Search Documents

By Kelly Cristina Ferreira

Na operação do alto-forno é comum observar flutuações em seu comportamento, seguindo o ciclo de vazamento de gusa e escória. O acumulo de liquido no cadinho e sua influência no aumento da força hidrostática são as principais causas dessa flutuação.O cadinho é uma parte crucial na operação do alto-forno por muitas razões. No entanto, por ser o local de acumulo de gusa e escória, este deve ter volume suficiente e facilitar uma drenagem sem distúrbios. Por isto, o estado do redutor/combustível, chamado “homem morto” desempenha uma importante função. Este trabalho apresenta uma breve revisão sobre os principais indicadores do estado interno do homem morto no cadinho do alto-forno.

Aug 16, 2017

By Daniel Augusto Godinho de Carvalho

At thyssenkruppCSA, a positive heat balance at BOF process is faced, mainly because of low utilization of scrap and plant design. A singular logistic concept for hot metal transport between blast furnace and steel plant was established to optimize transportation and energy balance. Up to 80 kg of iron ore pellets/t steel is necessary for 340t BOF heat balance. In order to accomplish this challenge a stable blowing process, intensive operational development have been successfully executed: slopping rate reduction of 80% achieved without changing the blowing time. This paper describes steps and results of this development.

Oct 30, 2017

By Jan Lückhoff

The introduction of the EAF Quantum furnace by Primetals Technologies represents an important milestone in the field of electric steelmaking during the last 15 years. In this process the latent and chemical heat of the off-gas generated during a melting process in an EAF is used to pre-heat scrap in an integrated shaft prior the melting of the scrap in the vessel. Combining proven own technologies, Primetals EAF Quantum enables nearly continuous process, cutting down idle times and enhancing availability for production. The essential benefits will be shown in this Paper.

Aug 16, 2017

By Franz Reufer

At Rogesa in Dillingen, Germany, a joint venture company of AG der Dillinger Hüttenwerke and Saarstahl AG and at Salzgitter Flachstahl GmbH in Salzgitter the sinterplants are equipped with the Paul Wurth EFA™ process for the final sinterplant off-gas cleaning. In Dillingen two and in Salzgitter one EFA™ plant are in operation at the respective sinterplants to comply with the very stringent environmental rules prevailing in Germany according to the German Clean Air Act called “TA Luft”. The main target is to eliminate or reduce emissions like dust, sulfur components, dioxins/furans and others in the sinter process off-gas. Since 2006 and 2011 the two EFA™ plant are in operation at Rogesa while the EFA™ plant in Salzgitter was also commissioned in 2011. These installations significantly contribute to the improvement of the emission situation of the Dillingen and Salzgitter Works. The EFA™ technology is the state-of-the-art process for such kind of application in terms of additive and energy consumption, reliability and availability. The report gives an overview of the EFA™ process and the performance results of the Dillingen and Salzgitter plant.

Aug 1, 2018

By "Andreas Steinwandter

The demand for increasing energy efficiency and CO2 reduction is one of the global megatrends of our time. Although the steel industry suffers from a volatile economic environment, the steel plants are interested to find opportunities for sustainable cost reduction and put efforts into healthy solutions for the environmental. Integrated steel plants are trying to cut electrical power and energy costs as these are among the biggest cost factors that can be influenced and taking all the advantages they can. For the integrated iron and steel making route the interaction of waste energy utilization along with process energy demand, natural and metallurgical gases, steam and heating systems as well as power generation has to be considered. Potential energy sources, such as sinter plant, basic oxygen furnace (BOF) cooling stack or reheating furnaces are considered in order to elaborate an integrated energy concept. Especially electric power generation is an attractive option for steel plant operators since it can easily be connected to the existing power grid of the steel plant. When direct local use of waste heat is limited, the best option is to convert it to mechanical/electrical power with a Rankine Cycle. A stand-alone system, compact design with minimum operational costs in order to fit into the existing steel plant layout, are the main requirements of such units. The objective of this paper is to demonstrate economic feasible opportunities for energy recovery for sinter cooler and basic oxygen furnace with focus on electric power generation via ORC modules taking at the same time advantages of CO2 reduction by utilizing waste heat from the process. Furthermore typical arrangements and layouts of such solutions as well as basic economic calculations will be presented in the paper.

