Search Documents

By Richard Hodgson

FMC Corporation, at their mine and soda ash refinery near Green River, Wyoming, currently mines in excess of 3 million tons per year of trona. Upon completion of the current expansion, the mine will be producing in excess of 4.0 million tons per year. The single level mine, approximately 1,500 feet in depth, is currently serviced by five (5) concrete lined circular shafts varying in diameter from 12 ft. to 24 ft. A sixth shaft is complete, but not yet operational and the seventh is currently being sunk. Two of the shafts are equipped with single drum hoists. The original production shaft is equipped with a double drum hoist. The newest production shaft and the main service shaft are both equipped with ground mounted friction hoists. These friction hoists have given excellent service and another will soon be installed as a man and material hoist at No. 7 Shaft. There are a number of advantages that the ground mounted hoist has over a tower mounted hoist. There are also operating problems common to both. FMC's original experience with ground mounted friction hoists began in 1962 with the conversion of a single drum hoist to a friction hoist. The converted hoist was an Ottumwa with a 5 ft. diameter drum and a 4 ft. face. This hoist had been installed at the No. 3 Shaft for some years prior to its conversion to a friction hoist. At the time the conversion of this hoist was made, there were no friction hoists in service in Wyoming. Wyoming mining laws required that all conveyances carrying men be equipped with safety dogs. Since it was desired that wire rope guides be used, safety dogs were impractical. Agreement was reached with the State Mine Inspectors that safety dogs would not be necessary provided that recommended rope safety factors for hoisting men would still be maintained if one hoisting rope was broken. Since-the shaft is approximately 1,500 ft. deep, the recommended safety factor is 6.0 so that this installation has a safety factor in excess of 8.0 for hoisting men when new ropes have been installed. The hoist conversion was engineered by Lake Shore, Incorporated. The friction ring was made in halves and bolted over the original drum face which had been machined to remove the grooves. The ring provided for four 3/4 in. diameter ropes on 8 inch center to center spacing. The pitch diameter of the modified drum was 72 inches. The grove liners are hald in place by hard-wood wedges bolted to the drum. The other modification required by the conversion was an increase in size of bearing caps and the hold-down bolts because of the increased force tending to lift the drum.

Jan 1, 1975

By Joseph E. Worthington

Many thousands of years ago when our earliest ancestor first swung out of a tree, picked up a rock, and threw it at what he hoped might be his lunch, the minerals industry, in a manner of speaking, was born. It was then a very long step indeed to the primitive metal industry of our early civilizations, for we know that precious metals were accumulated and some metal objects were produced several thousand years ago. Prospecting, or "exploration" to use the modern euphemism, consisted of little more than outcrop examination and the use of a gold pan, and it probably did not change much from our earliest civilizations until relatively recent times. In a general sense, all the early explorers of North America were also prospectors, for mineral wealth was certainly one of the goals of the first pioneers and settlers. The earliest pioneers didn't do too badly either, for they discovered copper and iron in various places in the Appalachians and Michigan, gold in the Southeast Piedmont and many mineralized areas in the Southwest. In most places these were outcropping ores or gossans, and the prospecting was incidental to the arduous task of ekeing out a living in a new land. It was the explosive discovery of rich placer gold deposits at Sutter's Mill in California that caught the public fancy and precipitated the establishment of prospecting as a full-time occupation. After the end of the Civil War in 1865, full-time prospecting became an important occupation and continued as such for almost three generations. Prospectors equipped with picks, shovels, gold pans and four-footed transportation swarmed all over what are now our Western States, discovering thousands upon thousands of mineral showings-and certainly most of today's large mining districts. Our vigorous western mining industry is a tribute to the courage and persistence of these men. The techniques of these picturesque prospectors, however, were essentially the same as those of their predecessors-examination of every outcrop and assiduous use of the gold pan. The great increase in discovery at this time was therefore due to increased activity rather than to different techniques. An important result of this in- creased prospecting was the growth of interest in geology. It was during this period that the U.S. Geological Survey began to grow. Many of the major mining districts were mapped, and geological studies and projections began to have an impact on further ore discovery. Ore search and development gradually became more geologically oriented and the geologist became a fixture in most mining camps by the 20th century. The development of mass-mining techniques in the early part of the century also changed exploration concepts.

Jan 1, 1971

By N. L. Britton

About two years ago Dr. Newberry referred to me for study a considerable collection of fossil plants sent him by Dr. Arthur F. Wendt, engineer of the silver mines " El Cerro Rico de Potosi" in Bolivia. As I had been interested in working up the extensive accumulations of existing plants made by Dr. H. H. Rusby in the Bolivian Andes further north, and in assisting Dr. Rusby in the study of those now being collected by Mr. Miguel Bang in other parts of that country, I was glad of an opportunity of ascertaining something of the Tertiary flora of the region. I was unable to take up the subject at that time, but have since been able to conclude the investigation, and the results are here presented. At a time when the mineral resources of the Southern States are attracting such widespread interest and attention, I have thought it appropriate to give a short general description of the iron-ore deposits of a territory concerning which little is as yet known and nothing published, so far as I am aware. The data used here are due to the preliminary examinations of the North Carolina Geological Survey, on which work I was engaged during the past summer, and my acknowledgments are due to Prof. J. A. Holmes, State Geologist, and Messrs. Harris, Ashe, and Lewis, of the survey, for their co-operation in the work; also to Messrs. A. S. McCreath and C. B. White for analyses which they Kindly furnished. Other analyses were made by Mr. Charles Baskerville, assistant chemist to the survey, and this may be understood where the name of the chemist is not mentioned. All samples for analysis were dried at 212' F. The accompanying map has been prepared from the revised sheets of the United States Geological Survey by Mr. H. L. Harris, and will be referred to throughout this paper. Ashe county lies in the extreme northwestern part of North Carolina, bordering on Tennessee and Virginia; it is drained principally by the north and south forks of New river and their tributaries, and is therefore on the eastern edge of the great Mississippi drainagebasin. The country is exceedingly rugged and mountainous, having an average elevation of about 2900 feet above sea-level. Jefferson, the county seat, near the center of the county, is 45 miles nearly due south from the Norfolk and Western R.R. at Marion, Va., and 30 miles northwest from the Richmond and Danville R.R. at Wilkesboro, N. C. Geologically the ore-deposits described in this paper are situated in the area of the crystalline rocks, consisting chiefly of gneiss, hornblende-schist, and micaceous schists.

