Search Documents

By E. A. G. Colls

Discusses corrosion in Trail chemical plants producing ammonia, sulphuric, nitric and phosphoric acids, ammonium phosphates, sulphate and nitrate, together with miscellaneous allied material problems and their solution using erosion or corrosion proof materials. Conclusion, that for work of this nature, most costly material may well be cheapest in the long run.

Jan 4, 1950

By P. E. Baker

An experimental study of heat flow in steam flooding was carried out with steam displacing water in a plane-radial fluid-flow model. Temperature distributions in the model reservoir, overburden, and substratum were measured at frequent intervals during flooding by means of a fixed array of thermocouples. Heat losses to overburden and substratum and the division of heat between the steam and hot-water zones in the reservoir were calculated from the temperature data by performing numerical integrations over the appropriate volumes. Temperature profiles and heat distribution results are presented. Some results were (1) the fraction of injected heat that is lost to overburden and substratum, when expressed as a function of time, did not depend on injection rate; (2) a significant portion of the injected heat was contained in the hot-water zone ahead of and underlying the steam front in the reservoir. The division of heat between the steam and hot-water zones did depend on injection rate; and (3) considerable gravity override was observed. The experimental results are compared with those of several published theoretical studies of heat transfer in hot-fluid injection; approximate agreement on heat losses is found with some of the most idealized theories. A valid comparison cannot be made in regard to steam us hot-water zone; basic interpretation of the hot-water zone, in terms of a vertical steam front, is clouded by gravity override in the experiments. INTRODUCTION The experimental study reported here primarily concerns two problems of heat transfer in steam flooding that have economic and engineering importance. These are (1) the fraction of injected heat lost to the overburden and substratum, and (2) the division of the remaining heat between a zone containing steam and a zone of hot water at lower-than-boiling temperature. The volume of the steamed region, which has a direct effect on oil recovery, can be calculated readily from these results. Several valuable theoretical studies have been published on this problem, but no experimental tests of the theories have previously appeared. Tests were needed because the effects of the necessary simplifications in the theories could not be determined otherwise. The basic, untested theoretical problem is the effect of "decoupling" heat and mass transfer, and the resulting inability to include the effects of heat transfer and condensation on fluid flow. The theoretical problem solved so far has been a heat transfer problem in which fluid is present as a heat carrier and flows in a stipulated manner, either linear or plane-radial. The simplifications that have sometimes been made in regard to thermal conductivity by, for example, Marx and Langenheim,l Lauwerier2 and Thomas3 apparently do not have an important effect on heat loss calculations, although the results of the different methods disagree to a certain extent, as shown by Spillette4 and by Ramey.5 A recent paper by the author6 compared the results of experiments in hot-water flooding with several theoretical results and showed a rather poor agreement. It will be seen that the experimental heat loss results for steam flooding, however, show acceptable agreement. These comparisons are discussed in a later section. EXPERIMENTAL APPARATUS AND PROCEDURE The system studied was one in which a sand pack, initially water saturated and at a uniform temperature, was flooded with steam at a constant rate and temperature. The temperature distribution in the "reservoir" and adjacent "strata" was measured with an array of thermocouples, and heat losses were determined from these measurements. The sand pack contained no oil because the only concern of the experiments was heat flow, and it was important to have the flow pattern as simple

