Search Documents

By J. D. Livingston

THE hardening of alloys by the precipitation of a second phase has long been an important technological process. One approach towards improving our understanding of this phenomenon has been a correlation of mechanical properties with such parameters as particle size and inter par ticle spacing.' Several reviews of such data have appeared.2-4 A major limitation to this approach has been that for most alloys the particles are submicroscopic in size in the range of optimum hardness. Precipitation-hardening copper-cobalt alloys, therefore, are of interest, because the ferromagnetic properties of the precipitate make it possible to measure particle size, number of particles, and so forth, from magnetic measurements alone.5, 6 Livingston and Becker7 have applied these techniques to a study of precipitation hardening in an alloy of 2 pct Co in copper. It was found from magnetic measurements that nearly all the cobalt to be precipitated was out of solution within a few minutes at 600°C, whereas the peak in tensile yield stress was not attained until a much longer aging time. Thus during the first 1000 min of aging time at 600°C the Yield stress was increasing while a constant volume of precipitate was coarsening, i.e., while particle size and interparticle spacing were increasing. Peak yield stress was reached at an average particle radius of about 70A. The earlier study was confined to one alloy at one aging temperature, so that the volume fraction of precipitate was fixed and, therefore, particle size and interparticle spacing could not be independently varied. The work has now been extended to several alloys of varying percentage cobalt in copper, and to aging at various temperatures. It was hoped that such a study might clarify the relative importance to precipitation hardening of particle size, interparticle spacing, and volume fraction of precipitate. EXPERIMENT The alloys studied contained 0.7, 1.3, 2.0, and 3.2 wt pct Co in copper. They were prepared from electrolytic copper and electrolytic cobalt in a vacuum -induction furnace, worked to 3/8-in.-diam rod, and machined into tensile specimens with a gage section 1 1/2 in. long and 3/16 in. in diam. All specimens were given a solution treatment consisting of a 30-min anneal in nitrogen at 1000° C followed by a quench into iced brine. Subsequent aging was done in nitrogen and followed by a water quench. Average grain diameter was approximately 0.01 in.

Jan 1, 1960

By Donald W. Scott

GENERALLY speaking, there is nothing very difficult about taking good micrographs of photogenic thin sections or grains with a petrographic micro-scopecamera setup. However, sometimes it is desired to show some detail that cannot be illustrated satisfactorily by the usual micrographs taken with parallel polarized light, with crossed nicols, or even with two micrographs. A simple procedure giving good results has been used at Battelle Memorial Institute for subjects falling into this classification, and it is believed to be of interest, especially to research people who must sell a point to executives through the medium of well-illustrated reports. The following problem illustrates a typical application: It is desired to photograph a thin section of an iron ore to illustrate the character and association of the iron oxides and the individual quartz crystals. A magnification of 75 dia. is acceptable. A micrograph of the field in question (Fig. I[a]) was taken with parallel polarized light. Due precaution was taken to provide critical illumination, correct exposure, a sharp focus, a good darkroom technique, and other essential conditions. It illustrates correctly the iron oxides, but it fails to show the individual quartz crystals. A micrograph of the identical field (Fig. I[b]) was taken under the same precise conditions, but with crossed nicols. It gives a better idea of the character of the individual quartz crystals but is likely to be misinterpreted unless accompanied by a lengthy descriptive note. This micrograph suggests that the centrally located, large black area is composed entirely of iron oxides. That this is an incorrect interpretation is evident by reexamining the micrograph of Fig. I[a]. The correct interpretation is that the dark area contains quartz crystals oriented with their optical directions parallel to, or nearly parallel to, the vibration directions of the polarizer and analyzer of the microscope. Thus, the executive, or anyone who had not done the work personally, would get no more than a fair interpretation, even if two micrographs were included; and in the interests of both brevity and clarity, one micrograph usually is more desirable. Exactly how many quartz crystals occur in this region cannot be told from the two micrographs, and a printing of the two negatives in register would likewise not show the detail desired. Thus, it is evident that some subjects cannot be satisfactorily illustrated by the usual procedures. In photographing Fig. is the light was subdued and, during the entire exposure of 75 sec., the analyzer nicol was rotated uniformly in its mounting from a crossed position to 45° uncrossed position to introduce the desired amount of contrast in the various individual quartz crystals. The true reproduction of the character and association of the iron oxides, and the additional structure and detail in the quartz areas, is apparent. It might be

Jan 1, 1946

By S. E. Bretherton

Mr. AllaW Gibb, of Mount Perry, Queensland, Australia, in an interesting and instructive paper,* describes fully the great difficulties metallurgists encounter in seeking to produce marketable copper by smelting refractory ores containing arsenic, antimony and bismuth. After reading this description, I prepared a paper for the Institute, which was, however, through a misunderstanding on my part, published in the San Francisco Mining and S'cie~ztiJic Press of April 4, 1903, after its acceptance by the Council, and without credit to the Institute. Consequently, it cannot be reprinted for the Transactions of the Institute; and I can only here summarize its contents and conclusions, referring the reader to the article above named for further particulars. In that article I omitted the col~sideration of bismuth, which we do not encounter in our smelting at Val Verde, and added lead and zinc, which Mr. Gibb had not discussed; and I undertook to shorn, by the record of a year's practice of the Val Verde Copper Co., Arizona, that copper-ores containing arsenic, antimony, lead and zinc may be successfully smelted, without preliminary roasting, in an ordinary blast-furnace with hotblast, making a normal slag, such as one would aim to make under ordinary conditions with cold-blast, so as to produce a marketable matte, containing not less than 45 per cent. of copper, free from arsenic and antimony, and below the limit in lead and zinc penalized by the refineries.

