Search Documents

Jan 1, 1888

Lester Guttman (General Electric Research Lab-boratory)—Seybolt has measured the thermodynamic activity of silicon in dilute solution in a iron. The anomaly which appears at 800 °C in the approximate range 1 to 6 wt pct Si is most naturally attributed, as Seybolt has done, to the existence of a region of

Jan 1, 1960

By J. L. Lytton, J. E. Dorn, L. A. Shepard

Single aluminum crystals were subjected to creep in simple shear on the (111) planes in the slip direction. The activation energies for creep were calculated from the effect of small abrupt changes in temperature on the creep rate just before and immediately following the temperature change. The results definitely establish the fact that creep of single aluminum crystals occurs by-three unique processes, characterized by thethree distinct and isolatable activation energies: The 35,-500-cal-per-mole activation energy obtained at the highest temperatures was ascribed to a dislocativationtion climb process; the 28,000-cal-per-mole activation-energy process, occurring over the intermediate-temperature range was attributed to a cross-slip mechanism; and it was suggested thot the 3400-cal-per-mole process observed below 400°K may be the Peierls energy. THE most pertinent question regarding the phenomenon of creep in crystalline materials is concerned with the identity of the crystallographic mechanisms of deformation that control the creep rate. For many years slight progress was made in uncovering the basic mechanisms for creep. Over the past 10 years, however, two parallel lines of investigations have contributed to a more definitive understanding of the processes involved in creep. The extensive development and maturing of dislocation theories for deformation of crystalline materials' proved to be of paramount importance for this progress. And second in importance was the replacement of the former prosaic methods of creep testing by new techniques'." which were especially

Jan 1, 1959

By Clifford Wilson

SCREENED pipe is designed with the view of restraining the fine, free-running sands of the production zone from entering oil wells. Its successful use is dependent on a number of factors. The nature and effects of some of these factors can be determined through experiment and observation, but some of the elements that have a distinct bearing on the use of screened pipe can be evaluated only by estimate. The important subsurface conditions which affect the use of screened pipe are: 1. Depth of production zone. 2. Extent of production zone. 3. Reservoir pressure. 4. Character and relative quantity of oil and gas. 5. Character of sediments a. Consolidation of beds. b. Variation in beds. c. Grain-size gradation of sands. d. Free-running characteristics of sand from different levels. Aside from the use. of mechanical equipment and tools, the measures to be taken in the installation of screened pipe involve: 1. Size of liner. 2. Length of liner. 3. Design and mesh of screen. 4. Portion of liner to be screened. 5. Manner of setting liner. 6. Preparation of or washing of the well before or during the setting of the screen. 7. Manner of bringing in the well. 8. Manner of flowing the well. Values applicable to the actual subsurface conditions that exist at any well can only be approximated. The accuracy of the estimate will be measured by the amount and quality of the evidence at hand and the personal factor of ability to interpret the evidence fairly, whether

Jan 1, 1932

Ore deposits of commercial grade are local concentrations of great rarity when considered in relation to the area of unmineralized land surfaces, and they must therefore be considered as the products of exceptional and complex conditions. The data collected from a great number of individual deposits are sufficient to permit certain broad generalizations in regard to the conditions favorable to ore deposition which even numerous exceptions do not invalidate. The broadest general relation of ore deposits is with intrusive rocks, and while there are notable exceptions, the great majority of ore deposits have a visible or closely inferred connection with intrusive rock masses. Conditions that permit the dissipation of the ore-bearing vehicles do not permit the concentration of metals in deposits; the prime factor to consider in this connection is that structural conditions must be such as tend to concentrate and not to dissipate the ore-bearing solutions. The disadvantage of extrusive rocks is at once apparent; any metals the magma may have contained are dissipated at the surface and are lost; with the exception of tiny vugs and cracks in quickly cooled flows, no concentrations of metals are known in extrusive rocks, and the lack of confinement and quick cooling apparently do not permit extrusives to exert mineralizing effect upon the rocks with which they come in contact. The close mineralogical similarity between extrusives and intrusives, and the great difference in mineralizing power is a proof of the ease with which magmas part with their metallic content, and of the mobility of the ore-bearing vehicles in comparison with the parent magma.