Jan 1, 1970

By W. P. Saunders, W. R. Hibbard, G. H. Eichelman

Interest in the various products of the austenite eutectoid transformation in iron-carbon alloys, particularly as produced by the isothermal sub-critical techniques introduced by Davenport and Bain,' has resulted in the application of similar heat treatments to other eutectoid transformations. Studies o f the beta copper-aluminum alloy eutectoid transformation revealed microstructures very similar to those found in iron-carbon alloys. Investigations5t6 of the kappa phase in the copper-silicon alloy system have established the eutectoid type transformation of this phase into terminal alpha and intermediate gamma phases. This transformation has been reported5 as forming a eutectoid type structure in a very sluggish manner by a long time isothermal treatment. The purpose of the present investigation is to study the products of the kappa eutectoid transformation as affected by transformation temperatures by means of microscopic and hardness methods. Preparation of Alloys The copper-silicon alloy equilibrium diagram is shown in Fig 1. The kappa field converges to a minimum silicon solubility at the eutectoid composition and all other completely kappa alloys are hypereutec-toid. Thus, kappa decomposition involves first the proeutectoid precipitation of gamma, followed by the eutectoid transformation of a lower silicon content kappa (5.2 pct) Smith6 has indicated that alloys containing between 5.4 and 5.7 pct silicon could be hot rolled, but that the latter composition was desirable in order to permit a wider kappa temperature range. The alloy was prepared by adding Baker's commercially pure silicon to an ingot of copper-silicon alloy containing 2.34 pct silicon remaining from the investigation of Brick, Martin and Angier.' Following the casting techniques of Krynitsky, Saunders and Stern,s the ingot was melted under a heavy layer of dried charcoal in a clay-graphite crucible in a gas-fired pot furnace. Small lumps of silicon were held under thc melt surface with a graphite rod. After the silicon had dissolved, the alloy was chill-cast and then remelted without a cover, stirred thoroughly, skimmed and poured into a preheated cast iron mold. The cast microstructure is shown in Fig 2. The casting, 10 X 4 X K in., was annealed at 750°C for 21 hr and furnace cooled, About }{& in. was milled from all surfaces. The plate was cut in half longitudinally and the bottom half analyzed by A.S.T.M. and The composition by weight was as follows: copper 94.24 pct, silicon 5.56 pct, iron 0.11 pct.

Jan 1, 1949

By M. Lonoff

Byproducts are more important to the copper mining companies than to the copper market. Copper ores frequently contain gold, silver, molybdenum, lead, zinc, and cobalt. With the increase in the prices of these metals copper mining has become more profitable. If byproduct prices remain high, additional firms will be attracted to the copper industry; the increased supply of copper will reduce the long-run copper price. However, this is unlikely to happen because the markets for the copper byproducts, especially molybdenum and cobalt, are small. Increased recovery from copper and other sources will depress the prices of these byproducts before the copper price is significantly affected. Should byproduct prices remain high, the copper market will both settle at a lower long-run price and be more unstable in the short run. Since changes in the copper price do not affect the entire earnings of a multi-metal mine, the copper price must fall further before such mines reduce output in the short run. Higher byproduct revenues will make copper supply less responsive to copper prices; shifts in copper demand will result in greater copper price fluctuations in the short run than they did before.

Jan 1, 1984

Pumping coal to market may help Appalachian coal operators increase their share of the eastern seaboard fuel business. Transporting it by pipeline is already an accomplished fact, but until recently it had to be dewatered to be used in boiler furnaces. The campaign for these eastern markets was begun in earnest last November by the widely publicized announcement of successful plant-scale firing of a central station boiler with coal slurry pumped to the burners. This latest advance makes coal similar to oil and gas in convenience in handling and controlling at the consumption end of the pipeline. Slurry could be considered a new commodity for the fuel market. HUGE POTENTIAL MARKET The heaviest concentration of power plants in the U.S. is along the line Washington, Baltimore, Philadelphia, New York and Boston which makes this region the best hunting ground for selling pipelined coal brought from western Pennsylvania and northern West Virginia. Furthermore, if this region is assumed to consume 125 million tons of coal annually, on a comparable basis, the consumption of oil and gas would be about 180 million tons. Even if all of this fuel is not consumed in central stations, it is still a very big market for coal at the right price. Consolidation Coal Co. and Texas Eastern Transmission Co. are trying to line up customers in this area so that a pipeline can be built. This is not to say that there are not many other areas in the U.S. that could not be supplied advantageously by a mine-to-market pipeline.

