Search Documents

By A. L. Hornbaker, S. D. Schwochow

Industrial minerals are becoming increasingly important in Colorado's mining industry, not only in production value but also in the variety available and in their potential development for both conventional and new uses. Fluorspar, building stone, fire clay, and pegmatite minerals have been historically important but are not now extensively mined. Aggregates (sand, gravel, and crushed stone), cement materials, metallurgical limestone, and common clays currently are the highest valued commodities. Those offering the greatest future potential include diamonds, nahcolite and dawsonite associated with oil shale, alunite, potash, zeolites, and rare earths.

Jan 1, 1982

By H. E. Exner

This article is a critical review of the influence of surface preparation on crack formation at Vickers indentations in the test used by Palmqvist3-7 to evaluate the toughness of cemented carbides. Experimental results are presented which clearly show that grinding introduces compressive surface stresses into the cobalt phase and thus reduces the crack length. The deformed surface layer is removed by polishing and a stress pattern is approached corresponding to that in the bulk material. Cracks of maximum length are characteristic of this stress state. Deformation stresses can be removed by annealing above 800°C. On the basis of these results , sample preparation for the crack length test can be simplified, the accuracy of measurement is improved, and a simple and significani parameter is found to describe crack resistance of cemented carbides. FOLLOWING suggestions by Ammann and Hinniiber,1'2 Palmqvist3-7 developed a method for testing the toughness of cemented carbides using as a measure the sum of crack lengths at the four corners of a Vickers hardness indentation. This method has several advantages over the bend test commonly used in carbide technology: a) specially formed samples are unnecessary; b) sufficient information can be obtained from one sample; c) the scatter is relatively small; d) the range of actual values for commercial cutting alloys is wide. Thus, this test is both cheaper and more precise than the bend test. Nevertheless, Palmqvist's method is not widely used, mainly for two reasons: a) The relationship between crack length and the technological properties of the material (wear and shock resistance) is not clear. b) The crack length is strongly dependent on surface treatment. It is necessary, therefore, that surface preparation be very precise and reproducible, conditions usually hard to obtain. While any other simple mechanical test has this first drawback, the second became crucial in the application of the crack length method as a practical test. The reasons that this drawback could not be eliminated are, in our opinion, misleading and inconsistent interpretations of the influence of surface preparation on the crack length given in literature. In the following, after a short review of previous experimental results the interpretations given by different authors,4?'-11 cf. Table I, are discussed critically and a consistent explanation is presented on the basis of which improvements of the method of crack length testing are proposed. 1) PREVIOUS EXPERIMENTAL RESULTS In his first attempt to use the cracks at Vickers impressions as a quantitative measure of the toughness of cemented carbides, palmqvist3 calculated the work necessary to initiate cracks by the formula: Sk =k.Pk. [I] where k = numerical constant = 6.49, Sk = critical work to initiate cracks (gf cm), Pk = critical load (load necessary to initiate cracks) HV = Vickers hardness (kp per sq mm). The difficulties involved in experimental determination of the critical load were overcome by the observation that a linear relation holds between the applied load and the sum of the crack lengths at the four corners of the indentation. This linear function, given by Eq. [2] below, was confirmed by Dawihl and Alt-meyer9and by our experiments, see Fig. 1: I = a1.P +a2 [2] where 1 = sum of the crack lengths at a Vickers indentation, P = applied load, al, a2 = parameters dependent on the toughness of the alloy and the surface preparation. The critical load, Pk, is now given by a2, which can be obtained by extrapolating the load vs crack length line to zero crack length, see Fig. 1. This simple relationship, Eq. [2], led Palmqvist1,7 to a parameter which was more reproducible and easier to obtain experimentally than the critical work: the work, S300, put into the sample to produce an average crack length of 300 µm per indentation. This parameter is calculated using the formula: where the load, P3oo, giving a crack length of 300 µm, can be taken from the load-crack length plot, Fig. 1,

