Search Documents

By B. M. Larsen

In endeavoring to put the art of the steelmaker on a more scientific basis, as a means of securing closer control of the product, we must be severely critical of the basis of any theory we use. In particular, we must be careful to distinguish between factors that are primary and those of only secondary impartance. The concentration relations that determine the slag-metal equilibria, which are usually more or less closely attained, are of course of primary significance, but a, dear picture of the whole process requires that the actual rates of the several reactions be taken properly into account. At the high temperature of the steelmaking furnace, all reactions might be thought to be very rapid, but some of them in fact are not; the essential causes of this condition are important to a proper understanding of the process. This paper aims to present, and to justify, the viewpoint that the most significant reaction is the oxidation of carhon in the metal, the progress of which determines the oxygen pressure levels in slag and metal and produces stirring effects, all of which influence the course of the process as a whole. Reaction Rates at Steelmaking Temperatures General experience in reaction rates makes it almost certain that at steelmaking temperatures equilibrium is attained practically instantaneously when the reactants are well distributed in a single liquid phase —that is, in the so-called homogeneous reactions. The actual slowness of some of the reactions in the open-hearth furnace must therefore be attributed to a relatively slow rate of diffusion within the slag or metal phase, which limits the rate at which the reactants can meet each other in the liquid steel or at its surface. That the reactions can be made to go with great rapidity, by proper mixing and stirring of the reacting phases, is indicated by the following illustrations: 1. In the Bessemer process there is intimate contact between air and the whole mass of metal, and the reactions are complete in a few minutes. 2. Perrinl has demonstrated that by pouring liquid steel into slag contained in a deep ladle, and thereby producing almost a slag-metal emulsion, the phosphorus or oxygen content of the steel is adjustcd immediately. 3. Barret, Holbrook and Wood2 observed a quite rapid rate of desulphurization when powdered calcium carbide was stirred vigorously into liquid iron. 4. When a spoonful of liquid steel is poured into a. mold containing aluminum wire, the formation and precipitation of alumina occurs in the fraction of a second required to freeze the surface layer of the tiny ingot. The first three examples all show that any means of increasing the effective surface between slag and metal and promoting intimate mixture of the reacting phases, thereby obviating the limitation imposed by diffusion, will enhance the speed of the steelmaking process.

Jan 1, 1941

By J. O. Lewis

Oil wells usually reach their maximum daily output shortly after they are completed. From that time they decline in-production, the rapidity of decline depending on the output of the wells and on other' factors governing their productivity. The production curve of a well shows the mount of oil produced per unit of time for several consecutive periods; if the conditions affecting the rate of production are not changed by outside influences, the curve will be fairly regular, and, if projected, mill furnish useful knowledge as to the future production of the well. By the aid of this knowledge the value of a property may he judged, and proper depletion and depreciation charges may be made on the books of the

Jan 2, 1918

By Arthur Crowfoot

As a result of work done, on an operating scale, in its experimental mill during 1920 and 1921, the plan here given was proposed for crushing, grinding, and concentrating low-grade sulfide ores at the Morenci Branch of the Phelps Dodge Corpn. The flow sheet is designed to recover 85 per cent. of the total copper and 95 per cent. of the sulfide copper from ore assaying 2.0 per cent. total copper and 0.3 per cent. acid soluble copper. At present, 1400 tons are treated daily under the conditions of this flow sheet, two 700-ton units having been installed in the 4000-ton concentrator. The run-of-mine ore will be reduced, in the dry-crushing plant, to —6 mesh and then delivered to the concentrator feed bins. The crushing will be done in three stages: (I) Run-of-mine ore is reduced to —2 1/2-in. in a gyratory crusher; (2) the 3-in. ore is reduced to 1/2-in. in 72 by 24 in. rolls; (3) the 1/2-in. ore is reduced to — 6-mesh size in 54 by 24 in. rolls. The 54-in. rolls will operate in closed circuit with electrically vibrated screens, "Hum-mer" type, a conveyor circuit being used to carry the roll product to the screens. Sufficient screens will be installed to pass 1.5 tons undersize per hour per square foot. Fine-ore bin chutes will be piped for compressed air, which will be used intermittently to keep the ore feed in motion if it tends to arch or pipe in the bins. The Concentrator The concentration of the copper and iron sulfides in the ore will be effected in three stages: I. By direct treatment of the —6-mesh crushing-plant product on primary tables, which will recover about 35 per cent. of the original copper content of the ore in a clean granular concentrate. The table middling will be dewatered in Dorr rake classifiers and ground to — 48-mesh in ball mills operating in closed circuit with circulating classifiers.