Oct 30, 2017

By Norbert Asamer, Stefan Purrer

Depending on the product or the material grade, conventional deburring machines, such as e.g. with rotating hammers, are in many cases not capable to reliably or completely remove burrs from the edges of a continuously cast product. Burr, however, is generated at the front and/or tail ends of a slab, bloom or billet as a result from torch cutting. Likewise, traversal grinding of the slab’s rolling surfaces can also cause burr at the long side edges of the slab whereby such burr can even be more difficult to remove. Based on their experience and know-how with abrasive machining processes (abrasive cutting, high-pressure grinding) over a period of more than 50 years up to now, BRAUN has developed a highly flexible deburring grinding machine for applications which are too difficult for conventional deburring techniques. BRAUN’s deburring grinding machines were successfully introduced to the steel industry and have proven their worth under normal production conditions already. The subject paper describes the key features and advantages of BRAUN’s machine design and the operational results from the first already completed projects.

Oct 1, 2019

By Paul Riches

Today’s steel producers face the dual challenge of ensuring on-time delivery and ever demanding product requirements, while also running a lean operation. Every day the management of a long rolling plant requires continuous optimization of both operating and business practices. Imagine a long rolling facility, where individual pieces of equipment communicate with each other, where sensor information can be used not only for control purposes but to also monitor the condition of the equipment, where models are used to verify the process is within working limits and the equipment raises alerts to operators when it requires maintenance! Utilizing the ongoing evolution in technology though data collection, communication, internet of things, control techniques and smart sensors, there is now more information available than ever before. The collection and analysis of this information will both advance control and monitoring of plant performance; revolutionizing long rolling mill plants worldwide and optimizing the entire value chain, along with improved and more flexible production.

Oct 30, 2017

By Marcela Gotelip Barbosa

Pellets are the main iron input to the blast furnace at ArcelorMittal Lazaro Cardenas iron and steel making facility in Mexico. Pellets are made at this facility using the concentrates generated and shipped from their captive mines viz., Las Truchas, Pena Colorada, Volcan Sonora. The concentrating plants, after grinding the ore to the liberation size, use magnetic separation and flotation to reject the silica, sulphur and phosphorous impurities. At Volcan Sonora Mines, the ore is contaminated with phosphorous minerals, and hence, after magnetic separation, the phosphate minerals are floated using anionic carboxylate collector (sodium oleate). Apart from floating the phosphate minerals, the sodium oleate also has some tendency to smear on the iron bearing mineral surfaces leaving a hydrophobic surface, which is expected to reduce the green pellet strength due to absorption of ultrafine sized air bubbles on these surfaces, and further generate higher levels of dust during the induration process. In order to alleviate this industrial problem, comparative studies were carried out on the concentrates from magnetic separation using reagents from synthetic sarcosinate and carboxylate family collectors. Results have indicated that the sarcosinate family members not only were found as replacement to carboxylate collectors, but also reduce the phosphorous content below the values achieved with oleate, thus have considerable benefits in the downstream steel making process. Based on the results, plant runs are being taken up at Volcan Sonora. In this article, the laboratory results obtained on iron grades and recoveries, and phosphorous rejection using both the reagents are presented.