Jan 1, 1970

By T. B. Counselman

Probably the earliest concentration of iron ore in this country was carried on in the northeastern magnetite areas. Magnetic concentration was relatively simple and gave a concentrate that, after agglomeration, and in spite of being high in phosphorus because of the dry concentrating methods then in use, was satisfactory blast-furnace feed. Production from the northeastern magnetite area languished after the discovery and development of the Lake Superior ores, where there was seemingly an unlimited tonnage of high-grade ore, first the Michigan ores, and subsequently the still larger deposits of Minnesota. For years only the higher grade, direct shipping ores of the Lake Superior district were mined. Those of Michigan, and of the Vermilion Range in Minnesota, were hard ores and came principally from underground mines. The softer ores of the Mesabi came partly from underground mines, but mostly from the enormous deposits that could be worked by open-pit methods. The costs of ore from these open-pit deposits, even with the high initial cost of stripping, were so low that the underground mines of the Mesabi could hardly compete. The so-called Old Range ores, of Michigan and of the Vermilion. Range of Minnesota, were hard and lumpy, and opened UP the burden in the blast furnace, therefore making possible harder driving with greater output. Also, some of these ores were of such grade and physical characteristics that they were suitable for charge ore in the open hearth. These ores, therefore, commanded a price premium, and could compete with the softer, finer, but cheaper, Mesabi ores. The big tonnage reserves, however, are on the Mesabi. and it is these big open-pit deposits that constitute our stock pile of iron ore, from which we are drawing so heavily during this war period. On the western end of the Mesabi the ore was found to be high in silica, and not suitable as furnace feed. As early as 1902, attempts were made to concentrate this so-called wash ore and by 1910 the first washing plant was put into operation. The Process was very simple, consisting essentially of a sizing and washing operation, with scalping screens, logwashers, and tables, which later were replaced by classifiers. Ore particles finer than 100 mesh were deliberately wasted, because these fines were undesirable in the furnace. Fortunately, these tailings were impounded, and already are being reworked. Before long some of the low-grade ores began to require more elaborate treatment than the simple washing operation and, tables having been discarded because of their low capacity, in favor of classifiers, jigs were next introduced. These were able to discard coarser pieces of tailing than classifiers. jigs are in active use today, various improvements having been made in their design and application. Various other machines and methods of concentration have been tried from time to time, and have in turn been discarded for more improved processes. The latest and most important process that has been

Jan 1, 1947

By T. B. Counselman

Probably the earliest concentration of iron ore in this country was carried on in the northeastern magnetite areas. Magnetic concentration was relatively simple and gave a concentrate that, after agglomeration, and in spite of being high in phosphorus because of the dry concentrating methods then in use, was satisfactory blast-furnace feed. Production from the northeastern magnetite area languished after the discovery and development of the Lake Superior ores, where there was seemingly an unlimited tonnage of high-grade ore, first the Michigan ores, and subsequently the still larger deposits of Minnesota. For years only the higher grade, direct shipping ores of the Lake Superior district were mined. Those of Michigan, and of the Vermilion Range in Minnesota, were hard ores and came principally from underground mines. The softer ores of the Mesabi came partly from underground mines, but mostly from the enormous deposits that could be worked by open-pit methods. The costs of ore from these open-pit deposits, even with the high initial cost of stripping, were so low that the underground mines of the Mesabi could hardly compete. The so-called Old Range ores, of Michigan and of the Vermilion. Range of Minnesota, were hard and lumpy, and opened UP the burden in the blast furnace, therefore making possible harder driving with greater output. Also, some of these ores were of such grade and physical characteristics that they were suitable for charge ore in the open hearth. These ores, therefore, commanded a price premium, and could compete with the softer, finer, but cheaper, Mesabi ores. The big tonnage reserves, however, are on the Mesabi. and it is these big open-pit deposits that constitute our stock pile of iron ore, from which we are drawing so heavily during this war period. On the western end of the Mesabi the ore was found to be high in silica, and not suitable as furnace feed. As early as 1902, attempts were made to concentrate this so-called wash ore and by 1910 the first washing plant was put into operation. The Process was very simple, consisting essentially of a sizing and washing operation, with scalping screens, logwashers, and tables, which later were replaced by classifiers. Ore particles finer than 100 mesh were deliberately wasted, because these fines were undesirable in the furnace. Fortunately, these tailings were impounded, and already are being reworked. Before long some of the low-grade ores began to require more elaborate treatment than the simple washing operation and, tables having been discarded because of their low capacity, in favor of classifiers, jigs were next introduced. These were able to discard coarser pieces of tailing than classifiers. jigs are in active use today, various improvements having been made in their design and application. Various other machines and methods of concentration have been tried from time to time, and have in turn been discarded for more improved processes. The latest and most important process that has been

Jan 1, 1947

By Wilford Stork

CERTAIN influences of oxygen on iron have been known for many years and it has always been considered one of the worst enemies of the iron and steel founders. Nobody had a good word for it, hence little was done to make use of this oxygen. In all the fields of foundry practice, the desideratum was "melt without oxidation of the metal." In the consideration of the influence of oxygen on cast iron, we must not confuse this condition with oxidized iron caused by poor melting conditions, due to a high bed, heavy charges, low coke ratio, excessive melting rate, high blast, or poor charging. It is admitted that oxygen absorbed by iron melted under these conditions has a deleterious effect on the properties of the iron. The writer has had experience both in the melting under such poor conditions and in remedying these bad conditions and considers the product far inferior to iron melted under normal conditions. As stated by Dr. Richard Moldenke,1 such iron has a higher melting point and high combined carbon, is sluggish, and contains slags and oxides in solution in the liquid, causing slag inclusions and gas occlusions, thus producing defective castings. This oxidized condition cannot be counteracted or removed by any of the known deoxidizers; it can be remedied only by proper melting conditions. Such iron is really burned, whereas the iron considered in this paper was melted under normal conditions with moderate blast, correct bed height, light charges of iron, and low coke consumption and is not in this category at all. In 1914, the late J. E. Johnson, Jr., startled the metallurgists of the world when he published his results on the advantages of oxygen on cast iron.2 His work is so convincing and so logical, in spite of the common and well-established notions on the subject, that nobody has been able to refute a single argument. Such an eminent authority on iron and steel metallurgy as Prof. H. M. Howe has accepted the work in all its details in his latest book3 The work of J. E. Johnson, Jr., has revolutionized