Jan 1, 1893

By Frank Foote, E. R. Jette

In recent years the constitution of the high-silver aluminum-silver alloys has been extensively investigated. Hansenl has reviewed the literature to 1935. More recently, Obinata and Hagiya,2 Hofmann and Volk,3 Taziri4 and Tishchenko5 have confirmed the general features of the phase diagram in the region around 25 atomic per cent aluminum. In this paper we present the results of high-precision measurements of lattice constants of the silver-rich alpha solid solution in the homogeneous range and the neighboring two-phase regions. These results are used to establish the nature of the solid solution, the identity of directly measured densities with those calculated from lattice constants and the homogeneity limits of the alpha solid solution with respect to three different neighboring phases. A study of the earlier investigations indicated that the last two subjects in particular required new and accurate data. Experimental Procedure Preparation of the Alloys.—The alloys were made from high-purity silver and aluminum. The silver was "Proof Silver," 99.999 per cent pure, supplied by the U. S. Metals Refining Co. The aluminum was 99.97 per cent pure (contained Si, 0.009 per cent; Fe, 0.0016 per cent; Cu, 0.004 per cent) and was supplied by the Aluminum Company of America. The lattice constants of these two materials have been reported by Jette and Foote.6 Weighed amounts of the two metals were placed in alundum crucibles and melted in vacuo in a high-frequency induction furnace. The melts were allowed to cool in the crucible, the ingots thus obtained weighed about 10 grams. These ingots were then filed clean, hamered, again cleaned and given a homogenizing anneal in vacuo of from 6 to 15 days at temperatures ranging from 500" to 695°C. The ingots were air-cooled from the annealing temperature. Lattice-constant Measurements.—Carefully prepared filings for X-ray analysis were sealed into evacuated quartz or Pyrex tubes and annealed for various periods of time at suitable temperatures. The furnaces used were vertical, rapid-quenching furnaces, the samples being quenched by crushing the sample tube under water by means of a heavy plunger. The general X-ray technique has been previously described6 The cameras were of the symmetrical, back-reflection, focussing type. Ka, radiation from a cobait-nickel alloy target was used. The wave-length values were taken from the second edition of Siegbaum's book.7 A correction for the index of refraction was applied and the lattice constants were calculated by the method of Cohen.8, 6 The lattice constants were calculated to a common temperature of 25°C., using the value of the linear expansion coefficient of pure silver as 18.9 X 10-6. Presumably the expansion coefficient for

Jan 1, 1941

By A. A. Smith, J. S. Smart

NUMEROUS investigations of the effects of the various impurities common to commercial coppers have been published, and the data have found wide use in industry. Naturally, emphasis has been placed on the oxygen-bearing coppers of the tough-pitch variety, but need is now evident for data covering the oxygen-free condition as well. Furthermore, relatively few of the important reactions between oxygen and the various impurities are well understood, and often the data at hand are not applicable to the low concentrations encountered in commercial coppers. This paper presents the changes in conductivity and softening temperature derived from individual additions of the group VIII triad, iron, cobalt and nickel, to high-purity copper, and constitutes a portion of the copper-research program being conducted at the Central Research Laboratory of the American Smelting and Refining Co. The method of preparation of high-purity copper and its alloys in either the oxygen-free or oxygen-bearing form has been described previously.1 The purity of this material, and the methods developed to produce it, provide the means for direct investigation of the very low concentration range in which the various impurities generally exist in commercial coppers. The usual necessity for extrapolation to this range using the results obtained from higher concentrations, and the interfering effects of extraneous impurities, are thus simultaneously circumvented. Since previously published data have adequately presented the effects of higher concentrations of iron, cobalt and nickel, the present investigation has been confined to the composition range 0 to 0.05 per cent. All alloys were initially prepared in the form of oxygen-free continuous cast rod, the weighed alloying additions in suitable form being charged with the pure copper to the continuous casting crucible. The best of the available high-purity alloying materials were used, and spectrographic analyses confirmed the absence of interfering elements from the alloys formed. Each series was compounded in the direction of increasing concentration, starting with pure copper in a new crucible and finishing with the 0.05 per cent alloy. Composition was closely controlled by adding the alloying element in the form of a carefully compounded and analyzed master alloy rendered uniform by continuous casting. The accuracy of this method of synthesis was proved by chemical analysis of the more concentrated alloys, and, accordingly, there is every reason to credit the stated composition of the very dilute alloys in the range where chemical analysis becomes highly uncertain. Oxygen-free samples for measurements of conductivity and softening temperature were obtained by drawing the continuous cast rod to wire of 0.081-in. diameter, employing a number of intermediate anneals to refine the grain structure. The

