Search Documents

By G. A. Swanquist, E. M. Morales

INTRODUCTION The idea of water management and control at the Church Rock Mill operations began to take shape in February 1979. At that time, we were already investigating the feasibility of decreasing the fresh water requirements so that the solids would become the limiting factor in tailings impoundment utilization. The area for solution evaporation could be kept at a fraction of the normal requirements under the standard process of full water usage. The Church Rock Mill is an acid leach circuit followed by solids/liquid separation with thickeners in counter current decantation, and solvent extraction. Following the normal design of acid leach circuits, reuse of tailings solution was not incorporated in the original mill process design. INITIAL WATER CONTROL INVESTIGATIONS The investigations to decrease the fresh water requirements centered around modifying the grinding circuit from the present semi-autogenous grinding (SAG) mill in closed circuit with hydrocyclones, to open circuit grinding with a rod mill. The open circuit grinding with the SAG mill and rod mill in series had the potential of decreasing the water requirements for grinding and leach dilution by approximately 50% or 1.4 m3/min (300 gpm). The grinding pulp density would be maintained at 70 to 72% solids, and the leach dilution to 50% solids would be accomplished with acid tailings liquor recycle. In such a grinding circuit arrangement, the SAG mill would provide the primary or coarse grind, and the rod mill would be used for the fine grind. By the SAG mill and rod mill series grinding method of water control and other secondary water controls in various places downstream from the grinding circuit, the required necessary evaporation area was estimated at 120 acres of liquid surface. A second method of water control at grinding was investigated. A two-stage cyclone classification circuit appeared to have a good potential of achieving the same water reduction at a much lower capital and operating cost. However, in retrospect, this would not have been a viable method since a high slime recycle load would have been established hindering classification. The use of reagents to neutralize the acid tailings solution was not considered seriously at that time, since it would have materially increased operating costs, although it would have also allowed more tailings solution recycle and consequently, less fresh water usage. However, with the tailings solution deposition area available at that time, it was not then necessary to incur the high cost of neutralization. The control expected by the series grinding of semiautogenous and rod mills would have been sufficient to maintain a water consumption/evaporation equilibrium well in line with the available land area. IMPLEMENTATION OF NEUTRALIZATION OPERATIONS During the summer of 1979, the UNC Church Rock Mill experienced a tailings dam breach which resulted in a prolonged mill shutdown. Upon resumption of operations at the end of October 1979, tailings deposition was restricted to a small portion of the tailings impoundment area. Figure 1 shows the general tailings area and the limits of the present deposition area in the central part including the borrow pits. These borrow pits had been excavated to provide materials for tailings dam construction. Immediately after resumption of operations, it became evident that it would be necessary to control the quantity of liquid to be evaporated because of the small confined area available for tailings solution deposition and to maximize the deposition time in the tailings area. The water control required had to be exercised on a large scale, and to be in operation as quickly as possible. An obvious solution was to reuse the tailings liquor in mill process. Immediate steps were taken to install the necessary equipment for tailings neutralization on an interim basis. Anhydrous ammonia was selected as the primary neutralization reagent since it was the quickest system that could be placed in operation. Previous laboratory tests indicated fair results with ammonia neutralization. Such a system required a minimum of installed equipment and handling. INITIAL NEUTRALIZATION OPERATIONS Actual neutralization operations began on November 26, 1979. The raffinate solution which normally would have been discarded was pumped to a 3.7 m (12ft) diam by 4.3 m (14ft) tank for reagent contact, see Figure 2. At this tank, anhydrous ammonia was added directly from the tanker trailers and controlled at pH 7.0 nominally. Agitation was provided by air sparging. The neutralized product formed a highly viscous slurry in the grinding circuit which resulted in pumping and cyclone classification problems.