Jan 6, 1919

The State Mining Experiment Station, Missouri School of Mines and Metallurgy, Rolla, Mo Charles H. Fulton, Director of the School of Mines Martin H. Thornberry, Director of the Mining Experiment Station. From the State Mining Experiment Station are issued all the general and technical bulletins of the School of Mines The latest bulletin containing a complete list of publications will be sent upon application to the Director of the Station Residents of the state may obtain bulletins as issued without charge, or may ask to be placed on the mailing list. Nonresidents should write to the Director for further information concerning specific bulletins. From the long list of bulletins the following have been care¬fully selected as being most likely to interest the geologist and the mining engineer. Vol 8, No. 1 (1916), Bibliography of concentrating ores by flotation, by J Cunningham, vol 1, No 3 (1912), Some apparatus and methods for demonstrating rock drilling and the loading of drill holes in tunneling, by L E Young, vol 2, No 1 (1915), Comparative tests of piston drill bits, by C R Forbes and L M Cummings; vol 2, No 3 (1916), Cupellation losses in assaying, by H. T Mann and C. Y Clayton; vol 4, No 1 (1917), The hydrometallurgy and electrolytic precipitation of zinc, by F D. James; vol 4, No 2 (1917), The effect of additional agents in flotation, pt 1, by M. H. Thornberry and H T. Mann, vol 5, No 1 (1919), The carbonization of Missouri cannel coals, by H L. Dunlap, K. K. Kershner and V. X Smiley. Vol 5, No. 4 (1921), Coal mining methods in Missouri, by W W Weigel, vol 6, No 1 (1921), The problem of the St Peter sand¬stone, by C L Dake, 50 cents, vol 6, No. 2 (1922), Bibliography on the electrothermic metallurgy of zinc, by B M. O'Harra, vol 6, No. 4 (1923), Experiments on the distillation of zinc from complex zinc-lead-silver ores, by B M. O'Harra and E S. Wheeler, vol 7, No 3 (1924), Underground loading devices, by C. E. van Barneveld, 81; vol 7, No. 4 (1924), Briquetting of zinc ores, by B. M. O'Harra; vol. 8, No 2 (1925), A treatise of Missouri clays, by M. H. Thornberry.

Jan 1, 1933

By Freeman Bishop

Mercury is the latest ecological disaster. It was believed to be no pollution problem because it is heavier than water and expected to fall to the bottom of streams. But the Food and Drug Administration (FDA) found that mercury in a dozen states and several Canadian provinces was being ingested by fish. A Deadly Dose First to sound the alarm was Canada when a graduate student's research revealed that mercury contamination in Lake St. Clair had reached 1.4 pmm. which is almost three times the 0.5 ppm the FDA's allowable maximum.

Jan 1, 1970

The surface area that mining requires is a minuscule fraction of the total land mass of the United States, according to the US Bureau of Mines' latest report "Land Utilization and Reclamation in the Mining Industry, 1930-71." During the 42-year period from 1930 to 1971, the mining industry utilized 3.65 million acres-only 0.16% of a total 2.27 billion acres of land-and reclaimed 1.46 mil- lion acres, or 40% of what it used. Which leaves, as still unreclaimed, 0.096% of the nation's total land mass.

Jan 10, 1974

By T. B. Counselman

PRobably the earliest concentration of iron ore in this country was carried on in the northeastern magnetite areas. Magnetic concentration was relatively simple and gave a concentrate that, after agglomeration, and in spite of beillg high in phosphorus hecause of the dry concentrating methods then in use, was satisfactory blast-furnace feed. Production from the northeastern magnetitc area languished after the discovery and development of the Lake Superior ores, where there was seemingly an unlimited tonnage of high-grade ore, first the Michigan ores, and subsequently the still larger deposits of Minnesota. For years only the higher grade, direct shipping ores of the Lake superior district were mined. Those of Michigan, and of the Vermilion Range in Minnesota, were hard ores and came principally from underground mines. The softer ores of the Mesabi came partly from underground mincs, but mostly from the enormous deposits that could be worked by open-pit methods. The costs of ore from these open-pit deposits, even with the high initial cost of stripping, were so low that the underground mines of the Mesabi could hardly compete. The so-called Old Range ores, of Michigan and of the Vermilion Range of Minnesota, were hard and lumpy, and opened UP the burden in the blast furnace, therefore making possible harder driving with greater output. Also, some of these Ores were of such grade and physical characteristics that they were suitable for charge ore in the open hearth. These ores, therefore, commanded a price premium. and could compete with the softer, finer, but cheaper, Mesabi ores. The big tonnage reserves, however, are on the Mesabi. and it is these big open-pit deposits that contitue- our stock pile of iron ore, from which we are drawing so heavily during this war period. On the western end of the Mesabi the ore was found to be high in silica, and not suitable as furnace feed. As early as 1902, attempts were made to concentrate this so-called wash ore and by 1910 the first washing plant was put into operation. The Process was very simple, consisting essentially of a sizing and washing operation, with scalping screens, logwashers and tables, which later were replaced by classificrs. Ore particles finer than I00 mesh were deliberately wasted, because these fines were undesirable in the furnace. Fortunately, these tailings were impounded, and already are being reworked. Before long some of the low-grade ores began to require more elaborate treatment than the simple washing operation and, tables having been discarded because of their low capacity, in favor of classifiers, jigs were next introduced. These were able to discard coarser pieces of tailing than classifiers. Jigs are in active use today, various improvements having been made in their design and application. Various other machines and methods of concentration have been tried from time to time, and have in turn been discarded for more improved processes., The latest and most important process that has been 38