Jan 1, 1942

By A. A. Jr. Smith, J. S. Smart

Numerous investigations of the effects of the various impurities common to commercial coppers have been published, and the data have found wide use in industry. Naturally, emphasis has been placed on the oxygen-bearing coppers of the tough-pitch variety, but need is now evident for data covering the oxygen-free condition as well. Furthermore, relatively few of the important reactions between oxygen and the various impurities are well understood, and often the data at hand are not applicable to the low concentrations encountered in commercial coppers. This paper presents the changes in conductivity and softening temperature derived from individual additions of the group VIII triad, iron, cobalt and nickel, to high-purity copper, and constitutes a portion of the copper-research program being conducted at the Central Research Laboratory of the American Smelting and Refining Co. The method of preparation of high-purity copper and its alloys in either the oxygen-free or oxygen-bearing form has been described previous1y.l The purity of this material, and the methods developed to produce it, provide the means for direct investigation of the very low concentration range in which the various impurities generally exist in commercial coppers. The usual necessity for extrapolation to this range using the results obtained from higher concentrations, and the interfering effects of extraneous impurities, are thus simultaneously circumvented. Since previously published data have adequately presented the effects of higher concentrations of iron, cobalt and nickel, the present investigation has been confined to the composition range o to 0.05 per cent. All alloys were initially prepared in the form of oxygen-free continuous cast rod, the weighed alloying additions in suitable form being charged with the pure copper to the continuous casting crucible. The best of the available high-purity alloying materials were used, and spectrographic analyses confirmed the absence of interfering elements from the alloys formed. Each series was compounded in the direction of increasing concentration, starting with pure copper in a new crucible and finishing with the 0.05 per cent alloy. Composition was closely controlled by adding the alloying element in the form of a carefully compounded and analyzed master alloy rendered uniform by continuous casting. The accuracy of this method of synihesis was proved by chemical analysis of the more concentrated alloys, and, accordingly, there is every reason to credit the stated composition of the very dilute alloys in the range where chemical analysis becomes highly uncertain. Oxygen-free samples for measurements of conductivity and softening temperature Were obtained by drawing the continuous cast rod to wire of 0.08I-in. diameter. employing a number of intermediate anneals to refine the grain structure. The

Jan 1, 1942

By Herman Garlichs

The development of the extensive Southeast Missouri deposits greatly preceded that of the Iowa and Wisconsin deposits. It began about 1720 at Mine La Motte and other localities, and has continued uninterruptedly to the present time. It is estimated that this district produced about 184,000 tons of lead in the year 1916, having a value of approximately $25,000,000. This is a new high record. The Southwest Missouri orebodies were hardly known before 1845 and were not extensively developed until 1870. Lead production in Southwest Missouri for 1916 was 38,788 tons. Oklahoma produced 14,399 tons and Kansas 2,345 tons, making a total for Southwest Missouri, and the adjoining districts in Oklahoma and Kansas, of 55,532 tons of lead. The first metallurgists in Missouri were the Indian and the hunter. The early settler learned to procure his bullets either by melting ore in his camp fire or by throwing pieces of galena on an old stump and depending on the usual roasting and reaction method to obtain the metal. A little more refined method was to arrange two flat stones in the form of a, V. Wood and galena were placed in the furnace and ignited.. As heat developed, some of the metal was extracted and molded into bullets. The next step in utilizing the lead ores was the log hearth. All lead in Missouri was smelted in this crude affair before 1820. It was built on sloping ground, and consisted of a hearth of stone, surrounded on the front and two sides by a stone wall. The wall was 7 it. high in front. The top and rear end were left open and in front an arch or opening was made, forming the eye of the furnace. In front of this a pit was dug in the ground, to receive the molten metal. Large logs were rolled in at the back and made to rest upon ledges formed inside, to raise them from the hearth and to give a draft. These logs filled the entire width of the furnace. Small split logs were then set up around the two sides and the front, and the ore was piled on until the furnace was full. Finally, the mass was covered with logs and fuel until the ore was completely surrounded. A gentle heat was started, which was raised very gradually. After 12 hr. the heat was increased and continued for 12 hr. more, 24 hr. being required for each smelting. The furnace treated about 5,000 lb. per 24 hr. and the ore yielded about 50 per cent. of its metallic lead. A considerable quantity of the ore was not desulphurized, and fell between

Jan 1, 1918

By Herman Garlichs

THE development of the extensive Southeast Missouri deposits greatly preceded that of the Iowa and Wisconsin deposits. It began about 1720 at Mine La Motte and other localities, and has continued uninterruptedly to the present time. It is estimated that this district produced about 184,000 tons of lead in the year 1916, having a value of approximately, $25,000,000. This is a new high record. The Southwest Missouri orebodies were hardly known before 1845 and were not extensively developed until 1870: Lead production in South-west Missouri for 1916 was 38,788 tons. Oklahoma produced 14,399 ,tons and Kansas 2,345 tons, making a total for Southwest Missouri, and the adjoining districts in Oklahoma and Kansas, of 55,532 tons of lead. The first metallurgists in Missouri were the Indian and the hunter. The early settler learned to procure his bullets either by melting ore in his camp fire or by throwing pieces of galena on an old stump and depending on the usual roasting and reaction method to obtain the metal. A little more refined method was to arrange two flat stones in the form of a V. Wood and galena were placed in the furnace and ignited. As heat developed, some of the metal was extracted and molded into bullets. The next step in utilizing the lead ores was the log hearth. All lead in Missouri was smelted in this crude affair before 1820. It was built on sloping ground, and consisted of a hearth of stone, surrounded on the front and two sides by a stone wall. The wall was 7 ft. high in front. The top and rear end were left open and in front an arch or opening was made, forming the eye of the furnace. In front of this a pit was dug in the ground, to receive the molten metal. Large logs were rolled in at the back and made to rest upon ledges formed inside, to raise them from the hearth and to give a draft. These logs filled the entire width of the furnace. Small split logs were then set up around the two sides and the front, and the ore was piled on until the furnace was full. Finally, the mass was covered with logs and fuel until the ore was completely surrounded. A gentle heat was started, which was raised very gradually. After 12 hr. the heat was increased and continued for 12 hr. more, 24 hr. being required, for each smelting. The furnace treated about 5,000 lb. per 24 hr. and the ore yielded about 50 per cent. of its metallic lead. A considerable quantity of the ore was not desulphurized, and fell between

