Search Documents

By P. R. Sahm, T. V. Pruss

Mixtures of fine GaSb and Gds as well as preal-loyed GaSbl,As, powders were hot-pressed at 690°C and 25,000 psi. Dense alloys with compositional gradients of less than 5 pct were obtained from mixtures containing about 20 mol pct GaAs. For x < 0.2, there were increasing compositional gradients, and for x > 0.2 a GaAs-rich second phase appeared in the microstructure. Densification as well as alloying wlechanisms were enhanced by dissociation and, possibly, oxidation reactions of the powders. Densification of coarse prealloyed material, however, primarily depended on plastic flow phenomena and required temperatures just below solidus and pressures of 50,000 psi Thermal and electrical properties were measured. Although in no case was the figure of merit of melt growth materials approached closer than to within 25 pct, the better overall thermoelectric properties were found in coarse-grained, prealloyed materzals which had been compacted to near theoretical density and where grain regrowth had been induced. Similar results are believed to hold in other binary 111-V compound systems if processed under similar conditions. The densification of unalloyed GaSb powders during pressure sintering (= hot pressing) was shown to depend strongly on powder particle size.&apos; Fine powders displayed a "liquid skin effect" that enhanced compaction through the presence of liquid gallium, whereas coarse powders compacted predominantly by plastic flow. The liquid skin effect, in particular, appeared attractive for alloying GaSb with other, higher-melting, III-V compounds, and to densify these in a one-step operation. This is of special interest in the case of III-V compound alloys as the conventional techniques of melt growth or long-time annealing of powders2 is very time-consuming, especially in cases where a large separation of liquidus and solidus can be expected, such as in GaSbl alloys.2 It was felt that experimentation with this system, a particularly unfavorable example, would allow us to extrapolate to several other, more favorable, cases. Uses of Ill-V alloys are most evident in thermoelectric energy conversion devices.&apos; For this reason certain thermal and electrical properties were measured and compared to those of melt-grown material and to hot-pressed prealloyed powders. EXPERIMENTAL PROCEDURE The pressure-sintering apparatus has been previously described.&apos; Using this equipment, both powder mixtures of GaSb with GaAs and prealloyed GaSbl-,As, powders were hot-pressed. The mixtures were pre- pared from cast GaSb and melt-grown GaAs. The prealloyed material was obtained from stoichiometric melts, initially heated to 1200°C in an evacuated quartz ampoule, and then annealed in the solidus-liquidus interval. A typical annealing cycle consisted of a heating to 850°C (1 hr), extended successive annealing at 750°C (65 hr), and slow stepwise cooling (25 hr) to below solidus. The GaSb, GaAs, and GaSbl-,As, materials were ground in a vibrational mill to particle sizes below 500 . A jet mill reduced these further where necessary. Fine powders were analyzed by Coulter counting for their size distribution. Average sizes by volume were calculated from the data. Mixing of the powders, where necessary, was carried out through rapid vibrational motion. The hot-pressing operation consisted of a degassing period of 15 hr, in most cases at 690°C, followed by several hours of compression, normally 25,000 psi at 690°C for powder mixtures and 50,000 psi at 710°C for prealloyed powders. The chemical compositions were confirmed by X-ray fluorescence analysis. To estimate the degree of solid solution achieved, lattice parameters were determined and interpreted according to Vegard&apos;s rule. In addition, optical microscopy helped to correlate the relative amounts of the phases present as well as the degree of porosity to the measured density. To reveal grain boundaries, polished surfaces were etched4 with H 2 O:H 2 O:HCl = 2:l:l. In several cases microscopic concentration gradients were monitored by electron-probe analysis-. RESULTS AND DISCUSSION Alloying and Densification of GaSn-GaAs Powder Mixtures. After preliminary experiments showed that no appreciable alloying took place in mixtures of coarse GaSb (22.5 p) and fine GaAs (2.5 p) powders, hot pressing of mixtures was confined to fine powders only (3.1 and 2.4 p, respectively). Alloying and densification apparently occurred simultaneously with a grain regrowth mechanism which depended on the presence of a liquid phase.&apos; The liquid phase was provided by the dissociation of GasbS particles into liquid gallium and antimony above 555°C. This not only enhanced grain regrowth and densification, as in unalloyed GaSb,&apos; but took on additional importance here for the alloying process. Alloying was speeded up by the resulting liquid-solid interaction as compared to the very slow solid-state diffusion process normally expected at these temperatures.&apos; The results obtained with a series of powder mixtures have been compiled in Table I. It is seen that for mixtures with less than 20 mol pct GaAs, x < 0.2, the compositional ranges increased and for x > 0.2 a GaAs-rich phase and free antimony appeared in the microstructure in sizable amounts.

