Search Documents

By Kalanadh V. S. Sastry, D. W. Fuerstenau

Design and operation of a batch balling drum that can be used easily for experimental investigation of the balling or granulation behavior of particulate materials are described briefly. An experimental procedure for ascertaining the growth kinetics of iron ore concentrates or other particulate materials with this kind of apparatus is outlined.

Jan 1, 1972

By W. B. Lilienthal

A considerable saving in time and money has been effected by use of a specially designed stainless steel container for laboratory drilling mud test work. This container involves use of a standard tall-form stainless steel beaker for service in which the mud sample is heated to an elevated temperature and maintained there for protracted periods of time, while undergoing agitation to facilitate mixing of mud components. Agitation is accomplished by rotating the filled containers on motor-driven rollers within an oven. Several porcelain balls are generally placed in the containers to further improve agitation. Soft glass containers (.Mason jars) were used in this service in early work, and were found to be unsuitable for the following reasons: 1. Poor resistance to thermal shock. 2. Containers could withstand only relatively low pressures. 3. Accidental breakage in handling. 4. Chemical deterioration and subsequent mud contamination from reaction of high pH muds with the glass at elevated temperatures. Pyrex containers were also considered, but, inasmuch as they provided improvement only in items 1 and 4 listed above the additional cost was not believed to be justified. A scale drawing of the container is shown in the figure illustrating details in cross-section. A pressed stainless steel lid was fabricated to match the rolled edge of the beaker

Jan 1, 1950

By H. S. Chiang, D. F. Lu, S. S. Peng

INTRODUCTION The most important element in a successful lingual mining is a good roof control. The modern longwall mining employs hydraulic powered supports for roof control at the face area. The application of hydrau¬lic powered support requires the knowledge of over¬burden strata behavior for proper selection of sup¬port type and capacity. Failure to do so could lead so serious loss. There are several methods available for determining the required support capacity (1-3). While these methods are simple for application, they do not include the complicated roof behavior observed in longwall mining. As research progresses and operational experience accumulates (4,5), the concept about the designing and selection of powered support improves. The design of a longwall powered support consists of three major phases: 1. structural integrity and stability of the powered support, 2. external loadings induced by the movements of the overburden strata, and 3. interaction between the support, roof and floor. Phase 1 involves structural analysis (5) and full-sized testing (6) of the supports. Its validity is limited by the accuracy of the assumed external loading because of the uncertainty about the actual loading underground. The third phase includes the reaction of the support and the floor to the movements of the overburden strata and vice versa. Among the three phases, the second phase concer¬ning the external loading seems to be the least known because of the complicated behavior of the roof strata. There are many unresolved problems. For example, does the main roof break periodically and cause periodic roof weighting in the face area? If so, are there any rules governing its behavior? How does the roof load on the support canopy! Finally, how can one determine the required support capacity and select a proper type of support to meet a certain roof behavior? In order to answer those questions, underground instrumentation and observations were performed at 4 longwall panels in 3 separate mines for the past two years. This paper summarizes the current findings. PANEL LAYOUTS AND EQUIPMENT EMPLOYED The three mines selected are all located in West Virginia; two in northern and one in southern West Virginia. As shown in Table 1, seam conditions (i.e. seam, depth and thickness) and panel layouts are different among the three mines. The most significant difference in equipment is the face powered supports. Three mines used three different types of shield; 2-leg caliper, 2-leg lemniscate, and 4-leg lemniscate chock-shield. (Fig. 1) UNDERGROUND INSTRUMENTATION AND OBSERVATION PROGRAM Two events were instrumented in each observed longwall face: one was the hydraulic pressure (resistance) of the powered supports and the other was the canopy load distributions. In addition, the gob caving conditions were visually observed and recorded. Leg and Support Resistances One or two automatic Weksler Pressure Recorders were installed at the designated shield support,. In most cases, the daily charts were used to record the pressure variations in both the front or the rear legs (for the 4-leg shield), or in both the leg and the fore-pole ram (for the 2-leg shield). The recorded pressure w a s then converted to load or resistance by multiplying it by the cross-sectional area of the hydraulic leg or canopy ram piston. Fig. 2 shows the typical pressure-recorded charts for the 4-leg and 2-leg shields in a 23-24 hour period. The support resistance is the summation of the resistance in each of all the legs for that support. Generally, the resistance of the fore-pole ram will not be considered in determining the capacity of the support because of its rather small vertical compo¬nent force at the tip of the fore-pole. Canopy Load Distribution External load distribution on the canopy as exer¬ted by the roof was monitored. The measurements employed 12-14 pieces of pressure cells (6-inch square) that were uniformly arranged in two rows on the canopy. After support setting, the pressure changes in the cells were monitored at various stages of the mining (supporting) cycle while the support leg pressures were recorded continuously by the pressure recorders. Based on the calibration chara¬cteristics of each pressure cell as performed in the laboratory before and after each underground test, the cell pressures were converted to actual loadings. From these load measurements the canopy load distri¬butions and the relations between measured canopy loadings and support leg resistances were determined. Accordingly, the supporting efficiency of the shield support can be determined.

