Search Documents

By M. J. Sinnott

WITH the advent of nodular iron as an engineering material, considerable interest has been shown in developing this material for various applications. Generally the strength, hardness, or ductility are the more common properties used for design purposes but occasionally applications involving a knowledge of the thermal conductivity of the material is required. A search of the literature showed, rather surprisingly, that relatively little work has been done on this property for all types of cast iron. Insufficient data are available on thermal and electrical conductivities to develop the Weidemann-Franz ratio, or the Lorentz relationship, for estimation purposes. There are no data on nodular irons and the published data on malleable irons are quite sketchy. For these reasons the conductivity of the group of nodular irons listed in Table I were measured. Irons I to IV were made in such a fashion as to maintain the carbon and alloy content essentially the same while varying the silicon content. Test specimens were cut from the mid-section of 4-in. keel castings. Iron V is a commercial casting of nodular iron. The test specimen of this iron was cut from the center of a large cast billet 3x10x26 in. All alloys were tested in the as-cast condition. A microstructural examination showed that each iron had spheroidal graphite but the size and distribution varied with the silicon content of the iron. The spheroid size decreased while the number of graphite nodules increased as the silicon content of the iron was increased. The matrix structures of each iron consisted of pearlite and ferrite with the proportions varying from predominantly pearlite in the low-silicon iron to mostly ferrite in the high-silicon iron. The commercial heat, iron V, was predominantly pearlite probably because of its higher manganese and phosphorus content. Two methods for measuring the thermal conductivity were used. The first was a modification of the techniques described by Powell and Hickman and Van Dusen and Shelton,² the second method was a simpler technique described by Jakob and Hawkins." Since the agreement of both methods as tested on two sets of duplicate samples was excellent, the simpler experimental technique was used. The results of the measurements are given in Table II along with a summary of the microstructural constituents. These conductivity data indicate that as the percentage of silicon increases there is a corresponding decrease in the thermal conductivity even though the structure is changing from pearlitic to ferritic. Such a change in microstructure is usually accompanied by an increase in conductivity. A third factor involved in the behavior of these irons is the size and distribution of the graphite nodules. The relative amounts of graphite do not change greatly but the size and distribution do. Generally graphite improves the conductivity but in the present case such an effect is probably masked by the alloying effect from the silicon and its dispersion through the matrix. The thermal conductivity of the nodular irons studied is less than that of regular foundry irons by some 10 to 30 pct and is less than that of regular malleable irons.' The cause of the decreased conductivity is probably the more highly alloyed fer-rites obtained in these irons and the changed mode of distribution of the graphite as compared to the regular foundry irons. References R. W. Powell and M. J. Hickman: Journal Iron and Steel Inst. (1946) 154, No. 2, p. 99. 'M. S. Van Dusen and S. M. Shelton: U. S. Bur. Standards Journal of Research, RP668 (1934) 12, p. 429. ³M. Jakob and G. A. Hawkins: Elements of Heat Transfer and Insulation. 2nd Ed. (1950) New York. John Wiley and Sons. ' J. W. Donaldson: Journal Iron and Steel Inst. (1933) 128, No. 2, p. 255.

Jan 1, 1954

By Donald L. Katz

FIFTEEN years ago Dr. Manning published a paper in "Petroleum Development and Technology" on '.Fundamental Research Relating to Petroleum." He tabulated for several industries "the proportion of their present success which can be fairly attributed to the application of information and processes obtained by scientific research," giving petroleum a score of 7 compared to 100 for the electrical and coal-tar industries. Today the petroleum industry as a whole and the producing groups both have raised their score beyond the majority and are climbing toward the top. Present practices are being developed both by fundamental research and the application of the research method in field operation.