Jan 1, 1968

New Jersey Zinc Co. - The Plants Canon City Palmerton Depue

Jan 12, 1953

By Robert G. Woolery, S. Ramachandran, James A. Weber, Donald J. Hansen

Union Carbide began looking seriously at heap leaching in 1971. At that time some 1.6 million tons of mineral averaging 0.40 kg U3O8 /t) (0.80 lb U3O8) were stockpiled at various sites around the Gas Hills, Wyoming, uranium facility. Several alternatives for economically exploiting these reserves were considered and heap leaching seemed the most attractive. At the time, Western Nuclear Inc. was operating a heap leaching project nearby in which the low-grade ore was leached with sulfuric acid, the product liquor treated in an on site solvent extraction circuit, and the stripped product liquor re-acidified and recycled. The operators were most generous in allowing us to visit their site and in answering our questions. They were also helpful in discussing the problems associated with heap leaching. Their experience confirmed our belief that it was possible to operate a heap leach profitably on material too low grade for conventional milling. Based largely on what we had learned from Western Nuclear&apos;s experience, we undertook a program involving a laboratory study to determine the characteristics of the mineral stockpiles, as related to heap leaching, and to conduct a pilot heap leach adjoining our Gas Hill mill. Basically the pilot heap construction and leach procedure were similar to those described in the literature l, 2 with certain modifications to permit detailed monitoring of the operation. In May 1972, the decision was made to construct a test heap. The UCC plant at Gas Hills, Wyoming was selected as the most appropriate site for the following reasons: (1) The necessary equipment for heap construction was readily available. (2) Stockpiles of mineral from the various mining sites were on hand: (3) Construction of the heap could be made on an abandoned tailings pile minimizing problems associated with environmental approval. (4) Proximity of the mill would allow product streams to be absorbed into existing circuits. (5) Necessary utilities were available. (6) Tailings water from the existing circuit could be used for leaching. A program for the pilot heap leach was developed with the following primary objectives. (1) To confirm the data obtained in bench-scale tests particularly on uranium recovery, acid usage, and ore permeability. (2) To evaluate plastic liners used for base preparation. (3) To investigate heap configuration variables. (4) To determine heap leach amenability of the different mineral sources. (5) To establish the economics of heap leaching low-grade ores.

Jan 1, 1979

The opening session was held on Tuesday evening, June 28th. Mr. F. S. Witherbee, of Port Henry, a member of the Local Committee, welcomed the Institute as follows: Mr. President and Gentlemen and (if I my also add) Ladies of the Institute: In the absence of the Chairman of our Local Committee it is my pleasant duty to give you a cordial welcome once more to the shores of Lake Champlain. I think some fourteen years have passed by since we last had the pleasure of receiving you at a meeting in this vicinity ; but the pleasure of that meeting still lingers in our memory; and the profit which we derived from your discussions and from your presence with us has made us heartily desirous to have you here again. If the truth must be known, we were for a time much embarrassed by the difficulty of providing adeqriate and comfortable shelter for the large number of friends whom we hoped (and, as this assembly indicates, had good reason for hoping) to receive. But the liberality and zealous co-operation of the Delaware & Hudson Canal Company and its hotel manager, in offering to open Hotel Champlain, at no little inconvenience, before the usual time, presented a solution of this difficulty, provided the date originally proposed for the meeting could be changed to a week later. This change was duly authorized; .and I think you will all agree with us that it was wise.. At all events, I am sure, I now need offer no apologies for the roof which covers yau. During the fourteen years which have elapsed since your last visit to us, great strides have been made in the industrial development of this country. The meetings of the Institute, held from one end of the land to the other, have permitted you to witness the transformation of small hamlets? like Birmingham, Ala., into populous and thriving industrial centers. You have seen the Minnesota and the

Jan 1, 1893

INDEX TO TRANSACTIONS After a delay of many months, which is very much regretted, but which, it is hoped, will be one means of insuring a volume of accuracy where accuracy is very important, the Institute now has for distribution copies of the index of Volumes XXXVI to LV, inclusive. This is more than a mere index off names of authors and titles of papers. Every important topic under consideration by author or discusser is introduced under such key-word as will enable an engineer to locate the desired information with the minimum expenditure of time. This index sells for $5* in half morocco binding and $4*. in paper covers. With the index of Volumes II to XXXV (which sells for $5 in half morocco and $4 in paper covers), it forms a complete index of the first fifty-five volumes of the Institute&apos;s Transactions. These collective indexes are very valuable to members of the Institute, enabling them to look up matters in their own library; if they have the volumes to which the indexes refer, they can get the information at once, and, if not, they can readily determine whether or not a visit to a nearby public library is desirable.