Jan 1, 1982

By G. M. Willis, F. L. Hennessy

The oxygen pressure in equilibrium with silver and Ag2O-B2O3 melts has been measured between 800' and 900°C, to obtain the thermodynamic properties of the liquid. The compound Ag20. 4B20:1 appears to exist in the liquid, which shows marked heat content and entropy effects. A KNOWLEDGE of the thermodynamic properties of binary liquid silicates, borates, and phosphates would be of considerable assistance in the interpretation of the behavior of multi-component metallurgical slags. However, the literature contains comparatively few studies of the thermodynamics of binary slags. The system Ag20-B,O, attracted our attention as it was known to give a single liquid phase,',' in which high contents of silver could be obtained (up to 61 pct Ag according to Foex2). Further, it would be expected that the partial pressure of oxygen over melts in equilibrium with metallic silver could be used to determine the activity of Ag2O in the Ag,O-B,O, system. In many respects, it may be expected that the reaction of a basic oxide with boric oxide would be analogous to its reaction with silica. Liquid immiscibility frequently occurs in both borate and silicate systems. With B2O3 and SiO reaction with a basic oxide presumably involves a breakdown of the three-dimensional network of the acid oxide by reaction with oxygen atoms common to more than one silicon or boron atom. Ag2O-B2O3 was therefore investigated as a model of a slag system in the hope that its thermodynamic properties would assist in understanding those of other systems. Several methods for determining the activity of a component in a slag have been described in the literature. Chang and Derge" used high temperature electromotive force measurements to obtain the activity of SiO2 in CaO-SiO2 and Ca0-Al203-Si02 slags, but the cell reaction in their work is not clear. low has used rate of volatilization and vapor pressure measurements combined with phase diagrams to obtain activities in the systems KO-SiO,, Na,O-SiO, and Li,O-SiO," and PbO-SiO26 Taylor and Chipman7 extrapolated their results for the distribution of FeO between liquid iron and CaO (+Mg0)-FeO-SiOl slags to obtain the activity of FeO in the binary FeO-SiO2 system. In principle, one of the most direct methods for obtaining the activity of a metallic oxide in a phase is by comparison of the equilibrium oxygen pressure for the system metal-pure oxide with that of metal oxide-containing phase. Schenck and othersa have studied the stabilization of Ag2O on combination with other oxides (MO,) in the solid state by measurements of the oxygen pressure in systems of the type Ag-Ag,O-xM0,-MOy-0, (gas). Schuhmann and Ensio" have determined the activity of FeO in iron silicate slags in equilibrium with solid iron, using CO/CO2 mixtures to establish known partial pressure of oxygen. Although the method gives the activity of FeO without ambiguity, the slag is not a binary system, and interpretation of the results in terms of the hypothetical binary system FeO-SiO, is not possible. If a metal is solid at temperatures at which the properties of the slag containing its oxide are to be studied, this method has the considerable experimental advantage that the metal can be used as the container for the slag, and contamination by contact with refractories is avoided. In this work, crucibles for Ag2-B,O, melts were made from silver, and the liquid brought to equilibrium with definite pressures of oxygen gas. The oxygen pressure PO, thus fixes the activity of Ag20 in the liquid silver borate. For the reaction at a given temperature. is substantially constant, is directly proportional to the square root of the equilibrium oxygen pressure. Varying the oxygen pressure changed the silver oxide content of the liquid and it was possible to obtain the activity of Ag2O over a range of composition. Experimental Procedure In principle, the method consisted of bringing melts in silver crucibles or boats to equilibrium at a fixed temperature under a definite pressure of oxygen and analyzing the glass after solidification. Materials: B2O3 glass was prepared from A.R. quality boric acid by fusion in platinum. The silver

