Search Documents

By C. W. Dunham

FROM the primary gyratory crushing plant, described in MacLeod's article, ore is delivered to a large storage or surge bin from which it is carried by two transverse conveyors to the secondary crushing plant. The bin has a useful drawoff of about 13,000 tons, this being slightly over one half of the initial daily capacity of the Morenci Reduction Works. This arrangement provides sufficient storage to permit intermittent operation of the primary and secondary crushing plants without too close a coordination between the two.

Jan 1, 1942

TO THE BOARD OF DIRECTORS AND MEMBERS Of THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN Submitted herewith are the reports of the Treasurer for the year 1947 and the reports of the following standing committees Membership, Admissions, Papers and Publications, MINING AND METALLURGY (Magazine), and Library 75th Anniversary Celebration The founding of the Institute at Wilkes-Barre, Pa, in 1871, vas appropriately commemorated by a three-day Celebration, March 17, 18 and 19, 1947, at The Waldorf-Astoria, in New York City The Celebration had been scheduled for the preceding September but had been postponed, perforce, because of conflict with meetings of the Assembly of the United Nations The Celebration immediately preceded the Annual Meeting which was deferred from the usual February dates The proceedings took the form of a "World Conference on Mineral Resources " More than three thousand people, including eight hundred ladies, participated in the proceedings in one way or another Twenty-eight foreign countries were represented, some of them by five or six individual delegates Likewise, official representatives were designated by fifty institutions of higher learning in the United States A special 820-page Anniversary Volume entitled "Seventy-five Years. of Progress in the Mineral Industry,".(which

Jan 1, 1952

By Charles H. Jacoby, Leo E. Read

IN diamond coring salt beds to evaluate deposits, special techniques are applied to standard slim hole drilling to obtain a representative sample of the water soluble sodium chloride. Industrial consumers generally require a run-of-the-mine material of 98.0 pct sodium chloride. Since no commercial beneficiation has yet been devised to upgrade the lower quality salt beds, the only processing is crushing and screening to the size required by the customer. Coring salt sections has recently become important not only in dry mining, but also in the development of brine cavities by hydraulic fracturing and the formation of jugs for storing liquid petroleum products. Drilling Fluid: The fluid used in coring salt beds in New York, Ohio, and Michigan is a thoroughly saturated brine made from 3.0 lb rock salt per gal of make-up water. This mined rock salt, -4 mesh +10 mesh, is dissolved in a lixator, a double-bottomed cone hopper that turns fresh water to fully saturated brine.

Jan 5, 1957

By G. J. Cardwell

The rock and mineral analyst will be called upon to determine both the major and minor constituents in materials as varied as rocks, soil, sediments, concentrates and various liquids. These analyses will have interactions requiring extraction, matrix modification, and background correction. Analytical methodologies include classical gravimetric methods, such as fire assay, emission spectroscopy, X-ray fluorescence, atomic absorption, inductively coupled plasma, and neutron activation. With these capabilities the analyst can be called on to determine three-fourths of the elements in the periodic table. How can the earth scientist pick the method best suited for his particular sample?

Jan 1, 1984

By T. R. Braithwaite

The brief comments made in this chapter deal mainly with shaft sinking, but don't assume that freezing techniques apply only to shaft sinking. They can be used on tunnel work, on such things as liquid gas storage in sediment, and I think you will probably see other applications for it as we go along. The method was first developed in 1883 and was used to sink shallow shafts through water-bearing overburden in Germany and in England. One of the early shafts was in Germany and was sunk by freezing to 310-ft depth. The project required 17 months for drilling, roughly 5 1/2 months for freezing, and another 7 months for sinking, giving an average progress of 10 ½ fpm. Fortunately there have been numerous improvements and new developments in this technique through the years. With equipment and techniques available today, we can take a 20-ft-diam shaft down through 2000 ft of water-saturated overburden and the time schedule runs roughly 4 months for site preparation, freeze-hole drilling, installing the casings, and setting up the plant; 4 ½ months for freezing; and 6 months for excavating and installing permanent linings. This gives a progress rate of about 140 fpm, on average. I might qualify that a little in that the special linings that are required for some formations can affect the time. If it's straightforward sinking where one can use a heavy concrete lining, up to 630-640 fpm may be achieved in a shaft; but with special cast-iron tubbing or types like that, 5 fpd is pretty good progress, so the lining does affect the time. The freezing method is used mainly for sinking shafts through unstable water-bearing formations which cannot be grouted either effectively or economically and which are too deep to enclose in pile casing. Even with overburden, grouting methods available today can handle roughly 100 lb water pressure; in the range of, say, 100 to 150 ft from the surface, it's very often best to grout 40 or 50 ft. You normally drive a pile casing and go through it. Below that range, freezing is very often the economical

