Search Documents

By V. L. Andrade, K. L. C. Goncalves, N. A. Santos

This paper describes results obtained in a test program performed with new equipment, called Mini Pilot Plant, manufactured by Canadian Process Technologies. This equipment was acquired by CVRD aiming at testing flotation circuits, in a continuous closed configuration, with samples obtained from drill cores. Success of this goal would allow CVRD to establish the metallurgical performance of mineral deposits with more confidence in comparison to Locked Cycle Tests (LCT). This paper discusses the importance of assessing the ore variability and compares results obtained in LCTs and Mini Pilot Plant. Results suggest that more reliable data is obtained in MPP test.

Jan 1, 2002

By M. Courchesne, C. Barbery, D. Hodouin, C. Carrier

"The carbon-in-pulp process for recovery of gold dissolved in dilute cyanide solutions, in the presence of solids, has now replaced the convedntional processes of pregnant liquid/barren solids separation followed by Merrill-Crowe precipitation. Most plants built over the past ten years incorporate a CIP section. The process is described as cheaper in capital and operating costs, and few major start-up or operational difficulties are reported. For the purpose of the present paper, the CIP process will be assumed to consist of the following sequence of operations (Figure 1):- the slurry stream coming out of the cyanidation circuit is first screened to remove any tramp oversize material. Gold dissolution is assumed to be complete before entering the CIP circuit.- the slurry is sent into a series of agitated tanks in which it is mixed with activated carbon. The carbon particles size is much coarser than the top size of the ground ore. The tanks are fitted with screens that allows the slurry to overflow continuously into the next tank, while retaining the carbon in the tank. Slurry dilution is adjusted to prevent carbon from settling in the tanks. Agitation intensity is kept low in order to minimize carbon abrasion.- carbon is transfered from tank to tank in a discontinuous manner. According to a specific schedule, the carbon from tank one is removed, then carbon from tank two is sent to tank one, and so on, till the last tank, which is filled with regenerated carbon corning from the elutionregeneration section. The amount of carbon removed, the transfer from tank to tank, the sequence of transfer, the carbon inventory in the various tanks are parameters which are, up to a point, at th2 discretion of the operators, as long as they remove, batch wise, an amount of loaded carbon containing a similar quantity of gold to the one that has entered the circuit since the last transfer."

Jan 1, 1987

By Rodrigo Jerez

Advances in inexpensive computer automation led to the development and use of a computerized ore control system at the Cyprus Copperstone Gold Mine near Parker, AZ. These new ore control practices improved accuracy, performance and productivity of the ore control effort. An automated system for data collection, including bar coding of blasthole samples, laboratory analysis, data management, grade estimation, cut delineation and ore zone stake out, plays a major role in ore control practices. This is of particular interest because of the large amount of blasthole information being processed, analyzed and reported daily. Copperstone Gold management has been progressive toward new, efficient methods regarding ore reserve estimation, long-term mine planning, short-term mine planning, ore control and surveying. Technological advances, including powerful personal computers, applicable mine planning software and surveying instrumentation, have become readily available and affordable. The computerized ore control procedures used at Copperstone include sample data collection, laboratory automation and computerized data management. These have reduced the time to complete ore control on a blast pattern by 50% to 75%. The final product - ore control - is generated in a more timely and accurate manner.

Jan 1, 1991

By Agne Rustan

The goal of this paper is to describe Fragblast 10 for those who did not have the opportunity to attend the Symposium and also give some examples of new research findings used in practise in some countries throughout the world. Also some entertainment events from the symposium are described.

Jan 1, 2013

By Jonathan Baggett, Nino Ripepi, Amin Abbasi, Richard Bishop, Juan Monsalve, John Hole

This work focuses on the operational and safety issues associated with karst voids in large opening underground mines. Issues include water inrush, structural instability, and engineering uncertainty in these environments. Coupled with the fracturing prevalent in folded sedimentary rocks, karst voids are complex and challenging ground-control risks. Traditional methods of predicting karst void locations, such as probe drilling, are impeded by the inconsistent spatial distribution and variable sizes of the features as reported by Li et al. (J Rock Mechan Geotech Eng:232–242, 2010) and Hassan et al. (Procedia Chem 19:737–742, 2016). Ground-penetrating radar (GPR) is a geophysical technique that transmits radio waves into a medium and subsequently detects reflected waves via a receiver. The travel time and energy of received signals are then processed and interpreted. The difference in conductivity and dielectric permittivity between limestone and open karst cavities causes strong reflections. GPR is frequently used as a geophysical surveying technique in several industries; however, there is a lack of published research on underground mining GPR applications as reported by Zhao et al. (2015a; Geophys J Int:62–71, 2015b) and Eskelinen and Pellinen (Constr Build Mater:888–898, 2018). The purpose of this work is to demonstrate the use of GPR in an underground stone mine and to discuss the importance of karst void detection ahead of mining.