Jan 1, 1954

By R. M. Hudson, P. E. Perry

Weight-gain data obtained by nitriding low-carbon sheet steel in an amrnonia CNH,) atmosphere indicated that the process obeyed a parabolic rate law. The calculated actization energy for nitriding in the range 964" to 1268°F agreed reasonably well with published data. At 1358"F, rate data indicated that the activation energy decreased. Weight-gain data obtained by uszng mixtures of NH3 -Nz at 1268°F containzng jrom 10 to 100 zol pct NH3 also obeyed a parabolic rate law. The rate of 'nitriding increased with an increase in the NH3 content of the gas Mixture. It is well-known that steel heated in gas mixtures containing ammonia (NH3) takes up much larger quantities of nitrogen than steel heated in nitrogen, both gases having a total pressure of 1 atm;' this phenomenon can presumably be attributed to the catalytic decomposition of NH3 on the steel surface to furnish nascent (monatomic) nitrogen. This process was studied bv Brunauer. Jefferson, Emmett, and Hend-ricks at furnace temperatures of 752" and 831°F2 using mixtures of NH3 in Hz. Englehardt and wagner3 reported that, at a furnace temperature of 914°F and under their experimental conditions, both nitriding and denitriding were controlled by the rate of gas-metal reactions at a steel surface rather than by the rate of diffusion of nitrogen in iron. The present study was undertaken to obtain information on the kinetics of nitriding low-carbon steel strip at higher temperatures so that practical rates for short-time strip-annealing treatments could be estimated. Variables studied included time: temperature, and NH, content in the annealing atmosphere. Mechanical and chemical characteristics of steel nitrided in this manner will not be considered in the present article. MATERIALS AND EXPERIMENTAL WORK The samples used were from a commercial low-carbon steel, 0.0244 cm thick, in the cold-reduced condition. The chemical composition of this steel is given in Table I. Panels were cut to 5.1 by 17.8 cm, degreased in toluene, and weighed just before treatment. Four specimens were nitrided under each of the experimental conditions. A study was made of the nitriding rate of steel in a 100 vol pct ammonia atmosphere, 740 mm pressure, at five specific temperatures within the range 964" to 1358°F. The nitriding rates of steel in ammonia-nitrogen gas mixtures containing 10, 18, 26, 50, and 100 vol pct ammonia, 740 mm total pressure, at 1268°F were also determined. All atmospheres used were dried by successively passing them through drying towers packed with soda lime and with Linde Molecular sieve Type 4A. Quoted gas compositions refer to those entering the furnace. Specimens were held in the constant-temperature zone of a vertical annealing tube furnace for times of 14, 3, 5, 10, or 15 min. Gas flow rates were maintained at 3.8 cu ft per hr, which was nineteen volume changes per hour for the system used. The rate of flow was selected to provide a high level of free NH3 for cracking on the steel surface where the ammonia gas is most effectively used as a nitriding agent. The vertical annealing tube furnace consisted of a Hevi-Duty tube furnace with a 2 1/2-in.-ID mullite ceramic high-temperature tube. The constant-temperature zone (controlled within 10°F) was about 10 in. long. After each specimen was degreased, a hole was punched in one end, for attaching the specimen by hook to a chain so that it could be lowered into or raised from the high-temperature portion of the tube by means of a power-driven winch. A stainless-steel access port with O-ring seals was connected by suitable glass-to-metal seals to the cool upper portion of the furnace tube. After the weighed specimen was placed in the access port, the furnace tube was evacuated to approximately 10"3 torr, and then the system was flushed thoroughly with the atmosphere under study. When the gas flow rate and constant-temperature zone of the furnace were established, the specimen was lowered into the constant-temperature zone. The atmosphere flowed from the top to the bottom of the vertical furnace tube and was then vented. For all these runs, during the first 3 min of the time the specimen was in the constant-temperature zone of the furnace the specimen was heating up to the tempera-

Jan 1, 1970

By W. L. Hill, W. H. Armiger, S. D. Gooch

The physical properties, chemical behavior under thermal treatment, and fertilizer value of fluorine-containing pseudowavellite (hydrous calcium aluminum phosphate) that occurs as phosphate clay admixed with quartz sand in an extensive deposit near Bartow, Fla., were determined by experiments in laboratory, pilot-plant, and greenhouse. When the mineral was heated at 500°C, 80 pct of the phosphorus became citrate soluble. The heated product, however, deteriorates markedly under moist conditions such as obtain in the soil.