Jan 1, 1970

By J. M. Seeman, R. A. Dodd

If some solution-quenched supersaturated aluminum solid solutions, e.g.., Al(Cu), are plastically deformed at room temperature and then aged at 200oC, the hardness may first decrease before increasing in the usual manner ' A similar transient softening is observed, even in the absence of plastic deformation, when a thin foil or small-diameter wire Al(Cu) specimen is rapidly quenched from the solution-treatment temperature and then aged.' Also, some solution-quenched and neutron-irradiated alloys undergo an initial hardness decrease during subsequent aging.3 The usual explanation of the transient softening in the above examples involves the effect of vacancies introduced by plastic deformation, rapid quenching, and neutron irradiation, respectively However, the mechanism of softening is not unequivo-cably established. In the first-noted case, Gane and parkins' observed that the softening was approximately proportional to the difference in the atomic diameters of solute and solvent, and it was argued that, if a large relative difference in atomic diameter promoted vacancy-assisted room-temperature solute diffusion to dislocations, dislocation climb occurring during subsequent aging at 200°C could cause transient softening. Some substantiation of this theory was offered by the additional observation that discontinuous yielding of solution-quenched polycrystalline Al(Cu) tensile specimens was suppressed by interrupting the test for a short aging treatment at 200°C. Of course, reversion (resolution of GPI) at 200°C would also cause softening, and Sil-cock4 expressed the opinion that the softening in the case of Al(Cu) must be partly associated with reversion. Also, Hirsch5 commented on the possibility that, if jogs cause hardening, an anneal at 200°C should straighten the jogged dislocations and result in softening. However, parkins' has re-expressed his belief that these mechanisms are not entirely consistent with the observed serrated stress-strain curves. Experimental. New data has now been obtained for Al(Cu), Al(Ge), Al(Mg), and Al(Zn) primary solid-solution alloys. These alloys were prepared from metals exceeding 99.99 pct purity, and specimens 4 by 4 in. diam were solution-treated, quenched, deformed 10 pct in compression at room temperature, and aged at 200'C in a cottonseed oil bath for various times. Generally, these operations could not be carried out in rapid succession, so the alloys were stored in a freezer between treatments to minimize aging. The variation in hardness with aging time, Figs. 1 to 4, was determined by microhardness testing with a 3.0-kg load. At least five readings were averaged to obtain each data point, and all measurements were taken about the center circumference of each cylinder (region of maximum deformation). Each specimen was used to obtain only one data point, i.e., specimens were not replaced in the aging bath after measurements were made. In

Jan 1, 1968

By Frank Hall

THE needs of the World War showed the necessity of a metal stronger than cast iron which would supplement the supply of steel. So patriotic metallurgists were spurred to new efforts to improve the status of that half-breed of the metal world that had been, more or less erroneously, christened semisteel. As a result, it was developed that for certain purposes semisteel was superior to steel in the manufacture of shells. Steel, because of its greater strength and toughness, is able to carry a greater charge of explosive, weight for weight; consequently, a steel shell can be expected to cause greater destruction when used against fortifications or other inanimate objects, while semisteel, because of its comparative brittleness and its resulting greater fragmentation, is capable of inflicting more serious loss of life when used against opposing forces of men. Therefore, each has its proper place in the economy of war. For the present purpose, steel may be defined as a comparatively pure iron whose physical nature is modified by small amounts of carbon, silicon, sulfur, phosphorus, manganese, and possibly other rarer elements; while cast iron generally is limited to approximately 93 per cent. of iron, the remainder consisting of larger percentages of carbon, silicon, sulfur, phosphorus, and manganese. Semisteel may be defined as cast iron in which the carbon and silicon have been reduced to as low a point as is consistent with maintaining the nature of gray iron, and in which the remaining elements are manipulated so as to give the greatest strength.

