Search Documents

By Herbert H. Kellogg

DEPOSITS of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine (-325-mesh) sand assaying 95.5 per cent Si02, and a very fine (-3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. EXPERIMENTAL PROCEDURE The Sample.-The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotation Feed.-By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine fraction was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper.

Jan 1, 1945

By R. M. Stewart

INTRODUCTION Requirements for achieving economic slope stability in open pit mining must not only be met during the operating stages but in all preceding stages of mine development. In many operating mines little or no emphasis was ever placed on evaluating the stability of possible slopes during the exploration and planning stages. The purpose of this discussion is to emphasize the necessary considerations that should be made in all stages of development in order to achieve the safest and most economic pit slopes. The most economic slopes may not always be the safest slopes and it is incumbent upon the mine operators and engineers to achieve an optimal combination of economics and safety. The stability requirements outlined are based on the profit motive and are, therefore, practically oriented. Long-term basic research or theoretical studies are considered important only to the extent that they can be shown to have a definite payoff. Consideration will first be given to the information required for stability analysis, which can be determined during the exploration and evaluation stage, followed by further stability work necessary during the mine planning and layout stage. Particular emphasis is then placed on the operating stage in which blasting, dewatering, artificial stabilization, and slope failure are discussed. Lastly, the importance of a logical and orderly research procedure is stressed. EXPLORATION AND EVALUATION STAGE The purpose of the exploration and evaluation stage in the mining scheme is to find and delineate a potential orebody. Discovery and delineation commonly involve drilling tens and in many cases hundreds of boreholes. These boreholes, which may cost as much as $20.00 per foot of depth for a cored hole, are usually abandoned once drilling is completed. Stability evaluation for a potential open pit should begin at this stage by taking advantage of the existing boreholes. Rock and soil properties, as well as hydrologic parameters, may be obtained from both the borehole and the core. Seismic velocity and neutron probes may be used to log the borehole to obtain elastic moduli data. A borehole dilation jack may also be used to give backup information on the rock and soil elastic parameters. Use of a core orientation system can result in the determination of fault and joint frequency and distribution. Before splitting or otherwise disturbing the fresh core, qualitative evaluation

Jan 1, 1972

By Paul K. Krueger

SUMMARY Since 1970 the Federal Preparedness Agency has been using computer models to help establish the amounts of strategic and critical materials to be held in the National Stockpile. Fifty-three of these materials are metals or minerals. The following diagram shows the linkage of models used to estimate material requirements. [ ] The starting point for the models are estimates of the major components of GNP for some future period. These may be estimates purchased from a forecasting service or may be produced in-house. The projections are translated into industrial final demands using DITT (Demand Impact Transformation Tables), a system developed at FPA. Then using a version of the current Bureau of Economic Analysis input-output model, estimates are made of the gross output of each industry necessary to support the level and composition of GNP as specified by the macro-economic model.

Jan 1, 1977

By R. C. Good

Slag control for any kind of steel, rimming, straight carbon or alloy, should start with the charge and be developed well in advance of the tap because its composition, viscosity and temperature will unquestionably govern the physical and chemical properties of the steel when tapped. In the majority of plants producing alloy steels, primary consideration is given to the chemical specifications; physical characteristics usually occupy secondary place in the melter's mind. Recently, however, buyers have indicated limits of machinability, hardenability, grain size and, of course, always wanted steel free from foreign nonmetallic inclusions. It is these latter specifications that require the attention of the operator to the slag and its control. The slag must act as a vehicle for oxidized elements originating from the metallic portion of the charge; it should hold the oxides of phosphorus, silicon, manganese, iron and chromium that come into contact with it either before or after the refining and finishing stage of the heat. It must be used as a transferring medium of oxygen from the atmosphere or oxide additions to the metal and should permit a free escape of gas generated within the charge. Finally, the slag is the principal controlling factor in regulating the rate of oxidation which in turn eventually determines the quality of the steel as measured for the various characteristics mentioned above. With pig iron of uniform composition, the iron oxide in the slag increases as the limestone is increased but with the same addition of stone in every heat, the iron oxide decreases as the silicon is increased in the charge, and vice versa.