Jan 1, 1950

By S. B. King

IT is the purpose of this article to give those not familiar with the subject an idea of the extent to which coal is mined by machine in the United States; to describe some types of electrically operated coal cutters; and in particular, some of the latest improvements and developments in these machines. Generally speaking, the article deals with the mining of bituminous coal in room-and-pillar mines, as the use of undercutting machines in the anthracite region of Pennsylvania is in its infancy, and when machine mining is referred to bituminous coal is taken for granted. The number of mines in the United States that are operating on the long-wall principle is very limited, and the number of long-wall machines in use is a very small percentage of the total. The advantages of mining by machine may be summed up briefly as follows: A. Increased safety to property and life, due to the large decrease in the amount of powder required when the coal is properly undermined. B. Reduction in the cost of mining. C. Improvement in the quality of the product; and, consequently, increase in market value, due to the greater proportion of lump and screen sizes secured by machine mining. D. Increase in the capacity of the mine, and more rapid development of new mines. E. Ability to mine veins in which the height of the coal or the character of the roof has prevented mining by hand, on a commercial basis.

Jan 6, 1914

By Edward H. Robie

SEPTEMBER usually being a fine month for motoring, we set out with our better half at the end of August in our Studebaker for points West. A combined business trip and vacation. The first night found us 392 miles away, at the Statler Hotel in Buffalo, and the next morning we revisited Niagara Falls for the first time in some forty years. The cataracts were as impressive as ever and certainly worth a day of any vacationist's time, instead of the half hour we could spare before going on to Chicago. The Centennial of Engineering, the hundredth anniversary of the founding of the ASCE, no doubt attracted the greatest gathering of engineers in history but still the attendance was disappointing to most of the forty or fifty societies that participated. Perhaps the time-the two weeks following Labor Day-was unfavorable. Few could afford to spend ten days away from home and business at that time of the year. Fall meetings of the AIME normally attract far more than the 300 that registered in Chicago. The technical program, however, was excellent, especially that arranged by the Minerals Beneficiation and Industrial Minerals Divs. The mineral industry papers of a more general nature that were presented as a part of the Centennial program on Monday and Tuesday of the following week were of high quality and offered by top names but had a meager audience. Undoubtedly the celebration brought engineers and engineering to the attention of millions of people. The pageant at the Museum of Science and Industry proved continuously interesting, showing the progress of engineering following the first use of fire. The show continued for many weeks. A special stamp was issued by the Government, which engineers might well use on their Christmas cards or other mail this year. After six days in Chicago we set out north, first visiting Fairbanks Morse in Beloit and Allis-Chalmers in Milwaukee. Will Mitchell's Basic Industries Research Laboratory is doing interesting work and being installed in more comfortable quarters. The next day at Ishpeming, C. W. Allen arranged for luncheon with a local group of AIME members and we then looked over the new surface plant of the Mather B mine, a model of modern functional design. Then on to a small dinner meeting at Calumet following cocktails at Endicott Lovell's attractive summer home on the lake at Point Mills. The new Memorial Union Bldg. at Houghton, where we were domiciled for the night through the courtesy of Roy Drier, is a beautiful modern addition to the college, a model of its kind.