Aug 1, 2018

By Andrew Slifka, Pello Uranga, Douglas Glenn Stalheim

Structural steel final mechanical properties of strength and ductility are predominately generated by the final ferrite grain size/packet size and homogeneity of that ferrite grain size/packet size through the cross-sectional area. Forty to seventy percent of the strength components come from how fine the final cross-sectional ferrite grain size/packet size that can be produced.[1] All the ductility properties of structural steels for a given microstructure are predominately driven by how fine AND homogenous the final cross-sectional ferrite grain size/packet size can be refined.[2,3,4] One key ductility property of structural steels used in construction and energy transmission applications is fatigue. Both low and high cycle fatigue can be realized in these end applications, however, low cycle fatigue is typically the predominate mechanism. In construction applications the environment for fatigue is typically air, such as in wind towers or high-rise building construction. In energy applications, there is an interest in high pressure (5.5 – 21 MPa, 800-3000 psi) gaseous hydrogen as an alternative fuel source to fossil fuels. A project to study the effect of the cross-sectional grain size/homogeneity of a relatively pure polygonal ferrite microstructure on the fatigue performance in air and high-pressure gaseous hydrogen has been developed. This paper will discuss the project strategy, microstructure developed for the project and initial test results.

Oct 1, 2019

By Rudolf Hubmer

In October 2013 JSW Steel decided to place an order to Primetals Technologies Austria (former Siemens VAI Metals Technologies) for the installation of a comprehensive Level 2 process optimization system for more than 20 existing production facilities of various suppliers. For SMS-I new L2 systems are provided for two hot metal pretreatment stations, three hot metal desulphurization stations, three ladle furnaces, two 1-strand slab casters, a ladle tracking system as well as a shop supervisory system. Additionally the existing L2 system for one 1-strand slab caster is being upgraded in the course of the project. In SMS-II new L2 systems for the 7 hot metal desulphurization stations, 4 ladle furnaces, 1 new RH vacuum degasser, ladle tracking system and a shop supervisory system are supplied. Despite of the challenging time schedule the commissioning of the single facilities started within less than 12 month after contract effectiveness. The installed Level 2 process optimization systems together with the achieved results are described in this paper.

Aug 16, 2017

In today’s competitive steelmaking environment, the optimization and continuous supervision of the blast furnace process is of major importance. Modern probes and process measurement systems can assess the specific operation of the blast furnace. They provide a better and detailed process understanding and control. The benefits are even more important when they are combined with process models and expert systems. Everyday operation, productivity and even the lifetime of a blast furnace can be significantly improved by collecting, interpreting and acting upon such process data correctly. Only a comprehensive knowledge of the various process phenomena together with measurement of process variables inside the blast furnace enables the operators to optimize coke and fuel rates, to run the blast furnace smooth, reliable, and safe, and to make best use of the available raw materials. While the improvement of the blast furnace process with respect to productivity remains the main task, also, the timely identification of abnormalities and the assessment of process variations is an objective. This paper describes the blast furnace measurement systems that are available for everyday automatic use and provides an understanding for the possibilities of modern probes. The different applications are daily blast furnace supervision, charging process optimization, and observation of the internal state. Finally, the paper gives recommendations on probe configurations for different blast furnaces sizes, considering both a technical and an economical point of view.

Aug 2, 2018

By Marcus Vinicius Laudares Mendonça

SMS calculates and improves tooth and flank profiles individually to realise a homogeneous pressure distribution over the complete load flank. With a tooth profile and flank profile according to AGMA, ISO or DIN standard the contact pressure varies along the load flank. To realize a homogeneous distribution of the contact pressure and to avoid a premature mesh, SMS improves the tooth profile and flank profile in three steps. First SMS is doing a preliminary calculation and design according ISO, DIN or AGMA standard, with safety factors based on more than 125 years of experience. Second SMS calculates and checks the local contact pressure at the load flank under consideration of shaft, gearing and housing deformation, as well as the bearing behaviour. Finally SMS calculates and designs an improved tooth profile and flank profile to receive a homogeneous contact pressure at the load flank. The result is an increase of the torque transmitting capacity of up to 30% of the SMS advanced gears with the same outer dimensions than traditional gears.

