Search Documents

Jan 1, 1938

Jan 1, 1951

By W. F. Tanner

A river delivers a given load of sand, and hence heavy materials, into the sea. The load is fixed by drainage basin characteristics and processes. Wave energy available for redistributing that load is fixed in an entirely different way. An equilibrium diagram of these two parameters (load vs energy) pennits a tentative prediction of what will happen to the heavy minerals. Alluvial rivers transport a mechanical load which consists essentially of wash load (finer than about 0.05 mm in particle diam), bed load (coarser than about 0.10 mm) and the transition sizes in between. A few rivers carry no appreciable mechanical load, and are excluded from this discussion. An example of the latter is the Suwannee River of Florida, which empties across an oyster bar into the Gulf of Mexico and does not build a delta despite the absence of significant waves or currents in that part of the Gulf. An alluvial river may deliver its load into a protected sediment trap (such as an estuary, sound or lagoon), onto a low-energy coast (where it builds a delta) or onto a high-energy coast (from which spot the river load is swept away). The nature and disposition of the load depends, obviously, on three sets of factors: 1) drainage basin characteristics and processes, which determine quantity and make-up of the load; 2) coastal structure and geomorphology, which determine the kind of river-sea coupling which

Jan 1, 1962

Jan 1, 1942

By A. Schild

The effect of heating a producing well on the rate of oil recovery has been analyzed in the simple case of a well producing oil by a radial drive and in the steady state. Differences of production rates with and without borehole heating have been calculated and plotted; these measure some of the benefits of the thermal recovery process. A striking feature is that the production increase tends rapidly to a constant value for large production rates. Some concrete examples, including a rough comparison with field data. are discussed. Heating requirements have been calculated and plotted on the assumption that the heaters used are 100 per cent efficient. Heating has been thought of as applying only to low volume wells producing heavy oils. However, the calculations suggest that the thermal process considered might be profitable even for some wells producing large quantities of light oil, especially in unconsolidated formations where fracturing is not possible. In the case of wells producing other fluids with the oil or of wells producing partly or wholly by gravity drainage, the theory developed does not apply in detail. It can be expected, however, that any general qualitative be-havior will remain valid. Under normal temperature conditions, high viscosity emulsions sometimes form around the wellbore, lowering the permeability in the vicinity of the well and impeding the production of oil. Borehole heating often prevents such emulsification. This important effect is not easily amenable to mathematical analysis and has not been included in the theory presented here. It should therefore be kept in mind that the benefits due to borehole heating may in fact exceed the values given by the following calculations. INTRODUCTION The recovery of viscous, low gravity oils can often be stimulated by applying heat to the production zone. The higher temperature lowers the viscosity of the oil, increasing its mobility, and therefore its rate of production. One thermal method of recovery 1,2,3,4. consists in operating a heater inside a producing well and, at the same time, producing oil from the well. In this paper a simple theoretical model is analyzed to study the effect of such heating on the recovery of oil. The reservoir mechanics of the process is the only aspect of the problem which is considered here. The details of the heating system are ignored, and it is simply assumed that the heater raises the temperature in the immediate vicinity of the producing well to a pre-assigned temperature T w. Although heating requirements are calculated, these refer only to the heat supplied to the formation and to the oil being produced; they do not include heat losses due to the inefficiency of the heater. A short outline of the theory follows: The heat supplied to the producing well flows out into the formation by means of thermal conduction. At the same time, the flow of oil carries heat by convection from the formation towards the producing well. After sufficient time has elapsed, a steady-state is reached where the temperature, the velocity of the oil, etc., no longer vary with time but are functions of position only. In the steady state the temperature decays like an inverse power from the high value Tw at the wellbore to the original reservoir temperature T. at some distance away from the well. The effect of the high temperature and low oil viscosity near the producing well is the same as if the oil were produced at reservoir temperature To but through a producing well of a larger radius. From this point of view, the energy and money being expended to provide heat

Jan 1, 1958

Jan 1, 1949

Jan 1, 1910

By G. Sachs, G. Espey

SIMPLE methods can be used for the determination of the residual stresses in thin-walled tubing if the stresses consist of high tensile stresses at the one surface and high compressive stresses at the other surface Such a stress distribution is approximated in sunk tubing and in deep-drawn shells It is possible to cut sections from such articles in such a manner that a major part of the residual stress is relieved by a bending of the part that is separated from the adjacent metal The circumferential stress is evaluated from the change in diameter D, occurring on splitting a length of tubing (Fig Ib),1-5 or from deflection resulting from the cutting out of a circumferential tongue (Fig Ia) G The bending moment M released by such a flexure is [ ] The release of this bending moment corresponds to the release of stresses, which, in a thin section, vary linearly from one surface to the other, and have the following value in a particular fiber a certain distance (zx from the surface [ ] where C is the section modulus and d is the thickness of the section, the ratio AI C being d 2 for a rectangular section* The maximum stress values at the surfaces are [ ] For most purposes the simpler equations [ ] will be satisfactory, where Dm is the average of the mean diameters of the tubing

Jan 1, 1941

[ ]