Jan 1, 1952

By R. J. Teitel

FOUR or five years ago an investigation was initiated to study and develop basic information on llquid metal fuels for future power nuclear reactors. The objective was to find fluid forms of uranium (solutions or dispersions) in low melting alloys. A summary of the different fuels was presented in a recent article by Teitel, Gurinsky, and Bryner.' The combination of uranium and bismuth, with its low thermal neutron cross section and low melting point, is of basic interest to the development of these fuels. Most of the previous effort on the U-Bi phase diagram was done under security regulation. Ahmann and Baldwin' reported their findings on the U-Bi system in 1945. Their results indicated that the phase diagram had at least two compounds and possibly one more. UBi, and UBi were established by chemical analyses of residues after high temperature centrifugation of alloys. UBi, decomposed peritectically at1980°C and there were signs of another reaction above that. UBi melted at a very high temperature, and there were also signs of a monotectic at high temperatures in high uranium alloys. The solubility of uranium in liquid bismuth has received attention by three groups of authors: Bareis,X ayes and Gordon,' and Ahmann and Baldwin.' The latest and most widely accepted data is that of Bareis, and it is included in Fig. 1 along with new data at higher temperatures. Brewer et al." and Ferro"'' have used X-ray diffraction to determine the number and crystal structure of the compounds. Brewer identified the structure of UBi to be a simple NaCl cubic structure having a cell edge of 6.364A. The density of the compound was calculated to be 11.52 g per cu cm. Two other unindexed patterns were presented as possibly belonging to two other compounds. Ferro agreed with Brewer on the crystal structure of UBi and identified the structure of UBi, and U,Bi,. The intermetallic compound UBi, has a tetragonal cell with a = 4.445A and c = 8.908A. The density of the compound was determined and the number of atoms per cell (six atoms) was calculated. The X-ray density reported was 12.35 g per cu cm. The compound UsBir was treated in a similar way and it was reported to have a cubic structure 9.35A on an edge and to contain 28 atoms per cell. The density was given as 12.59 g per cu cm. Teitel reported that there was a compound UaBi, and no UBi, compound. (The difference in the compositions is 3.3 pct U.) This conclusion was based upon the extrapolation of some 20 tie lines in the

Jan 1, 1958

By F. Z. Schellenberg

A recent visit with the engineering students of the Western University of Pennsylvania to the Keeling coal-mine on the south side of Pittsburgh furnished interesting matter to communicate, as may be the case, however, with regard to the striking features of any of our well-arranged larger collieries; for every mine surely appears unique as a whole, though description fails to give that impression, except in particulars.

Jan 1, 1900

Jan 1, 1924

Jan 1, 1924

By William Hume-Rothery

MR. CHAIRMAN, LADIES AND GENTLEMEN: I need not say how much I appreciate the honor of being asked to lecture to you, and how much I would thank you for your kind invitation. It is encouraging to feel that the abnormal restrictions of the war have been relaxed sufficiently to allow a free exchange of scientists between our two countries, and I hope that some of you will be persuaded to go to England, and to visit us at Oxford, so that I may repay a little of the kindness I have received from you. As this is one of the first lectures since the end of the war, I have thought it well to describe some of the advances in the theory of alloys which were made in the years between the two World Wars. From the point of view of theoretical science, these years have been of outstanding interest in the history of metallurgy. They have been years in which the development of new and more accurate experimental methods has led to the revelation of many new facts. At the same time, the theoretical developments have enabled some of these facts to be viewed as parts of a general scheme, and we may say that some of the foundations of metallurgical science have been laid. This work was naturally stopped by the Second World War, and it can therefore be reviewed as one definite stage in the development of our Science. To illustrate the new advances, I shall deal mainly with the alloys of copper and silver, since these have revealed many of the general principles. SOLID SOLUTION At the beginning of our period, the first steps in X-ray crystal analysis had been taken, and copper had been found to crystallize in the face-centered cubic structure (Fig I). The determination of this structure naturally was of immense importance in the understanding of our subject, because it meant that we were at last in a position to appreciate the underlying structure out of which the crystal of copper was built. The earlier science of metallography had shown that in many alloys of copper the addition of a second metal in not too large proportions resulted in the formation of a homogeneous alloy which was regarded as a solid solution of the one metal in copper. Fig 2, for example, shows the so-called equilibrium diagram of the copper-zinc alloys, and here you will see that there is a solid solution of zinc in copper extending to something of the order 35 to 40 at. pct zinc.