By T. Z. Mugodi, D. R. Fleming

Information and Communications Technology (ICT) is defined as ‘The goods and services that support the electronic display, processing, storage and transmission of information’. Early in 2002 the South African Department of Trade and Industry (DTI) commissioned a study into the diffusion and adoption of ICT in eight sectors of the economy. The platinum mining Sector was one of these. The key findings presented in this paper are based on the platinum sector component of that study. The paper examines the theoretical basis behind technology transfer and innovation diffusion and presents the results of an ICT diffusion survey carried out in the South African platinum mining sector. ICT is shown as the modern day technological tool which is an accelerator of economic development. The current state of ICT diffusion in the platinum mining sector is defined and projections for the near future are given. Recommendations which will ensure smooth and full adoption are presented and justified.

Jan 1, 2003

By M. J. Beus, B. Stewart, S. Iverson

Synopsis U.S. Mine Safety and Health Administration (MSHA) accidents statistics have identified ore-pass hazards as a significant safety problem in U.S. underground metal mines. The statistics show that nearly 75% of injuries are directly or indirectly related to pulling or freeing of ore-pass chutes, the use of hand tools in ore passes, fails of broken rock in ore passes and structural failures of chutes or gates and ore-pass walls. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines. Risk assessment methods, such as fault-tree analysis, have been employed to identify the most probable causes of orepass failures, define research priorities and analyse the factors that result in malfunctioning and unsafe ore passes. Static and dynamic loads are being measured in a laboratory setting with the use of a reduced-scale orepass mock-up. Field tests are being initiated in mine ore passes to determine static and dynamic loads. Data from the test ore passes are being compared with data from the mine to characterize true system behaviour. Computer modelling with the use of closed-form solutions, finite-element analyses and a newly developed particle flow code predicts static and dynamic leads from the flow and the impact of ore and waste in the ore pass. Preliminary results indicate that dynamic impacts from ore and waste rock might be considerably greater than expected. The total static load is substantially less than is typically used fur the structural design of chute and gate support members. It is suggested that damping factors, normal and shear stiffness and mass frictional characteristics have a significant effect on particle flow and resulting impact loads. This is being verified with the use of results from laboratory tests, field tests and particle flow analyses. Ore passes are vertical or steeply inclined openings in a rock mass through which ore and waste are transported and where they mar also be stored. A typical underground mining system is shown in Fig. 1. The arrows indicate the locations of ore passes and loading pockets and their relative configurations. The control of material flow is potentially one of the most hazardous operations in underground mining. According to MSHA data. most of the ore pass-related accidents in the U.S.A. are associated with the loading-unloading cycle and removal of blockages from ore passes. In particular, attempts to free ore hang-ups have resulted in multiple fatalities. The hazards are obvious; there is uncertainty as to when the ore will break loose and miners are unable to escape falling rock to a safe location. Although ore passes and chutes and gate systems for underground metal and non-metal mines roust meet the requirements specified in the U.S. Code of Federal Regulations (CFR). Parts 57 and 75, recent structural failures of ore-pass linings and gates have underlined the lack of adequate ore-pass design standards available to both MSHA enforcement staff and mine engineers. Because of the importance of an ore pass to the safe operation of a mine design criteria need to be assessed and new guidelines developed. Researchers at the Spokane Research Laboratory of the Nationals Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines and studying design criteria for ore passes. The near-term goal is to conduct laboratory and field experiments and computer modelling to evaluate the ore-pass design criteria currently used. Literature searches, field site

