Search Documents

By Andrew Mayer

Early in 1942 National Lead Co. was requested by the War Production Board to construct and operate a plant for the Government to produce magnesium by the ferrosilicon process which had been developed by Dr. E. M. Pidgeon in the laboratories of the Canadian National Research Council. A contract with the Defense PlantCorporation was concluded in May 1942 and Magnesium Reduction Co., a wholly owned subsidiary of National Lead Co., was formed to carry out this project. The capacity of the plant was rated at I0,000,000 lb. of magnesium per year, equivalent to an average production of about 14 tons per day. The Process The process, in brief, is as follows: The raw materials are dolomite and ferro-silicon, 75 per cent grade. The dolomite is calcined, the calcine and ferrosilicon are ground and mixed and the mixture is briquetted. The briquets are charged into tubular retorts of chrome-nickel steel set horizontally in a furnace with the open ends projecting outside the front wall. The retorts are then closed and evacuated. Magnesium is liberated according to then reaction 2(MgOl CaO) + Si = 2Mg + zCaO, Si% It is distilled from the charge and con- densed on a removable sleeve in the throat of the retort. Sodium and potassium, if present, are also liberated, distilled and condensed on a "sodium condenser" in the end of the retort. At the expiration of the distillation period the retorts are discharged and the cycle of operations is repeated. For the rated daily capacity of 14 tons of magnesium there are required approximately 170 tons of dolomite, equivalent to about 85 tons of calcine, and 16.5 tons of ferrosilicon. The retort residue, a bulky powder which at present is waste, amounts to about 87 tons. Choosing the Site The investigation to select the location of the plant was conducted by the Research Laboratories of National Lead Co. This work included geologic and economic surveys of a number of districts, examination of dolomite samples by chemical, spectrographic and petrographic methods and large-scale tests of dolomite from several of the more promising localities. in the last-named tests 2-ton samples were put through the ferrosilicon process in the pilot plant of the Canadian National Research Council, under the guidance of Dr. Pidgeon. The conclusions drawn from the investigation, in regard to the quality of dolomite to be used in the ferrosilicon process, were: First, the dolomite should contain not less than 21 per cent MgO and not more than 2 per cent acid-insoluble material. Second, the dolomite should

Jan 1, 1944

By R. H. King

This paper describes the results of an underground coal mine trial installation of a shielded trailing cable. The cable was a three conductor, round, type SHC-GC and was installed on a shuttle car in a conventional room-and-pillar mining section. The purpose of the study was to evaluate proposed legislation that would require shielding on low-voltage trailing cables. Such legislation would require machine modifications to cable reels, packing glands, and couplers; increase cable splicing complexity; and necessitate additional splicing materials and training. Furthermore, fault location might be more difficult. Even though shielding will cause some problems for the mine operator, it can reduce electrical shock hazard to mine workers. This paper presents information that mine operators can use to solve most of the problems encountered if they are required to install shielded cables. The in-mine evaluation was funded by the US Bureau of Mines; however, the views and conclusions in this paper are those of the author and should not be interpreted as necessarily representing official policies of the US government.

Jan 1, 1982

By S. P. Goplen, M. Henriksen, T. F. Barron

In the past decade, numerous large scale drilling projects have made use of reverse circulation air lift methods. Reverse air lift pumping can be established by injecting gas into a column of liquid; the subsequently decreased density of the gas-liquid mixture allows atmospheric pressure outside the lift conduit to establish flow. The rate of flow can be controlled by varying the gas to liquid ratio. A typical reverse circulation air lift system is depicted in [Fig. 1]. Allen 1 has described a number of reverse air lift drilling projects. Although cited examples are generally related to large diameter holes, the method has seen use in other applications such as sand dredging, chemical pumping, water well pumping. and continuous coring. One particular benefit obtained with enclosed reverse circulation drilling is elimination of lost circulation. The required air/water ratio for pumping at a given submergence and lift has been established experimentally by Gibbs.2 His data, however, do not reflect sensitivity of flow rate to air/water ratio. Further, in Gibbs' work, air apparently is injec-