Jan 1, 1941

By M. D. Curran

AS applied to coal, the term processing is subject to many interpretations. To some it means preparation of coal for the market by mechanical means such as crushing, sizing, washing, or treating with oil or chemicals to eliminate dust or improve combustion quality. To others it means conversion of the coal to other commodities as in carbonization to produce coke and by- products, or to liquids by application of the hydrogenation process. I prefer to classify the various forms of mechanical treatment under the heading of beneficiation and apply the term processing to those methods of treatment that destroy the coal sub- stance through distillation or hydrogenation.

Jan 1, 1939

By S. W. MEALS

TWENTY million people in this country and Canada in nearly four million homes can give thanks to our Creator for natural gas, that most wonderful natural fuel with which Dame Nature has so bountifully blessed us. It is a clean, healthy and cheerful fuel, made up almost entirely of carbon and hydrogen. There is no residue, no waste and there are no objectionable constituents; an ideal fuel for the home. It operates like magic, open the valve and it is there for your needs, winter or summer, night or day. You are not required to place your order 30 to 90 days in advance and you do not need to pay for your winter's supply in advance. No ashes to worry about, no flues or chimneys to clean, nor kindling wood to store or bother the housekeeper. We who have been so blessed do not realize what it would mean to be without it. If in place of opening a valve we had to go to the woodshed or coalhouse and then build our fire-carry out the ashes-well, some of us I am afraid would be late reaching our offices and perhaps would miss our hot cakes for breakfast. One cubic foot of gas produced from the White Sand formation contains 1130 B.t.u. and weighs 47/1000 lb.; there are about 24,000 B.t.u. in 1 lb. of gas. Temperatures of over 3400 deg. Fahr. have been obtained with natural gas. Not only is it a superior fuel for the home but it has no equal for use in many large manufacturing industries, especially with the making of glass, pottery and open-hearth steel. In an open-hearth furnace, properly constructed, 5000 cu. ft. will melt one ton of steel. It requires 1/3 ton of bituminous coal gasified in a producer to do the same work, or about 40 gal. of tar or fuel oil, or 11,000 cu. ft. of by-product gas.

Jan 1, 1926

By Mäkinen, Eero

OUTOKUMPU, a large copper mine in eastern Finland, has the distinction of being one of the few important mines in the world discovered by a geologist the late Otto Triistedt, of the Geological Sur- vey of Finland, having found the out- clop in 1910 by tracing glacial ore boulders, some of which had been carried as far as fifty kilometres. As the mine had no connection with either railways or waterways and the possibilities of transport were poor, the owners first tried the Hybinette hydrometallurgical process to extract the copper. The raw ore was finely crushed, treated by a sulphatizing roast. and then leached. The resulting solution was electrolyzed, using lead anodes. This experimental plant, having a capacity of 10,000 tons (all Ions are metric tons in this paper) of raw ore and producing 300 to LEO0 tons of electrolytic copper annually, was built in 1913 and run until dis-

Jan 1, 1938

By W. J. Millard

VAGUE rumors and stories have been heard, from time to time, about the diamond and gold deposits of southern Venezuela. It is perhaps appropriate, at this time of revived interest in gold mining, to publish a few facts in regard to this country, which has been undergoing exploration since the fifteenth century. Gold and diamonds are found principally in the State of Bolivar which lies in southeastern Venezuela and is bounded by British Guiana on the east and Brazil on the south (see Fig. 1). The famous Mt. Roraima is situated at a point where these three countries meet in a common point (see Fig. 2). Some gold is also found in the southern part of the territory of Amacuro. Good oil prospects exist in the northern part of this same territory. Diamonds are found on the Caroni river from Rio Paragua to the village of Guri. Another small district is on the headwaters of the Cuyuni river. Quartz veins containing gold are chiefly exploited in