Jan 1, 1982

By David Kellogg

THE electrodeposition of iron has been practiced for many years. The earlier work along this line was directed toward the preparation of pure metal, but later applications were the production of thin adherent coatings as used in the electrotyping of Russian banknotes in 1860. A historical discussion of this subject, however, would require too much space and would be inconclusive. Much has been written on the subject but no two experimenters use the same methods or materials. During the war, the British army repair, shops developed a method for building up worn parts of automotive machinery, aero engines, etc., using the cold surfate . bath and low-current density method.1 The method has been used successfully in commercial work for the production of about 6000 repaired parts, therefore experiments along the same lines have since been made at the Westinghouse research laboratory. The apparatus used was essentially that described in the article mentioned except that the current -used for cleaning was obtained from a 3/4-kw. 60-volt, house-lighting generator, direct connected to a 2-h.p., 870-r.p.m., 440-volt, three-phase, type CS induction motor; while the plating current was taken from the storage batteries at any desired voltage. The anodes were made from 0.036 in. (0.9 mm.) Armco iron made into cylinders 5 in. (127 mm.) long by 8 in. (203 mm.) in diameter with a disk of 1/8 -in. (3.17 mm.) micarta, having a 2 in. hole in the center fitted at each end of the cylinder for stirring. The anodes were hung on a wooden rocker frame driven by a wooden connecting I rod directly connected to a small reducing gear, such as is sold by most of the apparatus supply firms; 3 gal. stoneware crocks were used as containers. The solution used by Thomas, 75 gm. of the crystallized ferrous ammonium sulfate per liter, was tried, using the current density recommended by him; namely, 0.33 amp. per sq. dm. Under these conditions the deposit on a ½ -in.

Jan 2, 1922

By Guilliaem Aertsen

THE derivation of the word tire (or tyre, as it is spelled in England) is obscure. Some dictionaries suggest that it is the aphetic form for "attire, covering," so called as being the outside covering or band of a wheel; also as a corruption of "tier," the band which holds, or "ties," the rest of the wheel together. One dictionary states: "The supposed derivation of the word is that bands were first used on wheels in the City of Tyre, Syria. " In the infancy of railroads, the tracks consisted of flat baits of iron, spiked or bolted to the upper surfaces of longitudinal timbers, which; in turn, rested upon masonry foundations. Stone blocks installed for this purpose on the old Germantown & Norristown Railroad, now the Chestnut Hill branch of the Philadelphia & Reading Railway, were to be seen for many years on the right-of-way, north of what is now. Wayne Junc-tion, Philadelphia, Pa. The "cornerstone" of the Baltimore & Ohio Railroad was laid Apr. 4, 1828, and the first locomotive in America was built by Peter Cooper at the St. Clair Works, Baltimore, Md., in 1829 "to demonstrate its adaptability to a curved road." It is believed that the first successful locomotive was built in Philadelphia by Tyler & Baldwin in 1832 for the Germantown & Norristown Railroad. Rufus Tyler-and Matthias Baldwin were brothers-in-law; the latter's name will he identified with American locomotives until locomotives are forgotten. The Wheels on these first locomotives, designed to run on this primitive rail, were shod with plain iron bands, bent and welded. The flanges consisted. of separate iron bands, bent sidewise, welded, and, bolted to the sides of the wooden follies, or rings. Before many years had elapsed the tires were fabricated of iron bands, rolled in one, piece with the flange projection on the side. The tire for each wheel was bent and welded and subsequently attached to the wheel center by shrinkage, bolts, rivets and various mechanical devices.