Jan 1, 1980

By R. G. Mallon, R. L. Braun

Primary copper-sulfide ore deposits that are well below the water table can be chemically mined by in-situ high-pressure leaching. The leaching is accomplished by pumping oxygen gas into the bottom of a large underground flooded column of rubblized ore. Part of the injected oxygen dissolves under the high hydrostatic pressure in the column. With a high enough injection rate, the excess oxygen gas induces a convective circulation of oxygenated solution within the rubble column, which transports dissolved oxygen throughout the system. At elevated temperatures, this results in a relatively rapid dissolution of the copper minerals. A method of calculating the leaching rates is presented. The calculation is done by means of a finite-difference computer code that couples all of the processes relating to copper leaching, convective circulation, and the injection, dissolution, and consumption of oxygen. Results of the calculation for a typical case show that over 70% of the copper can be extracted in less than six years with good efficiency in oxygen utilization.

Jan 1, 1976

By J. M. Snook, F. C. Langenberg

FOR a better understanding of the melting and refining processes, the oxygen content of the steel bath should be determined. The oxygen content influences many process and product variables such as the efficiency of alloy recoveries, the ingot structure (through reaction with carbon in the steel), certain reaction rates, cleanliness (formation of indigenous oxide inclusions), and mechanical properties. Many methods of sampling liquid steel for oxygen have been devised. These methods can be divided into two main groups: 1) taking samples directly in the furnace or ladle;'-'0 2) removing the metal from the furnace or ladle in a sampling spoon and pouring it into a mold, or drawing the metal from the spoon into a sample holder.11-l4 The advantages and disadvantages of the two general sampling methods are presented in Table I. The bomb-sampling technique described by Huff, Bailey, and Richards8 has been used by the Crucible Steel Co. in certain research projects where oxygen contents were needed. It was recognized that a localized boiling condition could result when the mold is introduced into the steel bath, although the work of Gilbert and Bailey9 seems to indicate that the carbon boil occurring in the bomb-sampler cavity has a negligible effect on the oxygen content. In order to confirm the reported negligible effect of a carbon boil, additional work was done with adaptations of the conventional bomb sampler. The methods used are shown in Fig. 1 and are as follows: 1) Type A: aluminum wire (0.125-in. diam) coil in cavity; steel cap over mouth 2) Type B: aluminum cup in cavity; aluminum cap over mouth, 3) Type C: aluminum cup in cavity; steel cap over mouth, 4) Type D: fine aluminum wire (0.013-in. diam) in cavity; steel cap over mouth. The amount of aluminum wire in the Type A and D samples varied from 0.8 to 1.2 pct of the sample weight. The aluminum cups averaged 2.0 pct of the sample weight; the latter were used to ensure that the steel contacting the walls of the bomb cavity was fully killed. Samples were taken from plain carbon heats made in open-hearth furnaces. This grade of steel before silicon additions is essentially an Fe-C alloy and the effects of other alloying elements on the oxygen activity can be neglected. The results of sampling with the bomb samplers is shown in Fig. 2 where the percent oxygen is plotted against the percent carbon on log-log paper. Spoon sample results on the same grade of steel where the sample was killed in the spoon are shown in Fig. 3. The oxygen contents were determined by the vacuum fusion method. A comparison of Figs. 2 and 3 shows that the oxygen concentrations obtained with the spoon-sampling method (metal killed in the spoon after slag removed