Jan 1, 1931

By Charles H. White

METHODS in colorimetry are based on the assumption that the intensity of the color of a definite volume of solution is directly proportional to the quantity of the color-producing substance' present. In the preparation and examination of colored solutions there are three ways in which the depth of color may be varied. These variables are; (1) the quantity of the coloring matter, (2) the quantity of the solvent, or the dilution, and (3) the thickness or depth of that portion of the solution examined. With these three variables as a basis, three general methods in colorimetry have been devised, all of which have been used in the determination of carbon in steel. In the first method, the quantity of the solution is kept the same for both the unknown steel and the standard, and the sections compared are of equal thickness, while the quantity of the standard is varied until the color obtained is of the same intensity as that produced by a definite quantity of the unknown steel. In laboratories where this method is used there is pre¬pared and kept for permanent use a series of solutions with varying amounts of the standard, representing the percentages of carbon from the lowest to the highest demanded in that laboratory. These standard solutions are kept in bottles, or test-tubes of equal diameter, and are arranged in series from the faintest to the most intense color, so that it is a simple matter to find the place of the unknown steel in the series, when the solution is of a definite volume and is contained in a tube of the same diameter as the standard tubes. In the second method, equal quantities of the standard and of the unknown steel are dissolved, the standard is diluted to a definite volume, and the solution of the unknown steel is di-

Sep 1, 1906

By Wilbur C. Helt

The United States is self-sufficient in bituminous coal and lignite resources to meet the high range of energy demands forecast for the remainder of this century and beyond. The known or proved recoverable reserves of energy from coal in the United States are estimated to be 88% of all fuel reserves, whereas the energy reserves for oil are estimated to be 276, gas 376, shale oil 5% and uranium 2% (as now used). The demand for all forms of energy used in the United States is increasing at a rate of 3% to 4% per year. Presently, coal is competitive on a supply and cost basis with other fuels in conversion to electrical energy and as a source of energy for converting raw minerals to metals and nonmetals, but it is not competitive in transportation and other uses that demand the high flexibility that oil and gas enjoy because of their form. Coal conversion to fluid forms is essential to make it interchangeable with gas and oil to meet the markets they now occupy. Essentially, the chemical constituents that make up coal are the same hydrocarbons that make up oil and gas; it is a matter of reconstituting the proportions of hydrocarbons to make coal interchangeable with the other fuels. The production of coal has fluctuated widely between the peak production of 631 million tons in 1947 to a low of 403 million tons in 1961. Throughout this period, the total value of the production, f.o.b. mines, has averaged more than $2 billion annually. Beginning with 1962, there has been a steady upward trend in coal production with only minor fluctuations that were mainly caused by labor disputes. Output for the latest typical year, 1970, was 588 million tons. Production in 1971 was affected by a major strike and dropped to 548 million tons. Exports of coal from United States to foreign countries have increased steadily and developed into a substantial annual market for over 71 million tons per year. About 56 million tons of this is suitable for metallurgical purposes, and the remaining 15 million tons is exported for electric power generation. The largest single-industry demand for coal is in the electric generating industry, Fig.1. Roughly, the production of electricity has doubled every

Jan 1, 1973

By Charles H. Morgan

THE case of Henry Cort comprises: (1) the nature of Cort's inventions;, (2) their value to England and to mankind,; (3) the remuneration received therefor by him or his family; and (4) the suitable permanent record and recognition of his services by the representatives of the art lie founded-a debt long over-due, and still unpaid. I. CORT'S INVENTIONS. Under this head, it is unnecessary here to enter into details. The facts have been repeatedly published, and a brief outline of them will be sufficient for my present purpose. . Henry Cort, born in 1740 at Lancaster, England, became a navy broker in. London about 1765, and gained from that business in about ten years. something more than £20,000, which lie devoted to perfecting the manufacture of iron, building a mill at Fontley, near Portsmouth, and prosecuting, between 1777 and 1783, the experiments which culminated in .his two patents, one for puddling iron and the other for shaping it by rolling between grooved rolls.: Careful study of the contemporary evidence, including Cort's specifications, the testimony (in act as well as word) of his business rivals, the public declarations of eminent authorities, and the history of the times, leaves no possible doubt that Cort was the real inventor, of