Jan 1, 1917

By C. M. St. John

INTRODUCTION The stress redistribution accompanying the excavation of a deep tunnel may induce failure of the rock. The role of the support system is to control the extent of the failed region and hence to limit closure of the tunnel within an allowable amount. In such circumstances, the design of the support system is generally based on the Ground Reaction Curve (GRC). The GRC is the relationship between the support pressure and the induced displacement at the tunnel wall for a circular tunnel under hydrostatic loading. In the calculation of the GRC (see Brown et al. (1983) for an exhaustive list of reference), the rock is generally treated as an elastoplastic material characterized by cohesive-frictional yield strength and by dilatancy during plastic deformation. A recent analytical development (Detournay, 1983) has allowed the generalization of the GRC concept for some cases of non-hydrostatic in-situ stress fields (Detournay and Fairhurst, 1982). As an application of that development, this paper describes design charts that provide powerful means of performing parametric analysis for tunnels subject to non-hydrostatic loading. BACKGROUND The in-situ stress in a plane perpendicular to the tunnel axis can be decomposed into mean and deviatoric components, Po and So (see Fig. 1). Since it is assumed that the rock is characterized by a Mohr-Coulomb yield strength, the deviatoric invariant So must be less than the limiting value Sl0 given by

Jan 1, 1984

By S. Fukushima, E. Kimura

In the Mitsubishi beneficiation process of ilmenite, chlorine is regenerated in the dechlorination furnace where the gases produced from a selective chlorination of ilmenite are directly introduced. The present paper describes a reaction mechanism and mixing characteristics of the reactant gases for dechlorination of ferric chloride with oxygen. A furnace of a small diameter where the reactant gases passed through in the state of nearly plug flow was used for determination of the effects of temperature and of partial pressures of ferric chloride and oxygen on the rate of the reaction. The experimental data of the reaction rate were applied to various models for calculations of the rate equations and the most suitable reaction model was determined. The results of the experiments also showed that effects of gas mixing onto the reaction rate could not be ignored, so that experiments of gas mixing was carried out. Gas flow patterns and scale effects were observed with use of transparent model furnaces of different sizes.

Jan 1, 1976

By B. Zondek, W. T. Cardwell, J. W. Sheldon

The fundamental equations that are used to describe two-phase fluid flow in porous media are Darcy's law for each phase and an equation of continuity for each component. The special case of one-dimensional, incompressible, two-phase flow has received much attention in the petroleum engineering literature.1-10 The basic paper on the subject is that of Buckley and Leverett.2 Buckley and Leverett showed that one could eliminate the pressure and obtain a single partial differential equation for the saturation. They solved this equation for the case when gravity and capillary forces are negligible. A frequently encountered property of the solution of the basic partial differential equation is that, as time progresses, the saturation becomes a multiple-valued function of the distance coordinate, x. Buckley and Leverett interpreted the formation of multiple values as an indication that the saturation-distance curve had be-come discontinuous. They developed a method of determining the position of the discontinuity from a material balance. We solve the Buckley-Leverett partial differential equation using the method of characteristics and the concept of shocks. Our treatment is analogous to treatments used in the theory of supersonic compressible flow." Although the numerical results obtained are the same as those obtained by previous methods, we believe that this approach is more logical and has broader applicability. It can, for example, be generalized to treat the case when the fluids are compressible. It is not clear how one would go about doing this using the method of Buckley and Leverett. To illustrate the power of the method of characteristics with shocks, we solve a problem in gravity segregation which has not been treated previously in the literature. A special case of the general method developed here was used by Welge, to solve a particular fluid displacement problem. We consider two-phase incompressible flow along the vertical direction x in a porous medium. We assume that there is no flow transverse to .x. We measure positive in the upward direction. The fundamental equations are obtained from Darcy's law and the mass conservation law. Since the two phases are incompressible, mass conservation is equivalent to volume conservation.