Jan 1, 1960

By Donald R. Mason, Daniel F. O’Kane

DIFFERENTIAL thermal analysis measurements have been used to determine the ZnTe-In2Te3 pseudo-binary phase diagram. Since ZnTe and In2Te3 are both semiconductors, any intermediate compounds formed in this system should also be semiconductors according to the rules delineated by Mooser and pearson.1 The compound ZnIn2Te4 was first reported by Hahn et a1.2 and it has subsequently been prepared and characterized electrically by several workers. A brief summary of this work has been presented by Mason and O'Kane3 who also report that the compound appeared to melt peritec-tically. The Zn-Te phase diagram has been investigated by Kulwicki4 who found that ZnTe has a melting point of 1290° + 2°C. The In-Te diagram published in Hansen' contains significant errors, and has been redetermined by Grochowski et al.6 However, both sources agree that the melting point of In2Te3 is 667°C, with the latter authors reporting the previously observed solid-solid transformation occurring at about 550°C. Hahn ef al.2 reported lattice-parameter values for the ZnTe-In2Te3 system. The 67 mole pct ZnTe-33 mole pct In2Te3 composition was the only

Jan 1, 1965

By Leon Y. Sadler, E. K. Landis

Froth flotation has been described by several authors" as being analogous to a first-order rate process. Although a few investigators"," have found orders other than one fit their data best, the rate is described most often by the first-order equation, [ ] where r is rate of disappearance of floatable mineral by flotation, C(t) is concentration of floatable mineral in the cell, t is time, and k is first-order flotation rate constant. One of the difficulties in using this rate equation to develop a mathematical description of an actual flotation process is the determination of a suitable value of the constant k. The value of k, which reflects the floatability of the floatable mineral, is dependent on the hydrodynamic conditions in the cell, type and concentration of flotation reagents used, pulp density, and pH, method of froth removal, aeration rate, particle characteristics, and many other factors. Therefore, it is reasonable to expect that each particle of floatable material has a distinct value of k and that a unique distribution of k values exists for given feed and cell conditions. This has been observed and discussed by several investigators, and mathematical descriptions of the batch cell and steady-state continuous cell with distributed flotation rate constant have been developed." The mathematical description in the form of a transfer function of the continuous or flow cell under unsteady-state conditions with a distributed flotation rate constant has not been presented in the literature. The purpose of this note is to make such a presentation. The basic features of the perfectly mixed continuous

Jan 1, 1974

ROBERT M. KEENEY,* Portsmouth, Ohio (written discussion?).- Mr. Coffin has written a most interesting paper that covers most of the uses to which water-cooled devices are subjected; but to meet with the operating department's approval, these devices must effect a saving in cost per ton of ingots produced in the furnace. The making of steel in the open-hearth furnace is dependent entirely on the personal element. It is not possible to charge the furnace with so much raw material, turn on a valve for heat, and by use of recording thermometers, clocks, etc. empty the furnace when a steel is made. Competent men trained to the work must be in charge all the time, and the quality and quantity of steel produced is quite as dependent on the care and working qualities of the furnaces as on the raw material and working of the charge itself. Steel making is hot, hard work and the inducement offered to technical men to take up this work is not sufficient to induce many to enter the field. The result is that most of the workmen in an open-hearth plant, the men who actually operate the furnace and make the steel, are not technical men and do not understand the "whys" and "wherefores " and care less. All this means that a furnace must be built as nearly fool-proof as possible. By this I mean that it is necessary to protect those parts of a furnace most subject to abuse by water-cooled devices whenever possible, and these water-cooled appliances must he as nearly fool-proof as they can be made. The control of the gas entering a furnace is of the utmost importance. This means a properly designed port must have the same design throughout the whole run of the furnace. This is not possible with the ordinary