By Andrew Brown

"In recent years operators of brown-ore mines have shown increasing interest in .the reclamation of ore heretofore lost in tailing ponds. In January and February.1945 the author made a preliminary survey of the ponds in the Russellville district, Franklin County, Ala. The Russellville district (fig. 1) was chosen for the preliminary work because it contains many large ponds in a comparatively restricted area. All important properties in the district were visited with Charles R. Wilson of Russellville, who has been familiar with the Franklin County brown-ore industry since 1890; with Edmund Craddock and W. S. Blackburn, managers of the two washers now operated near Russellville by Shook & Fletcher Supply Co., and with S. A. Britton, manager of the Sloss-Sheffield Steel & Iron Co. washer. The larger ponds were measured roughly and tonnages estimated. and samples taken from different areas were analyzed and beneficiated at the Southern Experiment Station of the Bureau of Mines; Tuscaloosa, Ala.The ponds explored were the Sloss No.1 (Ensley); the Sloss No. 8, and the Sloss No. 4-5, which are among the largest in the district and so located, within an area of .three square miles (see fig. 2), that ore from all of them could be-treated,one centrally located washer.Actual work was begun on May 9. Between that date and June 30, when field work was completed, 246 holes in ponds were drilled and sampled, and 15 additional holes were put down primarily to test the drill .in different types of ground with a view to its possible utilization in other types of prospecting. Samples from all holes were analyzed for iron content; samples from 13 holes were sized and analyses made for each size fraction, and six large samples have been composited for beneficiation tests.Brown iron ore has been mined in the Russellville district since 1815, when the first blast furnace in Alabama was built in NW1/4 sec. 10, T. 7 S., R. 12 W., about 3 miles southwest of Russellville (19).-J The furnace was abandoned before the Civil War, and mining continued on a small scale until 1888, when Enoch Ensley began to mine the ridge between Russellville and Pain Creek. His first washer, Ensley No. 1, was about 300 feet south of the junction of the present Tharptown road with the Waco spur of the Southern Railway."

Aug 1, 1946

By F. P. Hassani

Today, mine backfilling has become an integral part of mining operations, both from a local and overall ground control point of view, and as regards mining techniques and environmental considerations. During the past decade, substantial research has been carried out to contribute to the better understanding of the mechanisms involved in mine backfill behaviour. This work involved analytical, experimental and numerical studies at different scales. Accordingly, this work has been aimed at developing backfill design guidelines for actual working conditions. Backfill design for deep mining conditions is complex and requires understanding of various elements. The most important of these elements are: backfill inherent strength parameters, backfill placement method, stope geometry and interaction between backfill and host rock. The mobilization of backfill strength parameters controls the backfill behaviour and thus, its failure mode. It is believed that the governing boundary conditions and backfill-rock interaction influence the backfill strength mobilization significantly. Accordingly, the interaction between backfill and host rock is an influential factor in overall backfill behaviour under applied loads. The focus of this research is to investigate the backfill-rock interaction, considering a nonlinear behaviour for both backfill and rock mass. Assuming typical stope geometry, the FLAC code was used to model the complex boundary condition associated with narrow vein mining conditions and to simulate the backfill behaviour. A comprehensive numerical study was conducted and the results obtained were compared against field observations. The analysis of findings provides qualitative results, which can be used for backfill design. Keywords: Numerical modelling, backfill, deep mining, non-linear behaviour, rock mechanics, backfill behaviour, narrow vein mining.

Jan 1, 2008

By D. W. Euler, D. G. Brophey

"In an attempt to address the issue of rising labour costs, and to improve productivity, a laser-based system to guide underground LHDs and trucks has been developed. This comprehensive system is known as the Opti-Trak system.Essentially, the vehicle is equipped with front and rear-mounted lasers which scan a reference strip mounted on the drift back. The vehicle follows this reference strip and in addition, based on reflective bar codes mounted beside the reference strip, initiates certain functions (i.e. dump cycle, speed change, brake check, etc.). Any programming that is drift-specific is handled by the positioning of the reference strips and bar codes. Consequently, the vehicle can easily travel to many different haulageways or branches, providing the reference strip and bar codes are in place.The advantages of this system are an immediate elimination of haulage operator costs and an increase in available hauling time to 7 hours out of an 8-hour shift as compared to the typical 5Y2 out of 8 hours that a manned haulage system offers.This paper describes the Opti-Trak system and the benefits to be realized from automation of mine haulage requirements."