Jan 1, 1944

By T. B. Counselman

PRobably the earliest concentration of iron ore in this country was carried on in the northeastern magnetite areas. Magnetic concentration was relatively simple and gave a concentrate that, after agglomeration, and in spite of beillg high in phosphorus hecause of the dry concentrating methods then in use, was satisfactory blast-furnace feed. Production from the northeastern magnetitc area languished after the discovery and development of the Lake Superior ores, where there was seemingly an unlimited tonnage of high-grade ore, first the Michigan ores, and subsequently the still larger deposits of Minnesota. For years only the higher grade, direct shipping ores of the Lake superior district were mined. Those of Michigan, and of the Vermilion Range in Minnesota, were hard ores and came principally from underground mines. The softer ores of the Mesabi came partly from underground mincs, but mostly from the enormous deposits that could be worked by open-pit methods. The costs of ore from these open-pit deposits, even with the high initial cost of stripping, were so low that the underground mines of the Mesabi could hardly compete. The so-called Old Range ores, of Michigan and of the Vermilion Range of Minnesota, were hard and lumpy, and opened UP the burden in the blast furnace, therefore making possible harder driving with greater output. Also, some of these Ores were of such grade and physical characteristics that they were suitable for charge ore in the open hearth. These ores, therefore, commanded a price premium. and could compete with the softer, finer, but cheaper, Mesabi ores. The big tonnage reserves, however, are on the Mesabi. and it is these big open-pit deposits that contitue- our stock pile of iron ore, from which we are drawing so heavily during this war period. On the western end of the Mesabi the ore was found to be high in silica, and not suitable as furnace feed. As early as 1902, attempts were made to concentrate this so-called wash ore and by 1910 the first washing plant was put into operation. The Process was very simple, consisting essentially of a sizing and washing operation, with scalping screens, logwashers and tables, which later were replaced by classificrs. Ore particles finer than I00 mesh were deliberately wasted, because these fines were undesirable in the furnace. Fortunately, these tailings were impounded, and already are being reworked. Before long some of the low-grade ores began to require more elaborate treatment than the simple washing operation and, tables having been discarded because of their low capacity, in favor of classifiers, jigs were next introduced. These were able to discard coarser pieces of tailing than classifiers. Jigs are in active use today, various improvements having been made in their design and application. Various other machines and methods of concentration have been tried from time to time, and have in turn been discarded for more improved processes., The latest and most important process that has been 38

Jan 1, 1944

By T. B. Counselman

PROBABLY the earliest concentration of iron ore in this country was carried on in the northeastern magnetite areas. Magnetic concentration was relatively simple and gave a concentrate that, after agglomeration, and in spite of being high in phosphorus because of the dry concentrating methods then in use, was satisfactory blast-furnace feed. Production from the northeastern magnetite area languished after the discovery and development of the Lake Superior ores, where there was seemingly an unlimited tonnage of high-grade ore, first the Michigan ores, and subsequently the still larger deposits of Minnesota. For years only the higher grade, direct shipping ores of the Lake Superior district were mined. Those of Michigan, and of the Vermilion Range in Minnesota, were hard ores and came principally from underground mines. The softer ores of the Mesabi came partly from underground mines, but mostly from the enormous deposits that could be worked by open-pit methods. The costs of ore from these open-pit deposits, even with the high initial cost of stripping, were so low that the underground mines of the Mesabi could hardly compete. The so-called Old Range ores, of Michigan and of the Vermilion Range of Minnesota, were hard and lumpy, and opened up the burden in the blast furnace, therefore making possible harder driving with greater output. Also, some of these ores were of such grade and physical characteristics that they were suitable for charge ore in the open hearth. These ores, therefore, commanded a price premium, and could compete with the softer, finer, but cheaper, Mesabi ores. The big tonnage reserves, however, are on the Mesabi, and it is these big open-pit deposits that constitute our stock pile of iron ore, from which we are drawing so heavily during this war period. On the western end of the Mesabi the ore was found to be high in silica, and not suitable as furnace feed. As early as 1902, attempts were made to concentrate this so-called wash ore and by 1910 the first washing plant was put into operation. The process was very simple, consisting essentially of a sizing and washing operation, with scalping screens, logwashers, and tables, which later were replaced by classifiers. Ore particles finer than 100 mesh were deliberately wasted, because these fines were undesirable in the furnace. Fortunately, these tailings were impounded, and already are being reworked. Before long some of the low-grade ores began to require more elaborate treatment than the simple washing operation and, tables having been discarded because of their low capacity, in favor of classifiers, jigs were next introduced. These were able to discard coarser pieces of tailing than classifiers. Jigs are in active use today, various improvements having been made in their design and application. Various other machines and methods of concentration have been tried from time to time, and have in turn been discarded for more improved processes. The latest and most important process that has been