Jan 1, 1935

By R. C. Good

Slag control for any kind of steel, rimming, straight carbon or alloy, should start with the charge and be developed well in advance of the tap because its composition, viscosity and temperature will unquestionably govern the physical and chemical properties of the steel when tapped. In the majority of plants producing alloy steels, primary consideration is given to the chemical specifications; physical characteristics usually occupy secondary place in the melter's mind. Recently, however, buyers have indicated limits of machinability, hardenability, grain size and, of course, always wanted steel free from foreign nonmetallic inclusions. It is these latter specifications that require the attention of the operator to the slag and its control. The slag must act as a vehicle for oxidized elements originating from the metallic portion of the charge; it should hold the oxides of phosphorus, silicon, manganese, iron and chromium that come into contact with it either before or after the refining and finishing stage of the heat. It must be used as a transferring medium of oxygen from the atmosphere or oxide additions to the metal and should permit a free escape of gas generated within the charge. Finally, the slag is the principal controlling factor in regulating the rate of oxidation which in turn eventually determines the quality of the steel as measured for the various characteristics mentioned above. With pig iron of uniform composition, the iron oxide in the slag increases as the limestone is increased but with the same addition of stone in every heat, the iron oxide decreases as the silicon is increased in the charge, and vice versa.

Jan 1, 1935

By W. J. Whiten

Current developments in one type of crushing and screening model is reviewed and general design techniques and policies are proposed for the control of crushing plants.

Jan 1, 1984

By Paul Levin

A coal preparation plant built with conventional materials only might be able to do an efficient job of preparing coal, but its maintenance costs would be high and emergency shutdowns frequent. To remedy this situation special materials are being used, either in original plant construction or for replacement of conventional materials. The special materials vary from high-strength and abrasion-resisting steels and stainless steel alloys to ceramics. They include hard surfacing welding rods, rubber refractories and some of the newer plastics, the merits of which are cited by the author. A coal preparation plant, limited strictly to the use of conventional materials-for example, mild steel, cast iron and ordinary rubber-could, no doubt, do an efficient job of preparing coal, but the high cost of maintenance and increasingly frequent emergency outages would soon force the operator to seek relief by introducing special materials such as alloyed steels, oil-resistant rubbers and hard-surfacing welding rods.

Jan 6, 1964

By L. Adler

A fairly complex analysis is required to select or evaluate a piece of excavating and bulk handling equipment for its performance. At present, there is little agreement as to what points should be considered, and even less on what procedure to follow. This paper provides both of these in a consistent and direct form. The analysis applies to all types and sizes of equipment. The importance of the equipment characteristics, job activities, and work conditions are stressed. Separate analytical stems are established in a flow chart for these. They are combined using suitability tests in: problem statement; natural conditions; suitability guidelines; appropriate equipment types; operational activities; encumbered space; geometric design; equipment sizing; failure and limits; performance and consumption; public policy checks; and costs and profitability. Public policy and economics receive emphasis towards the end. The procedure is iterative, containing distinct feedback loops. Specifying the steps and sequence provides a necessary structure which has long been overdue.

Jan 1, 1985

Until the end of 1960, the small primary aluminum industry in Australia was run by the government. The entire operation was at Bell Bay on the north coast of Tasmania. It consisted of an alumina plant and smelter, owned jointly by the Commonwealth and the State of Tasmania. Apparent domestic demand that year was about 48,000 long tons; 11% thousand came from Bell Bay; the rest was imported. By March 1964, Australia had two fully integrated aluminum companies. The government has stepped out of the picture and the key word of the industry from bauxite to metal is "growth." Present annual capacity of the two companies for making aluminum metal totals 92,000 long tons a year. Australian demand is about 60,000 tons. By 1968 Australian consumption should be 90,000 tons and by 1970 it is expected to reach 107,000 long tons per year. Export markets for bauxite, alumina and metal are developing.

Jan 10, 1964

By William Daly

THE application of artificial refrigeration, or air-conditioning, to the ventilation of deep, hot mines has long been a subject of interest to the operators of such properties. Artificial cooling of the air in theaters, railroad coaches, and various industrial plants has been so successful within recent years that it has been natural to assume that the adoption of similar methods would afford a ready solution to the difficult problem of mine ventilation. It should however, be obvious, that although there may be nothing technically impossible in the application of this process to mine ventilation there is a great economic distinction between the maintenance of a high standard of comfort for a large number of people in a relatively small space such as a theater and the cooling of air to improve working conditions for miners scattered throughout the extensive workings of a large mine. Many methods of air-conditioning have been considered by the management of the Anaconda Copper Mining Co. at various times, but until the development of the process to be described in this paper none has seemed economically practicable.