Jan 1, 1920

By Thomas A. Hendricks

The object of this paper is to give a brief description of the coals in the different districts of Arkansas and Oklahoma, their present commercial classification, and the need for a scientific classification that shall be more nearly in accord with their physical and chemical properties and shall place them in their proper position in a general scheme of classification. The paper is based on two seasons of field work in the Oklahoma coal field in 1930 and 1931 and on several weeks spent in visiting most of the operating mines in Arkansas in the same years. Most of the productive districts of the Arkansas-Oklahoma coal field lie in an east-west trending belt immediately north of the Ouachita Mountains, but the northwestern districts in Oklahoma trend northward toward Kansas. With the exception of the Muskogee district, where very little coal has been mined, the coal beds of the last-mentioned districts are all younger than those of the districts in the east-west trending belt. Description of the Coal by Districts Lehigh District, Oklahoma (5).1—In the Lehigh district mining has been extensive, but only three or four mines are operating at the present time. Two coal beds of workable thickness, Atoka and Lehigh, are known in this field. The greater part of the mining has been in the Lehigh, or younger bed, and all analyses available for the field have been of that coal. The Lehigh coal is very tough and blocky, the moisture and ash contents are fairly high, 6.5 and 10.7 per cent respectively, the volatile content is 39.5 per cent, fixed carbon 43.4 per cent, B.t.u. value 11,525, and the fuel ratio 1.1 (average 15 analyses). So far as the writer has been able to ascertain, laboratory attempts to coke this coal have been unsuccessful and no attempt has been made to produce coke commercially. Tulsa District, Oklahoma (l).—All commercial mining in the Tulsa district has been by stripping from the Dawson bed, and production has never been very great. The coal is blocky, contains 6.5 per cent moisture, 36.8 per cent volatile matter, 48.4 per cent fixed carbon, and 8.3 per cent

Jan 1, 1932

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 ?ABBÉ, MAX F., Prest., Abbé Engineering Co, 220 Broadway, New York, N.Y. '07 ? ABBÉ, PAULO., Secy.,Abbé Engineering Co., 220 Broadway, New York, N.Y. '07 *ABBOTT, AI ARTHUR Morococlia, Peru, So. America. '95 *ABBOTT, CLARENCE Chief EDgr., Iron Mines, Dic Tennessee Caol, Iron & R. R. Co., Bessemer, Ala. '04 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94 *ABE, MASAYOSHI, Prof. of Mining, Imperial University Kyoto, Japan. '05 ? ACKER, E. O'C., Supt., Treatment Dept., Bethlehem Steel Co., So. Bethlehem, Pa. '86

Jan 1, 1910

By James A. Barr

[CONTENTS PAGE Foreword. By JAMES A. BARRI A New Core Barrel for Prospecting for Phosphate in Florida. By I. M. LEBARON 2 Prospecting for Phosphate in Tennessee. By W. F. GUENTHER 6 Machine Prospecting in Tennessee Brown Phosphate. By H. O. PICKARD, JR8 Diamond Drilling through Flint Horizons in Tennessee. By HENDON R. JOHNSTON9] Foreword PROSPECTING methods used in Tennessee have gradually improved with the years, as required by depletion of the easily accessible and shallow deposits and the universal trend toward mechanization, and as necessitated by exploring deeper beds, often occurring under limestone and flinty overburden. In the early days it was a very simple matter to dig pits by hand, using a plentiful supply of local farm labor to expose relatively shallow deposits of "brown rock" under shallow clayey overburden that would stand up without timbering. Visual inspection of the exposed phosphate and expert judgment of the"grade" analysis, aided by a "biting" test to reveal presence of unwanted silica, furnished most of the information required. All this might be helped by a few samples sent to the local chemist[t] who supplemented his income by judicious trading or tanning a few bear skins. The extra curricula activities did not affect the accuracy of the analysis which hold up even under present day standards. Some shot and core drilling was done in Hickman County, mostly for the limestone-like blue Phosphate deposits. The next step was the use of a 4-in. posthole auger, hand operated as described by Guenther, followed by- a completely mechanized rig, as described by Pickard. Both these methods are practically adapted to the prospecting of the relatively soft brown rock deposits at moderate depths of clay overburden. For prospecting in areas of deeper overburden, such as are often found in Hickman County, up to 150 or even 200-ft depths, a modified core-drilling method is described by Guenther. Johnston describes a special diamond-drilling technique, developed by TVA, to penetrate flint horizons, which was adopted by the International Minerals and Chemical Corporation to prospect in Hickman County where deposits had previously been prospected at considerable expense and with difficulty, by Small, temporary, hand-dug shafts.