Jan 1, 1923

By Arthur Crowfoot

As a result of work done, on an operating scale, in its experimental mill during 1920 and 1921, the plan here given was proposed for crushing, grinding, and concentrating low-grade sulfide ores at the Morenci Branch of the Phelps Dodge Corpn. The flow sheet is designed to recover 85 per cent. of the total copper and 95 per cent. of the sulfide copper from ore assaying 2.0 per cent. total copper and 0.3 per cent. acid soluble copper. At present, 1400 tons are treated daily under the conditions of this flow sheet, two 700-ton units having been installed in the 4000-ton concentrator. The run-of-mine ore will be reduced, in the dry-crushing plant, to —6 mesh and then delivered to the concentrator feed bins. The crushing will be done in three stages: (I) Run-of-mine ore is reduced to —2 1/2-in. in a gyratory crusher; (2) the 3-in. ore is reduced to 1/2-in. in 72 by 24 in. rolls; (3) the 1/2-in. ore is reduced to — 6-mesh size in 54 by 24 in. rolls. The 54-in. rolls will operate in closed circuit with electrically vibrated screens, "Hum-mer" type, a conveyor circuit being used to carry the roll product to the screens. Sufficient screens will be installed to pass 1.5 tons undersize per hour per square foot. Fine-ore bin chutes will be piped for compressed air, which will be used intermittently to keep the ore feed in motion if it tends to arch or pipe in the bins. The Concentrator The concentration of the copper and iron sulfides in the ore will be effected in three stages: I. By direct treatment of the —6-mesh crushing-plant product on primary tables, which will recover about 35 per cent. of the original copper content of the ore in a clean granular concentrate. The table middling will be dewatered in Dorr rake classifiers and ground to — 48-mesh in ball mills operating in closed circuit with circulating classifiers.

Jan 1, 1923

By E. F. La Vigne

On Aug. 10, 1884, the Retsof Mining Co. began the sinking of an 18 by 12-ft. shaft at Retsof, N. Y. Rock salt was reached in 1885, in September, at 1008 ft. below the surface. The first salt was shipped in the fall of 1885. A timber breaker was built in 1886. In July, 1895, there was a consolidation of the Retsof Mining Co., the Greigsville Salt & Mining Co., the Livonia Salt Co., and the Lehigh Salt & Mining Co. These consolidated salt companies are now known as the Retsof Mining Co., a subsidiary of the International Salt Go. Eventually all of the mines were closed except the mine of the Retsof Mining Co., at Retsof, Livingston County, New York. On July 6, 1921, about 1/2 mile south of the original shaft arid plant of the Retsof Mining Co., a new 9 by 28-ft. concrete-liried shaft was started. The shaft is 1063 ft. deep from the top of the shaft collar to the bottom of the salt bed. At the same time a reinforced-concrete breaker and other buildings were erccted. This new plant began operations on Dee. 15, 1923. It was designed for a capacity of 3000 tons in 8 hours. Geology The workable rock-salt bed is 1063 ft. below the surface and 326 ft. below sea level, and varies in thickness from 9 to 10 ft. The total thickness is greater than that but is contaminated with shale above and below the pure mineral. The characteristics of the formation are shown in Tables 1 and 2. The bed dips uniformly 0.87 per cent to the south. Prospecting As the salt deposil in New York State is known, very little prospecting has been necessary. Before the sinking of the Retsof No. 1 shaft, a well was drilled to prove the existence of salt. No. 1 shaft was sunk where the well was located. The several salt wells drilled in Livingston Courlty proved generally the existence of salt throughout the county. (See U. S. Geol. Survey Bull. 669: Salt Resources of the U. S.)

Jan 1, 1938

By E. F. La Vigne

On Aug. 10, 1884, the Retsof Mining Co. began the sinking of an 18 by 12-ft. shaft at Retsof, N. Y. Rock salt was reached in 1885, in September, at 1008 ft. below the surface. The first salt was shipped in the fall of 1885. A timber breaker was built in 1886. In July, 1895, there was a consolidation of the Retsof Mining Co., the Greigsville Salt & Mining Co., the Livonia Salt Co., and the Lehigh Salt & Mining Co. These consolidated salt companies are now known as the Retsof Mining Co., a subsidiary of the International Salt Go. Eventually all of the mines were closed except the mine of the Retsof Mining Co., at Retsof, Livingston County, New York. On July 6, 1921, about 1/2 mile south of the original shaft arid plant of the Retsof Mining Co., a new 9 by 28-ft. concrete-liried shaft was started. The shaft is 1063 ft. deep from the top of the shaft collar to the bottom of the salt bed. At the same time a reinforced-concrete breaker and other buildings were erccted. This new plant began operations on Dee. 15, 1923. It was designed for a capacity of 3000 tons in 8 hours. Geology The workable rock-salt bed is 1063 ft. below the surface and 326 ft. below sea level, and varies in thickness from 9 to 10 ft. The total thickness is greater than that but is contaminated with shale above and below the pure mineral. The characteristics of the formation are shown in Tables 1 and 2. The bed dips uniformly 0.87 per cent to the south. Prospecting As the salt deposil in New York State is known, very little prospecting has been necessary. Before the sinking of the Retsof No. 1 shaft, a well was drilled to prove the existence of salt. No. 1 shaft was sunk where the well was located. The several salt wells drilled in Livingston Courlty proved generally the existence of salt throughout the county. (See U. S. Geol. Survey Bull. 669: Salt Resources of the U. S.)