Mar 1, 1905

By A. L. Jr. Pozzi, A. O. Garder, D. W. Peaceman

A new numerical method is proposed for the solution of multidimensional miscible displacement problems. Besides the usual stationary grid associated with numerical procedures, the method uses moving points for which positions and concentrations are computed each time step. Based on the method of characteristics for treating combined transport and dispersion, the method applies equally well to any number of dimensions and, in contrast with other numerical procedures, properly takes into account the physical dispersion, no matter how small. Extensive tests show that accurate solutions of one-dimensional problems can be obtained over a wide range of values of the dispersion coefficient, including zero. They also show that the moving points do not need to be uniformly spaced, and that increasing the number of moving points beyond 2/grid interval does not significantly improve the accuracy of the solution. Two-dimmsional calculations using the new method were carried out to simulate laboratory model displacements in which gravity caused overriding of solvent. Good agreement between observed and computed profiles and measured and computed concentrations of produced fluid was obtained for a viscosity ratio of 1.89; at higher viscosity ratios, fair agreement was obtained Computed results were found to be significantly affected by vertical dispersion, and negligibly affected by dispersion in the direction of flow, in agreement with conclusions based on experimental observations. INTRODUCTION Although miscible displacement processes are potentially of great economic significance, limited progress has been made in developing mathematical methods for predicting the outcome of a solvent flood. Because of the complexity of the partial differential equations which describe multidimensional miscible displacement, numerical methods are a natural approach to their solution. The task of finding suitable numerical approximations to one of the partial differential equations, which involves both dispersion and convective transport, has been particularly difficult. Dispersion in the absence of transport is described by the heat flow equation, a second-order equation of parabolic type. This equation has been very successfully treated by numerical methods. Transport in the absence of dispersion is described by a first-order equation of hyperbolic type. This equation has been treated numerically with some success in one dimension, both by Lagrangian and Eulerian techniques, 1.2 but extension to two or more dimensions has not been satisfactorily accomplished. Usually one of two things happens: either the numerical solution develops oscillations or it becomes smeared by artificial dispersion resulting from the numerical process. When transport and dispersion are considered simultaneously, this numerical dispersion may dominate the low physical dispersivicy that generally characterizes miscible displacement. Stone and Brian2 have developed a new difference equation for treating combined transport and dispersion in one dimension. By suitable choice of certain parameters, they succeeded in markedly reducing both oscillation and numerical dispersion. However, a satisfactory extension to higher dimensions has not yet been found. Peaceman and Rachford3 presented a centered-in-time and centered-in-distance difference equation combined with a 1,transfer of overshoot" procedure which was demonstrated to work well in one dimension. The technique was applied to the two-dimensional miscible displacement problem, but subsequent calculations with zero dispersivity showed little change in results compared with the calculations they presented. This indicates that their method involved a numerical dispersion of the same order as the physical dispersion. The present paper describes an alternate method for solving the combined transport-dispersion

Jan 1, 1965

By Philip D. Wilson

SPEED is essentiaI in this war program and it is hard to keep up with developments. When the title of this paper was chosen, the contemplated magnesium production for which plants were then under construction was some 200,000 tons of metal per year or sixty times the 3350-ton production in prewar 1939. A few- days later an analysis of the President's 185,000-plane pro-gram, incendiary bomb schedules, and the additional requirements of the Army. Navy and Maritime Commission made it apparent that a much greater amount of magnesium must be provided in 1943. The new figures are huge but the censor will not per-mit their disclosure.