Jan 1, 1947

By L. R. Grabill

The Bassick mine, located six miles east of Silver Cliff, Colorado, has, ever since its discovery, been noted for peculiar features. Some of these characteristics exist in one or two other mines, while some are entirely unique. Among these peculiarities I have selected the most noticeable for treatment in this paper: First. The methods of deposition of the ores, which is not, as in ordinary veins, in strata or layers parallel to the walls of the fissure. The ores are arranged in concentric layers upon detached and abraded fragments of the walls; each ore in a separate stratum, and always in the same place in the series. Second. The characteristics of the fissure or opening; its shape and dimensions; its contents, or the vein-filling; and its verticality. Third. The peculiar products of the mine. The most noticeable of these products is charcoal, which is occasionally, and at long intervals, found throughout the ore-body, and in the surrounding conglomerate, from the surface down to the present depth, which is something over eight hundred feet. The existence of charcoal here is, as far as I know, the only instance of its discovery in mines of metallic ores. Fourth. Besides the charcoal, there are other products, in themselves not peculiar, whose manner of arrangement and composition are unusual. The mine is situated near the centre of a small rounded hill of eruptive trachytic rock and feldspathic conglomerate. The diameter of the base of this hill varies from 700 to 1200 feet, and its height is 200 feet above the general level. A cliff or outcrop of fine conglomerate is exposed on the southwest side of the hill. On the northeast it joins by an upward slope the fine-grained, hardened feldspathic paste of Mount Tyndall, which rises 600 feet higher, and of which the elevation containing the Bassick mine thus forms an arm. On visiting the mine, one's attention, whether he is a scientist or not, is immediately attracted by the unusual method of arrangement of the ore. It is seen to be disposed in concentric layers around fragments of trachyte. These fragments, of which each one con-

Jan 1, 1883

By J. A. M. van Liempt

Since the discovery of von Laue, that a crystal forms a natural grating for X-rays, our knowledge of the structure of solids has gone forward with rapid strides. This progress is not only of purely scientific interest, but has also yielded direct technological results. One of the most valuable results is the broadening of our knowledge of the structure of pure metals and alloys. To promote these studies it is often desirable to have at our disposal pieces of metal consisting of one single crystal. As is so often the case in the natural sciences, we obtain the best results by making our earliest experiments on pure, simple materials and avoiding unnecessary complications. The Cryogen Laboratory at Leyden followed this method with much success, because the work was done at such low temperatures that the heat movement of the atoms was almost absent. Similarly we can simplify the studies of metals by leaving out of consideration the influence of the grain boundaries and the mutual influence of the crystals by using unicrystalline instead of polycrystal-line metal. Methods of making single crystals have been scientifically studied during the past few years. Some methods were already known in the arts, but these have been improved and new methods have been developed. The methods for making metallic single crystals may be divided into the following groups: A. From the liquid state B. From the gaseous state C. Electrolytically D. By recrystallization in the solid state Method A 1. Tamwmnn's Method1—Tammann succeeded in making bismuth single crystals of a maximum length of 20 cm. by undercooling the molten metal 0.1 to 0.3' G. below its melting point in glass tubes of a maximum