Jan 1, 1938

By Floyd C. Kelley

The literature of the last decade is rich with information relating to the cause and means of control of grain growth in pure metals, but is deficient concerning the role diffusion plays in grain growth, although during this period many new products that depend on diffusion for their properties and success have been developed. Among these are cementation products, produced by calorizing, chromizing, and carbonizing, or by mixing, pressing, and sintering powdered metals such as Syke's iron-molybdenum die material, Genelite, and Elcon Metal (copper, tungsten) etc. This is a fertile field for new developments, but before it can be utilized to the fullest extent there must be a thorough invest,igation of the processes by which diffusion and grain growth take place. Grain growth plays no small part in the process and certainly the physical properties of these products depend largely on the grain size and state of equilibtiuni produced. The field of investigation does not end here, but may be extended to the effect of diffusion on impurities, segregations and dendrites in the broad field of ferrous and non-ferrous metallurgy. A number of years ago the author investigated several of these cases and noted, with striking regularity, the pronounced effect of diffusion in promoting recrystallization and grain growth. An example of this phenomenon is given in his paper on chromizingl which contained photomicrographs of large radial or columnar crystals produced by diffusion of chromium in the solid state. Another manifestation of this effect was discussed by Austen,2 who showed the part hydrogen plays in the decarburization of steel and the effect of diffusion upon the grain structure. Diffusion of Metals in Iron It seems to be a general law, whenever two metals are brought into intimate contact at a temperature at which diffusion takes place, that a comparatively rapid, or abnormal, grain growth results. The grains

By Floyd C. Kelley

THE literature of the last decade is rich with information relating to the cause and means of control of grain growth in pure metals, but is deficient concerning the role diffusion plays in grain growth, although during this period many new products that depend on diffusion for their properties and success have been developed. Among these are cementation products, produced by calorizing, chromizing, and carbonizing, or by mixing, pressing, and sintering powdered metals such as Syke's iron-molybdenum die material, Genelite, and Elcon Metal (copper, tungsten) etc. This is a fertile field for new developments, but before it can be utilized to the fullest extent there must be a thorough investigation of the processes by which diffusion and grain growth take place. Grain growth plays no small part in the process and certainly the physical properties of these products depend largely on the grain size and state of equilibrium produced. The field of investigation does not end here, but may be extended to the effect of diffusion on impurities, segregations and dendrites in the broad field of ferrous and non-ferrous metallurgy. A number of years ago the author investigated several of these cases and noted, with striking regularity, the pronounced effect of diffusion in promoting recrystallization and grain growth. An example of this phenomenon is given in his paper on chromizing1 which contained photomicrographs of large radial or columnar crystals produced by diffusion of chromium in the solid state. Another manifestation of this effect was discussed by Austen,2 who showed the part hydrogen plays in the decarburization of steel and the effect of diffusion upon the grain structure. DIFFUSION OF METALS IN IRON It seems to be a general law, whenever two metals are brought into intimate contact at a temperature at which diffusion takes place, that a comparatively rapid, or abnormal, grain growth results. The grains