Jan 1, 1994

By J. F. Wilson

An experimental investigation has been made of gas-driven slug displacements in a system of high gas saturation to evaluate the process for use in a California reservoir. Fluid compositions, temperature, pressure and core permeability duplicated reservoir conditions as closely as possible. The temperature was above the critical of the slug materials. The slug composition required for 100 per cent oil recovery in the linear flow systems was found to agree with that determined from equilibrium phase studies. A qualitative theory for the slug displacement of two-phase systems is proposed and found to be in general agreement with the observed flow behavior. The theory predicts that the length of the reservoir fluid-slug transition Zone will increase with increased initial gas saturation and decrease with increased oil swelling accompanying the composition change from reservoir oil to the critical composition. The precipitation of small amounts of an asphaltic phase during the formation of the transition zone had no adverse effects on the flow behavior of otherwise miscible systems. INTRODUCTION Despite the large number of recent publications relating to oil recovery by miscible displacement, little information is available concerning the behavior of crude oil-natural gas systems at conditions likely to be encountered in field application. The laboratory data reported here were obtained during an investigation of the possibility of using a gas-driven LPG slug in a partially depleted California reservoir. Seven gas-driven slug displacements employing slugs of different compositions and sizes were made in 26- to 27-ft long sandstone cores. The equilibrium phase behavior of the systems was also determined. The features of primary interest in this study are the following. 1. Data were obtained on the displacement of reservoir fluids at reservoir conditions. 2. A high gas saturation existed in the long cores at the start of the displacements. 3. The temperature of the studies was above the critical of the slug materials. 4. A comparison between the flow behavior and equilibrium phase behavior, as illustrated by a pseudo-ternary phase diagram, is afforded for a system of considerable complexity. THEORY Phase Behavior The use of the pseudo-ternary phase diagram to illustrate the phase behavior in miscible displacements has been discussed by Clark, Schultz and Shearin. Sie-vert, Dew and Conley and Arnold, Stone and Luffel' have presented both phase equilibrium and flow data for true ternary systems. For the true ternary, the application of the theory is straight-forward; for a reservoir system represented as a ternary, the theory undoubtedly gives a qualitatively correct picture. One purpose of this investigation was to see if the pseudo-ternary phase diagram could be used to predict with reasonable accuracy the conditions necessary for miscible displacements with actual reservoir systems. MiscIBLE Displacement of Two-Phase System A large number of papers "I3 have treated the miscible displacement of a single-phase fluid from both an experimental and a theoretical viewpoint. However, the normal field application of the process will be in a partially depleted reservoir. Often the state of the system will be such that the mobility of the gas phase is greater

By Edmund S. Leaver, Charles E. Van Barneveld

In response to numerous requests from metallurgists and operators for information regarding the status of the sulphur dioxide leaching process , developed at the Southwest experiment station of the U. S. Bureau of Mines , Tucson , Ariz . , the following statement has been prepared . A more complete report is now in course of publication and will appear as Technical Paper 312. This process was devised to provide a cheap and efficient method for treating the so- called "porphyry " copper ores of the Southwest which generally contain both " sulphide " and "nonsulphide " copper minerals , mixed in such proportions that they can only be satisfactorily treated by a method which will concurrently recover both the sulphide copper and the nonsulphide copper . The latter term has been adopted to include all the minerals commonly referred to in operating phraseology in the mills of the Southwest as " oxidized" , " oxide " , or " soluble " copper . confident that the sulphide dioxide leaching process , as developed by us with the cooperation of the Miami Copper Co. and the Arizona Copper Co. , is suitable and commercially available for a wide range of ores .

May 1, 1922

By L. D. Haig

"The Texada Mill is a unique iron operation producing High Grade sinter iron concentrate and a by-product copper, gold, silver concentrate. The plant is complex and extremely flexible to handle the many varieties of ore. Two iron concentrates are made and blended. A coarse iron concentrate from primary grinding and a fine concentrate after rougher flotation to remove all the sulphides.All the tailings from iron processing are collected, dewatered, reground and floated for additional copper recovery.The entire milling operation has been carried out in all sea water for seven years and mixtures of sea, fresh, and reclaimed water for ten years prior to that.A very stable float results from the use of sea water at the natural pH8. Reagent Consumption is lower and Metallic Corrosion of mill liners and grinding media is actually less than local fresh water or mixtures of fresh and sea water.Marine growth in pipe lines can be periodically removed by violently bubbling high pressure air up through the water filled mains.Location:Texada Mines is located on tide water on the west side of Texada Island 100 miles northwest of Vancouver, B. C.The Island is served by a 30 car ferry, tug and barge and a scheduled air service from Vancouver to a company maintained air strip near the mine.The climate is moderate with about 30 inches of rain during the winter and relatively dry summers."