By Stanley L. Lopata, Eric B. Kula

SEVERAL methods are available for determining pole figures by X-ray means.' The earlier film methods have been replaced by techniques in which the intensities are measured by Geiger counters on an X-ray diffractometerZm7. These methods utilize either flat transmission or reflection samples,214°8 cylindrical specimens,3 or spherical specimens.7 A single transmission or reflection sample will not yield information over the complete pole figure. The cylindrical specimens suggested by Nortod and the spherical specimen of Jetter and Borie7 have the advantage of allowing the whole pole figure to be obtained without any corrections to the intensity for absorption, There is a lower limit to the size of sheet which can be conveniently studied, however, and sample preparation can be rather tedious. Probably the most common method today for determining the complete pole figure is that developed by Schulz. A flat reflection sample is used for determining the pole figure from the center out to about 70". Because of the geometry of the system used, little or no correction for absorption or irradiated volume is necessary.4'6 A separate transmission sample is used for the region near the edge of the pole figure. This procedure requires two separate samples, one of which must be a thin carefully-prepared transmission sample. Furthermore, since the reflection and transmission data are in different arbitrary intensity units, a region of overlap must be obtained, and the intensity data from one set of measurements converted to units of the other. These are serious disadvantages of this method, and they point out the need for a simplified procedure. Since the reflection technique can be used for planes whose normals lie up to about 70° from the sample surface normal, it is apparent that a complete pole figure can be obtained by reflection alone if sample surfaces are cut at oblique angles to the rolling plane Specifically, if a rolled sample is cut so that the normal to the surface formed lies equidistant (54" 44') from the rolling plane normal, rolling direction, and transverse direction, then complete information for one quadrant of the pole figure can be obtained by reflection from the surface. Fig. 1 shows this oblique surface, as well as the position of the pole of this surface in the pole figure. When a surface has been cut oblique to the rolling plane, the standard polar stereographic net is inconvenient to use, and it would be more desirable to have the center of the net coincide with the pole of the oblique plane. Fig. 2 shows such a net, where the center has been offset 54' 44' to correspond to a specimen cut as in Fig. 1. This net was in effect obtained by rotating a standard polar stereographic net 54" 44' with the help of a Wulff net. With the experimental setup used. a sample can be cut from plate of 1/2-in. thickness or br Gen- erally thinner sheet is under investigation, and a composite specimen must be used. A convenient procedure has been to bond together, using epoxy resin, sufficient sheets to form a cube. These are clamped in a vise, and when dry, the whole vise is rotated and a flat surface ground at the required angle. The sample is then mounted inside a larger steel ring using Koldmount, the backside ground flat and parallel to the approximate desired thickness. The sample is then polished and etched to remove any effects of cold working during grinding. With this method only one quadrant of the pole figure is obtained. Often pole figures show symmetry around the rolling and transverse directions, and any slight asymmetry is due to scatter. Should the pole figure not be symmetrical, four oblique surfaces, corresponding to the four quadrants of the pole figure, would have to be examined. In most cases there is symmetry at least around the rolling direction, which reduces to two the number of quadrants to be investigated. For many purposes all that is required is an average polefigure for the four quadrants. This canreadilybe obtained with composite specimens of sheet material, where sheets Corresponding to each of the four quadrants can be intermixed. The four quadrants can be obtained by considering sheet in the normal position, and by rotatiolls of 180" around the sheet normal, the rolling direction, and the transverse direction. If desired, the whole thickness of the sheet can be used, yielding an average of the surface and interior textures; or the surface material can be removed from each sheet, resulting in a pole figure for the center alone. Eugene S. Meieran of the Massachusetts Institute of Technology has independently developed the same method. His results, adapted to a pole figure goniometer with a specimen spiraler, will be described in another publication.

Jan 1, 1962

By G. E. Johnson

LEAD SMELTERS AND REFINERS in 1932 were confronted with the problem of adjusting operations and costs to curtailed production and consumption at reduced prices, a problem which has been partially solved at least by improvements in operating technique and increased efficiency. At the Mount Isa properties in Australia, a third blast furnace and additional Dwight-Lloyd sintering machines were installed during the year, designed to increase the production to 6,000 tons of bullion per month. The large proportion of lead carbonate in the ores to be treated has presented metallurgical problems. Of the total lead contained in the concentrates to be smelted, two-thirds is Dresent as carbonates and one-third as sulfides. In the iiitial operations, the resulting Dwight-Lloyd sinter was soft, contained an excessive amount of fines, and was easily fusible. When charged to the blast furnaces it developed accretions in the upper part of the furnace owing to the easily fusible lead carbonates softening and fusing at the top of the charge column. This was remedied by the addition to the sinter feed of diluents of higher melting point, granulated slag and crushed limestone. The sinter feed consists of concentrates, Cottrell dust and wind-box cleanings, totalling 57 per cent of the charge; return sinter fines 15 per cent; granulated slag 23 per cent; and crushed limestone 5 per cent. The sinter produced contains 34 per cent lead and 0.5 per cent sulfur. Experiments indicated that double sintering under these conditions was of no advantage, so the original plan of single sinter treatment was retained.