Jan 1, 1928

By R. Schuhmann, O. W. Moles

at temperatures of 1150°, 1250°, and 1350°C for liquid copper sulphides ranging in composition from saturation with Cu to about 21.5 pct S. From the experimental data, activities of Cu, S, and Cu2S in the melts were calculated. Also, the results furnish a new determination of the location of the curve showing the compositions of Cu-saturoted sulphide melts in the CU-S constitution diagram. THE "white metal" made as an intermediate L product in converting copper matte to blister copper is a matte approximating Cu2S in composition. It has long been known that liquid Cu-S mattes can exist at a given temperature over an appreciable composition range, with S:Cu ratios ranging up from a lower limit corresponding to equilibrium of the matte with a liquid Cu phase. The Cu-saturated matte has somewhat less S than Cu2S, although previous measurements of the compositions of Cu-saturated mattes are not in good agreement.'" As the S:Cu ratio approaches and slightly exceeds that for Cu2S, the partial pressure of sulphur gas over the liquid matte rapidly approaches atmospheric pressure,5 so that Cu-S melts with much more S than Cu2S can be made and handled only in pressure apparatus. Accordingly, the liquid copper sulphides of interest in copper smelting and readily studied experimentally fall in a relatively narrow composi- tion range about Cu2S. The freezing points of Cu-S mattes show a maximum of 1129°C near the composition Cu, dropping to 1105oC for Cu-saturated mattes having less S and dropping under 1100°C for higher S mattes.' Estimates of the sulphur pressure and other thermodynamic properties of liquid Cu,S were made by Kelley; based on extrapolations from equilibrium measurements on solid Cu,S. More recently, Cox and coworkers' studied equilibria in the reaction: Cu,S + H, e 2Cu + H,S over the temperature range 700" to 1250°C. They measured equilibrium H2S:H2 ratios presumably with both the sulphide and the metal phase present, so that their data above the melting point of Cu,S should measure the S pressure of Cu-saturated sulphide melts. The sulphur pressures of liquid copper sulphides of several S:Cu ratios at their freezing points can be estimated from data given by Posnjak, Allen, and Merwin." However, beyond these few data, no systematic study seems to have been made of the relations of sulphur pressure and other chemical properties of liquid copper sulphides to composition and temperature. The measurements of the sulphur pressures of liquid copper sulphides reported in this paper represent a first step in the quantitative study of the chemistry of mattes. Similar work is planned on

Jan 1, 1952

By Hugh Henton

THIS paper is the result of an investigation made in association with Dr. Charles H. Fulton. Early in 1918 a search was started for methods of utilizing, in the manufacture of basic refractories, certain domestic resources in magnesites, dolomites, and magnesian limestones. Much information was collected during that year and during 1919 regarding magnesite and dolomite deposits. During 1920 and 1921 a research was made into methods of calcining dolomite and separating magnesia therefrom. Some success was attained and many new ideas were brought out in connection with the preparation and utilization of magnesia in the form of "caustic" or light-burned material as well as in the form of refractory or "dead-burned" material. Stimulated by this success, much advance has been made in manufacturing processes for the "plastic magnesia," so called, used for magnesia cement, stucco, flooring and otherwise in the structural industries.

Jan 3, 1926

By Robert Glass Cleland

WALTER DOUGLAS succeeded his father, Dr. James Douglas, as president of Phelps Dodge in 1916. Before assuming office, the new president had been assayer at Bisbee, superintendent of the Copper Queen, general manager of all the Phelps Dodge mining interests, and altogether had spent a full quarter of a century in various phases of the company's business. Energetic and imaginative, experienced and courageous, he had need of all these qualities before he surrendered the direction of affairs into younger hands, fourteen years later. For the period of his administration was one of sudden ebb apd flow, flush production, drastic curtailment, quick recovery, and near-disaster. In 1917, soon after Walter Douglas became president, Phelps, Dodge & Co., Inc., which had been formed in 1908 as a holding company, went through an internal reorganization for the purpose of simplifying the structure and changing it from a holding company to an operating company. The Copper Queen Consolidated Mining Company, which had the necessary charter power and authority to carry on the business of any and all the subsidiary com-

Jan 1, 1952

By W. J. Rude

LARGEST of the known commercial deposits of pebble phosphate are those found in Polk County, Florida. The phosphate bed, commonly known as the matrix, will consistently average 6 to 9 ft. in depth, and is found under 3 to 60 ft. of over-burden. The phosphate pebbles, white and black in color, varying greatly in grade, are found imbedded in a matrix of sand and clay; and range in size from the fines to pebbles 1 1/2 in. in diameter, although the average coarse size is approximately 1/2 in. in diam¬eter. On some of the washers all material under 14 mesh is lost. High-grade phosphate (75 per cent plus of bone phosphate of lime, CasP2Oa) is generally soft, the pebbles breaking up during the mining operation and in pumping; low-grade phosphate, 67 to 69 B.P.L., is black in color with hard pebbles with no loss encountered in pumping.