Jan 1, 1942

By J. W. Hickman, E. A. Gulbransen

One of the important factors that determine the resistance of a metal or alloy to further chemical reaction is the structure of the superficial oxide film. A thorough understanding of the physical and chemical structure as well as the stability of the oxide film formed on the surface as a function of time and temperature of the chemical reaction might furnish clues as to the nature of the reaction process and the protective nature of the film. A comprehensive program has been undertaken to study these phenomena. This paper summarizes the structure of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper at temperatures up to 700°C. Before the introduction of the electron diffraction technique, it was necessary to use either direct chemical analyses or X-rav diffraction analyses to determine the nature of the oxide film formed on the metal or alloy. Chemical analyses yields information on the percentages of the several atomic species present in the film while X-ray diffraction analyses yield information on the atomic geometry. In special cases the information obtained may be identical, but in general both viewpoints are necessary. Much of the early work was carried out on the oxidation of bulk samples where thick films were obtained. The products were identified after cooling to room temperature by X-ray diffraction and chemical analyses. Although much useful information has been obtained in this manner. little could be learned about the character of the protective oxides during the period when the films were actually protective. Evidence concerning the chemical structure of thin oxide films has been made possible by the development of the electron diffraction reflection technique. In this method the most fruitful investigations have been made by carrying out the reaction in situ at the temperature at which the film is actually protective. Literature The oxidation of iron has been extensively investigated by X-ray and electron diffraction. Jackson and Quarrelll found that oxide films formed and examined at the same temperature differed considerably from those allowed to cool to room temperature. The results showed that below 400°C the oxide that was stable in intimate contact with iron was Fe³O4; between 515° and 900°C. the stable film was FeO. Above the upper change point of iron the oxide was found to be Fe³O4. From 400' to 515°C., FeO, Fe³O4 or a mixture of the two oxides was found. Recrystallization of the air-formed film below 400' and above 900°C. led to the formation of Fe3O4. In the range where thicker films consisted of FeO, the air-formed film was converted to a new hexagonal oxide not previously described.

Jan 1, 1947

By E. A. Gulbransen, J. W. Hickman

One of the important factors that determine the resistance of a metal or alloy to further chemical reaction is the structure of the superficial oxide film. A thorough understanding of the physical and chemical structure as well as the stability of the oxide film formed on the surface as a function of time and temperature of the chemical reaction might furnish clues as to the nature of the reaction process and the protective nature of the film. A comprehensive program has been undertaken to study these phenomena. This paper summarizes the structure of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper at temperatures up to 700°C. Before the introduction of the electron diffraction technique, it was necessary to use either direct chemical analyses or X-rav diffraction analyses to determine the nature of the oxide film formed on the metal or alloy. Chemical analyses yields information on the percentages of the several atomic species present in the film while X-ray diffraction analyses yield information on the atomic geometry. In special cases the information obtained may be identical, but in general both viewpoints are necessary. Much of the early work was carried out on the oxidation of bulk samples where thick films were obtained. The products were identified after cooling to room temperature by X-ray diffraction and chemical analyses. Although much useful information has been obtained in this manner. little could be learned about the character of the protective oxides during the period when the films were actually protective. Evidence concerning the chemical structure of thin oxide films has been made possible by the development of the electron diffraction reflection technique. In this method the most fruitful investigations have been made by carrying out the reaction in situ at the temperature at which the film is actually protective. Literature The oxidation of iron has been extensively investigated by X-ray and electron diffraction. Jackson and Quarrelll found that oxide films formed and examined at the same temperature differed considerably from those allowed to cool to room temperature. The results showed that below 400°C the oxide that was stable in intimate contact with iron was Fe³O4; between 515° and 900°C. the stable film was FeO. Above the upper change point of iron the oxide was found to be Fe³O4. From 400' to 515°C., FeO, Fe³O4 or a mixture of the two oxides was found. Recrystallization of the air-formed film below 400' and above 900°C. led to the formation of Fe3O4. In the range where thicker films consisted of FeO, the air-formed film was converted to a new hexagonal oxide not previously described.