By F. Brons, W. C. Miller

Pressure information for use in material-balance calculations is obtained, where possible, from pressure build-up surveys in shut-in wells. Using proper extrapolation methods, static pressures are obtained which, by averaging, give the field static pressure. Often, particularly in fields with a large number of wells, only spot pressure readings are available. A graphical method is presented here which enables the determination of the corrections which must be applied to the spot readings to give an estinzate of the static pressure. Although the static pressures thus obtained are not so reliable as those from build-up surveys, they are more nearly correct than the spot readings themselves for use in material-balance calculations. INTRODUCTION The average static pressure in a bounded reservoir is determined from a number of individual-well pressure measurements. Where pressure build-up curves are available, extrapolation methods such as described in Ref. 3 may be used to determine the static pressure in the drainage area of each individual well. The possibility of using pressure build-up curves presupposes that each well being surveyed is closed in during a certain period and that, during this time, a pressure recorder is left suspended in the hole. For surveys in fields with a large number of wells, this is usually not feasible for economic and other reasons. Either a large number of pressure recorders would have to be used simultaneously or, using a limited number of recorders, the time interval needed to complete a field-wide survey would be too long. The data obtained for this incomplete coverage are insufficient to permit reliable averaging of the few calculated static pressures over the entire reservoir. In many such cases another type of pressure information is available, i.e., spot pressure readings. During this type of pressure survey all wells are closed-in simultaneously and, after a reasonable shut-in time (e.g., three days), pressure readings are taken by running the recorder in and out of each successive well. These surveys, which are less expensive, are often taken at regular intervals, say once or twice a year. In fact, such surveys are required by the state regulatory bodies in many portions of the united States. These spot readings are normally lower than the static (fully built-up) pressure due to the relatively short shut-in time. No direct means of extrapolating such a reading to the static pressure is available because no pressure build-up record is obtainable. Consequently, these data are inferior to pressure build-up information as a basis for estimating the stabilized reservoir pressure in the drainage area of a specific well. For the common case where abundant spot readings but only a few pressure build-up surveys are available, our studies suggest that it may be possible to design a program which will combine the two types of information and provide an estimate of the average reservoir pressure that is more reliable than that obtainable solely from either set of data. in time) gives a point marked p. The actual static pressure at the time the well was shut-in is marked by p.. The illustration shows that, even if a build-up curve is available and can be extrapolated, a correction