Jan 1, 1904

Jan 1, 1912

Jan 1, 1908

Jan 1, 1911

Jan 1, 1909

Jan 1, 1910

Jan 1, 1913

By Robert Job

Up to five years ago the pig-iron used by the Philadelphia & Reading Railway Co. had been obtained solely upon the appearance of the fracture; but as the service was unsatisfactory, an investigation was made to determine the quality best adapted

Jan 1, 1905

By M. J. Greaves

All available data concerning risk as it applies to scaling up pyrometallurgical plants, processes, and equipment are determined to estimate the statistical chance of success. Random numbers are assigned to all data in order to avoid any chance of bias. The data bank is organized in such a way that an estimate can be made of the degrees of risk involved over a wide range of circumstances. Included are duplicating existing designs and large commercial installations based on smaller commercial installations, pilot models, or bench models.

Jan 1, 1977

Jan 1, 1913

The technique of hard facing can be a quick and economical means of prolonging wear-life of many metals, but maintenance personnel must first select the proper alloy from the hundred that are available. Even then, roper selection is effective only when it is properly applied by the welder. To complete the successful weld, several hints are offered:

Jan 4, 1978

By N. D. Policow, J. S. Orphanos

Dewatering fine clean coal fractions, -595µm (-28 mesh), represents one of the most difficult and costly separations in typical plant circuits. Since 1969, the screen bowl centrifuge has offered an economical alternative to filtration/thermal dyer combinations. The performance of screen bowl centrifuges has been continuously modified and improved to dewater not only coarser coals, but also today's variety of ultrafine material. Test comparisons with alternative methods show the screen bowl centrifuge to be most cost effective and efficient when all factors are considered.

Jan 1, 1984

CLARENCE N. FENNER.-Mr. Gelstharp, chief chemist of the Pitts-burgh Plate Glass Co., has directed my attention to the fact that that company was using optical pyrometers obtained from the Leeds & Northrup Co. several months before the members of the Geophysical Laboratory arrived at Charleroi. I am glad to make this correction. The chief object of my paper was to emphasize the necessity of careful temperature control in the making of optical glass and to describe the kind of tests to which an optical pyrometer should be subjected at a glass plant in order to obtain information regarding the closeness with which its readings correspond with true temperatures under the condi-tions which prevail in each particular case.

Jan 12, 1919

By Robert W. Hunt

No matter how perfectly sectioned or skilfully manufactured the rails used may have been, or with what care the road-bed may he maintained, legitimate results from these important factors cannot be secured unless proper attention is bestowed upon the joint-fastenings. In this country, splice-bars of various patterns furnish the practically universal joint. Other forms have been used, and are now being experimentally tested, but the typical American rail-joint consists of angle-plates or splice-bars. At the same time, it is true that scarcely a railroad engineer is satisfied with his joint. He may consider it the best of which he has knowledge, but at the same time he is well aware of many of its weak points.

Jan 1, 1890

By C. D. Jardine, D. G. Patton

Rapidly increasing energy costs and more rigid customer quality requirements necessitate improved control of pelletizing processes. With the introduction of dedicated microprocessor-based controllers, sophisticated control strategies are now possible. An application of this technology at Carol Project has resulted in fuel savings, improved pellet quality, and standardization of operating procedures. This was accomplished with no production loss by using a "building block" approach to design and equipment selection.

Jan 1, 1985

Here are the details . . . . . of how a $2.5 million research gamble, now backed by five years of intensive development in cooperation with the Chemical Construction Corp. resulted in a hydrometollurgical process that yields pure metal powders from sulphide concentrate - a process that offers potential savings of $2.5 million a year.

Jan 6, 1953

By Massimo Guarascio

Computer data processing and ore reserve evaluation techniques, mainly based on geostatistical methodologies, have been developed at Agip Mining Division with the assistance of the Department of Mining Engineering of the University of Rome. A number of computer programs are available when facing problems such as optimization of sampling patterns, minable reserve estimation, grade control of output, and so on. In the present paper, the aims and the criteria followed in developing these programs are discussed. Some recent examples of application are also cited.

Jan 1, 1977

By H. F. Walther

Basic electric-are furnace steel production mainly involves the use of two separate types of slags. The first, known as the "melt down" or oxidizing slag, which is in most cases removed from the furnace mechanically, and the heat finished under the second or deoxidizing slag, which is commonly known as the "finishing slag.'' The melt down slag is formed by the addition of lime or limestone to the charge, which combines with the oxides formed during the melting period and the product of any bottom erosion that may take place.

Jan 1, 1935