Jan 1, 1947

By Thomas T., Read

IN this survey of the progressive development (of education for the mineral industries throughout the United States, the review of .the history of each school has usually been completed wherever it is first mentioned, but the history of the schools in the cities of the eastern seaboard was not carried beyond 1870. It is necessary now to cover what happened during the period of approximately the last quarter of the nineteenth century in several of the schools in the east. Philadelphia Of Philadelphia, it has been related in chapter 4 that the Polytechnic College of Pennsylvania began offering a curriculum leading to the B.S. in mining in 1853; that the school did not prosper, and finally closed about 1890. The establishment of a Department of Mining, Arts, and Manufactures at the University of Pennsylvania in 1855-56 was also mentioned, but its history was not carried beyond 1860. In 1859 J. Peter Lesley was appointed professor of mining in the University of Pennsylvania. The son of a cabinetmaker, born in Philadelphia Sept. 17, 1819, he had taken his A.B. degree at the University of Pennsylvania in 1838 and then secured a position on the Geological Survey of Pennsylvania under H. D. Rogers. When the Survey was discontinued, in 1841, he went to Princeton to study theology, was ordained a Presbyterian minister and followed that career until 1852, when the Pennsylvania, Geological Survey was again started and he rejoined its staff. He published "A Manual of Coal and its Topography" in 1856, and studied at the École des Mines, Paris, in 1856-57. He published an 800-page "Iron Manufactures Guide" the year that he was appointed to the staff at the University of Pennsylvania. In 1863-64 a College of Agriculture, Mines, Arts and the Mechanic Arts was established, but it was not a separate school

Jan 1, 1941

By John H. Hall

The Frémont test for measuring the energy consumed in breaking a notched bar of steel is not so well known in this country as it deserves to be. The test specimen used in this test is about # by 6 by about 16 in., notched with a hack saw on the lower side to cause the piece to break at a fixed point. A weight of 10 kg. falling 4 m., and provided with a knife or chisel which strikes the specimen, breaks the test piece by impact. The residual force in the falling weight after it has broken the specimen is recorded by a suitable device, and the difference between the total energy and the residual energy of the weight (in kilogrammeters) is the force consumed in breaking the specimen. An experience of several years with the Frémont testing machine has shown its great value in readily detecting brittleness not revealed by tensile testing or slow bending testing. In this paper it is proposed to discuss (1) the supersensitiveness of the test as applied to cast steel and (2) its value in revealing the effect of heat treatment under certain conditions. In testing coupons cut from castings heat treated by quenching and annealing, attention was drawn to the wide variations in the value of the Frémont test of specimens cut from different parts of the coupon. The latter was of the form and dimensions shown in Fig. 1, and Fremont test pieces were cut from two parts of this coupon, marked A and B in that figure. The results of the tests are shown below, tests A and B in each instance being from the same coupon: A. B. A. B. Coupon. Kilogram- Kilogram- Coupon. Kilogram- Kilogram- meters. meters. meters. meters. 1,........ 12.0 12.5 9,........ 27.5 32.5 2,........ 11.0 32.5 10,........17.5 31.0 3,........ 11.5 30.0 11,........ 14.5 31.0 4,........ 20.0 33.0 12,........ 15.0 27.5 5,........ 17.5 33.0 13,........ 19.0 30.0 6,........ 17.5 20.0 14,........ 17.5 25.5 7,........ 17.5 13.0 15,........15.0 30.0 8,........ 10.0 30.0

Jan 1, 1914

By Beall, John V.

THIS is not simply the story of how a water filled shaft was developed into a million-ton- a-year producing mine in the space of four critical years, although it is reason enough for telling it, but it is also the saga of an engineering achievement in which knowledge nurtured by years of experience in coal and ore mines was blended together and the best from each type of mining selected. The entire system of mining was detailed on maps by the mining engineering department before the shaft was unwatered, and subsequent development followed these plans nearly to perfection. The selection of machinery was particularly critical as it was necessary to push production from only a few headings in the early stages of development and metal mine machinery was being used in a coal panel-system of mining. At the start of World War I1 the demand for iron ore to supply Woodward blast furnaces, and rapid exhaustion of the main source of Wood- ward ore, No. 3 Red Ore mine, necessitated speedy opening of the Pyne mine. The mine is three miles southwest of Bessemer and is responsible for 80 pct of Woodward ore, the rest coming from the Songo mine. The Woodward Iron Co. is one of the old producers of the Birmingham district. S. H. Woodward, an iron-master of Wheeling, overheard two Union soldiers conversing about ore and coal lands in Alabama, which lead to the acquisition of the first ore lands of the Woodward Co. in 1869. Development was not begun until after the death of S. H. Woodward; his two sons, W. H. Woodward and J. H. Woodward, formed the Woodward Iron Co. in 1881 and purchased a tract of land midway between the ore vein on the southeast and the coal field on the northeast about 12 miles southeast of Birmingham for the