Jan 1, 1941

By Victor A. Phillips

A series of strips of a Ni-12.7 at. pct A1 alloy were Prepared containing cubical y'(NisAl) precipitates with edge lengths from 60 to 500A. A particle-free solution-tveated strip was included for cornparison. They weve cold-rolled 95 pct and the effects of particle size on the isochronal (1/2 hr) annealing behavior between 300° and 950°C studied (by hardness and light and electron microscopy). It ulas inferred that the particles deformed with the lnatvix becoming lamellae which remained coherent. Comparison with published data fov pure nickel showed that aluminum greatly re-tavded softening and recrystallization, but it made little difference whether or not particles were present. The presence of pakticles led to a heterogeneous distribution of precipitates after annealing at 700" to 750°C. Recovery was not detected. Recrystallization occurred by the growth of new grains into unrecrys-tallized material. In a previous study by the author,' the growth of Ll2-type ordered yl(Ni3Al) precipitates was followed in Ni-12.7 at. pct A1 alloy as a function of aging at 600" and 700°C. The particles were showo to be cubical in shape in all sizes from 50 to 3000A and remained coherent. This work was used as a guide in preparing the starting structures for the present study of the effect of these particles on the annealing behavior of heavily cold-rolled strip. Another question of present interest was whether dislocation and particle hardening were additive, since the structures before rolling ranged from solution-treated to peak-aged to overaged. Also, precipitation might occur on annealing after cold-rolling. Reference may be made to other papers2"5 for previous work in this relatively unexplored field and only some recent work will be mentioned her:. phillips2 studied the effect of deformable 0 to 590A-diam cobalt particles on a Cu-3.23 pct Co alloy rolled 95 pct and found that the particles, which rolled out into thin lamellae, impeded softening and recrystallization. Tanner and servi3 likewise studied the annealing of cold-swaged Cu-2 pct Co alloy containing 150A-diam particles and found impeding effects. Haessner et a1.,4 on the other hand, found that incoherent 2-p-diam non-deformable particles of B4C (0.04 vol pct) tended to increase the rate of recrystallization of copper rolled up to 95 pct reduction. They attributed this to the formation of new grains at the particle interfaces. Humphreys and artin' found that nondeformable silica particles in copper rolled to 30 pct reduction accelerated recrystallization if the particle spacing was large and retarded it if the spacing was smaller. Haessner et a1 4 also studied a rolled Ni-Cr-A1 alloy; however, the particles of y'(Ni3Al)-type precipitate were not put in before rolling, but separated during the isothermal annealing at 750°C. No previous work appears to have been carried out on the effect of y' (Ni3A1) particles on the annealing of Ni-A1 alloy. Hornbogen and ICreye7 redetermined the solubility c of aluminum in nickel as a function of temperature T and showed that it was given by c = 32.6 exp(-1940/RT). This relation gives aluminum solubilities of 15.1, 14.2, 12.0, and 10.7 at. pct at 1000°, 900°, 700°, and 600°C, respectively. The phase precipitated from the nickel-rich solid solution is fcc y1 (Ni3A1) which has a Cu3Au -type ordered structure8 and remains ordered up to 1000°C.B EXPERIMENTAL PROCEDURE The alloy used was identical with that used before. Chemical analysis showed 6.27 wt pct (12.71 at. pct) Al, the principle impurities being 0.065 pct Fe, 0.022 pct Co, 0.020 pct Cu, and 0.004 pct C. Bar stock of 1 in. diam was cold-swaged to % in. diam, cold-rolled to 0.300-in.-thick strip, and annealed at 900°C in dry hydrogen. It was cold-rolled to 0.100-in. thickness and solution-treated for 1 hr at 1000°C while sealed in a quartz tube in argon, quenching in iced brine with the aid of a device to snap off the nose of the tube. Lineal analysis gave an average grain size of 0.055 mm. Pieces of strip were aged at 700°C in vacuo for 30 min, 51/4 hr, and 1 week to produce nominal average particle widths of 60, 150, and 500A, respectively, as known from the previous work.' The average diamond pyramid hardness was determined. The heat-treated strips were rolled from 0.100 to 0.005 in., a reduction of 95 pct, and the rolled strips stored at about -5°C. Small pieces were annealed within 1 week for 30 min at temperatures from 300° to 950° ±2°C in a horizontal vacuum furnace. Strips were withdrawn into a cooling zone, giving an estimated initial cooling rate from 950°C of about 50°C per sec. Average diamond pyramid hardnesses were determined on a lightly electropolished spot on the surface of each strip using 300-g load. Each point on the softening curves represents a separate annealed specimen. Sections containing the rolling direction were examined by optical metallography. Selected specimens were electrothinned to the center plane' and examined by transmission at 100 kv in a Siemens Elmiskop I electron microscope. It is well-known that changes in the structure tend to occur when a deformed strip is electrothinned below a thickness of a few hundred angstroms, although this is less serious with a material such as nickel which has a high melting point, and also is apt to be less serious when particles are present. Observations were nevertheless confined to thicker regions of the foils with estimated thicknesses over 1000A. No changes were observed due to beam exposure.