Jan 1, 1932

By R. S. Cartwright

Two types of automatic drilling controls, the Halliburton and the Hild, are now available and are coming into more or less general use in deep drilling. The primary function of both is to maintain a safe limit of torque on the drill pipe, this being accomplished by automatically controlling the weight or pressure on the cutting tool. Neither type will necessarily increase drilling speed, but by permitting advantage to be taken of "breaks" in the hole higher average cutting speed may be maintained. The control is essentially a safety device, and should be considered as such. It is not the purpose of this paper to discuss the merits of drilling controls, although the advantages over manual feed at the brake drum are obvious, but rather to point out some of the limitations. The Halliburton Control The Halliburton control is designed to operate during drilling through the agency of the draw works. Automatic and constant control. of the torque on the bit is governed by clutches on the control itself, and the line shaft to drum shaft drives on the draw works. In operations other than drilling the control is simply a jackshaft between prime mover and draw works. It is, of course, adaptable to any type of power. Because control of the torque on the bit is dependent upon the various ratios or clutch combinations available on the Halliburton control and the draw works, it follows that there are certain limitations in points of control. Table 1 shows the possible ratios which can be obtained with the control and a popular type of three-speed draw works, it being assumed that the highest possible gear combination-the combination which when engaged will suspend the least amount of weight-has a value of 1.00.

Jan 1, 1928

By S. R. Goodman, Hsun Hu

A study has hem made of the formation of annealing textures in an 18-8 austenitic stainless steel (Type 304L) from various deformation textures obtained by rolling at different temperatures. When the deformation texture is a mixture of the ferritic type and the brass type owing to the pres -ence of both martensitic ferrite and retained aus-tenite in the specimen, recrystallization takes place by the growth of the existing austenite phase. In a previous report,' it was shown that the rolling texture of austenitic stainless steel (Type 304L) changed gradually from the brass type to the copper type with increasing temperature of deformation above 200°C. These changes are similar to those in high-purity silver2,3 and electrolytic copper;4 a brass-type texture is favored at low rolling temperatures, whereas a copper-type texture is favored During the course of rolling -texture transition from the brass type to the copper type, the subsequent recrystallization textures change accordingly. The orientation relationship between the annealing textures and the various rolling textures, being consistent with previous observations on various fcc metals, can be described as [Ill] rotations of approximately 25 to 40 deg. Carhide precipitation may influence the annealing textures. at high rolling temperatures. Furthermore, the annealing textures in high-purity silver5 and electrolytic copper4 were found to depend entirely on the prior deformation texture. From a copper-type rolling texture a strong cube texture will form upon recrystallization, whereas from a brass-type rolling texture the annealing texture will be quite different from the cube orientation. In an earlier comm~nication,6 the formation of a strong cube texture in 18-8 austenite stainless steels (Types 304 and 304L) was reported briefly by the authors. The present paper constitutes the results of a complete study of the annealing textures obtained from a

Jan 1, 1965

By A. T. Tye

REGARDING the results of preferential flotation at Cananea, Weinig has stated that "The concentrating mill of the Cananea Consolidated Copper Company at Cananea, Mexico, furnishes an excellent example of modern flotation practice. The complete figures are given because they present so forcibly the advantages of modern selective flotation."' L. 0. Howard notes that "Perhaps the outstanding example so far published of improvements in results through the use of selective flotation is that at Cananea, Mexico."2 The following notes indicate the conditions under which the results were obtained at Cananea; also the effect of preferential flotation at the concentrator and at the smelter. In the majority of cases the full benefit of selective flotation is not fully realized, as the concentrates are shipped from the mill to smelters owned by other companies. The saving made at a certain concentrator by this method of flotation may be well understood but the saving resulting at the smelter from the results of preferential flotation at the mill is not so apparent, as the data are contained in the smelting records of some other company. Even at the smelter the great gains following preferential flotation may not be noted, as a variety of ores and concentrates from various sources are received and the difference from the changed concentrator operations of a certain mill may be obscured. As noted by Professor Weinig and Professor Howard, the results obtained at Cananea brought about a veritable metallurgical revolution at the smelter.

Jan 1, 1927

By E. S. Greiner

Germanium and silicon have been plastically deformed in torsion at elevated temperatures. Slip took place on the four {Ill} planes. Dislocations, revealed by etch pits on a (111) face, occurred in rows that were traces of operative slip planes. THE plastic deformation of germanium and silicon by bending and tension at elevated temperatures has been reported by Gallagher.&apos; Transla-tional slip during plastic flow in these materials, according to Gallagher&apos; and Treuting,&apos; occurs on (111) planes. Recent work by Treuting&apos; indicates the direction of slip to be <1l0>. The present paper describes the plastic flow characteristics of germanium and silicon deformed by torsion. Torsional deformation was accomplished by twisting 1/4x1/4x2 in. specimens held in molybdenum grips and contained in an atmosphere of helium in a transparent quartz tube and heated by an external resistance furnace. The angular displacements were measured on a graduated circle with a pointer attached to the movable grip. Temperatures were measured with a chromel-alumel couple; the hot junction was within the quartz tube and in close proximity to the specimen. Photographs of samples of germanium and silicon twisted at 850" and 1180°C, respectively, are shown in Fig. 1. The germanium was twisted 230" per in. and the silicon 80" per in. These deformations are larger than those used in experiments to be described later and are presented only to emphasize the extensive plasticity of these materials. Germanium A single crystal specimen of germanium (n-type, 7 ohm-cm resistivity) with a (111) plane normal within 3" of the torsion axis, Fig. 2, was chemically polished with CP-4 solution" and then twisted 9" during the twisting of these specimens of germanium, the slip lines from the (lli) plane should have appeared in the four lateral faces instead of in only two. Perhaps the absence of rotational slip is brought about by the square cross-section. A cylindrical specimen would have a more uniform stress distribution in torsion than one with a square cross-section, and may deform by rotational slip. A specimen of germanium (n-type, 5 ohm-cm resistivity) twisted less than 8" per in. at 550°C, was cut to expose the (111) face 19" 28&apos; from the torsion axis, Fig. 4a. This face, after metallographic