Jan 1, 1962

By Charles M. Cooley

THE continual improvements in. the two extremes of the drilling, unit, the drill and bit, have prompted critical examination of the drill steel, the weak link of this drilling unit. Obviously, little is to be gained from the betterment of the drill and bit if the drill steel which transmits the force needed for drilling from the machine to the bit cannot stand long hard service. The technology of the bit has advanced from the integral type to steel detachables, thence to the tungsten carbide insert. The carbide insert is the most significant advance in the bit, bringing it to the level of a machine tool with its performance records under constant surveillance. Long steel changes have become advantageous because the carbide bit will drill greater footages without replacement than did the steel bit: The development of the tungsten carbide insert opened new fields of endeavor in drilling with percussion drills here- to fore known, but limited by the steel bit. After the introduction of the tungsten carbide bit, drill manufacturers began promotion of long feed shells, lighter drifters and stopers, and easily handled auxiliary equipment. Ultimately this promotion of better equipment was intended to increase the bit-against-rock time of the drill shift. Advantages of the uninterrupted drilling period of a long steel change and faster setup time of lighter drill machines are lost when the shank fails in the machine, rod failure requires continual changing, or the bit breaks off in the hole. The quest for reduced

Jan 1, 1952

As one surveys the extensive taconite operations on the Mesabi Range, he may find it difficult to believe that only 15 years ago, the iron ore mining industry here was staring at its own imminent demise. Due to the high demands for iron ore during World War II the postwar period of 1946-1950, and the subsequent "police action" in Korea, there was rapid consumption of the Mesabi's already depleted ores, and some economists were giving the Range only 20-25 years of life. In the 13-year period 1941-1953, more than 850 million tons of iron ore were shipped to steel mills, an amount almost equal to the total production during the preceding 30 years. Proven ore reserves dropped from 1.1 billion tons in 1940 to 8.3 million tons in 1954, the largest decrease being recorded in the famed direct shipping ores.

Jan 9, 1968

By Richard H. Olson

"Rarely in our technological society does the discovery of a new class of inorganic materials result in such a wide scientific interest and kaleidoscopic development of applications as has happened with the zeolite molecular sieves." The foregoing, the opening sentence in a landmark volume on zeolite molecular sieves by D. W. Breck (1974), is, if anything, an understatement. Zeolites were recognized as a new group of minerals in the 1750s, but it was not until 1930 that the first analysis of the crystal structure of a zeolite mineral was made. In the late 1940s research workers at Union Carbide Corp. began a program of zeolite synthesis and study which has resulted in one of the major research achievements of all time. Naturally, with the vast research and development efforts devoted to the synthetic molecular sieves, Union Carbide became concerned in the mid-1950s about its position should minable deposits of natural analogues be discovered. Zeolite minerals have diverse origins, and even a brief discussion of these is beyond the scope of this paper. The early work on zeolites was confined to igneous rock occurrences (e.g., amygdules and veins) which were formed by "space-filling;" these crystals tend to be euhedral, thereby rendering them appealing to both mineralogists and collectors. During the first year or so of Union Carbide's exploration (which began in mid-1957) attention was devoted solely to such igneous occurrences. A landmark paper by Bramlette and Posnjak (1933) heralded the potential significance of the occurrence of zeolite minerals as alteration products of vitric ash and similar materials. In the summer of 1958, full attention was directed by Union Carbide to the search for deposits of this type in the western United States. Since then, such exploration has been continu-