By A. Romero-Juarez

This paper is concerned with the effect of propping-agent concentration on flow capacity of a fracture in the case in which there is embedment of the propping agent. Previous published studies have shown definitely that there is a relationship between fracture flow capacity and prop ping-agent concentration, and it has been shown that the theoretical results are confirmed by laboratory experiments. The problem of directly finding sand concentration for maximum flow capacity of a sand-propped fracture is solved, and formulas and charts are given to obtain this concentration under various conditions of effective overburden pressure, medium sand-grain diameter and rock properties. It is shown that, for the same effective overburden pressure and the same rock characteristics, optimum sand concentration in pounds per gallon does not depend on medium sand diameter. For conditions met in bydraulic fracturing operations, it is found that sand concentration in grains per square inch for maximum flow capacity varies within a wide range of values; this indicates the convenience of using data of fracturing pressure and rock characteristics for calculating sand concentration in order to achieve the best results in fracture treatments. INTRODUCTION It has been pointed out in the published literature1 that one important factor controls the success of a hydraulic fracturing operation — the propping of the fracture. The main effect of the propping agent is to hold the fracture open by means of the reaction forces that oppose the pressure due to the overburden. It is assumed in this paper that the propping agent is sand, that the grains are spherical and uniform in size, and that this sand is distributed in a monolayer in the fracture. The existence of a sand concentration value for maximum fracture flow capacity has been recognized since the publication of one of the first studies on the subject.2 In the reference cited, flow capacity was assumed to be proportional to the cube of the fracture volume per square inch not filled by sand. The obtained experimental curves relating to flow capacity and sand concentration had the same appearance as the curves obtained with the afore-mentioned assumption. Recent work3 has shown that fracture permeability, in the case of a monolayer, can be calculated accurately by means of a modified Kozeny-Cacman equation; thus, it can be shown that fracture pqmeability is a function of free volume in the fracture and of the rock and sand wet surfaces. The flow capacity of a fracture is dependent on the permeability of the fracture and on the fracture width. If all excessive quantity of sand is present in the fracture, its width may be large but its permeability i:; low due to the greater flow resistance; too few grains of sand per square inch are present in the fracture, sand embedment in the rock is greater and the width becomes small enough to appreciably decrease the rate of flow. To determine optimum conditions of flow, therefore, it is necessary to know the dependence of fracture width on density or concentration of propping agent. This relation is given in a study4 in which the approach to embedment is similar to the one made in a penetration hardness test of metal. With the equacions presented by Darin and Huitt,3 the number of sand grains per square inch that results in maxirnum fracture capacity can be determined graphically by plotting fracture capacity vs sand concentration. Since the relationship between fracture capacity and sand concentration may be considered known, one is led to formulate the analytical problem of directly determining sand concentration for maximum fracture flow capacity, in order to study the effect of the various quantities that come into the process. The solution of this problem appears to be interesting both from the viewpoint of fluid mechanics and from the practical viewpoint of oil production in hydraulic fracturing treatments. EQUATION FOR FRACTURE FLOW CAPACITY It can be shown3 that the fracture flow capacity of a monolayer is given by the following expression,

By R. N. Orava, L. A. Rice

One of the difficulties encountered in the preparation of titanium specimens for transmission electron microscopy is the formation of a surface hydride phase during the thinning operation at ambient temperatures. This necessarily destroys contrast, obscures features of interest, and often leads to misleading results. By cooling the polishing solution to temperatures below 0°C this problem has been overcome in the past.' However, since the cooling procedure is somewhat inconvenient, a technique was developed at this laboratory for thinning titanium at room temperature. The material examined was A-70 grade commercial-purity titanium purchased from the Crucible Steel Co. of America. The mechanical and thermal treatments, described elsewhere,* yielded a recrystallized grain size of 4 to 5 p. A slice, 0.5 mm thick and 1.5 mm wide, was cut from a bulk specimen2 using a diamond cut-off wheel. The sample was then coated with paraffin wax. Two concentric holes, about 0.03 in. in diam, one at each broad face, were scribed through the wax to the surface of the metal. Subsequent polishing for several minutes resulted in a preferentially thinned or "dimpled" region. Thereafter, the wax was removed and the entire specimen polished to the point of breakthrough at the base of the dimple. Polishing was effected chemically in a solution comprised of 30 pct HF and 70 pct HN03 by volume, kept at room temperature (20" to 25OC). The specimens were mounted in a stereo holder and examined at 100 kv in a Philips l00 B Electron Microscope. A micrograph from a foil prepared in this way is shown in Fig. 1. Several points are noteworthy. This electron micrograph shows neither evidence for the formation of a hydride phase due to specimen preparation nor, moreover, any obvious surface contamination in electron-transparent areas of a freshly prepared foil. Localized variations in foil thickness observed in some specimens seem to be a characteristic of this chemical polish but do not seriously detract from foil quality. With care, the lifetime of a good specimen exceeded 2 hr in the beam. On the other hand, the exposure of a sample to air at atmospheric pressure, when still warm from the beam, clearly resulted in the deterioration of a formerly clean area just previously in the field of view. An example in Fig. 2 of a contaminated region reveals features, and "spots", not unlike those observed in much purer material by Yamane and Ueda. Consequently, one can conclude that: 1) titanium can be thinned satisfactorily in a solution at room temperature for transmission electron microscopy; 2) large-scale precipitates, >50A in diam, are absent in commercial-purity, recrystallized, furnace-cooled, A-70 titanium containing about 3800 wt ppm interstitials and the same amount of iron; 3) care must be taken not to attribute surface contaminants to precipitates. The authors are grateful to the Franklin Institute for financial support and permission to publish.