Jan 6, 1919

By E. P: Mathewson

Discussion of the paper of E. P: Mathewson, presented at the Butte Meeting, August, 1913, and printed in Bulletin No. 78, June, 1913, pp. 1033 to 1037. PROF. JOSEPH W. RICHARDS, South Bethlehem, Pa. :-Speaking to the question of the development of the basic lining, and speaking from a somewhat considerable study of the history of the process, ,I think Mr. Mathewson's conclusion (in the last paragraph. of his paper) is perfectly justified and is very fairly stated. Messrs. Smith and Pierce worked at developing their process for many years ; copper men had been trying their level best to get away from the silica lining of the converters and had uniformly failed. On one page of Mr. Mathewson's paper we read that at the old works of the Anaconda Company, at Anaconda, the experiments " were abandoned on the score of cost and lack of advantages." On the next page, after describing the work of Messrs. Smith and Pierce, we have the statement that the Anaconda Company lined a shell with mangnesite brick and the ?results were excellent." I think Mr. Mathewson's statement that to Smith and Pierce belongs the credit of developing a long-discredited idea, is correct. C. D,. DEMOND, Anaconda, Mont. :-It seems to me that the matter of the lining is important; my impression is that they used tar in their basic lining and that did not seem to be at all successful at Anaconda, but silicate of soda was very successful. MR. RICHARDS :-I did not know that they- had abandoned the use of tar. MR. DEMOND :-I said I thought that was the practice. At Anaconda that was not at all satisfactory in the basic linings. Silicate of soda was very satisfactory and is so.

Jan 11, 1913

By S. D. Thompson

An AIME transaction by P.L. Allsman (1960), "Analysis of Explosive Action in Breaking Rock," contains many useful concepts applicable to blast design. Of special interest was the derivation of a heave blasting burden formula, which is important in establishing the maximum burden. Unfortunately, its derivation contains a fundamental error and then a compensating one. This formula was: [bImpulse _P d At max =nwuwu where: bmax = maximum burden in m (ft). P= average detonation pressure in N/m2 (lb per ft2). A= duration of the average detonation pressure in sec. n= 3.1416. w= specific weight of rock in N/m3 (lb per ft3). u= minimum velocity that must be imparted to the rock in m/sec (ft per sec). d= borehole diameter in m (ft).] The derivation used the impulse-momentum principle, with a 0.3 m thick (1 ft thick) radius of rock mass being acted on by an explosive impulse. However, the rock weight was not converted to mass by dividing by the gravitational constant. This mistake can be verified by checking the units in the formula, which resolve into m1/2-sec instead of meters. Adding the gravitational constant corrects this: [P d Atbmax =gu g = gravitational constant equal to 9.81 m/sect (32.2 ft per sec2).] If the minimum velocity is now taken as 0.3 m/sec (1 ft per sec), as was recommended, excessively large burdens result. Any appropriate rock velocity should be capable of throwing the rock mass a minimum distance so that the swell needed for breakage can occur. Unless the burden is extremely small and the bench height is very high, it is unlikely that a velocity of only 0.3 m/sec (1 ft per sec) will be sufficient. A review of the literature indicates that average rock velocities observed by camera studies typically range from 15 to 30 m/sec (50 to 100 ft per sec) (duPont deNemours and Co., 1977; Tansey, 1979). On this basis, a minimum rock velocity of about 15 m/sec (49 ft per sec) would be expected and not 0.3 m/sec (1 ft per see). When a velocity of 15 m/sec (49 ft per sec) is inserted into the corrected formula, the results approximate those of the original formula with a velocity of 0.3 m/sec (1 ft per sec). The errors were approximately self-compensating [(9 = 1.24)]. ? References Allsman, P.L., 1960, "Analysis of Explosive Action in Breaking Rock," Transactions, AIME, Vol. 217, pp. 475-476. E. I. duPont deNemours and Co., 1977, Blasters' Handbook, 175th Anniversary Edition, Dupont, Wilmington, DE, pp. 233. Tansey, D.O., 1979, "The DuPont Sequential Blasting System," CIM Bulletin, Vol. 72, July, p. 80. Thompson, S.D., 1981, "Critical Review and Revision of Surface Blasting Practice," MS thesis, West Virginia University, pp. 308-316.