Jan 1, 1934

By Roswell Johnson

THE principle of sliding or graduation in royalties is accomplished either by the block, period, cumulative, or class method. The block method calls for a very low royalty rate on all oil produced up to. a certain amount. This amount would normally be that which is believed to suffice to repay the cost of the well. A higher rate would be charged after the well is making a profit. This method, common in many industries, is peculiarly inadaptable to any industry such as this where the productivity per day of the units gradually and inevitably decreases. This, for reasons given later, is because it forces an early abandonment of the well and so offends against conservation. In the period method, the royalty rate is changed by some definite amount when the well produces less than a specified quantity per day or other given unit of time. While simple to explain, it operates badly because a great deal is made to depend upon a small reduction in production, whereas the reduction as a matter of fact declines rather erratically owing to the exigency of lease management, connecting of tankage, and vagaries of the gaugers. These disadvantages are obviated by the cumulative method. In this method, all the production less than a certain amount per week has one rate of royalty, or none at all, and the oil produced in excess of that amount pays an additional rate of royalty. In the long run the calculation is probably no greater than with the period method, for simple tables will be published and printed in the oil papers that can be cut out, enabling quick readings to be made. Even without the table the calculation is easy with the few royalty rates, two or three, which would be used. In this method, the amount paid in royalty declines gradually, rather than suddenly as in the period method.

Jan 6, 1915

By Frank Clemens Smith

The occurrence of the tellurides of gold and silver, even in small quantities, is so rare that their metallurgical treatment has engaged little attention. A residence of several months at one of the few mines in North America the product of which consists entirely of such ore, has led me to arrange a method for its economical treatment. The mine referred to is the Huronian, situated a few miles distant from Jackfish Lake, in Ontario, Canada. The plan proposed is for this peculiar case, and is put on record as possibly suggestive and helpful .in any similar instance, should it occur. Since freight-rates from the mine to the nearest railroad-point were extremely high, and for other economical reasons, the method proposed is modified by the use, as far as possible, of the machinery already at the mine, and is so arranged that bullion instead of concentrates would be obtained as a final product. The ore-vein at the Huronian mine varied in width from about 4 feet at the surface to 2 feet and less at the lowest level—125 feet —and dipped southeast about 88. The rock consisted, on both foot- and hanging-walls, of soft, green Huronian slates carrying much highly crystalline but barren pyrite. The ore carried an inconsiderable amount of galena with iron and copper pyrites, argentite, hessite, sylvanite (or petzite), and probably altaite, the telluride of lead. Near the surface the ore showed considerable native gold, but this disappeared with greater depth. Two complete analyses of minerals containing tellurium are here attached, as they establish the presence of two important compounds: I. Analysis of a mineral supposed at the mine to be sylvanite, but agreeing more closely in composition with petzite (Ag, Au)2 Te: Ag = 41.062 Au =23.691 Te =32.007 Pb = 0.071 SiO2= 0.097 Fe = trace 96.928

Jan 1, 1890

By Alexander Gakner

Since the end of World War II the Soviet Union has made great strides toward economic development of the country. Today it is firmly established as the world's second largest industrial power after the United States and it has committed itself before the people on both sides of the Iron Curtain to catch up with and to overtake us within a few decades. No nation could achieve such a degree of industrialization or aspire to become the world's industrial leader without a large supply of many basic mineral raw materials or at least easy access to such resources. In addition, it requires technical competence, a large skilled labor force, and a high rate of capital investment. Why should we concern ourselves with these Soviet aspirations? The Free World's yardstick of measuring a nation's well-being is the standard of living of the people in that country. Presumably even Communist governments are committed to some, however gradual, improvement in the standard of living of their people. The population of the USSR is 20 pct greater than that of the United States. Hence, if they ever achieve a standard of living equal to ours, they must by all logic reach a greater overall industrial output. However, in the U.S.S.R. the standard of living of the masses has not kept pace with the expanding industrial production and is still far behind that of the United States. Our concern, therefore, is with what the USSR intends to accomplish with its expanding industrial power: Will they produce large mineral raw-material surpluses and manufacture products to compete with us for world markets and attempt to put us out of business if not use it directly to wage war; or will they use their resources merely to produce more consumer goods for the Soviet people; or will they, along with other Communist nations in the not-too-distant future, compete with us for the world's sources of mineral raw-materials to maintain a high level of mass consumption?

Jan 6, 1960

By Granville S. Borden

THE program for income tax legislation presented here proposes some diminution in the current tax burden on mineral producers but it will, if enacted, eventually increase the potential and current Government revenue from the mineral industry.