Jan 1, 1967

By W. J. Parton

The efficient recovery and preparation of small sizes of anthracite called No. 4 Buckwheat (3/32 by 1/32 in.) and No. 5 Buckwheat (1/32 in. by 0), pre-sent a difficult problem to the anthracite operators. In many instances preparation of these sizes, particularly No. 5 anthracite, is extremely inefficient. In many of the older preparation plants, inadequate facilities, and often none at all, were provided as an integral part of the plant for cleaning this fine anthracite. Consequently, much of the material smaller than 3/32 in. was discarded. As the demand for these sizes increased, facilities for preparing the fine sizes were often crowded into existing structures with consequent sacrifices of capacities and efficiency. In addition to this condition, the methods of preparing the finest sizes are being developed in an attempt to improve their efficiencies. Because the demand for small sizes of anthracite still is increasing, many operators would benefit by investigating and improving the cleaning equipment employed on these sizes. The object of this paper is to de- scribe a stationary screen device from which the underflow is restricted by orifices, called a launder screen, along with operating results of several applications of this screen; a settling tank in which two classified products are produced by the installation of a cylindrical partition of smaller diameter than the original tank, one product being recovered from the small tank created by the partition and one product from the space between the inner and outer tank walls; a small pocket classifier or hydraulic trap for use in removing high ash particles from a sludge flow; the classification or segregation of sludge solids occurring in a 16 in. diam pipe flow by analysis of samples procured at different zones; and the operating results of a Fahrenwald sizer, as well as the performance of the concentrating tables handling the classified products. These simple devices were employed at the collieries of the Lehigh Navigation Coal Company Incorporated, Lansford. Pa., in order to improve preparation results on the fine sizes of anthracite. Launder Screens The launder screen is a screening and dewatering device which probably could be used advantageously in the flow diagram of many fine coal plants. Fig 1 shows that it consists of a stationary screen constructed by placing 6 in. high partitions every 6 in. along a launder. Holes are then drilled on 6-in. centers across the bottom of the launder to receive pipe bushings of the desired diameter. The screen cloth is tacked on top of the partitions. When water and solids are fed to the screen, only a small portion of the total water is removed through the orifices in each compartment so that the water in the feed is distributed evenly over the whole length of the screen. The screening action which results is very efficient because the solids are kept in a fluid condition for the full length of the screen. Blinding of the screen can be minimized by the use of screen cloth