Jan 7, 1917

By D. C. McLean, S. A. McKay

The purpose of this paper is threefold: 1) to describe actual ground control installations made at the various mines of the International Nickel Co. (Canada) Ltd mines in Sudbury, Ont. during a planned test program. 2) to suggest new ground control techniques which are now possible by the use of fully grouted bolts 3) to indicate the possible economic advantages to be gained by the use of resins and resin grouted bolts to control difficult ground conditions. Were a theme selected for this paper it would be: "Preserve the original roof in best condition possible by the use of smooth blasting techniques and fully grouted roof bolts — since the original rock is the best and cheapest material available for ground support." TYPES OF BONDED BOLTS As has been shown previously, there are several ways in which a bolt may be bonded. These are illustrated in Fig. 1 and 2. There are three general types of grouted bolts: 1) pretensioned, 2) post-tensioned, and 3) untensioned. The type which will be of most benefit to the user will depend upon the particular ground support problem involved. Despite the many arguments propounded for the necessity for using a tensioned bolt, ample evidence exists from actual experience that untensioned bolts can be effective in many instances. The outstanding characteristic of a grouted bolt is that it provides the user with a variety of rock consolidation techniques heretofore unavailable with conventional rock bolts. Many of the unusual characteristics of grouted reinforcing bar have been evaluated by researchers in the concrete structure field.' Underground application has largely been pioneered in the construction field, with especially good work being reported from the Snowy Mountains Hydroelectric Authority in Australia. Techniques developed there using cement grouted bolts are now being adapted in many large government construction projects in this country with excellent results. The ap- plications described in this paper are those in which Cyanamid's Roc Loc Mining Kits were used exclusively. SLUSHER DRIFTS AND FINGER RAISES (BOX HOLE BROWS, DASHES) A common mining problem especially where block caving methods are applied is that of maintaining the roof in slusher trenches particularly at the intersections of the trench with the feed raises (box holes) through which the large fragments of broken ore tumble. Typical sections are shown in Fig. 3 and 4. In Fig. 3, the drift is normally driven 7 ft wide by 8 ft high initially. The rock involved is a hard norite (diabase) which is usually competent but has "block cleavage". This roof has a tendency to fall out in large blocks when subjected to operating stresses. Depending upon the initial condition of the roof, the drift is either lined with 2 to 3 ft of concrete immedi-

Jan 1, 1964

By C. Richard Tinsley

INTRODUCTION Project financing has been defined by various authors in this book. It is founded on reliance upon the project's own future cash flows and secondarily on the collateral value of the asset base developed. It is chiefly provided by the banking community who, after an assessment of the risks involved (See Chapter 9) analyse the company's presentation (See Chapter 10) in order to structure a financing package often at a leverage of up to 80% debt. This paper describes the various support and structuring techniques used to delimit and abate the risk components perceived from the banks' experience on project development especially for the period before cash flow is generated (pre completion). ADVANTAGES The advantages of project financing extend beyond the offloading of risks to banks. Among the advantages are the following: 1. Longer loan maturity than conventional, unsecured financing; 2. Loan disbursement and repayment tailored to specific mine; 3. Ability of a joint venture without a "track record" to raise financing; 4. Obtain financing where further direct borrowing (corporate credit) limited by existing indentures; 5. Possibility of arranging finance off-balance sheets; 6. Leverage return on equity; 7. Obtain tax savings with certain project financing structures; and 8. Obtain flexible loan repayment conditions. It can also be said that from the point of view of the company, project financing has certain disadvantages which can be summarised as follows: 1. Perceived higher cost (risk premium) compared with straight corporate credit; 2. More documentation; and 3. Need to negotiate risk-sharing aspects. The main attraction of project financing is the ability to pass certain risks on to the lenders within a flexibly funded transaction. (For a more detailed description of the specific risks see the author's paper at the beginning of Chapter 9. The same risk system is followed here.) The typical project financing has corporate support prior to completion and will usually carefully control the resultant cashflow after completion to ensure the bank does not unnecessarily assume further risks of an equity nature. WITHIN THE COMPANY'S CONTROL Operating Risk This is broken into three interrelated segments for ease of description. Technical Component: This must be specifically addressed if new technology or unproven adaptations are to be used. The banks will have scrutinized the sampling and bulk testing work, perhaps grilling the geological, mineral processing, metallurgical, and mining engineering staff or consultants directly. A number of supports are available such as: TECHNOLOGY GUARANTEE: Either the company itself or the process developer will guarantee that the technology will work for a period of, say, six months to two years after startup. If not, then financial penalties will apply although these are rarely sufficient to repay the loan. Many process developers are weak financially and may have little substance to back such a guarantee.