Jan 1, 1950

By E. J. Whittenberger

OVER the past two decades, the Cr-Ni stainless steels, popularly termed 18-8 steels, have been used in ever increasing amounts in the aircraft, automotive, chemical, transportation, and building industries.' The contribution of nickel to these steels is associated with its strong austenite forming tendencies which assure good hot and cold forming characteristics, and with its beneficial influence upon corrosion resistance, especially in oxidizing acids. The adjustment of the chromium and nickel contents has been used advantageously in controlling the rollability and the response of the mechanical properties of these steels to cold reduction. With the advent of the jet age and the government stockpiling of nickel, considerable emphasis has been placed upon the development of satisfactory low nickel or nickel-free substitute austenitic stainless steels, especially for nonmilitary applications.2 Fer-ritic 17 pct Cr (AISI Type 430) stainless steel has been effectively substituted for the austenitic grades in applications with mildly corrosive exposure. However, the limited formability and ferromagnetic behavior of this grade do not permit its satisfactory use for many applications. To achieve better formability in a nenmagnetic steel and conserve nickel, a number of low nickel substitute austenitic grades of stainless steel have been developed in recent years. In most of these steels, manganese and nitrogen have been substituted for a portion of the nickel content, for example, 17 pct Cr-4 pct Ni-6 pct Mn (AISI Type 201), 18 pct Cr-5 pct Ni-8 pct Mn (AISI Type 202), and 16 pct Cr-1 pct Ni-17 pct Mn, all of which contain approximately 0.15 pct N.1 The precipitation of ferrite when large ingots of these Cr-Ni-Mn-N steels are heated to temperatures high enough for conversion to slabs on conventional universal slabbing mills has seriously affected the hot workability of these steels. This has been especially true in the case of the 16 pct Cr-1 pct Ni-17 pct Mn (sometimes referred to as 15 pct Cr-1 pct Ni-15 pct Mn) composition." Because it is possible that little, if any, nickel will be available for nonmilitary stainless steel applications in the event of a national emergency, a need has existed for a nickel-free austenitic stainless steel containing hot and cold forming characteristics similar to 18-8 steels and corrosion resistance at least comparable to the 17 pct Cr ferritic steel. The aforementioned deleterious effect of ferrite upon the hot working characteristics of the 16 pct Cr-1 pct Ni-17 pct Mn, steel indicates the importance of establishing the austenite-austenite plus ferrite phase boundaries as the first step in the development of nickel-free or low nickel substitute steels. This paper presents the data collected in an elevated temperature constitutional study of the Cr-Ni-Mn-N system at the South Works of the United States Steel Corp. Experimental Procedure The 300 compositions used in the investigation were melted in a 26 Ib induction furnace and cast in 3 14 in. diam by 18 in tall hot-tcpped ingot mo1ds.