Jan 1, 1943

By Frank Woolley, John F. Elliott

The high-temperatzrre solulion calorimeter has been modified and an extension dynamic analysis of i/s transient behavior has provided an improved basis for interpretation of the experimental data. The partial molar heats of mixing, Him, of aluminum, copper, and silicon in the corresponding binary liquid-iron alloys haz,e been measured directly at 1600°C. The resulls in kcal per g-alom are: THE high-temperature1,2 solution calorimeter was planned and designed to obtain directly the partial molar heat of solution of solute elements in a variety of liquid metals that might serve as solvents. Results obtained in the temperature range of 1000° to 1200°C were described in the two earlier publications. However, a long-term goal in the program has been to obtain measurements at 1600°C of the heats of solution of elements in liquid iron. Hence, subsequent to the work last reported,2 and based on the experience of the first two studies, the calorimeter system has been modified and operated at 1600°C to obtain measurements on the Fe-Si, Fe-A1, and Fe-Cu systems. This paper reports the results of the work. THE MODIFIED SYSTEM It was clear from the earlier results that the most precise measurements can be obtained with the high-temperature solution calorimeter when the solution time is less than approximately 30 sec. This can be achieved only when the bath temperature, Tb, is above the melting (liquidus) temperature of the solute material being dropped. A second point of importance is that the refractories used earlier liberated considerable water so that, although the oxygen potential of the atmosphere in the system was satisfactory for work with nickel and copper, it was too high for work with iron, silicon, and so forth. Third, for work at 1550" to 1650°C, an improved temperature-sensing unit is needed. The modified calorimeter in its latest form is shown schematically in Fig. 1. The refractory brick and the Kanthal-Super heating elements which formed the furnace for heating the solute addition have been replaced by a smaller resistance-heated tube furnace which is insulated with bubble-grain alumina. A more elaborate gas purification system was installed to maintain a satisfactorily low oxygen potential in the atmosphere of the calorinieter chamber and of the solute addition furnace. As was the case in the earlier work, at the beginning of a run the calorimeter chamber is evacuated and then filled with purified argon so that a total pressure slightly in excess of 1 atm is maintained during the run. When either of the furnaces within the enclosure attains a red heat, 6 pct H2 is added to the atmosphere. Throughout the run, gas from the calorimeter is circulated through a de-oxidation system at the rate of approximately 5 standard liters per min; the changeover time for the gas within the calorimeter enclosure is approximately 1 hr. The essential stages of the deoxidation system are: a copper furnace at 600°C, a drying tube of anhydrite, and a titanium furnace at 800°C. The oxygen potential of the gas stream in the purification system can be monitored at several points by a stabilized zirconia oxygen cell. This cell is invaluable in detecting the development of leaks in the container vessel and the gas circulating system. The installation of the solute-addition furnace allowed either of two types of temperature-sensing units to be mounted on a water-cooled probe. The first was a small optical device using a silicon diode that was

Jan 1, 1968

By C. S. Barrett

W. Hofmann, J. Ziegler, and H. Hanemann—Having dealt with the same alloys in the winter 1941 to 1942, we want to give a short report on the generating of the hexagonal kappa phase by deforming the supersaturated alpha phase, which we then observed. This work was delivered as a Doctor of Engineering dissertation to the Technical University of Berlin by J. Ziegler in 1942. It still exists in two copies, somewhat damaged, a brief publication of it having been issued in Fiat-Review. Our work was started from the alloy Tombasil with 4.5 to 5 pct Si, 14.5 to 14 pct Zn, the rest Cu. Torpedo propellers were die cast from this alloy in Germany during the war. In order to improve this alloy, annealing was tried. By this treatment the alloy became at the same time harder and more brittle. A further research of this process was made in the Got-tingen University30 and the "Institut fÜr Metallkunde" of the Technical University of Berlin. It soon was apparent that the Cu-Si diagram at our disposal15,31,32 would not fit the observations. For this reason the pith of the matter became from then on the Cu-Si system. At that time we did not know of Smith's* and Andersen'sm latest diagrams. We first knew of them from Dr. Barrett's publication. Twenty-two alloys containing 2 to 11 pct Si were melted in a nitrogen atmosphere and generally homogenized for 2 to 4 hr at 800 °C. Part of the samples were then annealed at 700°, 600° and 500°. Annealing was followed by quenching in water. The phases corresponding to the various temperatures were identified by X-ray and microscopy. The Debye-Scherrer photographs generally were made of filings. The latter were produced after the last anneal of the samples, then equally annealed another 30 min in evacuated glass tubes and quenched in water. In the region of concentrations examined, the Cu-Si phases already known to us were observed: alpha, kappa (then called beta by us), gamma. By hot exposing an alloy of 7.69 pct Si at 800" and 750°,