Jan 6, 1951

By Kenneth N. McLeod, Donald W. McGlashan

In the use of free bubbles with precise temperature control and continuous pH measurement, the contact angle apparatus differs from all previous equipment. Experimental procedures differ sharply from the captive bubble method of introducing the gaseous phase in the three-phase system. When freed from the tube and captured by a solid surface, a bubble more closely conforms to the spherical ideal set up by the usual mathematical analysis of surface free energy or surface tensional relationships of the forces involved. The assembled equipment, Fig. 1, departs from the usual contact angle apparatus in providing: 1) water circulation for fixing temperature, 2) instruments to measure and record pH during testing, and 3) a system for producing and using free bubbles. The apparatus allows testing over a broad range of closely controlled conditions, and the use of free bubbles gives contact angles independent of operator manipulation, which was unavoidable in the older captive bubble method. A bubble released below the specimen rises through the liquid and contacts the mineral. If the mineral is gas-avid the bubble adheres, developing a finite contact angle.

Mar 1, 1956

By F. P. Haver, M. M. Wong

The Federal Bureau of Mines has developed a leach= electrolysis method for recovering lead from galena (PbS). Flotation concentrate is leached with ferric chloride (FeCl3) solution to obtain lead chloride (PbC12) and elemental sulfur, PbS + 2FeC13 -+ PbC12 + 2FeC12 + Sº. Over 99% of the P~S in the condentrate is converted to PbC12. The leach solution, composed of brine (NaC1) and FeC13, dissolves the PbC12 as it is formed, leaving a residue of elemental sulfur plus gangue. Very pure PbC12 (>99.9%).is crystallized from the leach filtrate on cool- ing and is subsequently electrolyzed in a fused-salt bath to obtain molten lead metal (>99.9% Pb). Spent leach solution (FeC12) is regenerated for further use by reaction with the chlorine obtained in the electrolysis of lead chloride, and other values, such as Ag, Cu, Zn, and Sº, are recovered by additional treatments of the leach solution and leach residue. This paper discusses results and conditions of the leaching and electrolysis operations.

Jan 1, 1976

By R. F. Stewart, A. W. Hall

A method has been developed for continuously measuring the moisture content of coal. The method is based on the thermalization of fast neutrons by hydrogen in the coal. Neutrons from a small radio-isotope source penetrate the coal, are scattered by hydrogen, and measured by a thermal neutron detector. The number of thermal neutrons counted can be directly correlated with the moisture content of coal. In a pilot-scale system, moisture was measured continuously within 0.2% in coal moving at rates up to 20 tph. The method is adaptable in industry for continuously measuring the moisture content of coal at high tonnage flow rates. Such an application would permit continuous recording of moisture in coal without sampling and facilitate quality control. An automatic and continuous method of measuring the moisture content of coal is needed by the coal industry. Automatic control of the coal quality would reduce the cost of coal preparation, improve the product, and thus indirectly increase the use of coal. Moisture in coal can be determined by several methods, but the time required to obtain samples and analyze them by existing methods makes it difficult, if not impossible, to control the quality of the product. Both producers and consumers need a method for continuous and instantaneous measurement of moisture content without sampling in order to regulate process equipment and keep the moisture content of coal within specifications. At the Morgantown, W. Va., Coal Research Center we are developing a nuclear method for continuous measurement of moisture in coal. This method is based on the thermalization of fast neutrons by hydrogen in the water and organic matter of coal. Neutrons from a small radioisotope source penetrate the coal, are scattered by hydrogen, and are measured by a thermal neutron detector. The number of thermal neutrons counted can be directly correlated with the moisture content of coal. Design of a moisture meter based on neutron thermalization depends on many variables, any or all of which can affect the sensitivity of the meter. These factors include those related to the nuclear aspect; type and size of neutron flux and source, type of detecting device, and background count; and those related to the coal being tested: rank, particle size, and ash content. A survey was initiated to eliminate the relatively insignificant factors and to ascertain the magnitude of the major effects. Such information was necessary to fully evaluate the technique and to establish design criteria. Coal contains a relatively large amount of hydrogen in the organic coal substance and the water of hy-dration of the shaly material as well as in the moisture. To apply this concept of moisture measurement to coal requires that the organic substance in coal from any one seam of a particular mine be uniform in hydrogen content. The difference in total hydrogen content of wet and dry coal is relatively small, so that a moisture measurement based on this concept requires a measurement between two large numbers to a high degree of precision. Thus, it was necessary to develop a highly precise instrumentation system for continuous measurement and to obtain a physical arrangement permitting measurement of moving coal with a minimum effect from density variation. EXPERIMENT WITH TRAYS OF COAL Tests were conducted with metal trays containing SO to 100 lbs of coal to develop an instrument system of high precision. A scaling system with a maximum instrument error of 0.2% was used to test different types of thermal neutron detectors. The most suitable type of detector was a boron-10-lined proportional counter tube. While this type of detector showed satisfactory stability, extensive testing disclosed a long-term count reduction probably due to some type of deterioration in the detector. However, development of an electronic system using dual detectors eliminated this deterioration as a serious problem. (The second detector would be used to measure a reference drum of dry coal — the difference in count rate between the wet coal and dry reference coal being a direct measure of moisture content.) Table I, column 1, shows typical results with a 1-curie plutonium-beryllium neutron source and a thermal neutron detector beneath a tray of coal and illustrates the precision of measurement. Consecutive measurements (indicated in Table 1, columns 2-5) of thermal neutrons at various times and positions be-