Jan 1, 1985

Discussion of the papers of Dorsey A. Lyon and Samuel S. Arentz, p. 789; S. E. Bretherton, p. 802; H. A. Wentworth, p. 809; and Richard D. Drvine, p. 814. GeoRge W. RiteR, Salt Lake City, Utah.—We have every reason to believe that oil flotation will soon come into general use as a final guard against slime losses in concentrating mills, not only in the case of zinc ores, but also in the case of other semi-precious ores. It also promises much as a primary process for the concentration of minerals that are not adapted to gravity methods. Moreover, modifications of the process involving selective or preferential flotation are gradually becoming understood, and will make it possible to eliminate pyrite and other minerals occurring as undesirable impurities in zinc concentrates. And what perhaps is of equal importance, further modifications promise an effective method of separating zinc blende from ores that are chiefly valuable for copper, lead, and precious metals, thereby making an asset out of zinc which has heretofore been a liability. The tendency of certain pulverized minerals to float on water, especially after having been in contact with grease, has been known to mill-men for a long time, and was formerly something to be deplored and to be striven against. All at once, this tendency has become a saving grace; and now, like tardy converts to a new faith, we are zealous advocates of something we once despised. I was once employed at a mine in the Tintic mining district of Utah— the old Eureka Hill property—where ores that were too low in value to warrant being sent to copper or lead smelters were treated in a combination mill. The ores contained gold, silver, lead, copper, zinc, manganese, arsenic, etc., in varying quantities and in varying mineral forms, mingled in a quartz and calcite gangue. The material was stamped fine and then concentrated on Frue vanners so as to make a smelting concentrate, after which the tailings were thickened and treated in amalgamating pans for the recovery of non-concentratable precious metals. In the amalgamating pans, under the influence of heat and agitation, a dark greasy froth or scum sometimes formed on the surface of the ore mixture. This froth or scum was composed mainly of mineral sulphides, and its occurrence might have meant only casual losses in the previous concentration, except that the phenomenon was accompanied by faulty amalgamation of the precious metals and by excessive losses in the mill tailings. Grease and oil, present by accident, were the cause of the trouble. Whether the intense vibration in the mill, due to the pounding of the heavy stamps, had caused small particles of grease to be shaken loose

Jan 1, 1915

By C. S. Matthews, H. C. Lefkovits

The performance of depletion-type reservoirs at the stage in which the gas is at such low pressure that gravity is essentially the sole driving force has been investigated both theoretically and by use of scaled models. A simple theory is developed which completely explains the scaled model experiments. It also agrees with some field data. When the range of production rates to be considered is less than 25, the theory predicts that the production rate decline curve for homogeneous reservoirs in which there is a free surface will be of the hyperbolic type with n = 2: The theory gives a physical significance to the parameter y. INTRODUCTION This investigation was undertaken to determine a method for prediction of performance of reservoirs where gravity is the sole driving agent. Depletion-type reservoirs fall into this category after the pressure has fallen to some low value. Some examples of this type are found at Healdton ('Oklahoma), Oklahoma City (Oklahoma), Midway-Sunset (California), and East Coalinga (California). Generally the production rate per unit thickness is quite low in such reservoirs, with the conse- quence that this stage is sometimes called the stripper stage. However, per well production rates may be of the order of 50 B/D because of the considerable sand thickness open in some of the reservoirs. In the past, predictions of behavior of such reservoirs have been based on empirical extrapolation of the rate of production to the economic limit. Difficulties arise when new wells are drilled in the field or when production is artificially curtailed, since in such cases the decline rate of individual wells or leases changes and no clear trend can be detected. It was hoped that the present study would lead to improved methods for evaluation of such reservoirs. The study was initiated by building a scaled model for a particular field and by running a number of experiments on this model. Later a simple theory was developed which explained the laboratory results completely. The theory led, as shown below, to a hyperbolic-type decline equation which had been used previously' in a completely empirical manner. THEORY The General Case The problem to be treated here is the following: We are given a homogeneous cylindrical porous reservoir with exterior radius r, wellbore radius r., and height h,, containing, from the bottom up to a height hit oil, some gas, and interstitial water (see Fig. 1 A). The portion of the reservoir between K, and h, is filled with gas at low pressure, with residual oil, and with interstitial water. If at a time t = 0, the level of the oil in the wellbore is lowered to a height h,, what is the production rate from the reservoir at a time to The configuration within the reservoir at some instant

Jan 1, 1957

By J. N. Hobstetter

It is widely believed that the nucleation of phase transformations in solid metals is accomplished by some type of local atomic fluctuations in the parent phase which arise from spoutaneous difiusion in the metal or alloy system. Under appropriate conditions, these fluctuations are believed to be stable in the sense that the free energy of the entire system is lowered if the fluctuations, or nuclei, grow. Under other conditions they are thought to be unstable in the sense that the free energy is lowered if they redissolve. The criterion for stability is usually taken as the size of the fluctuation. This view has been rationalized by Beckerl in terms of the free energy released by the volume of the nucleus and the free energy associated with the formation of a new surface surrounding the nucleus. The qualitative result of this reasoning is shown in Fig I where the changes in free energy for the surface and volume effects are plotted together with their sum against the radius of the nucleus. There is evidently always a critical size r, beyond which the release of free energy which is proportional to the volume always dominates the increase of free energy which is proportional to the surface area. Borelius2 has also attempted to rationalize the stability criterion for binary alloys, but in terms of the internal concentration of the fluctuations. He has found that, if surface energies are entirely ignored, the fluctuation must still reach a critical concentration if it is to become stable and avoid subsequent dilution. Although the Borelius theory fails to predict many observed nucleation phenomena such as the vanishing of the nucleation rate at the critical temperature, the major premise must certainly be valid. In this paper a reconciliation of the Becker and Borelius views is made by means of a search for nuclei which are at once stable with respect to both size and internal concentration. The increase in free energy per mole accompanying the formation of a nucleus which is just stable, AF., is independent of the path whereby the nucleus is brought into being. It is thus appropriate to seek critical nuclear attributes without reference to the fluctuation mechanism. The rate of nucleation, however, cannot be treated without a detailed understanding of the exact fluctuation process which produces stable nuclei. In this and succeeding papers the purpose will be to find the size, shape and internal concentration of the stable nucleus which is formed with a minimum increase in free energy in a wide variety of systems. The Nature of the Nucleus It is necessary ti have rather detailed knowledge of the nature of a nucleus if AF, is to be computed. Fortunately, enough facts are known or suspected about the nucleus to make possible a detailed analysis. X ray diffraction studies have shown