Jan 1, 1951

THOSE NOT MARKED ARE MEMBERS; MARKED THUS t ARE ASSOCIATES. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. JUNIOR MEMBERS ARE MARKED II. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. AARONS, J. BOYD, Genl. Mgr., Chaffers G. M. Co., Boulder City, West. Australia. '05 ABADIE, EMILE R., Min. Engr Box 291, Porterville, Tulare Co., Cal. '76 ABBOTT, CLARENCE E., Genl. Supt., Iron Mines Div., 1405 Minnesota Ave., Bessemer, Ala. '04 ABBOTT, J. W., Min. Engr., "St. Omer," 123 N. Grand Ave., Los Angeles, Cal. '94 ABBOTT, Louis BENJAMIN, Chief Engr., Consolidation Coal Co., Elkhorn Div., Jenkins, Ky. '15 ABBOTT, ROBERT R., Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 ABE, ASAKA Yamagano G. M., Satsuma-Gori, Satsuma, Japan. '14 || ABRAHAMS, A. I., Student 1391 Madison Ave., New York, N. Y. '14 tACKER, E. O'C., Met Bethlehem Steel Co., Bethlehem, Pa. '86 ACKER, LOUIS K., JR., Min. Engr 565 Highland Place, Bellevue, Pa. '08

Jan 1, 1917

By J. Parke Channing

THE growth of and profession depends on meeting and solving new problems. It is a continuous process. 'A period free from new, or hitherto unknown, questions will be a period of arrested development in the profession it affects. The present generation has witnessed a' mechanical development that has been truly marvelous: Almost every day marks the advent of a new, or the improvement of an old; process, method or machine. Wonders are now commonplace. The impossible is regularly accomplished. Yet, with all our progress in every realm of science and with our development in the engineering field, advances which have made possible the marvelous growth in industry, we have not made commensurate gains in methods affecting the human factor. Without the cooperation of the worker, we shall always fall short of our goal in a mechanical or statistical sense. If we do not make the individual members of the human family strong, healthy, happy, and ambitious for better things for themselves and their children, we will have failed utterly, for that is the real reason for our existence as men and the purpose of our organized effort as an engineering group. Thomas A. Edison

Jan 1, 1921

By Rossiter Raymond

This regiment, originally known as the First Engineer Reserve, will be remembered as the one recruited in New York City through the efforts of the Joint Military Committee of the National Engineering Societies. It was sent to England in August, 1917, and, after a few clays, forwarded to France and attached for immediate service to the British Expeditionary Force, without any opportunity for further field-training. This circumstance has led in some quarters to the impression that the regiment was one of engineers and mechanics merely, and had never been drilled under arms; whereas, in fact, it had received such instruction at Fort Totten for some time previous to its embarkation. It is true that in the famous affair of the German counter-attack after Byng's victory near Cambrai, the men of the Eleventh Engineers fought with pick-axes and tools, as well as with rifles borrowed from dead or wounded soldiers; but that was because they had left their own arms in camp, while doing the railroad-building work to which they had been detailed. The accomplishment of that work is really more remarkable than the behavior of the men under a German surprise-attack. It was before that counter-attack, and immediately after Byng's advance, that Field-Marshal Haig issued his despatch, announcing that the engineers deserved as much credit for that victory as the infantry, having performed miracles in keeping the railway transportation up to the fighting line. Indeed, the subsequent scrimmage, of which so much has been said, was ?Date possible only by the extraordinary position of the engineers at the very front, instead of in the rear, as might have been expected of them. A letter recently received from an officer of the regiment says: We have only recently been receiving the New York papers of early December, in which our regiment seems to have received much favorable mention. The stories were, in the main, true. Our men behaved themselves creditably, and certain of the officers received special mention for valor. Two of our 2d lieutenants were pro-moted to 1st lieutenant rank by special orders of General Pershing for "gallant con-duct in action," and about four others would have been decorated by the British,