Jan 1, 1950

By Ralph Wilcox

The diamond drilling of certain characters of unstable rock formation, as, for example, the copper-bearing schists of the Miami district in Arizona, is rendered most difficult by what is known as a caving " of the sides of the drill holes. As this caving is very greatly increased by the action of flowing water, it occurred to me, after experiencing a great deal of difficulty with caving in diamond-drill holes which I was drilling for the Miami Copper Co., that if I could substitute air for water, much of the caving—with resultant difficulties, such as decreased speed of sinking and increased consumption of diamonds—would be overcome. After some experimenting, I found that it was perfectly practicable to substitute air for the water; forcing the air down the hollow rotating rods in the same manner as is done with water, the air passing out around the bit, which is thus cooled, and ascending on the out~ide of the rods to the collar of the hole, carrying the borings in just as satisfactory a manner as had been done by the water, but without the accompanying destruction or caving of the sides of the drill holes such as had been so generally experienced with the water. When water was encountered in the drilling this water was forced up to the collar just as it would have been had water been used in the drilling, but with the correspondingly decreased flow there was relatively less washing or caving of the sides of the drill holes. The only change necessary in the arrangement of the drill is that a cross instead of a tee is used at the collar of the hole. A tightly woven jute bag is attached to one arm of the cross, for collecting and filtering the sample; and when drilling in dry ground a jet of water is attached to the opposite arm of the cross, to collect the dust and wash down the sample into the bag. The rods rotate through a stuffing box attached to the upper opening of the cross. The distention of the jute bag by the issuing air indicates the operating conditions as sufficiently as did the flow of water when using water in the drill hole. The small percentage of core recovery rendered it necessary to

Jan 1, 1914

By R. W. Nelson

Methods for determining permeability presented by W. D. Kruger3 in a paper entitled "Determining Areal Permeability Distribution by Calculation" have considerable merit. They can be expected to contribute significantly to analysis of flow in heterogeneous systems. Some rather subtle yet important conditions must be met, however, to assure that the computed permeabilities are correct. The conditions which insure a unique permeability distribution may have been overlooked in the method as proposed and presented in the subject paper. The subtlety of the special requirements may permit good agreement between computed and measured pressures in the reservoir; but the computed permeability may still be in error. The general theory and discussion of the requirements for a unique determination of the permeability distribution are presented elsewhere in more detail.7'8 Accordingly, only major features will be presented here in the notation of Kruger. GENERAL DESCRIPTION OF REQUIREMENTS A brief mention of the route to be followed in showing the special requirements may be helpful. The equation to be solved is a quasilinear, first-order, partial differential equation in the unknown permeability. This equation can be solved through an extension of Lagrange's method by reduction to a system of subsidiary ordinary differential equations. Through consideration of the identity of one of the Lagrange subsidiary differential equations with the stream function, a special interrelationship can be shown. The interrelationship has special significance with respect to the boundary condition. If the boundary function satisfies part of the subsidiary differential equation, no unique solution for the permeability distribution exists. In the physical problem this requirement for uniqueness indicates that the permeability measurements used as a boundary condition can not be along a stream tube. The boundary condition must be along a line, or series of lines, which completely traverse the region and pass through every stream tube.

By H. Landsberg

MANY of the sedimentary rocks contain small amounts of radioactive constituents. These vary in quantity in different layers. Some recent deposits show rather high activity as; for example, the deep sea oozes and some lake deposits.1,2. Measurements made in boreholes have also shown considerable changes in activity from horizon to horizon. The first to publish data on this fact was Ambronn,3 and recently Russian geophysicists have shown remarkable variations of activity from one layer to the next in various wells. Spak4 felt even that he was able to line up horizons from data measured in two neighboring wells. ? The measuring of radioactive radiation is fairly difficult. Large errors are possible by the circulation of gaseous emanations in the well and porous strata. It is, therefore, never certain whether the activity of the layer where the instrumental device or collector is located will be measured, or that of some adjacent layer, For this reason it seemed to be advantageous to take samples of rocks into the laboratory and test them therefor their contents of radioactive material, Such a method has been followed in the past to distinguish radioactive ore from other rocks. Radioactivity of rocks, especially of the igneous type, was also deter-mined in the laboratory by numerous authors for absolute age investi-gations.6 Corresponding data from studies of sedimentary formations are scarce. Specimens taken from a core of the Bradford oil sandstone were tested by Landsberg and Ingham,7 with the results illustrated in Fig. 1, which shows that within relatively small vertical distances the differences of relative activity were considerable. If one assumes that the distribution of radioactive material is fairly uniform throughout a layer, measurements of radioactive radiation in various horizons would offer additional information for stratigraphic