Jan 1, 1949

Discussions of the papers of DORSET A. LYON and SAMUEL S. ARENTZ, RICHARD D. DIVINE, H. A. WENTWORTH, and S. E. BRETHERTON, presented at the Salt Lake meeting August, 1914, and printed in Bulletins Nos. 91 and 92, July and August, 1914. GEORGE W. RITER, Salt Lake City, Utah.-We have every reason to believe that oil flotation Will soon come into general use as a final guard against slimes losses in concentrating mills, not only in the case of zinc ores, but also in the case of other semi-precious ores. It also promises much as a primary process for the concentration of minerals that are not adapted to gravity methods. Moreover, modifications of the process involving selective or preferential flotation are gradually becoming understood, and will make it possible to eliminate pyrite and other minerals occurring as undesirable impurities in zinc concentrates. And what perhaps is of equal importance, further modifications promise an effective method of separating zinc blende from ores that are chiefly valuable for copper, lead, anti precious metals, thereby making an asset out of zinc which has heretofore been a liability. The tendency of certain pulverized minerals to float on water, especially after having been in contact with grease, has been known to mill-men for a long time, and was formerly something to be deplored and to be striven against. All at once, this tendency has become a saving grace; and now, like tardy converts to a new faith, we are zealous advocates of something we once despised. I was once employed at a mine in the Tintic mining district of Utah¬the old Eureka Hill property-where ores that were too low in value to Warrant being sent to copper or lead smelters were treated in a combination mill. The ores contained gold, silver, lead, copper, zinc, manganese, arsenic, etc., in varying quantities and in varying mineral forms, mingled in a quartz and calcite gangue. The material was stamped fine and then concentrated on Frue vanners so as to make a smelting concentrate, after which the tailings were thickened and treated in amalgamating pans for the recovery of non-concentratable precious metals. In the amalgamating pans, under the influence of heat and agitation, a dark greasy froth or scum sometimes formed on the surface of the ore mixture. This froth or scum was composed mainly of mineral sulphides, and its occurrence might have meant only casual losses in the previous concentration, except that the phenomenon was accompanied by faulty amalgamation of the precious metals and by excessive losses in the mill tailings. Grease and oil, present by accident, were the cause of the trouble.

Jan 11, 1914

The Hadsel Mill. By R. G HALL (Trans, vol 112 4000 words) This mill is designed to effect the entire reduction of ores by combined crushing and grinding from mine run size to material sufficiently fine for the usual operation of flotation or cyaniding The work is begun and completed in the same machine. The machine is designed on the principal of the elevator wheel, and crushing and grinding are accomplished by dropping a mixture of ore and water upon specially placed "breaker plates" in such a manner that the resultant material passes back into the buckets of the wheel for further elevation One method of removal of the finished product is to permit an overflow of wet pulp on one side of the mill through coarse screens A recent improvement provides for the removal of a pulp by a launder part way up the path of the buckets In either case the pulp passes to a classifier, and the oversize back to the mill in the manner familiar in ball-mill practice Although hardly through the development stage, the machine has given a very good account of itself in simplification of plant, by elimination of coarse and fine crushers with consequent reduction of installation cost and power consumption As compared with the ball mill alone, there is a reduction of power consumption as well as a material reduction of grinding steel There is an increase in cost of maintenance other than grinding steel, but as the machine passes out of the development stage there is a show¬ing of reduction of costs on this item It seems probable that with further develop¬ment and strengthening of the weaker parts further improvement may be made Ball Milling. By A. M Gow, M GUGGENHEIM, A. B. CAMPBELL AND W. H COGHILL. (Tech Pub 517; also Trans, vol 112. 24,000 words) This paper outlines a new philosophy in ball milling by using power as an index of mill operation and ascertaining the effects of the set and induced variables By recognizing the amount of ore in the mill as an important induced variable and recognizing that the amount of ore in the mill depends principally on the size of the discharge trunnion, ball volume, rate of feed, and speed of mill, obstacles formerly met were surmounted When the amount of ore in the mill is dealt with intelligently and the applied work is proportional to the amount of feed, series testing, which would otherwise give a hotchpotch, gives concordant results The study of ball paths and trajectories was seen to be fruitless when it was shown that the old attrition theory for slow mill speed