Jan 1, 1968

By R. M. Board

This paper will focus on measurement and control of four main aspects of crushing, namely horsepower, bowl level, mantle position and feed rate, and will discuss related sensors and control techniques, some of them designed specifically for crusher control, that have proven successful and reliable in many installations.

Jan 1, 1982

By John Birkinbine

THE favor with which the members of the Institute received Mr. Fernow's paper upon the use of charbon roux in the manufacture of iron has encouraged me to present this paper, in the hope of having the discussion upon the manufacture and use of the oldest and undoubtedly the best fuel for producing pig iron continued. Owing to the advances made in employing anthracite coal, bituminous coal, or coke, or mixtures of them, we are apt to forget how much of our present development is due to the pioneers in iron manufacture and the fuel which they employed in the production of pig iron. In Mr. Swank's last compilation of the iron and steel works of the United States, the furnace capacity of the country is given as 5,868,000 tons, of which 1,000,000 tons can be made in the 264 charcoal furnaces. In other words, over one-third of the furnaces now in existence use charcoal for fuel, and produce more than one-sixth of the iron made. If to this is added the 130,000 tons of blooms and billets turned out by the 122 forges and bloomaries, the importance of the charcoal industries will be appreciated.

Jan 1, 1879

By L. A. Panek

Research on roof bolting has developed significant information with respect to the functions that can be performed by properly installed bolts and the methods that can be used to ensure that effective installation has been achieved. The present paper brings together results that are pertinent to the design of a bolting system for reinforcing horizontally stratified mine roof with vertical bolts. The design approach is based on the use of bolts to decrease the maximum bending stress within an arbitrary sequence of roof strata (see Fig. 2) in which the only loads are the weights of the individual beds. The use of rock bolts to achieve other objectives, such as to stabilize a fractured rock mass on the periphery of a mine opening,3 is excluded from consideration herein. Reinforcing effect of bolts consists of a friction effect and a suspension effect in combination. "Friction effect" refers to reduction of bending in a stratified roof due to clamping action of tensioned bolts, which compress the strata, thereby creating frictional resistance to displacement along planes of stratification. (The flexure of a sequence of strata is necessarily accompanied by horizontal displacement of each bed with respect to its neighbor, along mutual surfaces of contact.) Although the sliding of the beds tends to exert a shearing effect on the bolts, tests show that this has negligible influence on the bending stresses, probably because the bolts are so far apart. "Suspension effect" refers to the transfer of part of the weight of the weaker or thinner strata to one or more thick strata, which occurs when strata with differing tendencies to deflect are constrained to have equal deflection. The term "suspension" is used irrespective of whether the thin strata are above or below the thick strata, because tests show that the supporting effect of the flexurally more rigid roof strata is for practical purposes independent of their position in a bolted sequence of strata. An earlier paper4 dealt with a bolted unit in which all strata had equal flexural rigidity; bolting could develop a friction effect but no suspension effect. The present paper deals primarily with a bolted unit in which all strata do not have equal flexural rigidity, so that bolting can develop both a friction effect and a suspension effect. The reinforcing effect of the bolts was determined by a combination of experimental and theoretical stress analysis.4'6'7 The experimental method consisted of loading a model by rotating it in a centrifuge to simulate the gravity forces exerted about an underground excavation. Models were made from two different limestones, although the results are independent of the material because the elastic constants were taken into account in the data analysis. Electric resistance strain gages were bonded to the highest and lowest members of the bolted unit to determine the outer-fiber bending strains at the center and at the supports. The quantitative results presented herein are based on tests of 56 different models, which included a range of values for the structural parameters. Each model was tested several times, with different combinations of spacing and tension of the bolts. DESIGN EQUATIONS The effects of friction and suspension on the flexure of a bolted stratified roof can be expressed by the following equations, which give the maximum bending stress, the deflection, the friction effect, the suspension effect and the transferred load for any (the i-th) member of the bolted unit in terms of the structural parameters:

Jan 1, 1964