Jan 4, 1918

By R. E. Barnes

An overall view of the perlite industry is concisely presented. The geology, mining, milling, processing, and applications of perlite, as well as the present status of the perlite industry are treated. Perlite, in strict petrological usage, describes a specific variety of volcanic glass in which strain, incident to cooling, yielded a concentric structure of fracturing which may be visible either to the naked eye or under a microscope. In commercial usage, the term perlite includes any naturally occurring acidic glass of volcanic origin that will expand when heated to a suitable temperature. The name perlite is a derivation of perlstein which originally defined "certain glassy rocks (hyaloliparites, hyalo-rhyolites) with numerous concentric cracks, from the fancied resemblance of broken out fragments to pearls."1 While perlite has been known to geologists for many years, it was not until 1941, while investigating perlite for use in enamel, that an assayer in Superior, Ariz., noted the unusual expansion characteristics of the ore. Further investigations were delayed until following World War II when many small plants were built and experimentation in the treatment and uses of perlite began. The Perlite Inst. was organized in 1949 to promote the development of the new industry, establish commercial standards through research, and to explore new uses and markets. The Institute, located in New York, represents some 50 producers in the U.S., Canada, Australia, England, France, Germany, Greece, Japan, Mexico, and New Zealand. In 1949, 71,l002 short tons of crude perlite were produced, sold or used by U. S. producers, and this figure increased to 325,0003 short tons by 1959. Such a rate of increase indicates the rapid and continuing growth of the perlite industry. GEOLOGY Perlite ore in its crude form has been found in seven of the mountainous western states, since un-devitrified siliceous volcanic rocks are limited to this section of the U. S. Commercially operated perlite deposits are normally of Eocene and Oli-gocene age.4 These deposits are often several hundred feet thick and may extend over hundreds of acres. In 1959, 13 companies in six states produced crude perlite, although the output in New Mexico comprised 79 pct of the total domestic crude output. Other states in order of their production were: Nevada, Arizona, California, Colorado, and Utah.5 Foreign deposits of perlite which are either producing or under exploration are Australia, Canada, Greece, Hungary,6 Iceland, Ireland, Japan, Mexico, New Zealand, and Sardinia. The ore may exhibit a variety of characteristics depending partially on its water content and eruption history and may range through many shades from black to white. While these characteristics may vary slightly among deposits, perlite ore from a particular source is normally quite uniform. Available chemical analyses of perlites from a large sampling of domestic deposits were recently assembled by the Technical Committee of Perlite Institute and are presented in Table I. While the ranges given do not apply to a particular perlite, they are an indication of the chemical analysis which may be expected from any presently commercially operated deposit. The specific gravity of the perlite ore ranges between 2.2 and 2.4, and its bulk density when crushed and sized is 75 to 90 Ib per cu ft. MINING AND MILLING Perlite ore is quarried from open pits by conventional power equipment, although blasting has been occasionally employed. The rock is then stock-piled until needed. While the milling of perlite may seem a simple process compared to that required for basic metals, or even other nonmetals, the need for accurate control of particle size becomes extremely important in further processing. The first step in this operation is the primary crusher, which is normally a jaw crusher. Following crushing, the material is dried, if necessary, in a rotary dryer and conveyed to a secondary grinder which may be a rod mill, hammer-mill, or cone crusher. However, the crushing characteristics of the perlite, caused by incipient cooling fractures, requires it be removed from the grinding operation once it is reduced to the required size so as to prevent overgrinding. Following the grinding operations, various size screens are used to separate the ore according to particle sizes required for particular uses. Most plants use two or more stages of crushing with perhaps four stages of screening.

Jan 1, 1961

By Wilford L. Stork

Certain influences of oxygen on iron have been known for many years and it has always been considered one of the worst enemies of the iron and steel founders. Nobody had a good word for it, hence little was done to make use of this oxygen. In all the fields of foundry practice, the desideratum was "melt without oxidation of the metal." In the consideration of the influence of oxygen on cast iron, we must not confuse this condition with oxidized iron caused by poor melting conditions, due to a high bed, heavy charges, low coke ratio, excessive melting rate, high blast, or poor charging. It is admitted that oxygen absorbed by iron melted under these conditions has a deleterious effect on the properties of the iron. The writer has had experience both in the melting under such poor conditions and in remedying these bad conditions and considers the product far inferior to iron melted under normal conditions. As stated by Dr. Richard Moldenke,l such iron has a higher melting point and high combined carbon, is sluggish, and contains slags and oxides in solution in the liquid, causing slag inclusions and gas occlusions, 'thus producing defective castings. This oxidized condition cannot be counteracted or removed by any of the known deoxidizers; it can be remedied only by proper melting conditions. Such iron is redly burned, whereas the iron considered in this paper was melted under normal conditions with moderate blast, correct bed height, light charges of iron, and low coke consumption and is not in this category at all. In 1914, the late J. E. Johnson, Jr., startled the metallurgists of the . world when he published his results on the advantages of oxygen on cast iron.2 His work is so convincing and so logical, in spite of the common and well-established notions on the subject, that nobody has been able to refute a single argument. Such an eminent authority on iron and steel metallurgy as Prof. H. M. Howe has accepted the work in all its details in his latest book.3 The work of J. E. Johnson, Jr., has revolutionized the metallurgy of cast iron and it seems apparent that all future work must include an oxygen determination just as we include silicon, sul-