Jan 1, 1956

By O. D. A. Pease, C. D. Young, C. H. Strand

In an effort to employ cast steel of a stronger structure than that found in the annealed steel casting, the possibilities of heat treatment which will increase the strength without materially decreasing the ductulity may be resorted to.

Jan 1, 1915

NORTH AMERICA Number Members Alaska 36 Canada 323 Mexico 184 Newfoundland 3 United States Alabama 40 Arizona 111 Arkansas 8 California 646 Colorado 171 Connecticut 90 Delaware 21 District of Columbia 136 Florida 16 Georgia 7 Idaho 66 Illinois 208 Indiana 66 Iowa 11 Kansas 24 Kentucky 32

Jan 1, 1934

THE opening session* was held in the hall of the Franklin Institute, on Tuesday evening, June 20th, President Holley in the chair. The President introduced. Mr. Franklin B. Gowen, who addressed the Institute as follows MR. PRESIDENT AND GENTLEMEN : It has been made my pleasant duty to welcome you to the city of Philadelphia, but in so doing I shrink, with some natural reluctance, from appearing before an audience so much better fitted than I am to cope with the subjects which are usually presented to your association, and I can assure you that no trembling neophyte, first venturing within the groves of the Academy, or walking, with sacred reverence, in the gardens of Plato, felt more natural dread at the consequence of his own temerity than I do in appearing before an audience composed of gentlemen belonging to a scientific society of which I am but too sensible that until now I have been a member only in name. In olden times, upon entering a temple sacred to the worship of any deity, it was customary to lay some offering upon the altar, and, in following this custom, it will be my duty, before entering upon the more pleasant part of the task which is assigned me, to call your attention to a subject with which I have been somewhat familiar, and which is entirely within the scope of your investigations, in the belief that I may throw out some hints or some suggestions of a pro¬cess that may be fully developed by some of you, and eventually lead to the introduction of that which may be of service to the human race. The satirist who described the philosopher whom he met, as engaged in the process of extracting sunbeams from cucumbers, * A joint discussion of the subject of Technical Education, by the members of the American Society of Civil Engineers and the American Institute of Mining Engineers, was held in the hall of the Franklin Institute, on Monday evening, June 19th, and Tuesday morning, June 20th. This discussion has been printed in a separate pamphlet by both societies.

Jan 1, 1877

By E. Lancaster-Jones

THE gravity magnitudes obtained by means of observations with the Eötvös balance in the field are necessarily resultant or total effects due to all abnormalities of mass distribution, including even the effects due to the ellipticity and rotational motion of the whole earth. Since the object of the survey is to isolate the effects which arise solely from some particular subterranean feature, and to deduce therefrom the configuration and extent of this feature, the first step is to eliminate from the observed effects all those due to "disturbing" (i. e., unwanted) features, whether above or below the surface of the ground. The disturbing features have different characteristics, according to their situation relative to the center of the balance and to the horizontal plane through the foot of the balance, or station point; this diversity was recognized by Eötvös, who divided the total effects into so-called Normal, Terrain, Topographical, Cartographical and Subterranean effects. This classification has been adhered to by most subsequent investigators, but the writer prefers to employ the term "three-dimensional," which really indicates the essential character of the class of effect known as "Subterranean," at any rate from the standpoint of the computer of effects. Before disturbing effects can be eliminated, the features must be measured up or surveyed, whether by topographical, mining, or boring methods, and then the effects of each feature calculated and subtracted from-the total observed effects. After this the problem of interpreting the residual effects will itself necessitate the computation of the assumed feature, or even a series of trial features.