Jan 1, 1947

By C. Dirksen

This study investigates whether oxygen consumption during segregated forward combustion may be affected by natural convection. Linear theory indicates that thermal instability occurs in a horizontal porous medium when the modified Rayleigh number N 'Ra exceeds a critical value of about 40. Most experimental results, including those described here, indicate this value to be about an order of magnitude smaller. N ', is derived from "differential similarity" and the proper time scale factor is also obtained. The critical value of N'ra for a horizontal, water-saturated porous medium at atmospheric pressure subjected to a uertical temperature gradient was found to be about 3.0. The ambiguity in the value of N'R, arising when fluid properties cannot be assumed constant is indicated. Natural convection was observed for oblique systems below N 'Ra , while simultaneous horizontal flow did not affect N Racrit. The expected range of values for the various parameters pertaining to segregated forward combustion is indicated and the corresponding values of N 'Ra calculated. Only under very favorable conditions, such as high permeability, high pressure and low top temperature, can the critical value of N 'R, be exceeded. Thickness of the convection layer should not become too large, since the time required to obtain significant mixing is proportional to the square of the thickness. For an oblique combustion frant the conditions for significant mixing may be less strenuous. LNTRODUCTION Laboratory1,2 and field314 experiments have shown that a markedly upgraded oil can be produced by in situ forward combustion. Under certain conditions injected air may move through a high permeability, gas-saturated channel over the oil-saturated layer, while combustion takes place, exclusively, at the horizontal interface (Fig. 1). Such a channel may be a natural gas cap, or it may result from a forward combustion process in which injected air and combustion gases fingered through the top of the formation, causing a premature breakthrough at the production well. In this particular case of segregated forward combustion, the air stream moves parallel to the combustion front. Molecular diffusion and transverse mechanical dispersion will be insufficient to cause all the oxygen in the air stream to reach the combustion front. When the oxygen in the air stream is not completely consumed in the combustion process, it will reach the production well and create a serious fire hazard. In addition, the reduced efficiency may make the process economically unprofitable while also serious corrosion problems may be experienced in the production we11.3 This undesirable situation should, therefore, be prevented. However, in a situation as depicted in Fig. 1, an unstable temperature gradient exists in the gas phase. The combustion is taking place at the lower boundary at a nearly constant temperature that may be anywhere from 600 to 1,200F, depending on the conditions. The upper boundary of the gas phase is overlying, impermeable rock; its temperature might be around 100F, but may increase to 300F or higher due to conduction and convection as the combustion process continues. This represents a steep temperature gradient and it is conceivable that under those conditions free or natural convection will take place in the gas

Jan 1, 1967

By ERIIL SCHROEDTER

THE death, on May 6, 1908, of Dr. Hermann Wedding, Privy Mining Councilor of the Kingdom of Prussia, and Professor of the Metallurgy of Iron and Steel at the Royal Mining Academy of Berlin, was a loss keenly felt by the whole metallurgical world. Not alone in his native land, but also in foreign countries did he enjoy an esteem of which the title of honorary membership in the American Institute of Mining Engineers, the United States Association of Charcoal Iron-Workers, and the (British) Iron and Steel Institute bears eloquent testimony. Hermann Wedding was born March 9, 1834, in Berlin. At the suggestion of Dr. C. J. B. Karsten, the veteran father of Prussian metallurgy and author of the first German text-book of the metallurgy of iron, lie turned his attention, after gradu¬ating from the gymnasium, to mining and metallurgy. In 1853, he began a practical course at the Malapane iron-works, in Upper Silesia. Subsequently, he studied at the Berlin Mining Academy, and received from the University in 1859 the degree of Doctor of Philosophy. A journey which be made to England, somewhat later, led to his undertaking a German translation, with revision and additions, of John Percy's classic treatise on the metallurgy of iron and steel, the publication of which, in successive installments, stretched through many years. In 1863, lie published, as a thesis in connection with his "Assessor's examination," an essay, entitled The Results of the Bessemer Process for the Production of Steel, and Its Prospects for the Rhenish and Westphalian Iron and Steel Industry, which revealed such ability and knowledge as to secure for him a call to the chair of metallurgy in the Berlin Mining Academy.