Jan 1, 1975

By W. E. D. Stokes

THE application of aviation to mining and petroleum operations, on the basis of economy and attainment, has become a demonstrated fact. According to Dominion Government records, 30 Canadian companies engaged in air transportation with northland mining camps, carried 13,000 tons of freight in 1935, and in 1936 carried 16,000 tons. In addition, many mining companies used planes to transport prospectors with canoes, outboard motors, gasoline drums and supplies to remote locations, and one company maintained a plane to take radium-bearing ore from its mine on Great Bear Lake nearly 1000 miles south to the rail- way at Waterways, Alberta. Heavy pieces of mining machinery weighing 2 tons are being carried by Ford trimotor planes over the Andes, at an altitude of not less than 15,000 feet. At Bulolo, New Guinea, 17,500 tons of disassembled gold-dredging equipment has been flown over inaccessible terrain, while supplies and building materials for a community of 1000 whites have been transported by airplane. A 3 1/2-ton shaft was carried on one notable trip, while at another time an automobile, 2 tons of rice and a large safe went over the mountains in one plane. Fig. 1 shows an electric generator that was carried by plane to Bulolo. Many large American oil companies operated fleets of planes during 1936, ranging from fast, luxurious air liners for executives to elaborate geological prospecting units, ambulance planes, freight carriers and pipe-line repair crews. According to the U. S. Geological Survey, commercial firms photographed 16,291 square miles during 1935, while the Government compiled from aerial photographs by the Geological Survey in the United States 85,544 square miles. It was found that information could be determined in a fraction of the time required by surface methods. However, sounding a word of caution, a Commonwealth of Australia government report on aerial survey operations had this to say: It is necessary to repeat ad nauseam that aerial photographic survey is in no sense a substitute for geological investigation, though it is a very valuable adjunct thereto, and greatly facilitates and accelerates geological mapping. There are many details

Jan 1, 1937

By W. R. Crane

While professiorlally engaged in the oil- and gas-fields of Kansas, in measuring the pressure and flow of gas-wells, and studying the phenomena attendant upon the production of both oil and gas, I noticed in the flow of gas a peculiar and interesting feature. That there are actual lines of flow in liquids (non-compressible fluids) discharged through an orifice, or a short section of pipe, is shown by the external shape of the discharge—the vena contracts. Such lines of flow are not observable in the discharge of gas from an orifice. It can hardly be questioned that they exist. That they are not apparent is probably due to the very small weight of the gaseous particles, which climinishes the momentum of their movement in a given direction, acquired before they issue from the orifice, and also to the expansion of the gases, which would exert a powerful influence in overcoming any such tendency in their flow. Gas flowing from an orifice, supplied by a large reservoir or blowing-engine, exhibits almost the reverse of what is noticed with liquids. Namely, the gas assumes the form of an inverted truncated cone, of large angle: with its apex-end at the orifice. (See BB, Fig. 1.) This external ahape assunled by the flow of gas shows, however, marked differences under varying conditions of volume and pressure. For instance, a large volume of gas under high pressure, flowing through a 2- or 3-in. pipe, as in the case of a natural gas-well, assumes a more definite conical form, the angle of which increases as the pressure falls. Moreover, outside of the well-defined inverted cone is a thin conical heath or zone of gas, A A, the angle of which is considerably greater than that of the main cone, and increases with +1UNIVERSITY OF KANSAS, LAWRENCE, KANSAS.

Jan 1, 1905

The following discussion occurred on the afternoon of Sept,. 22, 1930, as part of the fall meeting of the Iron and Steel Division at Chicago. About seventy-five men attended this session. C. B. Murray opened the meeting, as follows: C. B. Murray, Cleveland, Ohio.—It is very encouraging to see so many here this afternoon to discuss this important matter of beneficiation. The producers of ore, I am sure, are anxious to furnish the grade of ore that the consumer wants. The consumer sometimes wants that which cannot be economically produced and often the producer cannot understand why the consumer wants certain things. It was to bring together these two interested parties that this meeting was proposed. I was appointed the chairman of the meeting, chiefly because I happened to be the chairman of the Iron Ore Committee of the Institute. I know a little about iron ore but have not perhaps kept up with the times in blast-furnace practice. I am asking Mr. Sweetser, who is well informed from both sides, to take over the meeting and carry on the discussion. R. H. Sweetser, Columbus, Ohio.—We want to have a free discussion between the iron-ore men and the blast-furnace men as to just what we are trying to reach in the beneficiation of iron ores. Many of those present have had a great deal of experience. There are men here from the ranges who have been passing through the experimental stage of beneficiation of iron ores, and there are some who have already gone on to commercial production. We have reached the point where the beneficiation of iron ore is important to the whole iron and steel industry. The connection between iron-ore beneficiation and the cleaning of coal is so close that I think we can profit by working very close to the coal people. Some Aspects of the Iron-ore Situation W. G. Swart, Babbitt, Minn.—I was very much interested in Mr. Richards'* paper on tonnages and the 20-year life. There is one interesting thing about the ore reserves; that is, the irregular distribution of that tonnage. On the Mesabi Range, for example, the United States Steel Corpn. owns between 70 and 75 per cent. of the reserve tonnage. They ship bctween 40 and 50 per cent. of the annual Lake Superior