Jan 1, 1968

By Paul D. Conatore

INTRODUCTION There are important reasons for a discussion of tungsten resources, reserves, and production in the Circum-Pacific area. First, the world's chief tungsten deposits, as well as most of the world's tungsten reserves and production, occur in this region. It is well known that the world's largest tungsten reserves are located in southeastern China and that for many years, the largest individual mine in the world was there. Although China still has the world's greatest tungsten production, the very high-grade scheelite mine of Canada Tungsten Mining Corporation in the Northwest Territories is the largest producer of tungsten today. There is certainly a great quantity of tungsten in Asia, but the strategic importance of this fact is now offset by the wide distribution of mines and production facilities throughout the world, especially in other parts of the Circum-Pacific area such as Australia, Canada, and the United States. In addition, much of the Circum-Pacific area is comprised of Mesozoic-Cenozoic orogenic belts. These global tectonic units are regarded as very favorable for additional tungsten deposits, particularly scheelite-bearing tactites, and consequently, prospecting and exploration will most likely be concentrated in the Circum-Pacific area. Second, tungsten must be regarded as one of the, most important metals of modern industry because of its very special properties. It has the highest melting point, the highest tensile strength at elevated temperatures, and the smallest compressibility of any metal. The metal also possesses a very high density, excellent corrosion resistance, good thermal and electrical conductivity, and a low coefficient of expansion. As a result, tungsten has found increasing importance in a wide range of industries. From the filament in an electric lamp, to cutting tools and drilling bits, to the exotic radiation shields that protect supersonic aircraft and spacecraft, tungsten plays an indispensable role in our daily lives. The primary objective of this paper is to present an overview of important facets of known and suspected tungsten in the Circum-Pacific area. Resources, reserves, current production, planned capacity expansions, and new operations, as well as an assessment of the probability for development of deposits in the Circum-Pacific area, are discussed. RESOURCES The average crustal abundance of tungsten has been estimated at 0.0015 kilograms per tonne. A comparison of the abundance of various metals in crustal rocks to that of tungsten is presented in Table 1, which shows that tungsten abundance is similar to that of its commonly associated metals, tin and molybdenum. Table 1. AVERAGE CRUSTAL ABUNDANCE OF VARIOUS METALS (Grams per Tonne) [ ] With careful thought, it can be realized that tungsten ore deposits result from the concentration of the metal, through normal geologic processes, to levels substantially greater than its average crustal abundance. The minimum technologically and economically workable tungsten concentration, or cutoff grade, is a function of (1) deposit tonnage, (2) mining and milling methods, (3) production tonnage, (4) capital and operating costs, (5) tungsten market conditions, and (6) value of associated recoverable metals. The tungsten cutoff grade that is currently exploitable at a profit varies from 0.09% W03 to 1.55% W03, reflecting concentration factors from 470 to 8200, as shown in Table 2. Table 2. CURRENT TUNGSTEN CUTOFF GRADES [ ]

Jan 1, 1982

By R. S. Handy

THE properties of the Patiño Mines and Enterprises Consolidated, Inc., a New York corporation, are near Llallagua in the department of Chayanta in the west central part of Bolivia, South America, about 80 miles southeast of Oruro and 250 miles southeast of La Paz, the largest city in Bolivia and its virtual capital. The properties are accessible by railroad from three points on the west coast-from Mollendo, Peru, across Lake Titicaca, from Arica by way of La Paz, and from Antofagasta, Chile. The latter route, although the longest, is recommended by the companies as affording a more gradual introduction to the high altitudes; the mine being 13,000 ft. above sea level. The company operates its own railroad from its properties at Uncia to Machacamarca on the Chile & Bolivia R. R., a distance of 60 miles. This railroad is well equipped and well operated, and its location among the mountains surrounding Uncia represents excellent engineering skill. In fact all of the railroads, although they are of only a meter gage, are remarkable for the excellence of their construction, the arrangement of their dining and sleeping cars and the precision of their operation. There is only one drawback to rail- road and hotel accommodations and that is the absence of heating facilities, which does not seem to affect the natives but keeps a tenderfoot's teeth chattering continually. The company is a consolidation of the Patiño company, owning properties at Uncia, with the Compafiia Estanfera de Llallagua, a' Chilean corporation owning contiguous properties at Llallagua. Before the consolidation these companies were deadly enemies, and there still remain at the surface plant at Uncia the fortifications and underground defences provided during the warfare between the two factions. Also, in the Azul, or "Blue" tunnel at the junction line between the two properties is a strong steel barricade still bearing marks of the bullets fired during the various armed tilts between the workmen of the two companies. The headquarters for the mining operations and the milling plant have been moved since the consolidation from the original location at Uncia to the Llallagua side of the mountain, where the Chilean company's operations were carried on. The historic old town of Uncia, with its massive stone buildings of Spanish design, is a wreck, while the Llallagua side is being rapidly built up with modern structures.