Jun 1, 1909

By M. Muskat

A theory has been developed describing the behavior of wells and reservoirs producing by the action of bottom water drives. It is assumed that the pressures are maintained above the bubble point, and that the permeability to viscosity ratio of the water in the flooded zone is the same as for the oil in the oil-saturated pay. Accordingly, the treatment is based on the homogeneous fluid potential theory. The effect of the difference in density between the oil and water is neglected. .4fter deriving the proper potential distrihutions, the nature of the rise of the water-oil interface below the producing wells is calculated. The primary clean-oil-production phase is expressed in terms of the displacement efficiency, defined as the fraction of the pay flooded out by the rising water table at tlle time of first water entry. The variation of this displacement efficiency is calculated as a function of the well spacing, pay thickness, the ratio of the horizontal to vertical permeability, and the well penetration. The important parameter, other than the well penetration, is found to be the ratio of the well separation to the thickness of the oil pay multiplied by the square root of the ratio of vertical to horizontal permeability. It was found that the displacement efficiency continually decreases as this parameter increases, and for values of the latter >3.5, the efficiency varies inversely as the square of the parameter. It also increases with decreasing well penetration. Perhaps the most striking result of this phase of the analysis is the conclusion that in order to explain the delay in entry of water in wells producing by bottom water drives for periods longer than a few days normal production, with drawdowns large compared with the differential density head between the oil and water, it is necessary to assume that the vertical permeability is a very low fraction of the horizontal permeability. An analysis is also given of the production history after the water has broken through, on the assumption that the production mechanism and details of the flow distribution continue to be the same as during the phase of clean-oil production. As is to be expected, it is found that the water cut will increase at an accelerated rate as production proceeds. However, the initial differences between systems of different well penetrations or well spacings with respect to the total clean-oil production gradually decrease in terms of the variation of the water-oil ratio with cumulative production. In particular, by the time the water-oil ratio has reached values of the order of 5 or greater the cumulative recoveries will generally differ much less among various producing systems than their corresponding clean-oil recoveries. Introduction On the basis of elementary geological principles, one may classify effective water-drive fields in two groups. In the first, the entry of water into the oil-producing formation may be characterized as an edge-water encroachment. This term is used to suggest that the motion of the water proceeds largely in a direction parallel to the planes of stratification. This type of water intrusion occurs usually in thin producing zones and in strata lying along structural flanks of appreciable dip. In the second group—"bottom water-drive" fields—the water-oil interface lies in a plane of zero or slight inclination to the

Jan 1, 1947

By M. Muskat

A theory has been developed describing the behavior of wells and reservoirs producing by the action of bottom water drives. It is assumed that the pressures are maintained above the bubble point, and that the permeability to viscosity ratio of the water in the flooded zone is the same as for the oil in the oil-saturated pay. Accordingly, the treatment is based on the homogeneous fluid potential theory. The effect of the difference in density between the oil and water is neglected. .4fter deriving the proper potential distrihutions, the nature of the rise of the water-oil interface below the producing wells is calculated. The primary clean-oil-production phase is expressed in terms of the displacement efficiency, defined as the fraction of the pay flooded out by the rising water table at tlle time of first water entry. The variation of this displacement efficiency is calculated as a function of the well spacing, pay thickness, the ratio of the horizontal to vertical permeability, and the well penetration. The important parameter, other than the well penetration, is found to be the ratio of the well separation to the thickness of the oil pay multiplied by the square root of the ratio of vertical to horizontal permeability. It was found that the displacement efficiency continually decreases as this parameter increases, and for values of the latter >3.5, the efficiency varies inversely as the square of the parameter. It also increases with decreasing well penetration. Perhaps the most striking result of this phase of the analysis is the conclusion that in order to explain the delay in entry of water in wells producing by bottom water drives for periods longer than a few days normal production, with drawdowns large compared with the differential density head between the oil and water, it is necessary to assume that the vertical permeability is a very low fraction of the horizontal permeability. An analysis is also given of the production history after the water has broken through, on the assumption that the production mechanism and details of the flow distribution continue to be the same as during the phase of clean-oil production. As is to be expected, it is found that the water cut will increase at an accelerated rate as production proceeds. However, the initial differences between systems of different well penetrations or well spacings with respect to the total clean-oil production gradually decrease in terms of the variation of the water-oil ratio with cumulative production. In particular, by the time the water-oil ratio has reached values of the order of 5 or greater the cumulative recoveries will generally differ much less among various producing systems than their corresponding clean-oil recoveries. Introduction On the basis of elementary geological principles, one may classify effective water-drive fields in two groups. In the first, the entry of water into the oil-producing formation may be characterized as an edge-water encroachment. This term is used to suggest that the motion of the water proceeds largely in a direction parallel to the planes of stratification. This type of water intrusion occurs usually in thin producing zones and in strata lying along structural flanks of appreciable dip. In the second group—"bottom water-drive" fields—the water-oil interface lies in a plane of zero or slight inclination to the