Jan 7, 1918

By T. G. Madgwick, A. Beeby Thompson

FoR more than 2500 years, natural gas issues in the Surakhany district of the Apsheron peninsula were the object of pilgrimages by fire worshippere and Hindoos from Burma and India. Even as late as 1890, Hindoo priests conducted ceremonies in a temple at Surakhany, which probably replaced a more ancient one; but later, the visits of the pilgrims were prohibited in order to check the spread of Asiatic diseases in that region. For centuries, limited supplies of oil have been abstracted from shallow excavations in the Caspian oil belt and dispatched into the interior of Asia and elsewhere for medicinal and industrial purposes. Statistics show a yield of 37,400 bbl. in 1863, but only since 1869 has there been serious development; in that year the yield was 203,000 bbl. At that time, hand digging was supplanted by drilling, and the enormous wells that resulted from tapping sources hitherto beyond the reach of operators completely demoralized the industry for a time, owing to inadequate outlets for the products. The early activities in this area were greatly hindered by annoying taxation, monopolies, imperial land grants, etc., but when these were revoked or adjusted, in 1877, the industry sprang into prominence and, between 1898 and 1901, the Baku fields produced practically one-half of the world&apos;s supply of oil. Within a few miles of Baku lie the two richest oil fields in the world; viz., the Balakhany-Saboontchy-Romany and the Bibi-Eibat, the latter constituting almost a suburb of the city. For many years the gasoline obtained in the refineries of the Baku area was burned in pits, being considered an undesirable product, and until 1870 the residue also was destroyed, its value as a fuel not being recognized. Kerosene was the main product sought by the refiners. It was shipped across the Caspian Sea and up the Volga to the industrial centers of Russia. Only on the completion of the Baku-Batoum railway did the Baku oil fields secure important commercial communication with the outside world through the medium of the Black Sea. The first tank steamer was successfully launched on the Caspian in 1879, by Messrs. Nobels, for transporting oil in bulk instead of in barrels. In 1905, an 8-in. pipe line to Batoum was completed; this was capable of transporting to seaboard 8,000,000 bbl. of kerosene per annum.

Jan 1, 1921

By Marius R. Campbell

Does mine-sampling show the commercial value of a coal, and if so, how should it be done ? This question is often asked, but seldom answered. During the past summer, while engaged in securing coal for the Government coal-testing plant at St. Louis, I had an excellent opportunity to obtain information on t,his subject, and the results seem to furniih an answer to the question propounded above. Sampling for the U. 8. Geological Survey Coal- Testing Plant. In organizing the work of the testing-plant, it was decided that coal, in car-load lots only, would be accepted for testing; also that this coal should be loaded under the immediate supervision of a representative of the plant, so as to be certain that the car-load sample would be representative. As an additional check on the work, two mine-samples were to be collected from each mine visited, and these samples, as well as the sample from the car when it was received at the testing-plant, were to be carefully analyzed at the chemical laboratory established in connection with the plant and operated under the direction of Prof. N W. Lord of the Ohio State University, Columbus, Ohio. Mine-Samp1ing.—Mine-samples were collected with great care by me and my assistants, Messrs. J. Shober Burrows, John W. Groves and Frank W. De Wolf. The dominant idea in the regulations adopted for mine-sampling mas, that it should be done in such a manner that the sample would have the same composition as the commercial output of the mine.