Jan 1, 1920

By J. H. Westbrook

IT is always of interest to document the origin of real microstructures which closely approach various idealized morphologies. Such instances constitute excellent bases for experimental studies of the effect of microstructure on properties. Typical examples include the eutectoid steels (lamellae) used by many investigators and the two phase Cu-Cr alloys (spheres) recently employed by Hibbard and Hart The present note describes a structure with cylindrical particles. In a study of certain alloys in the Cr-C system, an alloy was arc melted whose composition was very close to the aCr-Cr,C, eutectic (3.2 wt pct C, according to the latest phase diagram published by Bloom and Grant2). The alloy was not analyzed but previous experience with the melting technique employed indicates good correspondence between intended and analyzed compositions with negligible tungsten contamination from the electrode. The phases present in the alloy were identified by X-ray powder patterns as a chromium and Cr,C,. Typical micrographs, presented in Fig. 1, show unmistakable evidence of the cylindrical geometry of the carbide phase. The eutectic grains are randomly oriented and, consequently, only a few show the true fibrous nature of the carbide particles, most being cut so as to show slightly elliptical cross sections. Within any particular grain, remarkable uniformity is to be observed with respect to the size, shape, spacing, and orientation of the carbide particles. Length to diameter ratios have been estimated from the micrographs to be at least 250:1, with diameters of about lp. This alloy may be of further interest from different viewpoints. On the one hand, it might be used to check the applicability of the equations derived by Fullman3 for computing true particle dimensions of cylindrical particles from opaque random sections. On the other hand, it might be possible to extract the carbide particles from this alloy and repack them in a ductile matrix to form a synthetic structure of the type discussed by Metcalfe et al.4 With the large l:d ratio and the small diameter of the carbide fibers, it is likely that the interdefect distance in each fiber is sufficiently great to permit realization of a large fraction of the presumed high strength of the carbide. References 1W. R. Hibbard, Jr. and E. W. Hart: Dispersion Hardening of Copper-Chromium Alloys. AIME Trans., 1955, vol. 203, p. 200; Joun-nal of Metals, January 1955. 2D. S. Bloom and N. J. Grant: The System Chromium-Carbon. AIME Trans.. 1950. vol. 188. p. 41; JouRnal of Metals, January 1950. aR. L. Fullman: Measurement of Approximately Cylindrical Particles in Ooaaue Samples. AIME Trans.. 1953, vol. 197, p. 1267; Journal of Metals. ~ebtember 1953 4 A. G. Metcalfe, C. H. Sump, and W. C. Troy: Fiber Metallurgy. Metal Progress, 1955, vol. 67, p. 81.

Jan 1, 1958

By A. G. H. Anderson, A. W. Kingsbury

Silicon bronzes containing ken are used to a considerable extent in industry, under the trade name of P.M.G. alloys. Various classes of wrought alloys fall in the composition range 1.5 to 3.5 per cent silicon, and 0.5 to 2.5 per cent iron. Castings may contain as much as 6 per cent silicon and 3 per cent iron at present. The constitutional diagrams of these alloys are thus of considerable practical importance. Copper-silicon-binary alloys have been thoroughly investigated by a number of workers, the latest reports being those of C. S. Smith1 and of A. G. H. Andersen.2 Although much work has been done on iron-copper alloys,3 recorded investigations on the copper-rich copper-iron binary constitutional diagram are not numerous. Tammann and Oelsen4 etermined the solubility limits of iron in copper by means of magnetic measurements, and found that the solubility of iron in copper amounts to a fraction of one per cent at 400°C., increasing slowly to one per cent at 800°C. From 800°C., the solubility increases rapidly and attains 4 per cent at iioo°C. Hanson and Ford,5 using electrical resistivity measurements and the microscope, determined a somewhat different solubility limit. of earlier X-ray works on the copper-iron system, very little has been published. The work by Bradley and Goldschmidt6 on copper-iron-aluminum alloys includes some information on the copper-iron binary. These investigators conclude that substitution of iron in the copper lattice decreases the spacings, which is contrary to the evidence of the present work. Hanson and West? have investigated the ternary alloys of copper with iron and silicon. Although their diagrams are valuable contributions to the understanding of these alloys, they did not recognize the kappa phase,l,2,7,8 and their diagrams do not everywhere conform to the phase rule. The present work contains a check by means of X-rays of the solid solubility limit of iron in copper, and an X-ray investigation of the ternary-phase diagram, which, owing to present conditions, it became necessary to curtail considerably. Preparation of Samples Castings weighing about 75 grams were melted under vacuum. The charges were made up of ingot iron, copper cathodes from Laurel Hill, and refined silicon supplied by the Electrometallurgical Co. Alundum crucibles were generally used. The exceptions were alloys 77 and 78, which were melted in graphite crucibles. The ingots were annealed at 800°C. for one week, then samples were cut for chemical analysis. Longitudinal sections of the binary alloy ingots were hammered into plates 1/8 in. thick. Wherever possible, these plates were homogenized at temperatures ensuring

Jan 1, 1943