Jan 1, 1938

Jan 1, 1894

Jan 1, 1893

By H. C. Miller

THE gas-lift method of flowing oil from wells is the outstanding feature of petroleum technology today. Its forerunner, the air lift, was used successfully first, in the Baku fields of Russia, in 1899, and later in the Gulf Coast fields of Texas and Louisiana and the Kern River field of California. It is still used to a limited extent in certain oil fields. The use of compressed natural gas for lifting oil from wells has supplanted the air-lift method in a measure in those fields where a sufficient quantity of gas accompanies the oil to make the gas lift possible, or where natural gas is plentiful and inexpensive. We find therefore in California, that, natural gas is used at practically every well where a gaseous medium is employed to flow the oil. The use of natural gas has many advantages over that of air. It is possible to recover and save the gasoline from the gas that accompanied the oil to the surface. This gasoline would be wasted if air were used as the lifting medium. Also, certain proportions of air and gas form an explosive mixture that cannot be handled safely by compressors. Another advantage that gas has over air is that gas under pressure is more soluble in oil. Gas in solution in oil reduces the viscosity of the oil that is being produced and causes it to flow more readily through the. tubing and flow lines. The gas lift has made it possible to recover many thousands of barrels of oil from deep wells in California that could not have been produced otherwise. It would not have been economical, had it been mechanically possible to produce such wells as the world's deepest producing oil well (Miley Athen's No. 6, Rosecranz field, California) by any other method of pumping known today. At this well, production is obtained from between 7305 and 7591 ft. and 11 months after completion of the well, production was being maintained on the gas lift it approximately 2000 bbl. a month. The crookedness of the hole, or its diameter and depth will not prevent the successful application of gas-lift pumping when other conditions are favorable.

Jan 1, 1927

By Charles Himrod

IN presenting this paper it is not intended to enter into any discussion of the theory of the blast-furnace, but simply to give the results of a number of determinations of CO and CO2 in furnace gases, and some conclusions arrived at, and the result of an experiment made in hopes of increasing the production of CO2. In the first table, on page 198, is given the averages of a number of analyses of gases of different furnaces, and in the second, of two stacks of different sizes under varying circumstances. The conclusions arrived at as to what influences the production of CO2 are as follows: 1st. Kind of fuel. Bituminous coal not permitting the formation of as much CO2 as coke. 2d. Kind of ores. Rolling-mill cinder being much less favorable to formation of CO2 than hematite ores, magnetites probably less than hematites, but more than cinder. 3d. Length of time of contact of gases with ore. Small furnaces and too rapid driving both waste fuel by not allowing enough time for conversion of CO into CO2. 4th. The temperature of blast. The hotter the greater the quantity of CO2. 5th. Regularity of passage of stock through the furnace. The hanging and dropping of the stock, however slight, seems to pack it more solidly in the hearth, increases the resistance to the blast, and decreases the quantity of CO,. These are the most common causes noticed which influence the production of CO2, unless we except the one that might be considered the greatest of all, the one that has spoiled so many tons of iron, and the amiability of so many furnacemen, the one most dreaded, the great unknown. It would seem a self-evident proposition that the better the contact of the gases with the ore and the less with the fuel, the greater would be the amount of CO2 produced. To prolong the contact of gas with the ore furnaces are enlarged with advantage, and pains are taken to charge the stock in such a, manner as will best promote it. Still, with furnaces of most approved construction and most skilful manipulation, the gases leave the furnace so rich in CO, that not half the heating power of the fuel is obtained, and the highest

Jan 1, 1877

By Charles Himrod

In presenting this paper it is not intended to enter into any discussion of the theory of the blast-furnace, but simply to give the results of a number of determinations of CO and CO 2 in furnace gases, and some conclusions arrived at, and the result of an experiment made in hopes of increasing the production of CO 2. In the first table, on page 198, is given the averages of a number of analyses of gases of different furnaces, and in the second, of two stacks of different sizes under varying circumstances. The conclusions arrived at as to what influences the production of CO2 are as follows: lst,. Kind of fuel. Bituminous coal not permitting the formation of as much CO, as coke. 2d. Kind of ores. Rolling-mill cinder being much less favorable to formation of CO2 than hematite ores, magnetites probably less than hematites, but more than cinder. 3d. Length of time of contact of gases with ore. Small furnaces and too rapid driving both waste fuel by riot allowing enough time for conversion of CO into CO2. 4th. The temperature of blast. The hotter the greater the quantity of CO2. 5th. Regularity of passage of stock through the furnace. The hanging and dropping of the stock, however slight, seems to pack it more solidly in the hearth, increases the resistance to the blast, and decreases the quantity of CO2. These are the most common causes noticed which influence the production of CO2, unless we except the one that might be considered the greatest of all, the one that has spoiled so many tons of iron, and the amiability of so many furnacemen, the one most dreaded, the great unknown. It would seem a self-evident proposition that the better the contact of the gases with the ore and the less with the fuel, the greater would be the amount of CO2 produced. To prolong the contact of gas with the ore furnaces are enlarged with advantage, and pains are taken to charge the stock in such a manner as will best promote it. Still, with furnaces of most approved construction and most skilful manipulation, the gases leave the furnace so rich in CO, that not half the heating power of the fuel is obtained, and the highest

By John Birkinbine

A specimen of brown hematite, taken from an iron-ore mine near Anniston, Alabama, exhibits a metallic streak or thread running throngh it. This specimen having been sent to me, I have no personal knowledge of its occurrence; but Mr. Albert E. Noble

Jan 1, 1895

[ ]

Jan 1, 1938

Jan 1, 1932

Jan 1, 1918

[SATURDAY, FEBRUARY 16 10 am to 5 pm Council of Section' Delegates SUNDAY, FEBRUARY .17 1 pm Student Relations Committee 2 pm Board of Directors 2:30 pm MIED-Mineral Economics Instruction 5:30 pm MIED-Cocktails and Buffet Supper 7:30 pm MIED-Mineral Education 8 pm IMD-Program Committee]

Jan 1, 1952

Jan 1, 1919