Jan 1, 1929

By Robert H. Richards

(Read at the Amenia Meeting, October, 1877.) DURING the summer of 1870, I had an opportunity to visit the laboratory of the late David Forbes, Esq., in London, and was much interested in a labor-saving device which lie had attached to his agate mortar. The mortar was placed in the centre of a small table, and about ten inches to the right of the mortar, a post, perhaps two

Jan 1, 1878

By W. A. Backofen, A. T. English

The kinetics of re crystallization were determined metallographically for a 3-1/4 pcl Si-Fe rapidly compressed at temperatures of 710° to 911°C, and held for various times at the working temperature. As in re crystallization following cold wwk, the time for re crystallization was reduced by increased temperature and strain. Nucleation occurred chiefly at grain edges, although other pre-existing interfaces, notably inclusions, also served as nucleation sites. The importance of intragranular nucleation to grain refinement in hot working is pointed out, together with some possible techniques by which nucleation might be induced within the grains. The observed isothermal growth rates are quite accurately described by the equation G = 4 x 10-'/t (cm per sec), independent of temperature and strain at all but the shortest times. Changes in G during recrystalliza-tion can exceed two orders of magnitude. It is argued that release of stored energy associated with lattice defects cannot adequately explain the time dependence. A suggested alternative involves processes of solute segregation and desegregation in the unrecrystallized matrix and at the moving boundary, respectively. EFFORTS to improve hot-working practice are hampered by an incomplete understanding of the fundamental metallurgy involved. Research directed at establishing the required basic foundation falls into two categories, the first concerned with measurement of mechanical properties under the conditions of high temperature and strain rate which characterize such processing, the second focused on structure and its relation to the deformation conditions. Rossard,' Rossard and Blain,2 and Hardwick and Tegart have conducted many high-speed, high-temperature torsion tests on various metals. One of their objectives was interpretation of stress-strain curves in terms of the structures of specimens rapidly quenched following interruption of twisting. They showed that appreciable hardening occurred in the early part of the test, and that this hardening reflected the concurrent development of an increasingly dense substructure within the grains. The detailed nature of this substructure was observed to depend on the ease of polygonization which, at least in fcc metals, varies with the stacking-fault energy.= By holding specimens after interruption but before quenching, the nucleation and growth of new grains could also be studied. Some success has been realized in relating the microstructure of hot-rolled steel to its temperature:strain rate:strain history with such testing.' The same general observations have been made by others investigating rolling4f5 and drop-hammer forging.~-~ Incident to these experiments, some efforts were made to determine the kinetics of re-crystallization as well as the velocity of the migrating boundaries. The results have been largely qualitative, owing to difficulties of interpreting hardness measurements5 and microstructures. The work described here was undertaken to obtain more quantitative information from tests on a material having suitable metallographic properties, and, in this way, to provide further insight into the fundamentals of this practically most important kind of deformation processing. I) MATERIALS AND EXPERIMENTAL TECHNIQUES Materials. Electrolytic etching of a Si-Fe alloy reveals dislocations and substructure in unrecrystallized grains.8'9 This unique characteristic makes possible a precise determination of the extent of recrystallization. For that reason, it was the material selected for all experiments in the present work. The two particular alloys that were used are identified in Table I. A major difference between "A" and "B" is the number of inclusions, as noted in the table. Most of the experiments were made with material "A". It was received as hot-rolled plate 1 in. thick, sawed to 2-in. widths, hot-forged at 1200°C to 5/8-in. rounds, and finally annealed in a mechanical vacuum at 1000°C for 24 hr. The result was substructure-free grains of mean diameter 0.05 cm.*