Jan 1, 1930

New York, March 18, 1913. MR. CHARLES F. RA ND, President, New YORK, MARCH American Institute of Mining Engineers. Dear Sir: In connection with the official notice of Dr. Raymond's unanimous election by the Directors as Secretary Emeritus, we wish to place upon record certain statements concerning his services to the Institute which we think have not been published., and may not be generally known to the majority of our fellow-members. When the Institute was formed in 1871, Dr. Raymond acted as Secretary of the Founders' Meeting, and became the first Vice-President of the Institute, and, by request of the aged and beloved David Thomas, who was the first President of the Institute, Dr. Raymond discharged all the duties of the office of President, to which he was later formally elected in 1872, and which lip held for three years. During that time, he visited Europe, and through his acquaintance and reputation abroad, established those international relations of the Institute which proved so important in later years. He also enlisted the support of the mining engineers and metallurgists of the Pacific Slope, who would not otherwise have been disposed to join a society originating in the East. And for twelve years he attended; at his own expense, nearly every meeting of the Institute, wherever held, giving to it without remuneration his best service, and sacrificing for it many professional and private interests.

Jan 4, 1913

By D. J. Reed

Concord coal mine near Bessemer, Ala., built, owned, and operated by Tennessee Coal & Iron Div., U. S. Steel Corp., produces only a metallurgical grade for use as coke in blast furnaces of the division at the Fairfield and Ensley works. Capacity of the operation is approximately 800 tph, half of which is delivered to the coke and coal chemical plant at Fairfield after beneficiation to metallurgical grade coal. The remaining portion of the mine run is rock and refuse removed during preparation. Concord mine coal is hoisted to the surface coal preparation plant by an underground slope conveyor. The slope conveyor is 2449 ft long and has a lift of 729 ft. At time of installation the Concord mine slope conveyor was the largest single conveyor unit ever made with respect to belt horsepower and total lift. After several years it became necessary to determine the cause of slope conveyor cover wear.

Nov 1, 1956

By 000-001-568

August 15th, 1871. THE Institute assembled in Packer Hall of the Lehigh University, the President, Mr. David Thomas, of Catasauqua in the chair. Professor Henry Coppée, President of the Lehigh University, made an address of welcome to the Institute, and placed at its disposal a convenient hall for purposes of meeting. Mr. Thomas tendered his resignation as President of the Institute, as advancing years prevented him from actively participating in its meetings. The Institute declined to accept the resignation, and, on the assurance that active duties would not be expected of him, Mr. Thomas was induced to withdraw it. Invitations were received from Mr. B. C. Webster, President of the Lehigh Zinc Company, to visit the mines and works of the company; from Mr. Charles Brodhead, to visit the Chapman Slate Quarries ; and from the Lehigh Coal and Navigation Company, to visit their works at Summit Hill and Mauch Chunk and the Nesquehoning Tunnel. The Council reported the names of persons already elected in the two classes of members and associates. The following resolutions were passed: Resolved, That a committee of three be appointed, who shall take into consideration the printing and publishing of papers originating with the Institute, and that a uniform system as regards size and execution be adopted. The committee appointed consisted of Messrs. R. W. Raymond, E. B. Coxe, and the Secretary. Resolved, That the Council design and prepare a seal for the Institute at the earliest practicable time. Resolved, That a committee of six, with power to add to its numbers, be appointed to examine into the question of the more economical production of iron in this country. The committee appointed consisted of Messrs. G. W. Maynard,