Jan 1, 1906

By Edward H. Robie, E. J. Jr. Kennedy

his volume records the "clay symposium" that featured the geology side of the Annual Meeting of the Institute at St. Louis, February 19-22, 1951. The symposium consisted of four sessions held under the joint sponsorship of the Geology Subdivision and the Industrial Minerals Division AIME and the Society of Economic Geologists. Its main purpose was to define or outline certain problems of clay and laterite genesis, and the papers herein, which were presented at the first three sessions, deal for the most part with individual deposits or special problems. The fourth session was a seminar concerned almost wholly with a discussion of "problems." The discussion follows the papers in the volume. The clay symposium was not the work of an appointed committee. It was thought up and inspired by John J. Collins, who so ably supervised and co- ordinated the mining, geology, and geophysics program for the 1950 annual meeting of the Institute. After requesting Dr. A. F. Frederickson to get material together on clay and laterites for the St. Louis meeting, Mr. Collins visited Dr. Frederickson and discussed this project with him in greater detail. By that time their interest and enthusiasm had spread to others in the field. The Geology Subdivision, the Industrial Minerals Division, and the Society of Economic Geologists by common consent turned over the organization of the program to Dr. Frederickson. Mr. Collins continued in active touch with Dr. Frederickson and gave him every assistance. Dr. E. C. Harder and Dr. W. D. Keller read all the material comprising the symposium, and their comment was made available to Dr. Frederickson, who did much to put papers and discussion in final shape for publication. To the Karl Eilers Memorial Fund--one of the Funds that enables the Institute to publish books of this kind, to the authors of the various papers, to the contributors to the discussion, and to Messrs. Collins and Frederickson the Institute and readers of this book are indebted.

Jan 1, 1952

By F. M. Lewis, J. F. Myers

The paper reports the development of a large, slow speed ball mill closed circuited with a hvdro-scillator. This increased grinding efficiency 28 pct over conventional units. AS the title indicates, this is a progress report for the first year of experimental operation of a relatively large diameter, slow speed ball mill with 1-in. balls, with and without various classifiers, and including a hydroscillator. Several years ago the authors came to the conclusion that if any further progress were to be made in our flotation process, an understanding of the chemical and physical reactions and the control thereof, in the grinding circuit, was essential. It may be stated, at this point, that the preparation of a correct feed for the flotation process is still the number one objective of our grinding studies. This progress report deals with grinding "per se," and not with the chemical and physical reactions as the result of grinding. Prior to this time we had taken the naive position, that since grinding had been practiced by the industry for some fifty years or more, it had been well exploited and developed by a host of investigators. Consequently, we had given the matter only superficial attention. At the start of our study, we were aware of the fact that some difference in opinion existed, but we were not prepared for the controversial evidence that developed nor for the extent to which the experts differed in their viewpoints. There seemed nothing else to do but to tour the continent and decide for ourselves what was right and what was wrong, read all the published literature and visit with anyone who had ideas about the matter. This we did over the next few ensuing years. Since our study has met with some measure of success, we report, herewith, these data that ultimately they may be of help to other investigators. In 1944 it became necessary to increase our grinding capacity and at the same time to grind the sulphide portion a little finer. This provided the impetus to put our ideas into effect. As has been previously described, our grinding flowsheet at that time consisted of a 6x12 rod mill, followed by two 5x10 ft, and one 6x12 ft trunnion overflow ball mills, with conventional rake classifiers. Naturally, we first considered all the possibilities of altering or adding to the existing equipment. It became evident that if any appreciable increase in grinding efficiency could be obtained, it would pay to scrap the existing small mills and classifiers and install one big mill with adequate classification. Trying to determine just how much more efficient a big mill could be, in which were incorporated all

Jan 1, 1951

By J. F. Myers, F. M. Lewis

The paper reports the development of a large, slow speed ball mill closed circuited with a hvdro-scillator. This increased grinding efficiency 28 pct over conventional units. AS the title indicates, this is a progress report for the first year of experimental operation of a relatively large diameter, slow speed ball mill with 1-in. balls, with and without various classifiers, and including a hydroscillator. Several years ago the authors came to the conclusion that if any further progress were to be made in our flotation process, an understanding of the chemical and physical reactions and the control thereof, in the grinding circuit, was essential. It may be stated, at this point, that the preparation of a correct feed for the flotation process is still the number one objective of our grinding studies. This progress report deals with grinding "per se," and not with the chemical and physical reactions as the result of grinding. Prior to this time we had taken the naive position, that since grinding had been practiced by the industry for some fifty years or more, it had been well exploited and developed by a host of investigators. Consequently, we had given the matter only superficial attention. At the start of our study, we were aware of the fact that some difference in opinion existed, but we were not prepared for the controversial evidence that developed nor for the extent to which the experts differed in their viewpoints. There seemed nothing else to do but to tour the continent and decide for ourselves what was right and what was wrong, read all the published literature and visit with anyone who had ideas about the matter. This we did over the next few ensuing years. Since our study has met with some measure of success, we report, herewith, these data that ultimately they may be of help to other investigators. In 1944 it became necessary to increase our grinding capacity and at the same time to grind the sulphide portion a little finer. This provided the impetus to put our ideas into effect. As has been previously described, our grinding flowsheet at that time consisted of a 6x12 rod mill, followed by two 5x10 ft, and one 6x12 ft trunnion overflow ball mills, with conventional rake classifiers. Naturally, we first considered all the possibilities of altering or adding to the existing equipment. It became evident that if any appreciable increase in grinding efficiency could be obtained, it would pay to scrap the existing small mills and classifiers and install one big mill with adequate classification. Trying to determine just how much more efficient a big mill could be, in which were incorporated all