Jan 1, 1935

By John N. Hobstetter

IT is widely believed that the nucleation of phase transformations in solid metals is accomplished by some type of local atomic fluctuations in the parent phase which arise from spontaneous diffusion in the metal or alloy system. Under appropriate conditions, these fluctuations are believed to be stable in the sense that the free energy of the entire system is lowered if the fluctuations, or nuclei, grow,' Under other conditions they are thought to be unstable in the sense that the free energy is lowered if they redissolve. The criterion for stability is usually taken as the size of the fluctuation. This view has been rationalized by Becker1 in terms of the free energy released by the volume of the nucleus and the free energy associated with the formation of a new surface surrounding the nucleus. The qualitative result of this reasoning is shown in Fig I where the changes in free energy for the surface and volume effects are plotted together with their sum against the radius of the nucleus. There is evidently always a critical size r. beyond which the release of free energy which is proportional to the volume always dominates the increase of free energy which is proportional to the surface area. Borelius2 has also attempted to rationalize the stability criterion for binary alloys, but in terms of the internal concentration of the fluctuations. He has found that, if surface energies are entirely ignored, the fluctuation must still reach a critical concentration if it is to become stable and avoid subsequent dilution. Although the Borelius theory fails to predict many observed nucleation phenomena such as the vanishing of the nucleation rate at the critical temperature, the major premise must certainly be valid. In this paper a reconciliation of the Becker and Borelius views is made by means of a search for nuclei which are at once stable with respect to both size and internal concentration, The increase in free energy per mole accompanying the formation of a nucleus which is just stable, ?fe, is independent of the path whereby the nucleus is brought into being. It is thus appropriate to seek critical nuclear attributes without reference to the fluctuation mechanism. The rate of nucleation, however, cannot be treated without a detailed understanding of the exact fluctuation process which produces stable nuclei. In this and succeeding papers the purpose will be to find the size, shape and internal concentration of the stable nucleus which is formed with a minimum increase in free energy in a wide variety of systems. THE NATURE OF THE NUCLEUS It is necessary to have rather detailed knowledge of the nature of a nucleus if ?Fe is to be computed. Fortunately, enough facts are known or suspected about the nucleus to make possible a detailed analysis. X ray diffraction studies have shown3

Jan 1, 1948

By B. N. Bose, M. F. Hawk

SINCE Davenport and Bain' introduced the isothermal transformation technique for the study of austenite decomposition in steels, a new field of investigation has opened up. Extensive research has been carried out on many different steels, but relatively little work has been done on eutectoid transformations in analogous alloy systems. The researches of Smith and Lindlief,² Mack,³ and Klier and Grymko²0 on the beta-phase transformation in copper-aluminum alloys, of Hibbard, Eichelrnan, and Saunders4 and Smith5 on the kappa-phase transformation in copper-silicon alloys, of Chaudron and Forester6 on the decomposition of "FeO," and of Wasserman7 on similarities between the iron-carbon, copper-aluminum, copper-tin, and copper-beryllium systems essentially comprise the field. The iron-nitrogen system, in view of its remarkable similarity to the iron-carbon system, is particularly attractive for the study of eutectoid decomposition. The present investigation is concerned with the study of isothermal transformation, proceeding by the familiar nucleation and growth processes, and of martensitic transformation characteristics of pure iron-nitrogen alloys. The kinetics of transformation and the morphology of the transformation products have been investigated, for these must be the factors determining the properties and behavior of the final product. The Iron-Nitrogen System he binary iron-nitrogen phase diagram has been a matter of considerable disagreement among vari01.1s investigators. However, the phase diagram according to Eisenhut and Kaupp8 and Lehrer10 is now considered essentially correct as reproduced in fig. 1. The important values, 2.35 pct nitrogen and 591°C, for the co-ordinates of the eutectoid point (obtained from this diagram and used in the re- search to be described) were confirmed in a concurrent study of Paranjpe, Cohen, Bever and Floe." The eutectoid decomposition involves the transformation of the ? face-centered cubic interstitial solid solution of nitrogen in iron to the a body-centered cubic interstitial solid solution of nitrogen in iron and the ?' nitride of iron. This nitride is essentially the compound Fe,N; it also possesses a face-centered cubic lattice but a considerably larger one than the ?; the nitrogen atoms in ?' are arranged in an ordered way in the centers of the unit cubes.8,10,11 A martensitic structure has also been reported8,12 in iron-nitrogen alloys and was studied in the research to be described here. Materials and Methods The specimens used in this investigation were prepared by nitriding "pure" iron. This iron was supplied by the Westinghouse Research Laboratories and is the product bearing their trade name "Puron"; it contains about 0.04 wt pct total impurities, the major portion of which is oxygen. Specimens were ribbons several inches long, a tenth of an inch wide, and 0.125 mm thick; this was the

Jan 1, 1951

By C. R. Holmgren

A large consolidated sand core was used in this investigation. Four groups of experiments including gas drives, water drives, and water drives combined with gas injection, were made. The results of the gas-drive experiments indicate that greater ultimate recovery may be obtained by higher pressure gradients. However, other considerations challenge the absolute veracity of this conclusion. Results indicate that with connate water present and a low pressure gradient during a gas drive, less gas is required to produce a given amount of oil. The saturation gradient determined during a gas drive is presented. Results of the water-drive experiments indicate that the recovery of oil is not a function of either gradient Or input rate. The presence of initial gas saturation resulted in a slightly lower final oil saturation. Injection of sufficient gas to maintain the initial gas saturation during a water drive resulted in lower final oil saturation. Introduction With the demand for petroleum products reaching an all-time record high and the location and exploitation of new reserves becoming more difficult and expensive, the oil industry must look to more thorough and efficient methods of producing the petroleum already located. Much of the previous work along these lines is exploratory and suggests a more complete investigation. For example, a great amount of laboratory work has been done on flooding sands initially saturated roo pct with oil. Since sands saturated roo pct with oil rarely, if ever, exist in nature, and because the water content is a vital factor in the ultimate recovery from the sand, laboratory investigations on cores without water must be supplemented by comparable work on cores with water present.1'2 Other investigators have done a considerable amount of laboratory work using gas and water drives.3 Krutter and Day4 have reported results of investigations using cores saturated IOO pct with oil and have concluded that " the ultimate recovery obtained, using air drive, from a completely oil-saturated core depends on the pressure gradients used. The higher the pressure gradient, the greater will be the recovery until a certain Pressure range is reached above which the reward of increased recovery is much smaller for similar increments in pressure." Yuster and Day6 conclude that less gas and less time are required to produce a given quantity of oil at high pressure gradients than at low pressure gradients; they also conclude that an increase in the viscosity of the oil requires a proportionate increase in the gas needed for recovery. Their results indicate that the gas required to produce a given quantity of oil is greatly reduced by the presence of connate water. R. C. Earlougher2 concluded, based on results of water-flooding a large number of