Jan 1, 1974

By J Taylor, L Richards, M McKenzie

When a collapse in its services shaft caused rapid gas build up and its premature closure in. 1951, the Blackwater Mine at Wiauta was in full production with significant ore reserves yet to be mined. A total of nearly 23 tonnes of gold was produced from the mine during its 44 year life. It was New ZealandÆs deepest underground mine, producing gold from an extensive sub-vertical mineralised quartz reef that averaged 0.6 m in width. Mining was by stoping between adits and short shafts, latterly with the main mine access through the 840 m deep Prohibition shaft. Macraes Mining Company Ltd are presently investigating the possibility of reopening the mine. This paper outlines a preliminary assessment of the main geotechnical factors for achieving the reopening, using recent exploration and old mine information. The greywacke host rock mass in the vicinity of the quartz reef has been evaluated using both these sources, and the paper discusses how the geological structure, intact and rock mass strengths, the rock mass defects, in situ stresses, and groundwater inflows may effect the reopening and support of the prohibition shaft, the excavation methods and support for a new supplementary shaft, and the likely excavation and support requirements for working adits and stopes in the rejuvenated mine.

Jan 1, 1996

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 30 jurisdictions of the Western Hemisphere. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; and third, analysis of laws applicable to natural gas, petroleum, and related materials. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of States or Provinces, those areas are considered separately from the central government.

Jan 1, 1970

The commercial development of the shallow (2200 ft2 400 ft) Windalia sand reservoir at Barrow Island provided the opportunity to conduct an intensive drilling programme using equipment and techniques designed for optimum performance.During the initial exploratory and reservoir delineation phase, 12 specific Windalia test wells were drilled using drilling equipment with an optimum depth range of 6QOO ft - 8000 ft and a 9 5/8 in by 7 in. casing programme was employed. The average time from commencement of move-in to rig release exclusive of coring for five representative wells was 187 hr during this phase.Development drilling commenced December 1966 with one rig, with the second in operation January 1967.As of January 1 1968, 168 development wells had been completed. The two rigs employed are drive-in units equipped with a telescoping .gelf raising doubles mast.Optimum depth range with 4 1/2 in. drill pipe is 2500-4000 ft. Casing programme is 8 5/8 in. by 5 1/2 in. Efficient performance was achieved immediately. The average time from commencement of move-in to rig release for 15 wells drilled early in the development programme was 99 hr.By application of experience and further modification of techniques, performance was improved to an average time of 72 hr per well for 15 wells recently completed.The major drilling problem on Barrow Island is surface hole drilling due to the very hard surface limestone combined with complete loss of circulation at sea level.In this operation, significant improvements have been effected. During the exploratory phase drilling, 12 1/4 in hole to set 9 5/8 in. casing, average penetration rate was 23 ft/hr. At the commencement of the development programme penetration rate, drilling 10 5/8 in. hole to set 8 5/8 in. casing, was 28 ft/hr for the 15 early wells considered, improving to 55 ft/hr for the 15 recent wells considered.This programme is a team effort and much credit must be given to the enthusiastic co-operation of the two drilling contractors.The current field record is 2 days 4 hr with a 4 1/2 hr move including the drilling of mousehole and rathole.

Jan 1, 1968

By R. K. Singhal, H. Sahay

Introduction In terms of the world's recoverable coal reserves, Canada ranks 10th, providing 0.6% of the world's total. The US is first with 27.8% and the Soviet Union follows with 24.1%. Figure 1 shows the principal coal mines in Canada. Several provinces contain substantial coal deposits, but the largest deposits are found in the western provinces of Alberta, British Columbia, and Saskatchewan. Conservatively, 90% of the lignitic, 80% of high volatile bituminous, and nearly 100% of subbituminous, and low and medium volatile bituminous coals are located in these three provinces. During the past decade, Canadian coal production of all types increased from 18.8 Mt (2 million st) in 1972, to 25 Mt (28 million st) in 1975, to 61 Mt (66 million st) in 1984. About 38 Mt (43 million st) of this output was classified at thermal and 23 Mt (25 million st) as coking and metallurgical coal (Table 1). The three western provinces currently produce 57 Mt (62 million st) of coal - 95% of Canada's total. The remaining 3.6 Mt (4 million st) (5%) is produced in Nova Scotia and New Brunswick on the east coast. The majority of western coal (98%) is produced by surface mining methods. On the east coast, though, mining is predominantly underground and only 15% is produced on the surface. In 1985, Canada exported close to 28 Mt (30 million st) of metallurgical coal and thermal coal. During the same period, 15 Mt (16 million st) of coal were imported, mostly from western US for use in Ontario and Quebec. Almost 60% of the imported coal was used for thermal applications. The remaining 40% was metallurgical coal for the steel industry. It is generally cheaper to import coal into central and eastern Canada from the eastern US to augment local supplies rather than from western Canada. This is mainly because of high transportation costs. Mining methods The suitability of mining methods in a particular area depends largely on the geological setting. Geology, therefore, simplifies or adds complexities to mining operations, directly affecting the economics. It also influences the flexibility required from the min-