Jan 1, 1958

By R. G. Hudson, H. W. Paxton

The activities of iron and chromium in their binary system have been measured by the Knudsen orifice technique. The system is close to ideal at 1200- 1250 C with slight positive deviations. The effect of this on the liquidus and solidus is discussed and these are calculated for two limiting assumptions. The vapor pressure of pure iron, pure chromium, and one alloy is compared with that obtained by the Langmuir free-evaporation technique. The results agree, indicating a vaporization coefficient close to 1. HERE are no reported data on the thermody-A namic activity of iron and chromium in the solid portions of the phase diagram. It is generally assumed'.' that the liquid solutions of iron and chromium obey Raoult's law. Chen and Chipman" have inferred that the liquid solution obeys Raoult's law. The minimum' in the solidus-liquidus curves for the iron-chromium system shows that there are deviations from ideality in either the solid or liquid or both. Because of the importance of developing reliable techniques for obtaining activity data in alloy systems at high temperatures and of the data so obtained, an investigation of the activity of iron and chromium in the binary at 1200-1250 C was undertaken using the Knudsen cell. Experimental The apparatus and experimental procedures used in this investigation were described in a previous paper." The various materials used for the construction of the Knudsen cell are listed in Table I. The metal used for the determination of the vapor pressure of chromium was 99.9 pet pure, obtained from A. D. Mackay, Inc. The iron was obtained as electrolytic grade from Fisher Scientific Company. The Fe-Cr alloys used are shown in Table 11. The largest error and controlling factor in the accuracy in the experiments reported here are introduced because of temperature uncertainty, which is estimated to be ±3 deg C. This introduces an uncertainty of 26 pet in the measured pressure. Experimental Results and Calculations The vapor pressures of pure iron and pure chromium were calculated from the measurements by the Knudsen equation3 on the assumption that only Cr or Fe atoms were present in the gas phase. For metal vapors, at the high temperatures and low pressures involved in these measurements this should be a reasonable assumption. Whitman" corrections for the cells were made. The data and results of pressure calculations are presented in Table I, and are plotted in Fig. 1. In addition the heat of vaporization at the absolute zero, ?E°°, has been calculated for chromium. These calculations are summarized in Table 111. The data used in these calculations are as follows kelley13 (F° - E°°/T ) Speiser, et al H (F° - E°°/T ) 010 where F" — standard free energy at temperature T It was necessary to calculate the total pressure above the alloys from the total weight loss W of the cell during a run, because of the fact that all attempts to collect and analyze the chromium and iron vapor effusing from the cell in the apparatus available failed. The failure resulted from the re-

Jan 1, 1959

By Betty J. Laswell, Gerald W. Laswell

Rotary drilling in modern open-pit mining is usually considered the lead phase which not only establishes the production rates but frequently limits them. From this viewpoint alone, the drilling phase must be maximized. The drill phase is the step that permits all the other operational phases to function within their design limits. This means that, in most cases, the drill is literally run to destruction to ensure that the shovel will be able to smoothly and consistently load a manageably size muck, the haul trucks can carry a balanced load without having a boulder dropped through the bed, and the crusher can devour constant rock size.

Jan 8, 1978

By E. T. Dumble

Introduction..........914 I. Topography,........915 The Nueces Basin........915 The Coastal Slope...........918 Streams..........919 II. Geology..........921 Eocene..........923 Basal Beds .......923 Lignitic Stage........923 Atascosa Sections......924 International and Great Northern Sections .. . 928 Leona Sections.......929 Nueces Sections....929 Rio Grande Sections.....930 Lower Claiborne Stage......932 Marine Beds ........933 Atascosa Sections....... 933 International and Great Northern Sections .. . 934 Frio County Sections,.....935 Rio Grande Sections.....936 Yegua Clays........938 Atascosa Sections......938 Tilden Sections.......941 International and Great Northern Sections .. . 942 Rio Grande Sections.....942 Fayette Sands........945 Atascosa Sections......946 Tilden Sections......948 Rio Grande Sections.....950 Frio Clays........953 Atascosa-Frio Sections.....953 Tilden-San Diego Sections....955 Rio Grande Sections......955 Neocene ....966 Oakville Beds.......957 Lapara Beds,....... 987 Nueces Sections......958 Bartlett's Ford Sections.....959 Fort Merrill Section......963 Lapara Sections,.....964 Tilden-San Diego Section.....967 Lee Tiendas.......969

Jan 1, 1903