Jan 1, 1964

By John Brownson

Ge-Si N-N heterodiodes hare been built recently which show promise as high-speed logic devices. Low-resistivity germanium is deposited on silicon substrates held at temperatures above the germanium melting point and an alloyed heterojunction formed. The diodes are fabricated from this material using conventional mesa techniques. Over-all device qualify has been greatly improved by the use of epitaxial silicon substrates, that is, a subsirale consisting of a film of thin, high -resistivity silicon on a thicker Piece of low-resistirily silicon crystal. A semimpirical device design equation has been devised which predicts switching performance fairly well within the range of resistivitics and geometries employed. Switching times 01 0.9 ns and PIV 's of —20 v are typical of the better 10-ma diodes. Switching times as low as 0.5 ns have been observed for 10-ma diodes and as low as 2.8 ns for 200-ma diodes. With further development it should be possible to improve switching speed by a factor of four. IN our laboratory, Ge-Si heterodiodes have been built recently which show promise as high-speed logic devices. The diodes have been built using a process reported in some detail in an earlier publication.' The process in short involves alloying a thin film of low-resistivity germanium into a silicon substrate. the germanium having been transported and deposited by the well-known Theuerer halide reduction process.2 This process contrasts with that reported earlier by Oldham who used an essentially conventional direct epitaxial deposition technique.3 Oldham's process, unlike ours, requires cleavage of the silicon sample inside the reactor furnace the instant prior to deposition. Our process has the advantage of yielding large-area macro-scopically plane heterojunctions. Heterodiodes in general have several interesting properties. Without attempting to summarize the theory of heterojunctions.4 two of these properties which have direct relevance should be mentioned. First, N-.V and P-P heterojunction diodes rectify alternating current. Provided that either the band gap or the electron affinity of the two materials is different (which in general is the case), electronic barriers will exist in the junction band structure. When the device is sufficiently forward-biased, the barriers shift so as to permit current flow, and when it is reverse-biased. the barriers block current flow. Second, for N-N and P-P heterodiodes. the foward-conduction process involves majority carriers only. Consequently. when such a device is turned off. there is no minority-carrier storage and hence the diodes switch on and off quite rapidly. As we have reported earlier. N-P and N-N Ge-Si heterodiodes have been built in this laboratory. As one would predict from theory, the N-P heterodiodes were rather slow in turning off while the N-N's were quite fast. Similarly, the turn-off time of the N-P's increased rapidly with forward current while that of the N-N's was independent of forward current. Both N-N's and N-P's were moderately photosensitive. Photocurrents resulting from normal room illumination were as high as 1 µa at 1 v for small-area devices. The most disappointing parameter of the early N-N devices was reverse leakage.' The reverse characteristic was invariably "soft" and leakage at only several volts reverse bias was intolerable. The reverse characteristic was greatly improved by using higher-resistivity silicon substrates. Leakage becomes large at voltages about one third of the avalanche voltage one would expect of a P-N homo-junction formed on silicon of the same resistivity. Thus leakage could be reduced to reasonable limits by using unconventionally high-resistivity silicon. Medium-power diodes formed on 30 ohm-cm substrates leaked typically 15 to 50 µa at 100 v reverse bias. The use of high-resistivity silicon substrate material, however, created a new problem. In order to have an acceptable forward-conductance characteristic. the area of the diodes had to be increased. With this increase in area, the capacitance increased. Switching time for N-N heterodiodes is essentially a linear function of capacitance. Thus when the resistivity was raised. so was the switching time. A SEMIEMPIRICAL HETERODIODE DESIGN EQUATION As a result of our experiments with a limited range of diode geometries and resistivities. a semi-

Jan 1, 1965

By G. R. M. Del Giudice

A survey of the flotation literature of the past 10 years indicates an increasing use of the microscope as a tool for investigation. Thus, the metallurgical microscope has been used by Tucker and Head;' Taggart, Taylor and Ince;2 Ince,3 and del Giudice4 to examine mineral surfaces that had been subjected to the action of various flotation reagents and to the action of slime pulps. It has also been used by Gaudin, Groh and Henderson;5 Martin;6 Morrow and Griswold;7 and others to examine bakelite briquets of mill products. The microscope with transmitted light, both with bright-field and dark-field illuminations, has been used by Taggart, Taylor and Knoll8 and by Ince9 to observe Brownian motrement and flocculation in flotation pulps. The use of the microscope at low-power magnifications with incident illumination for the examination of mill products has been known for years.10 Finally, del Giudice11 has used a relatively new type of illumination, the Ultropak, for the examinntion of slime-coatings.

Jan 1, 1935

By C. A. Herbert, C. M. Young

WithIn the past few years, considerable development has been made in the coal-mining industry in Illinois and Indiana and it is the purpose of the authors to record its most important phases. Perhaps the two most striking features are the entry into the producing fields of certain large consumers of coal and the magnitude of some of the new operations. Mines are now being equipped by the Chicago & Northwestern R. R., the Chicago, Burlington & Quincy R. R., the Standard Oil Co., of Indiana, and the Union Electric Light & Power Co. of St. Louis. Besides, the U. S. Steel Corpn. has increased its coal-mining activities by commencing operations on its large holdings northeast of Benton, Franklin CO., Ill. Until recent years, the supply of coal has commonly been adequate and prices have generally been favorable, especially to large consumers, as the magnitude of their purchases enabled them to obtain satisfactory quotations from producers. In fact, most consumers of coal have believed that they could buy their fuel more satisfactorily in the open market than they could produce it themselves. The entry of the United States into the war was accompanied by various disarrangements of industrial conditions, and a demand for coal in excess of the supply seemed likely to be experienced for an indefinite period. Under these circumstances it seemed that the greatest assurance of a supply of fuel was its production by the operation of mines. In the case of the Chicago & Northwestern R. R. and the U. S. Steel Corpn. the production of coal has been carried on for many years with satisfactory results, but the C. B. & Q. R. R., the Union Electric Light & Power Co. and the Standard Oil Co. of Indiana had not been producers of coal, at least in this district. Apparently the most impressive feature of the newest mines is their capacity, for in some cases it is planned that production shall be in the neighborhood of 1000 tons per hr. There are mines now in this field having nearly that output, but these were not planned for such output; in fact, when the shafts were sunk and the machinery installed it was generally supposed that the daily outputs would be only in the neighborhood of 4000 to 5000 tons. Incidentally, there has risen

Jan 1, 1920