Jan 1, 1947

[¦Abad, Leopoldo F., College of Min., Univ. of California Berkeley, Cal. '23 ¦Abarquez, Ramon F., Met., Bureau of Science Manila, P. 1. '24 ¦Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, Ohio. '21 Abbott, A. N., Mines Supt., Mazapil Copper Co., Ltd ...Concepcion del Oro, Zacatecas, Mexico. '23 Abbott, Clarence B., Gen'l Supt., Iron Mines Div., Tenn. Coal, Iron & R. R. Co., 1405 Minnesota Ave., Bessemer, Ala.' '04] [ ]

Jan 1, 1925

Between July 10 and August 15, 1918, the Secretary of United Engineering Society, of Engineering Foundation, and of Engineering Council visited 17 cities which are headquarters for large numbers of engineers. His mission was to tell men in all branches of the profession about "Centralized Activities of National Engineering Societies." Stops were made at Denver, Salt Lake City, Reno, San Francisco, Sacramento, Portland, Seattle, Spokane, Anaconda, Butte, Duluth,

Jan 10, 1918

By Theodore W. Robinson

WHEREVER the amount of work renders it practicable the plan of using permanent standard solutions, in connection with the colorimetric carbon test, affords such manifold advantages that it is to be strongly recommended. That it has not attained a wider and more general application, is mainly due to the fact that, as the method is generally employed, the difficulty attending the production of the colors, and their doubtful stability when produced, have been only too evident to those who have undertaken their composition. The old method of using standard solutions made from sugar, coffee, etc., has always been hampered by the tendency of the colors to change upon exposure to the light, and the consequent liability to serious error, unless they are closely watched. Appreciating these difficulties, while recognizing the desirability of permanent colors, Mr. Magnus Troilius, at the suggestion of Prof. F. L. Erkmann, investigated the properties of cobalt, copper and ferric chlorides, with the view of determining their efficacy in the production of standard solutions. His results, as obtained, seem to have been satisfactory, but his treatment failed to eliminate many of the objections that have rendered the use of organic colors undesirable. The

Jan 1, 1888

By GEO H. DEIKE

NOT much activity has been evident during the past year in the establishment of co-operative scholarships but the interest among the coal-mining companies is more pronounced than ever. This is apparent from the replies received to a letter sent out by the Committee on the Promotion of Student Interest in Coal Mining to over 120 coalmine operating officials. With that letter was forwarded a bulletin issued by the school of mineral industries of The Pennsylvania State College entitled ?Industrial Scholarships ? a Partnership of Industry and Education.? In that circular was outlined the need for trained men in the war and postwar world, and particularly as such demands pertain to the growth of the mineral industries.

Jan 1, 1943

By D. L., Hayes

THE concentration of zinc ore in Wisconsin is a comparatively simple process, although it presents problems that must be overcome in an efficient manner in such a way that installation and operating costs are low. As the ore deposits are small, the first cost of the concentrating plant must be low; while the low margin of profit makes it necessary to have the minimum operating costs. The original mills were copied from those of the Joplin district, as most of them were built and operated by Joplin millmen. These served the purpose well; they made a clean concentrate, which was the chief requirement at that time, as most 'of the mines were' considerably 'richer than the average at the present time, and wages and supplies were also considerably lower. ' The apparatus used at present has changed very little in principle. . The grizzly opening has gradually been increased to 12 in. and sometimes no grizzly 'is used. The crusher, gradually grew in size, the largest crusher has -an opening of about 24 by 13 in. and a 7/8-in. throw on the. eccentric shaft.

Jan 1, 1921