Jan 1, 1986

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40' to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33' to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5' A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6'F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40' to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33' to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5' A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6'F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

By A. L. Mowry, John T. Norton

Isothermal sections of the pseudo-ternary carbide systems TiC-VC-ZrC, TaC-VC-ZrC, and NbC-VC-ZrC have been examined. The sections contain an inverted U shaped two-phase field whose maximum extent is 77 molecular pct for Tic, 64 pct for TaC, and 51 pct for NbC. lsoparametric lines were determined which show the curvature of the single-phase field and the direction of tie lines in the two-phase field. It was not possible to show any relationship between atom size and the extent of the two-phase field. REVIOUS work' on the solubility relationship of several pairs of refractory cubic monocarbides from the group Tic, ZrC, VC, NbC, and TaC has shown that, with the exception of the system VC-ZrC, they all form continuous series of solid solutions. It was demonstrated that the limited solubility in the case of VC-ZrC system was primarily a question of the size factor, the size difference between vanadium and zirconium being greater than the limiting value of about 15 pet. It is interesting to consider the results of combining these isomorphous carbides in groups of three and to determine the isothermal section of the pseudo-ternary diagram at, for instance, 2000°C, a temperature that will assure an equilibrium structure in a reasonable length of time. In the ternary systems where the three pairs form complete solid solution series, it is probable that the isothermal ternary section would be a single- phase field, although this is not necessarily the case. However, if one pair of carbides has a very limited solubility, then there must be a two-phase field of some extent, and it is the purpose of the present work to examine the extension of this field and to determine if it can be related to the nature of the third carbide. This condition is fulfilled if the VC-ZrC pair, which has only limited solubility, is combined with Tic, TaC, or NbC. The relative sizes of the metal atoms undoubtedly play a role in the extent of the single-phase field, and the values obtained from the pure carbides, assuming close-packing between metal and carbon atoms and a carbon atom diameter of 1.54A, are

Jan 1, 1952

By Sidney A. Swensrud

MUCH discussion has occurred as to the use or uses which might be made after the war of either or both .of the large diameter (24 inch and 20 inch) War Emergency pipe lines built by y the United States Government during the war, to move crude petroleum and refined products such as gasoline and light distillate fuels. Indeed, the disposition and future use of these lines constitutes, in the minds of many people, one of the most important problems of postwar readjustment in the Oil Industry. The two lines, running from points in Texas to the New York-New Jersey-Philadelphia area, were constructed only because of the inability during the war to continue normal ocean tanker movements from the Gulf Coast to the East Coast. Physically they could continue after the war to move crude or refined products, and it appears that lines of such large diameter as these, if operated at or near capacity, could move these liquids at costs per barrel which might be considered in the same general cost range as for tanker movements.1 If, therefore, we were to look forward at the end of the war to a shortage of tankers, it is probable that the continued use of these pipe lines for petroleum movements to the East Coast would be worth considering, as against building new tankers to take over the movement, provided there were no other economic or national defense reasons for restoring tanker fleets and no other better use for the pipe lines. Because of the extensive tanker construction program which has been and still is in progress, and because of our Navy's marked success in combating the submarine problem, it appears to be quite possible, however, that instead of a shortage of tankers at the end of the war, we may have a surplus instead. If this should turn out to be the case, then there would seem to be considerable doubt that these lines would continue to be used for moving petroleum or products to the East Coast at the expense of tying up tankers. It would hardly seem probable that the owner of any such tankers would ship via one of the large lines at the expense of tying up one of its own tankers, unless the pipe line tariff rate charged was lower than the out-of-pocket cost of operating a tanker as against the out-of-pocket cost of keeping it tied up. And considering that a substantial part of the cost of operating a tanker goes on even when it is tied up, it is very difficult to figure out how any pipeline tariff could be established that would be low enough to compete with individually owned tankers that otherwise would be idle. Certainly a pipe line tariff rate high enough to cover direct costs plus even a low rate of depreciation and return on the investment would be far above the out-of-pocket tanker operating costs. In view of these considerations, it has seemed desirable to examine with some care some of the various alternatives that have been suggested as to other possible uses to which these lines might be put. One of these is for transportation of natural gas to the New York-New Jersey Philadelphia area. This Eastern area, located at the destination of these lines, contains the heaviest concentration of population in the United States, and is not now served with natural gas. At the other end of the lines lie the greatest discovered natural gas reserves in the United States, if not in the world, and many