Jan 1, 1928

By G. Sachs, S. I. Liu

INTRODUCTION IN a previous investigation on the effects of repeated strains of large magnitude on the aluminum alloy 24ST, it was found that the reduction in ductility by straining in tension was partially restored by a subsequent compression.&apos; As illustrated by the dashed line in, Fig I,§ the ductility (EF) retained after prestraining in tension by a certain amount (EI) and measured in a subsequent tension test is represented by a straight line sloping down under 45°. If a compression of the same magnitude as the first tension is inserted (E2 - EI) between prestraining and final testing in tension, such a "balanced" tension-compression cycle yields a ductility considerably higher than that present after prestraining in tension only. . The results of these tests can be correlated with those of an investigation on the effects of prestraining in compression.2 As also shown in Fig I, the ductility in subsequent tensile tests decreased with compression, at a rate considerably slower than that after prestraining in tension. The above discussed testing conditions can be considered as special cases of a general straining cycle, consisting of first, straining in tension by an amount E1, subsequently straining in compression by an amount E2, and finally determining the retained ductility, Ef, in a tensile test. Prestraining in tension is then represented by E1 > o and E2 = o. Prestraining in compression is given by E1 = o and e2 < o. Balanced cyclic straining is defined. by the condition E1 > o and E2 = -El. In order to obtain further information on the effects of straining cycles consisting of tension and subsequent compression, further tests were made, varying both the tension strain, E1, and the compression strain, E2, within extreme limits; El varied between 0.06 and 0.28 and E2 between -0.008 and -0.60 approximately. Apparently, such tests have not been previously performed. They revealed phenomena which have not been recognized to date. The results of the investigation are herewith reported, without attempting to correlate them with internal processes within the metal structure. However, in order to assist in an analysis of this type, the results have been represented in various manners. In addition, further test data on the effects of prestraining by compression were provided by using specimens of various contours (notched specimens) in the subsequent tensile tests.

Jan 1, 1948

By Jun-Yan Chen

Ground control problems in sublevel caving become evident as the rock pressure increases with depth. Recently, a finite element analysis of the stability problem of the sublevel caving method was completed by the author. This paper summarizes the results of stress analysis in sublevel extraction drifts under different field stress conditions by using linear elastic and nonlinear elastic-plastic finite element modeling techniques. A critical stress concentration will occur in the uppermost sublevel drifts beneath the caved area or blasted ore area. During the blasting and drawing cycle, a tensile and shear failure condition could develop in the center extraction drift when it would be mined last. Under a high horizontal stress field condition, almost all tensile stress in the back of the extraction drifts will be eliminated and only slight yield can be seen in the floor of the extraction drifts. Compared to the cases under the stress field where vertical stress is the dominant factor, the total yielding zone will be greatly reduced because of an in- creasing horizontal stress field with depth. However, it is predicted that the center of each ore column side will experience excessive shear stress that probably will result in ore failure. The two major conclusions drawn from this study to improve the overall stability of sublevel caving are: (1) the drift width must be carefully controlled and an appropriate stoping sequence selected; and (2) the sublevel caving method can be used in deep min

Jan 1, 1983

By C Gunther

The classification here used is one of convenience only; it is not intended to include all known types of ore deposits. The characteristic features of the several well-marked types of primary mineralizations are described without reference to the ultimate source of their metals. The minerals of many deposits of obscure origin were probably introduced through fissures that are now healed, or are due to the migration of metals from such deposits. It is not within the scope of this book to enter into a general discussion of the genesis of ore deposits but, in view of the progress being made in our comprehension of the conditions under which ore deposits were formed, mention should be made of recent work. J. E. Spurr&apos;s two volumes, "The Ore Magmas," are recommended as crystallizing the views of those who are inclined to ascribe the origin of most ore deposits to a differential precipitation from magmatic rock masses and to the migration and precipitation of the viscous, liquid or gaseous exhalations from those masses. He has especially emphasized the role

Jan 1, 1932

NORTH AMERICA Number Members Alaska 31 Canada 302 Mexico 175 Newfoundland 3 United States Alabama 52 Arizona 131 Arkansas 9 California 723 Colorado 184 Connecticut 98 Delaware 19 District of Columbia 133 Florida 16 Georgia 6 Idaho 61 Illinois 241 Indiana 57 Iowa 7 Kansas 32 Kentucky 33

Jan 1, 1932

By Myrick N. Bolles

The concentration of gold and silver in mattes low in copper, and the subsequent separation and recovery of either or both of these metals, is a question the satisfactory solution of which has long vexed metallurgists. It covers a broad and important department of metallurgical science and brings in its train a series of attendant problems continuing from the initial operations of concentration to the final recovery of " values."

Jan 1, 1905

Jan 1, 1961

By Samuel B. Christy

Jan 1, 1889