Jan 1, 1951

Jan 1, 1940

Jan 1, 1941

Jan 1, 1940

By John Henry Harden

IN 1874, with Mr. H. Y. Attrill, of Baltimore, Md., I made an examination of some property at Goderich with reference to sinking for and mining salt. With this end in view we visited all the wells in the neighborhood, but the information sought being of so unreliable a character I advised the putting down of a borehole on the property. This has since been done, the result of which has lately been published by Dr. T. Sterry Hunt in the Toronto Globe. From this there appears to have been passed through six beds of salt of an aggregate thickness of 123 feet. Rock-salt was known to exist, for, by the boring of existing wells, small crystals had been brought to the surface in the dirt, but no attempt had before been made to obtain a reliable sample or to prove the number and thickness of the beds. The question now remaining for discussion is, shall the present method of obtaining the salt be continued, or shall the beds be won by a shaft in a regular mining fashion, by which means the salt may be gotten in a condition almost ready for the market? The present mode of obtaining salt is by boreholes from 6 inches to 8 inches in diameter drilled to the beds, into which is inserted a pump. The "feeders" of fresh water intersected in drilling the well are allowed to descend on the outside of the pump-tube to the salt beds and there become saturated, when, on use of the pump, brine is obtained for evaporation. In the beginning brine can only be had in limited quantity, but by the daily application of the pump, and the gradual solution of the salt, a larger surface becomes exposed to the action of the fresh water, and a continuous supply of brine is obtained. It will then be understood that the supply of brine is dependent upon the feeders of fresh water intersected in boring the well, which, we are told, have never shown any sign of diminution, and this is the water that must be encountered in sinking a shaft. There are ten wells in operation at Goderich, the most important one to the present project being known as the Hawley Well, located at an elevation a few feet above Lake Huron at the mouth of the river Maitland, at a much lower level and nearer to the proposed shaft than any other well in the district. At this well the feeders

Jan 1, 1877

Jan 1, 1941

In many lines of engineering, much excellent standardization work had been done before the war but the war emphasized its importance and showed most clearly the need of cooperation to prevent the confusion caused by the promulgation of overlapping standards by independent bodies. The American Institute of Mining and Metallurgical Engineers, American Institute of Electrical Engineers, American Society of Civil Engineers, American Society of Mechanical Engineers, and American Society for Testing Materials, recognizing the value of what had been done, invited the Government Departments of War, Navy and Commerce to appoint representatives to act with them to continue this work; the body so formed is the American Engineering Standards Committee. It has required time to definitely formulate its objects and to arrange methods for accomplishing them that would be effective without interfering with the many organizations that have been doing such excellent work in this line. The American Engineering Standards Committee has just completed and adopted a revision of its Constitution, which has been sent to the Governing Boards of all the Departments and Societies represented on the Committee with a request for its ratification. The new Constitution changes the name to American Engineering Standards Association as more fittingly indicating the wide scope of the interests involved. The objects of the association are stated as follows: 1. To unify and simplify the methods. of arriving at engineering standards, to secure cooperation between various organizations and to prevent duplication of standardization work. 2. To promulgate rules for the development and adoption of standards, 3. To receive and pass upon recommendations for standards submitted as provided in the Rules of Procedure, but not to initiate, define, or develop the details of any particular standard. 4. To act as a means of intercommunication between organizations and individuals interested in the problems of standardization. 5. To give an international status to approved American engineering standards. 6. To cooperate with similar organizations in other countries and to promote international standardization.