Jan 1, 1873

By Jacques B. Wertz

Detailed structural studies in southeast Arizona have successively revealed (1) the local attitudes of individual fractures (with lateral and/or vertical displacements), (2) the patterns exhibited by groups of fractures, and (3) the trends and directions shown by fracture groups or zones on a regional scale. The results of the studies have been twofold: First, domes were locally determined from these fracture arrangements, even where other criteria failed; and, second, fundamental breaks brought out the breadth of the Texas lineament in southeast Arizona as well as major northwest- and northeast-trending fracture zones. Coincidence of one or several domes with the major intersections of fundamental breaks can be centers of important mineralization, as in the instances of Bisbee, Ajo and Morenci. THE OVER-ALL STRUCTURE OF ARIZONA A northwest-southeast trending anticlinorium has been suggested as the structural setting of Arizona. Starting in Triassic and culminating in late Cretaceous times, this deformation resulted from stresses of considerable magnitude with varying ratios of com pres sional and uplifting forces. However, the series of parallel flexures could just as well have been caused by isostatic movements involving dilation under tension with only incidental compression, as later emphasized by dike filling and block faulting (Fig. 1). The anticlinorial deformation, which is also suggested by the fact that the Pre-cambrian rocks to the southwest are all concealed by sediments, could be somewhat reminiscent of the conditions that affected the classical swarm of parallel dikes of wager.' ANALYSlS OF DATA As a first step in this analysis, all structural information obtained on such features as fractures and their relative displacements, faults, dikes, anticlines, synclines, and Precambrian and Laramide-Tertiary intrusives were plotted on maps along with structural trends inferred from aerial photographic mosaics. Next, the faults in southwest Arizona were classified according to time of occurrence and relative importance. The fault assemblages were then examined as to geometric or spatial arrangement and correlated with the occurrences of domes and existing Finally, the conjunction of fracture intersections and domes was analyzed and compared with locations of known ore deposits. Differentiation of Faults According to Time and Relative Importance: The faults encountered were grouped as follows: (1) Basin and Range faults, latest in time; (2) secondary faults; (3) primary faults; and (4) lineaments, earliest in time by inference. BASIN AND RANGE FAULTS- Generally concealed by alluvium, the Basin and Range faults are normal

Jan 1, 1969

By Albert Smith

THE creep properties of metals have as-sumed increasing importance in recent years and many investigations have been made on various phases of the problem. In the past year the annual lectures of the Insti-tute of Metals Division1 and the Iron and Steel Division2 were concerned with this subject, and are excellent reviews. For many years the creep properties of lead and lead alloys have been investigated at the Central Research Laboratories of the American Smelting and Refining Co., and it is hoped that the present paper will contribute knowledge of some of the factors that influ-ence creep. Lead, being a metal that recrys-tallizes readily at room temperature, is an excellent material upon which to investi-gate creep phenomena because of the sim-plicity of the apparatus needed, and it might be expected that results would apply to some extent to elevated-temperature tests of other metals.

Jan 1, 1940

By Ballard H. Clemmons

THE future of the steelmaking industry of the Birmingham, Ala., district is closely related to and, in a large measure, dependent on the development of workable, economic processes of ore concentration. Operations thus far in the area have been possible only because of the fortuitous occurrence of iron ore, fluxing stone, and coking coal-all the primary iron-making materials- within a 25-mile radius of the blast furnaces. Commercial ore of the district consists mainly of a 10 to 20-ft hematite-calcite-silica bed locally known as the "Big Seam," a component of the Clinton formation of Silurian Age. At present mining rates, this ore will be available for a number of years. It is largely mined under 1000 to 2000 ft of cover and transported on 15 to 20" slopes that, in some instances, are as much as 10,000 ft long. Under these conditions, particularly with increasing distances from face to portal, mining costs are gradually becoming disproportionately high. Although not a major factor thus far, it should also be noted that the average annual ore output of the district is gradually be- coming more siliceous.