Jan 9, 1986

By M R. Stevens

The Kauri Block (Hauraki Hill) andMatawai Valley epithermal vein systems, near Coromandel township, are hosted by hydrothermally altered Miocene andesites and Mesozoic greywackes of the Coromandel VolcanicZone. The hydrological setting of both geothermal systems was probably that of an andesitic volcanic arc. Two types of veins are recognised: 1. Simple veins composed of fine comb quartz, and 2. Complex (breccia) veins composed of vein fragments of sulphide-bearing, chalcedonic silica cemented by saccharoidal and fine comb quartz.   Pyrite, arsenopyrite, marcasite, and gold form the ore minerals. Both deposits historically exploited hypogene and supergene bonanza gold.   At Hauraki Hill, breccia veins up to 7m wide contain abundant fragments of recrystallised colloform banded-crustiform textured quartz veins ('Golden Cross' style) and were probably major channels for ascending deep mineralising fluids. Alteration assemblages are zoned with the higher elevations of Hauraki Hill-Bunkers Hill characterised by strong kaolinite alteration whereas deeper levels are dominated by illitic clays.   At Matawai, complex veins and hydrothermal breccias pinch and swell, and inflect, within a total width of veining and alteration that exceeds 50 m. The greywacke host rocks are altered to an assemblage of illitesmectite, quartz, chlorite and pyrite although there are pockets of kaolinite.   The proposed genesis of veins and ores in both deposits invokes episodic rapid mixing (quenching) of hot mineralising reservoir fluids with cool acid condensate waters, whilst acidification and increased fO2 triggered gold deposition. These hydrothermal systems heated up during their later stages and at Matawai visible gold was deposited from a late mesothermal stage. The main conclusion is that the northwest CVZ has excellent potential for large gold deposits (= 30 tonnes contained gold).

Jan 1, 1993

By R Soong

The Wharekirauponga (WKP) epithermal gold-silver deposit is located about 10 km north of Waihi in the Hauraki Goldfield east of Auckland. WKP is notable for its sheeted to stockwork quartz veins hosted in rhyolitic rocks, that have attracted exploration interest as a low grade, bulk tonnage exploration target. Exploration between 1978 and 1993 included 23 diamond drill holes totalling 5505 m. The mineralisation occurs in a rhyolite dome complex (Miocene), consisting of flow-banded rhyolite and rhyolitic pyroclastic rocks, with minor andesite. Fifty four drill core samples were collected from six exploration drill holes and analysed by semiquantitative XRD techniques. Hydrothermal alteration of the rhyolitic and andesitic rocks has developed secondary mineral assemblages of quartz, adularia, albite, chlorite, illite, sericite, interlayered illite-smectite, carbonate, halloysite and pyrite. The main zone of mineralisation is characterised by quartzadularia alteration, which grades oiItward to quartz-clay (illite, local halloysite and/or interlayered illite-smectite) alteration. Propylitic alteration is present at the southern end of the drilled area of the prospect. Depth-related changes in mineralogy include a decrease in illite and appearance and increase in quantity of chlorite with increasing depth, and the localisation of halloysite and interlayered illite-smectite in the shallow parts of some drill holes.

Jan 1, 2001

By M. R. Bitarafan

Mining method selection is the first and most important problem in mine design. In this selection some of the parameters such as geological and geotechnical properties, economic parameters and geographical factors are involved. The mining engineer must balance the input parameters and select the method that appears to be the most suitable; mining method selection is both an art and a science. Distinguishing all parameters that have an effect in mining method selection and in the determination of weighting factors of any parameter is a difficult task in an ordinary environment. This paper attempts to determine important parameters that impact on the mining method selection and demonstrates the calculation of the weighting factors for each selected parameter. This study has been directed to the research of a methodology for the selection of an optimal mining method. Different fuzzy methods are presented as an innovative tool for criteria aggregation in mining decision problems. Two methods of fuzzy multiple criteria decision making are used for selecting the optimal method with which to mine anomaly No. 3 of the Gol-Gohar iron mine. This paper finally presents a comparison of the selection methodologies and further discusses the most appropriate method investigated.

Jan 1, 2004