Jan 1, 1939

By Edward C. John, Wilbur H. Smith

At the Bingham Canyon pit operated by Kennecott's Utah Copper Division, the demand for geology has recently grown and diversified so rapidly that it has necessitated a revolution in geologic mapping techniques. The most significant changes in method have been in the preparation of the base map and in the computer application of collected data. Formerly maps were prepared by surveying with a transit or plane table. Now, however, a photogrammetric map with a scale of l in. to 200 ft is prepared semiannually and updated continuously to keep pace with the removal of more than 350,000 tons of material a day. Larger-scale bases of areas with specific problems such as un- stable slopes are prepared with aerial and terrestrial photography and photo-mosaics. Note sheets designed for computer application speed the processing of data. The multiplying applications of geology at the Bingham mine now include studies of the effect of structure, rock type, and alteration on slope stability, the relationship of sulfide mineral distribution to concentrating results, the effect of rock and mineral types on waste dump leaching, and the requirements of a reliable internal source of silica flux for smelting, as well as many others.

Jan 9, 1969

By J. H. Palm

Experiments have shown12 that the formula -S = St - (St - Se')e ne [1] expresses very well the relation between the true stress S and the true form monotonic deformation of plastic metals in single tension and compression (Fig 1). St (asymptotic or final stress), Se' (threshold stress) and ne (characteristic or specific strain) are constants, the significance of which immediately follows from Fig 1. Only at the initial stages of deformation the experimental curve runs below the theoretical curve. This may be due, at least partly, to the uneven stress distribution caused by the anisotropy of the crystals. It is now obvious that a similar formula H = Ht- (Ht- He)e ne' [2] might be valid for the relation between the hardness and the strain. The hardness can be only a function of the strain and must therefore be independent on the hydrostatic tension present in the neck during straining. Hence, if Eq 2 is correct it will also represent the relation between hardness and strain in the middle section of the neck, the strain of which is generally assumed to be almost or fully homogeneous. For aluminum, copper, and several copper alloys it is indeed observed that Eq 2 agrees very well with the experimental Vickers hardness-strain relation from zero strain on up to the strain at fracture. Moreover nc' is, for several metals fairly equal to nc- Hence H = C1 + C2S [3] C1 and C2 are constants during uniform uniaxial tension. Eq 3 was also obtained for copper by Voce.3 According to Hencky's theory4 the ratio of the Brinell or Vickers hardness and the yieldstress (expressed in kg per mm2) of a non-strainhardening metal is approximately equal to 2.8. If Eq 1, 2 and 3 are correct the ratio Ht/S, must accordingly be the same for all plastic metals and be equal to 2.8. It is now experimentally established that this ratio varies between 2.7 and 3.1 with a mean value of 2.9. Taking into account that Ht and especially St can be obtained only by extrapolation from the range of rather low strains, the agreement with the theory is very satisfactory. References 1. J. H. Palm: Appl. Sci. Res. Al (1948) 198. 2. E. Voce: Jnl. Inst. of Met. (1948) 74, II, 537. 3. E. Voce: Metal Treatment (1948) 15, 53. 4. H. Hencky: Zlsch. f. angew. Math. and Mech. (1923) 3, 241.

Jan 1, 1950

Jan 1, 1918

Jan 1, 1920

By E. C. Kersey, R. J. Gennone

MetALLOGRAPHIC investigations of composites of zinc alloys and aluminum have been made to study the effects of various thermal treatments on the zinc-alloy grain size and diffusion of zinc into the core material. The use of various alloys of zinc has necessitated the development of a universal etchant which will allow microscopic examination of the zinc grain size regardless of the composition.

Jan 1, 1960