Jan 1, 1950

By D. S. Sanders

IN the four mills of the Cerro de Pasco Copper Corp. in Peru, some 3000 tons of complex sulphide ores are treated daily, with four kinds of concentrates produced: copper, lead, zinc, and pyrite, each containing values in silver, gold, bismuth, and some other metals. Copper occurs in the various ores as chalcopyrite, enargite, tetrahedrite, tenantite, bournonite, and chalcocite; lead as galena; and zinc as sphalerite and marmatite. Small amounts of silver and tungsten minerals are also present. The gangue consist mainly of shale, quartzite, calcite, rhodochrosite, pyrite, and pyrrhotite. In general the values are freed with a relatively coarse grind, about 70 prr cent minus 200 mesh being the finest to which the pulps are ground. In Morococha and Casapalca however. sphalerite particles much finer than this contain inclusions of chalcopyrit r. At Cerro de Pasco the silver and gold are present in all sizes of the ground pyrite.

Jan 1, 1945

By AIME AIME

MEMBERS of the Engineering Education Committee held two meetings at Joplin preliminary to the opening of the main meeting there. The first was held on Sunday afternoon. It was attended by all who had arrived early enough and as among the dozen or' fifteen who were present the heads of a half dozen schools of mines were included it was a representative gathering. C: H. Fulton, chairman of the Committee presided and T. T. Read acted as secretary of the meeting. The chair., man reminded those present that last year there had been some discussion as to the advisability of the proposal, made by Edward Steidle, that a, separate society, devoted to education in the mineral industry, he organized. Many .people had felt that there are already so many societies in existence to demand one's time and attention, that it would be a mistake to add to their number and the counter suggestion had been made that the work of this committee could be so reorganized as to meet all the needs that a separate society could fill. He therefore presented for discussion these four' questions: (1) Shall a subcommittee .be appointed to study, and report in February, 1932, the possibility of the reorganization of the work of the Engineering Education Committee into the equivalent of an' Institute division; (2) if the work is so reorganized what shall be the relation of the work of the Committee (division) to the work of the-Society for the Promotion of Engineering Education; (3.): what are the, cardinal objectives of education for the mineral industry; and (4) what should be done as regards the movement in some institutions to plan their work-in the light of that being done in other institutions, for example, in geophysics?

Jan 1, 1931

By A. S. Richardson

THE conditions that make necessary the mechanical ventilation of the Butte mines of the Anaconda Copper Mining Co. are due to a number of causes, all of which are incidental to the depth at which mining operations are now carried on. The main object to be accomplished, of course, is the reduction of the temperature and humidity of the air in the working places. Ventilation fans, both surface and underground, have been used for many years, but increasing depth has made the problem much more difficult. Further improvement in both ventilation equipment and methods, therefore, became necessary; and it is the purpose of this paper to describe the work planned and done under the improvement program. The mines of the district have been frequently described in various technical publications, so a description is unnecessary here. From a mine-ventilation viewpoint, compared with coal-mine ventilation systems, the problem is complicated by the fact that the workings to be ventilated are situated on a large number of steeply dipping veins which frequently intersect and are faulted, and also by the fact that the extent, or existence, of orebodies is not definitely known in advance of actual development work. For these reasons ventilation work cannot be planned in advance of actual operations, nor can such regular systems of ventilation as are used in working the more uniform and continuous bodies of coal be developed. When operations are conducted at a normal rate, about 10,000 miners are employed on two shifts, so that about 5000 men will be underground at one time. But as ventilation is necessary to reduce high temperature and humidity due, mainly, to natural causes, the quantity of air per man per minute is not a governing consideration in determining ventilation requirements. Most important among the numerous sources of heat and humidity in the mines are : heat generated during decay of mine timber; heat and humidity given off by mine rock and water; heat generated by oxidation of sulfide minerals; heat given off by electrical equipment; heat generated by mine fires (in certain localities).

Jan 2, 1922