Jan 1, 1949

By C. G. Dunn

MANY investigations have been made concerning the nature of plastic deformation and recrystallization of metals either in the form of polycrystalline materials or in the form of single crystals. However, similar work on strip materials composed of large grains as thick as the strip and having a high degree of preferred crystal orientation has not been carried out extensively. Such materials are ideal not only for studying changes in single crystals under conditions where neighboring grains exert their influences but also for obtaining the, complete change in orientation of a grain or group of grains during the course of plastic deformation and subsequent recrystallization. It is well known that first-order twins in the form of Neumann bands may be produced during the plastic deformation of ferrite crystals, particularly silicon ferrite crystals.1-3 Furthermore, it is believe that high-stress regions exist in the vicinity of these bands4a and it has been said that these banded regions would be active in recrystallization processes.5 Evidence to that effect in silicon ferrite had already been presented with photomicrographs showing recrystallization among Neumann bands during the early stages of recrystallization.5,6 Similar evidence has been published for nonferrous metals.5 Merging of fine parallel deformation bands during annealing to form twin bands of ordinary appearance in alpha brass has been offered not only as evidence of an active role being played by mechanical twins but also as evidence that such twins existed prior to recrystallization.5 Proof that such new structures are actually first-order twins, or even twins at all, must be considered inadequate except for those cases where X-ray or optical data have been obtained to confirm the necessary orientation relationship.7,8 A. B. Greninger has obtained excellent iliustrations of annealing twins in alpha irons Since his material was previously deformed by sharp hammering, a process that generally induces Neumann bands, the existence of twins following annealing might suggest that they grew from mechanical twins. In connection with transformation twins in alpha iron, Greninger reported that grains containing. three twin orientations occurred rarely and none occurred with three sets of well-developed bands.9 The work at the Pittsfield Works Laboratory on silicon ferrite in the form of large-grained strip steel deformed a small amount and annealed to partially recrystallize the grains indicates that the deformation and recrystallization processes that lead to annealing twins involve more complex processes than the formation of Neumann bands and the growth of such bands. Some groups of annealing twins are obtained which contain not only three well-developed twin structures, but also contain more than one order of twins. It is also shown, in one case, that an interrelated group of twins did not arise within one single parent grain and, furthermore, orientations of grains in the group

Jan 1, 1944

By J. H. Slater

There is nothing particularly new about the use of sinter in a blast-furnace burden. For many years flue dust has been sintered at the various blast-furnace plants to put it in a form that could be recharged to the furnace with some assurance that it would stay in the second time. This paper is not a compilation of scientific data but only an attempt to give our experience with sinter. There are some unexplained discrepancies in the tests given here, such as the flue dust produced and iron tonnages, but the results given are the results that were obtained. Sinter is not the cure-all for blast-furnace problems. A good coke is still the most important factor in good furnace operation. However, good sinter is a big help. As flue dust is produced under varying operating conditions and fluctuates greatly in carbon content, it is difficult to produce from flue dust alone a uniform sinter, which will give satisfactory blast-furnace results. Sinter made from flue dust alone will change in character with every carbon variation. Almost invariably flue dust contains carbon in excess of the amount necessary to make good sinter, and this excess must be burned out. This, of course, necessitates reduction of the speed of the sintering machine and thus a decrease in tonnage. An alternative is to dilute with a carbon-free material to use up the excess carbon. High-carbon material when sintered results in a very dense, undesirable product, since the excess heat melts the charge into a hard, nonporous mass, and tends to form refractory silicates. At the Republic Steel plant in Cleveland, there had existed since 1924 a continuous-type sintering machine having 224 sq. in. of grate-bar area, capable of producing 9 to 11 tons of sinter per hour from flue dust. Under a former management, it was the practice to sinter only the flue dust from the blast furnaces, no attempt being made to recover the gas-washer sludge. As the dust was limited, the plant operated only part time. In other words, there was a sintering plant representing considerable investment, with good facilities for screening and preparation of raw materials, and flue dust available for only part-time operation. The sinter produced was costly and not a very desirable product. The first step was to install equipment for the recovery of the gas-washer sludge. This was done in the form of two large thickeners and a filter, which have proved very satisfactory. It was then decided to screen out the minus 3/8-in. fines from the Mesabi ores, mix them with flue dust and coke breeze when necessary, and operate the plant at full capacity. The tonnage increased to 18 tons per hour and the product was much improved. Sintering costs fell and the product was a preferred blast-furnace material, which on an iron unit cost compared very favorably with good Mesabi ores. On the average, 40 per cent flue dust and 60 per cent fine ore was being used. The oversize from the ore screening also became a preferred product for the

Jan 1, 1941