Jan 7, 1919

By AIME AIME

THE Charleston Section of the A. I. M. E. held a joint meeting with the National Coal Association and the American Society of Mechanical Engineers on May 6 and 7, at which 94 members and guests were registered. Mechanical operation of coal mines was the subject discussed. First on the program was a paper entitled "Rock Dusting in the Coal Mines of West Virginia," by R. M. Lambie, chief of the Department of Mines, and Gordon MacVean. It appears in full in the current issue of MINING AND METALLURGY, p. 290. J. E. Jones of the Old Ben Coal Corp. opened this discussion by describing the method of rock dusting employed in the mines of that company, giving many interesting details, incidentally referring to the use of rock dust in fighting mine fires. He described one case where a number of troughs was brought to within 150 ft. of the fire, and rock dust had been thrown in its direction. After each trough had been thrown the party advanced a few feet, where another trough was discharged. About 10 ft. were gained on each advance, until the party found they had advanced completely over the fire.

Jan 1, 1926

By C. Feng, I. R. Kramer

A study was conducted to determine the influence of the surface on the yield point of fcc metals and high-purity iron. For the high-purity fcc metals, the yield Point produced by restraining a specimen may be eliminated by removing a sufficient amount of the layer. A yield point similar to that in fcc metals was found when iron specimens were pre-strained after a prior deformation. This yield point is not due to an aging effect but is associated with the surface layer. The yield points in age-hardenable aluminum alloy and those connected with "work softening" are not affected by a surface-removal treatment and are, therefore, caused by bulk-type dislocation reactions. The yield point which appears in previously strained fcc metals has been the subject of numerous studies. Several theories have been advanced to explain this "unloading-reloading" yield point. Cottrell and stokes,&apos; from their study on the effect of temperature on plastic properties of high-purity aluminum, considered that it was the result of an avalanche "breakdown" of Lomer-Cottrell sessile dislocations. Haasen and Kelly2 extended this concept of dislocation-dislocation interaction to account for the yield point when unloading and reloading was carried out at the same temperature. On the other hand, strain aging was found to be responsible for the yield point in A1-Mg alloy by Westwood and Broom,3 and in aluminum alloys containing various amounts of alloying elements by Smallman, Williamson, and Ardley.4 In these cases, the yield point is considered to be associated with the locking of dislocations by impurity atoms. Birn-baum and filer5,6 and Takamura and muira7 reported that, when a high-purity copper specimen was prestrained, then held at a lower stress, and finally reloaded at the prestrain temperature, a larger yield point was observed. Such an increase was attributed to the locking of dislocations by point defects. In addition, Bolling8 suggested that both mechanisms, i.e., dislocation-dislocation interaction and strain aging, are responsible for the yield phenomenon, at least in a brass. Thus, there appears to be experimental evidence for both the strain aging and dislocation-dislocation interaction theories to explain the yield point in the fcc metals and alloys. In a previous article,9 one of the authors observed that, if sufficient amounts of metal were electrolti-cally removed after deformation of a high-purity aluminum single crystal, the yield point did not appear upon reloading. Continued pursuit in this area revealed that the effect of the surface on the yield-point phenomenon is not limited to one metal but affects a variety of metals of different lattice structures. Nor is the effect limited to the yield points produced by simple unloading-reloading at constant temperature; the surface exerts an important role on the yield point even when the temperature is changed at some stage during the test. It is the intent of the present article to give additional information regarding the effect of the surface on the yield-point phenomenon and to show the association between the yield point in both fcc and bcc metals and the existence of a heavy concentration of dislocation in the region near the surface of a deformed specimen.10 EXPERIMENTAL Materials. The single crystals used in this study had a nominal cross section of 0.125 by 0.125 in. and a 3-in. gage length and were prepared by a modified Bridgman technique. The initial purity for the metals was 99.997, 99.999, and 99.999 pct for aluminum, copper, and gold, respectively. Bar stock of these same materials was used in the preparation of the polycrystalline specimens of aluminum and copper. The iron specimens were machined from rods of "ferrovac", reported to have a purity of 99.98 pct. In addition, a precipitation-hardening aluminum alloy, containing 1.5 pct Cu, 2.5 pct Mg, and 5.5 pct Zn, was used. The polycrystalline specimens of iron, copper, and the aluminum alloy had a diameter of 0.17 in. and a gage length of 2 in. while the high-purity aluminum specimen had a nominal rec-