Aug 17, 2017

By Antonio Esposito

Saving energy and reducing pollution by minimizing emissions are today great challenges in the coking industry worldwide. In order to achieve satisfying results, equipment as well as technology should be continuously improved and updated. The most modern design tools should be adopted to maximize the coke production rate also ensuring the best coke quality. In this scenario, Paul Wurth is realizing the new coke making plant of CSPecem, Ceara - Brazil. These batteries are based on Paul Wurth “jumbo oven concept”. This solution incorporates all most modern features and design upgrading, in the aim of an easy and long-lasting operation putting a particular attention to environmental performances: the reduced number of ovens and the low number of pushing per day have the main effect of reducing pollution sources. Finally the paper will highlight Paul Wurth SOPRECO® System, which is foreseen to be installed in CSPecem batteries. SOPRECO®, which is capable of controlling the pressure for each individual oven in a coke oven battery, is thus able to reduce volatile emissions through doors, roofs and stand pipes up to 90%. The coke oven gas (COG) produced during the carbonization process is cleaned in a coke oven gas treatment plant to the level stipulated by applying the Best Available Technology (BAT).

Aug 1, 2018

By Bruno Gomes Silva

O Distribuidor é um equipamento indispensável e de grande importância no processo de solidificação do aço via Lingotamento Contínuo. Os distribuidores são revestidos por um material refratário de trabalho que entrará em contato com o aço líquido. Atualmente é utilizado um revestimento que possui a necessidade de adição de água durante a aplicação, que poderá ser manual ou automática. Com o distribuidor disponível para lingotamento, o mesmo é direcionado para as máquinas de lingotamento onde serão pré-aquecidos visando retirar o excesso de umidade e promover a sinterização do refratário. O presente trabalho apresenta uma alternativa de revestimento, onde não é utilizada água na aplicação do produto, ou seja, um refratário com características de auto-endurecimento que permite iniciar o lingotamento sem haver necessidade de pré-aquecimento, o que significa partir a frio com o distribuidor.

Aug 16, 2017

By Alessandra Vieira Guimarães

A superliga de níquel 718 é uma superliga endurecida por precipitação, com alta resistência mecânica sob condições extremas e ambientes agressivos. Encontra aplicações como componentes críticos para indústrias aeroespacial, óleo e gas e nuclear. Seu alto teor de elementos de liga promove a ocorrência de diversas fases com consequente impacto nas propriedades. O presente trabalho foca na comparação por análise de imagens na morfologia, fração volumétrica, tamanho médio e distribuição de partículas de carbonetos (Nb,Ti)C após duas rotas de processamento termomecânico. Sua quantidade, distribuição e morfologia podem ter um papel em processos de degradação como corrosão e fragilização ao hidrogênio. Portanto, é importante saber como se desenvolve sob diferentes rotas de processamento.

Aug 16, 2017

By Juergen Meisel

The paper will explain how to successfully implement a robotic solution from the initial idea to a working industrial solution. Primetals Technologies can call upon 10 years of experience in installation of Robot solutions in the harsh environment of steelmaking plants - the so-called LiquiRob. To enhance an existing shroud manipulation system, the idea to connect the shroud with a bayonet mechanism to the ladle nozzle was born in accordance with the requirements of a well-known steel producer. The paper will describe the development steps from the first simulations and prototype testing in the laboratory, it will show the intensive system testing under workshop conditions and will finally depict the successful integration into the plant. Furthermore, operational experience will be shown as well as the advantages of such an installation compared to other shroud manipulation systems.

Oct 30, 2017

By Thiago Félix dos Santos

A maioria dos materiais poliméricos sintéticos apresentam superfícies quimicamente inertes, isentas de porosidade e baixa energia de superfície. Este trabalho tem como objetivo realizar a modificação superficial do substrato têxtil de forma a aumentar a sua molhabilidade. Os tecidos de poliéster são hidrofóbicos e, por isso são desconfortáveis aos usuários, pois a fibra não absorve o suor do corpo, outro fator que é prejudicado pela hidrofobicidade da fibra de poliéster é o tingimento das mesmas. Portanto, tratamentos superficiais vêm sendo utilizados para minimizar esse problema e o plasma é uma técnica que se mostra bastante eficaz. O plasma ao interagir com a superfície do substrato provoca alterações químicas e físicas melhorando suas propriedades. Portanto, através do plasma é possível alterar as propriedades físico-químicas das superfícies de tecidos de poliéster, tendo como resultado o aumento da hidrofilidade dos mesmos com o incremento de grupos funcionais polares e o aumento da rugosidade em sua superfície. As amostras foram tratadas em um reator de plasma de barreira dielétrica a pressão atmosférica, em diferentes tempos de tratamento e voltagem. Após as funcionalizações as amostras foram submetidas ao teste de capilaridade, a fim de observar a melhora na hidrofilidade. Todas as amostras tratadas tiveram aumento na molhabilidade, com exceção, as amostras tratadas com 10 kV, onde não houve alteração.