Jan 1, 1933

By A. A. Gustafson

IN diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport's operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1040. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Freeport Sulphur Co. discharges over the entire circumference, which gives a discharge lip of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole. The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

By R. S. Shoemaker

Mines are closed for two reasons; exhaustion of ore or insufficient price for the mineral. On the other hand, the reopening of an old mine can be the result of any one of three events; the discovery of more ore, a sudden rise in the price of the product or the use of a new low-cost method of mining or milling the ore. Examples of the latter would be the open-pitting of an orebody previously mined underground as recently happened at Tyrone, N.M., or the adoption of acid leaching of an old pit as has been done at Miami, Ariz. The unique native copper mines of the Keweenaw Peninsula of upper Michigan have not been so fortunate. These deposits, which were first worked by prehistoric Indians, have been mined continuously from the early 1840's to 1968 when the last mines of Calumet and Hecla were closed and the Ahmeek mill. still using eight Nordberg steam stamps, was shut down. There are two types of deposits from which native copper is obtained; amygdaloid, which is a lava flow, and conglomerate, a sedimentary deposit of sand, rock fragments and pebbles cemented together. "In the amygdaloid, the copper is disseminated, or distributed much like the raisins in a cake; but in the rich Calumet conglomerate, the copper is more like a malleable rope or thread cementing the pebbles together." (C. Harry Benedict. Red Metal: The Calumet and Hecla Story, (Ann Arbor, Michigan, 1952), p. 42.) These deposits produced almost all of the copper used by the North in the Civil War and were substantial contributors to the copper needs of the United States in both World Wars. Some were mined to depths of as much as 9500 ft along the dip of the vein structure and 7500 ft vertically. Few of the mines ever really became worked out, but became uneconomical because of depth, pinching of veins or grades which dropped to about 1%.

Jan 5, 1972

By Gerald V. Jergensen

Does an idea have merit? What does it cost to implement? Can the concept be implemented successfully? The ultimate proof is to try, then see. However, when there are many millions of dollars at stake, blindly building and trying requires considerable courage. Owners and investors in retrospect might choose other less complimentary words. So we might ask, "How might we establish the feasibility of an idea or concept before committing large sums of money to the ultimate test?" From this basic and prudent question, has evolved the engineering concept of the feasibility study. A feasibility study is simply a systematic evaluation of an idea or concept to determine the prospects for success. In a literal sense, a feasibility study considers an idea in terms of its data base, "builds" the idea on paper, "operates" that idea, calculates the cost and benefits, then measures the probable success in terms of some economic, technical or financial standard. Feasibility studies can be quite modest in scope yet provide useful insights as to the viability of an idea. A study might be initiated only to examine the completeness or validity of the metallurgical data base. Another study could be a search for a workable idea or solution to an already-identified possibly troublesome problem. In this latter case, the question, "Will it work?" may be far more important than, "How much will it cost?" Feasibility studies are sometimes global in scope, involving several dozens of specialists and examining an entire "grass roots" mining complex. Other studies may be less ambitious but equally important in examining an expansion proposal or developing new operating techniques. Studies may be commissioned to remove plant bottle-necks, solve maintenance problems and so on. The terms study and feasibility study are used interchangeably in this chapter. They denote a systematic method to examine a proposed concept or idea. DATA BASE Typically, studies are initiated with a minimum amount of specific information and a maximum number of assumptions. As the work proceeds and the data base expands, assumptions are replaced

