accumulation of jarosite which is associated with a buried dump surface. Drain holes proved successful in controlling perched leach solutions in the critical zone near the face of the dump. Monitoring of the water level in the perched zone is considered essential in preventing blowouts. The use of drain and piezometer holes has allowed an increase in the rate of water application on the dump while preventing additional failure.

Jan 1, 1972

By A.A. Gustafson

In diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport's operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1940. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Free-port Sulphur Co. discharges over the entire circumference, which gives a discharge ltp of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole, The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

By A. A. Gustafson

In diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport's operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1940. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Free-port Sulphur Co. discharges over the entire circumference, which gives a discharge ltp of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole, The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

By B. E. Thompson, H. B. Fuqua

The area discussed herein, commonly known as the North Texas district, embraces the following 10 counties: Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita and Wilbarger. It is underlain by two major structural features. The northernmost portion of the district, including Coolie, Montague, northern Clay, Wichita, Wilbarger, Foard and Hardeman Counties, is underlain by the system of buried mountains known as the Red River uplift, which is parallel to and closely related to the Wichita-Amarillo uplift of Oklahoma and the Texas Panhandle. While the presence of a great majority of the numerous oil fields of the area is traceable to this feature, the production in Archer, southwestern Clay and southeastern Baylor Counties is due to the influence of what is known as the Cisco arch (so called because of its influence on Cisco deposition), the axis of which extends in a northwest-southeast direction across southwestern Wichita County into Archer County. Developments during 1938 Important discoveries in the district were considerably more numerous and of more economic importance than for several years. In addition to a number of small, relatively unimportant discoveries and to the usual local extensions to the various producing fields in the several counties, at least eight fields, most of them apparently of considerable areal extent and importance, were found. The Helmerich and Payne, Incorporated and Blackwell Oil and Gas Company No. 1 Wilson. 4 miles southeast of the town of Holliday, in north central Archer County, encountered a pay of Strawn age at a depth of 3841 to 3858 ft., and was completed for an initial production of 1952 bbl. T'his well opened a new deep pool in the K. M. A. producing zone 8 miles southeast of the K. M. A. production. Subsequently an additional deeper horizon, also of lowcr Strawn age, was discovered by wells that failed to yield commerecial oil from the horizon of the discovery well.

Jan 1, 1939

By H. B. Fuqua, B. E. Thompson

The area discussed herein, commonly known as the North Texas district, embraces the following 10 counties: Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita and Wilbarger. It is underlain by two major structural features. The northernmost portion of the district, including Coolie, Montague, northern Clay, Wichita, Wilbarger, Foard and Hardeman Counties, is underlain by the system of buried mountains known as the Red River uplift, which is parallel to and closely related to the Wichita-Amarillo uplift of Oklahoma and the Texas Panhandle. While the presence of a great majority of the numerous oil fields of the area is traceable to this feature, the production in Archer, southwestern Clay and southeastern Baylor Counties is due to the influence of what is known as the Cisco arch (so called because of its influence on Cisco deposition), the axis of which extends in a northwest-southeast direction across southwestern Wichita County into Archer County. Developments during 1938 Important discoveries in the district were considerably more numerous and of more economic importance than for several years. In addition to a number of small, relatively unimportant discoveries and to the usual local extensions to the various producing fields in the several counties, at least eight fields, most of them apparently of considerable areal extent and importance, were found. The Helmerich and Payne, Incorporated and Blackwell Oil and Gas Company No. 1 Wilson. 4 miles southeast of the town of Holliday, in north central Archer County, encountered a pay of Strawn age at a depth of 3841 to 3858 ft., and was completed for an initial production of 1952 bbl. T'his well opened a new deep pool in the K. M. A. producing zone 8 miles southeast of the K. M. A. production. Subsequently an additional deeper horizon, also of lowcr Strawn age, was discovered by wells that failed to yield commerecial oil from the horizon of the discovery well.

Jan 1, 1939

By F. E. Griffith

Several disastrous and a great number of near-disastrous mine fires have been started by igniting the combustible conductor insulation and outer covering of trailing cables. Those who have had experience in fighting such fires know that they are extremely difficult to combat and extinguish owing to the irritating and noxious gases, fumes and vapors evolved from evaporation, distillation and combustion of the sundry compounds used in the construction of cables. When electric-motor-driven coal-cutting machines were first introduced in coal mines, the electricity was transmitted to the apparatus by two single-conductor trailing cables. Later, two-conductor parallel and concentric types were developed. These early cables were made with the materials available at that time with relatively little thought given to using new materials or utilizing the old to the best advantage. The copper conductors were stranded to give flexibility, but there were too few strands and the method of laying them was such that they did not endure well the stresses of twisting and pulling, to which trailing cables used in mines are usually subjected. The rubber insulating compounds used were not satisfactory in resisting water, high temperature, and the crushing stresses encountered in mine service. The outer coverings were cotton or jute braids saturated with tars or asphalts having relatively no abrasive resistance. In fact, the only consideration given to trailing cable design because of its extremely short life, was to construct it at the lowest possible cost. With increased electrification and mechanization, more serious problems were encountered. Cables used in mines were exposed to more severe conditions than in any other industry. The excessive overload currents, poor heat dissipation, severe abrasion, crushing loads from falling material, runovers, and any of the other things that tend to destroy cable, called for vast improvement in trailing cable design for mine use. About 1918, one manufacturer who recognized the need for improving the toughness of cables in order to obtain greater safety and longer life, developed a special rope-stranded conductor, a superior rubber insulation compound and a tough rubber sheath or jacket compound. As a result of this type of construction, broken conductor strands were practically eliminated, the insulating material withstood high temperature without undue disintegration, and the jacket, similar to that used for automobile tire tread, had high abrasion resistance, high tear resistance, and was waterproof. While the initial cost of these cables was higher than the jute-filled braided types, this disadvantage was more than offset by increased safety and longer service. Cables with these improved characteristics were first installed in mines in 1920. Since 1930, the use of braided trailing cables in coal mines has been almost completely supplanted by the more superior types, employing high-grade rubber compounds for insulation and sheath. The next steps taken to improve the

Jan 1, 1949

By Michael Perch, Charles C. Russell

Nearly 75 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69.9, and in 1938 it was 61.3. To produce a net ton of pig iron 1757 lb. of coke was required in 1940 and 1760 lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank1 standardized by the American Society for Testing Materials. Although this method of classification has been an American standard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1942

By A. C. Emery

The physical and chemical properties for the metalliferrous feed materials to the Imperial Smelting Process blast furnace are defined and the means of achieving these properties by the sintering or briquetting routes discussed. Modern sinter plant performance data is included with a plant flow sheet showing draughting patterns. The necessity for ensuring an adequate SO2 content in sinter machine gases when roasting sulphide materials to enable conversion to sulphuric acid in a contact acid plant is described. The ability of the process to consume limited quantities of oxide materials, residues from other processes and other secondary sources is discussed. The argument for a briquetting route is developed out of this limitation and the merits of cold and hot briquetting examined. Development work on the hot briquetting route for this purpose is briefly described and several flow sheets outlining possible applications for hot briquetting to different raw material situations including the preparation of low lead charges for the furnace are presented.

Jan 1, 1977

By Francis F. Lucas

Jan 1, 1931