Aug 7, 2018

By Bryane Prando Brandão

Aços microligados expostos a ambientes contendo H2S e CO2 (sour gas) sofrem corrosão generalizada que promovem a entrada de hidrogênio atômico no metal, causando fragilização por hidrogênio, podendo gerar falhas graves no material. O objetivo deste trabalho é estudar o grau de fragilização, utilizando ensaio Charpy, de um tubo API 5L X65 após diferentes tempos de imersão em uma solução saturada com H2S. O eletrólito empregado foi solução A (ácido acético contendo cloreto de sódio) da norma NACE TM0284-2011, fazendo-se purga com N2 e injeções de H2S. Os corpos de prova padronizados foram imersos durante 96 e 360 horas, sendo que após doze dias do término da imersão, foram realizados os ensaios Charpy. Foram levantadas as curvas da energia absorvida em função da temperatura, para corpos de prova com e sem imersão. Os resultados mostraram que mesmo após imersão, não houve modificação significativa na temperatura de transição do material, apenas uma pequena diminuição da energia absorvida. Esse comportamento sugere que o teor de hidrogênio em solução sólida aumentou em função do tempo de imersão, levando a tais resultados. O refinamento da microestrutura e o baixo nível de inclusões estão relacionados a baixa quantidade e uniformidade da distribuição dos sítios de ancoramento de hidrogênio irreversível, o que pode explicar o desempenho obtido.

Aug 7, 2018

By Rodrigo Daniel Barbosa Pires, Sabrina Sadalla Collese, Mauricio Lopes Molina

A eficiência nos fluxos logísticos passou a ser um diferencial para as empresas; uma logística eficiente traz melhorias tanto no nível de atendimento, como na redução de custos e responsividade ao processo. Um dos grandes desafios para as companhias é prever a demanda interna por produto de sua produção alinhada à sazonalidade e ao planejamento de atendimento da movimentação destes materiais entre as áreas produtivas, a fim de assegurar as políticas internas da empresa, regras de segurança, além da necessidade de otimizar o processo e reduzir custos. O presente trabalho tem como objetivo comparar o modelo sem tecnologia e o modelo implementado com novas tecnologias referentes às movimentações internas de materiais da usina, fomentando as problemáticas no processo, os desafios de implementação das tecnologias, bem como os benefícios alcançados.

Oct 1, 2019

By Fernanda Simões Ribeiro Curcio

Durante muitos anos, diversas edificações na planta da ArcelorMittal Tubarão, tais como: unidades fabris, vestiários, canteiros e refeitórios, foram construídas utilizando concreto armado. Aplicar o aço na construção civil e, desta forma, fomentar o uso do aço nesta área, sempre foi uma grande vontade da empresa. Nos últimos anos, esse interesse tem se tornado realidade, tendo sido adquiridas edificações construídas com sistema Light Steel Framing e outras estruturadas em perfis laminados. Além de impulsionar o consumo do aço, essas unidades apresentaram diversas vantagens em relação à construção em concreto armado, como: redução no custo de implantação, melhor controle do cronograma de execução, abatimento no prazo para execução dos serviços e menor exposição dos trabalhadores aos riscos operacionais, já que apenas as interligações das utilidades foram executadas no local. As primeiras unidades adquiridas tem apresentado excelente desempenho ao longo do tempo, mesmo considerando o ambiente industrial e marinho ao qual a planta da ArcelorMittal Tubarão está submetida.

Oct 30, 2017