Jan 1, 1982

By J. A. Berger, G. W. Wiener

Several transition metal nitrides have been prepared and their saturation magnetization determined. On the basis of an atomic model of ferromagnetism involving a consideration of nearest neighbor interactions and the assumption that all atomic moments of the metal point in the same direction, it appears that the nitrogen interacts with d-shell of the transition metal in such a way as to reduce the magnetic moment. THERE is a large class of materials having metallic properties which are formed by a combination of hydrogen, boron, carbon, oxygen, or nitrogen with the transition metals. Several attempts have been made to establish the type of metal-nonmetal bonding in these interstitial alloys because it is believed that many of the physical properties of these materials are determined by the characteristics of this bond. Several of these alloys are ferromagnetic, and thus a powerful method is available for investigating the structures in a direct manner by measuring the saturation magnetization. The latter is a fundamental property of ferromagnetic metals and alloys which depends primarily on the electron distribution surrounding the atom. For the first row of transition metals, this refers specifically to the 3 d-shell. Since bonding involves the electronic configuration between atoms, there is reason to suppose that a relationship exists between ferromagnetism and bond type. In the case of the interstitial structures studied in this work, bonding will refer to the distribution of electrons between the transition metal and the nonmetal. Since these alloys have metallic properties, it is further proposed that any bonding interactions will involve the outer p-shell of the interstitial element and the incomplete d-shell of the transition metal. If this is the case, then the relationship between ferromagnetism and metal-non-metal bonding is established qualitatively. In order to investigate the subject quantitatively, certain transition metal nitrides were chosen because they have simple crystal structures, are ordered alloys, and are ferromagnetic. They also have sufficiently high saturation magnetization to be of technical interest. Currently there are two major theories of ferromagnetism, each of which has been applied to the interpretation of the saturation magnetization in terms of atomic structure. They are usually referred to as the band theory and the atomic theory. The former has found widespread application to the study of pure metals and certain solid-solution allays. However, it has not been applied to the interstitial structures or ordered alloys because it does not interpret the properties directly in terms of the crystal structure. The atomic theory on the other hand is especially suited to the study of interstitial structures because it permits an interpretation of ferromagnetic phenomena in terms of the crystal geometry. As has been pointed out previously, the nitrides have simple ordered crystal structures and, therefore, the choice of the atomic theory for the interpretation of the data is a natural one. One of the prime difficulties with the atomistic theory is that its mathematical justification is much more difficult, and for this reason its general acceptance will depend to a large extent on the value it has in explaining and predicting the results of experiment. Before the presentation of the theoretical basis for understanding the metal-nonmetal bond, it is useful to review the ideas existing prior to this work. Four different interpretations have been given to the metal-nonmetal bond. These are summarized as follows: 1—acceptance of electrons by the nonmetal from the incomplete d-shell of the transition metal, 2—transfer of electrons from the nonmetal to the incomplete shell of the transition metal, 3—no exchange of electrons between the two atoms, and 4— a resonating type of bond involving the p electrons of the interstitial atom giving rise to half bonds. Zener'-4 in a recent series of papers has proposed a new theory of ferromagnetism and has developed an explanation of the observed saturation magnetization of iron nitride (Fe,N) using the concept that nitrogen accepts electrons from the 3d-shell of iron. Jack," on the basis of atom size considerations in iron carbonitrides, has proposed that nitrogen transfers or donates electrons to the inner 3d-shell. He found that the effective size of the carbon atom was less than that of nitrogen and thus suggested that the interstitial atoms give up electrons. Kiessling" has studied the borides of several transition metal atoms and proposed that boron loses one p electron to the transition metal. He postulated that the additional electron added to the metal lattice compensates for the loss in metallic properties which results from the increased metal-metal atom separation. GuillaudT3" has proposed similar arguments from some recent magnetic studies he had made on manganese nitride. However, he did not base his conclusions on a quantitative argument. Pauling," in a recent paper, discussed electron transfer in in-termetallic compounds. He classified nitrogen as a hyperelectronic atom which can increase its valence by giving up electrons. He classified the transition metals as buffer atoms which are capable of either accepting or giving UP an electron. He pointed out that two factors are operating which promote electron transfer because they lead to increased stability. The first is an increase in the number of bonds, and the second is a decrease in the electric charges on the atoms. These ideas when applied to the interstitial nitrides would indicate a viewpoint favoring electron transfer by nitrogen to the transition metal. Hagg7s arguments in favor of no exchange are adequately summarized by Wells." Implicitly, Hagg

Jan 1, 1956

By Merrill F. McCarty, Robert S. Olson

New organic flocculants of high-molecular weight are replacing lime, glue, and starch in liquid- solid separation. Of these synthetic materials, polyacrylamides are outstanding. Polyacrylamides form a class of compounds varying widely in composition and activity. Separan 2610H, one of the first of these flocculants' released to the mining industry in 1954, is described' as a high- molecular weight polymer of acrylamide with or without a copolymer material and with some replacement of amide by carboxylic groups.

Jan 1, 1959

By J. N. Roberts, K. V. Gow

In a recent review of the field of plastic deforrnation of metal single crystals, Maddin and chenl indicated the need for systematic investigations of the crystallography of the slip process with special attention to: a) The effect of the orientation of a crystal on the appearance of slip lines, b) The effect of high temperatures on the slip systems of aluminum, c) The effect of strain rate on the crystallography of slip. The present paper deals with the effect of temperature and strain rate on the mechanism of deformation of aluminum single crystals similarly oriented for single and duplex slip. The work of several investigators has shown that in aluminum at high temperatures other slip systems in addition to the predicted {I l l) <101> may operate. The most generally reported additional systems

Jan 1, 1959