Jan 1, 1944

By John C. Smock

THE question of the proper valuation of mines of iron ore was suggested to me by the difficulties experienced in getting answers for the United States Census Office, while I was engaged in the work of collecting the statistics of mines in New Jersey and New York The answers to the questions relating to values of real estate of mine properties varied so greatly that it was necessary to revise them according to some general principles of valuation. Generally the returns of mine proprietors Seemed to be too low. There were, however, examples of what would be termed excessive valuation. The Subject appeared to be of practical importance, and led to the paper here presented. The following table of selected mine statistics is given, prefacing the discussion of the principles of valuation. It is in part made up of census returns and partly of data obtained directly from mine owners and managers. The mines which were Selected for the Several groups and mining districts include nearly all of those from Which the more full and carefully filled returns were received, and are also representative of their respective districts. Hence the averages obtained from them become good types of these groups or districts. The mines of New Jersey appear in Six groups, each containing from three to eleven mines, or, in all, thirty-four mines. The magnetic iron ores of New York are in four well-marked groups, and there are twenty-six mines in them. Then follow the red hematite mines of St. Lawrence and Jefferson counties; and, lastly, the brown hematite groups of Dutchess and Columbia counties, and those of the adjacent parts of Connecticut and Massachusetts. The whole number of mines represented by the table is eighty-eight, of which twenty-eight are hematite mines. The first column gives the value of the real estate; the second that of the plant; the third is the sum of these two, or the capital invested. Then follow the number of men employed, the amount of wages paid during the census year, and the value of materials used in mining and preparing the ores for market.* The seventh column gives the total expendi- * The value of materials is somewhat uncertain in many cases, as royalties are included under this head. Likewise, under wages, the cost of explosives and light is often included. Hence it is impossible to draw the line sharply between these items of expenditure.

Jan 1, 1882

By S. F. Bartram, G. A. Chase

COMPUTED X-ray diffraction powder patterns of YNi3, YNi5, and CbBe3 are available on request from either author.

Jan 1, 1968

[ ]

Jan 1, 1938

Herbert A. MegRaw, San Luis de la Paz, Guanajuato, Mexico (communication to the Secretary *):—I am in entire accord with the basis of Mr. Lamb's argument, that the stamp

Jan 1, 1911

By H. W. McCue, Henry Rogatz

Oil.—During the year 1939, there were 365 oil wells drilled in the Texas Panhandle, with a total daily initial production of 130,968 bb1.— that is, 69 fewer oil wells drilled than in the previous year, with a decrease. in total daily initial production of 61,738 bbl. The total daily potential of the field on Dec. 5, 1939, as determined by the Texas Railroad Commission, was 1,344,677 bbl., an increase of 94,032 bbl. over the previous year. On Dee. 5, 1939, a daily allowable of 130,527 bbl., which was an

Jan 1, 1940

By Henry Rogatz, H. W. McCue

Oil.—During the year 1939, there were 365 oil wells drilled in the Texas Panhandle, with a total daily initial production of 130,968 bb1.— that is, 69 fewer oil wells drilled than in the previous year, with a decrease. in total daily initial production of 61,738 bbl. The total daily potential of the field on Dec. 5, 1939, as determined by the Texas Railroad Commission, was 1,344,677 bbl., an increase of 94,032 bbl. over the previous year. On Dee. 5, 1939, a daily allowable of 130,527 bbl., which was an

Jan 1, 1940