Jan 1, 1965

By George W. Maynard

For an account of the discovery and the determination of chromite on Port au Port Bay I am indebted to Mr. Obalski, Government mining engineer for the Province of Quebec. He writes: " In June, 1894, with the authorization of our Government, I went to Newfoundland to examine some asbestos property. Passing through Halifax, I had interviews with some gentlemen who told me that besides the asbestos there was in the same district a big deposit of iron-ore. They handed me some specimens, and, after ascertaining that they were not magnetic, and learning that they were found in serpentine, I said they were chromic iron. I visited the place on June 27, 1894, and confirmed my opinion, pointing out at the same time the importance of the deposit, as appears in my report of July 9, 1894. I do not claim any credit for the discovery of chrome-ore in Newfoundland; but, as a matter of fact. when I came in contact with the Halifax gentlemen they did not appear to know the nature or the value of the mineral until I mentioned to them that it was chromite. "&apos; Mr. Obalski&apos;s report was mainly devoted to the asbestos-deposits. That portion relating to the chromite was as follows: " On the right side of the creek there is a show of chromic iron of good quality, which appears scattered through the serpentine in several places on the face of the cliff for 40 to 50 feet. A few boulders are found farther up at a distance of 100 feet, and also in the ckeek itself. From this point the deposit exists on a relatively large area, the widest exposures being from 6 to 7 feet. Chromic iron deposits in serpentine rock have no regularity, and are merely pockets. In the case of the property in question this rule is not changed, but the pockets look to be of large extent, and could be easily worked." My own preliminary investigation of the property was made

Jan 1, 1898

By F. G. Jaicks

RECOGNITION of the benefits to be gained from the continuous casting of molten steel into finished or semifinished products has been given by scientific minds since the very beginnings of steel plant technology. In fact, Sir Henry Bessemer is credited with the first of a long list of patents&apos; issued by the U. S. Patent Office for a process which would accomplish this desirable end. None of these early ideas attained practical success and, as a result, the conventional method of teeming into ingot molds became an integral part of modern steelmaking operations. This procedure, although refined to keep pace with the changes which have come about in steelmaking and finishing facilities, is recognized to have inherent shortcomings which adversely affect manufacturing costs and steel quality. Interest in the continuous casting of steel persists because the process is directed toward avoiding some obvious weaknesses of conventional ingot casting. It has been recognized that should it be possible to substitute any of the continuous casting techniques under current development for ingot casting, it would no longer be necessary to make large capital investments in primary rolling equipment, the sole purpose of which is to reduce ingot castings to a form rollable on finishing mills. The results reported in the continuous casting of non-ferrous metals and specialty steels indicate that in addition to avoiding the primary rolling mills there is some basis for expecting significant improvements in yield, surface, and internal quality. Recognizing the shortcomings of the conventional procedures, the Inland Steel Co., in cooperation with Atlas Steels Ltd. and the Freyn Dept. of the Kop- pers Co. Inc., embarked upon a program to evaluate certain aspects of continuous casting in order to determine whether the process could be applied practically to an existing integrated steel plant producing &apos;large tonnages of carbon steels. TO assist in this evaluation a study was carried out in which several types of low carbon steel were continuously cast in an existing machine. It is the purpose of this paper to review some of the results obtained in the casting studies and to interpret the information that was obtained so as to indicate factors that must be considered in assessing operating limitations and plant capacities. Despite the early interest in the continuous casting of steel, the actual application to the steel industry is relatively recent. At present, there are about 25 operating plants casting steel, most of which have been built in the past decade. None of these plants could be classified as large in terms of the tonnages that are being processed by the major integrated steel plants. In contrast to the situation in the steel industry, there has been widespread adoption of the continuous process in the casting of nonferrous alloys, particularly aluminum and copper. As a result, much of the basic information that was required to apply the process to steel was developed in the nonferrous industries. In this respect, a most important contribution was the development of the Junghans2 system, which was initially designed for the casting of nonferrous metals and later applied to the casting of steel. Alternative methods for casting have also been proposed by Babcock and Wilcox Tube Co.,&apos;" the British Iron and Steel Research Association,5 and the Gebruder Bohler A. G.13 Each of these methods is now being used successfully for the casting of special steels in small experimental plants or in modest sized commercial steelworks. The Original Junghans process was first developcd in Germany. Further application of the process has been made by Rossi in other countries.&apos;*&apos; The experi-

Jan 1, 1958