Search Documents

By A. Nkolele

Paper written on project work carried out in partial fulfilment of B. Tech (Metallurgical Engineering) degree Fine coal of the Goedehoop Colliery is dewatered by centrifuging before being sold. Full-scale plant tests were carried out to reduce residual cake moisture by the addition of surfactants. It is believed that by modifying the interface between the coal surface and the adherent surface water, as well as the water occluded in the cake voids, drainage is improved. Two anionic surfactants at concentrations up to 150 g/t were tested on coal of <0.5 mm size. The results demonstrate that quite high additions of surfactant (80 g/t)were needed to reduce moisture from 20 to about 17?18%. It was observed that when increasing surfactant additions at low levels, within a very narrow concentration range, the retained moisture first increased sharply only to decrease sharply immediately thereafter; this effect points to a critical surfactant concentration. Based on the obtained results, the use of surfactants cannot be recommended at this stage; further investigations under more controlled conditions are required.

Jan 1, 2004

By Erika Moonin, Jim Nickerson, Claudio Cimiotti, Roberto Bono

"In response to the severe drought on the Colorado River basin and in order to preserve existing water capacity to the Las Vegas Valley, the Southern Nevada Water Authority contracted a new deep-water intake (Intake No. 3) located in Lake Mead. The current project (Contract No. 070F-01-C1) includes 5 km (3 miles) of tunnel with very difficult geological conditions and a 200- m (650-ft) deep shaft and marine works. This paper will present the current status of the design-build contract being constructed by Vegas Tunnel Constructors and the challenges and problems faced and the innovative solutions developed to handle the difficult conditions encountered during tunneling with up to 15 bars of pressure.ProjectbackgroundThe Las Vegas Valley receives the majority of its water from Lake Mead, which is located approximately 30 km (20 miles) east of the Las Vegas, NV metropolitan area. Due to the severe drought that has hit the southwest region of the United States, the water level in Lake Mead has receded from its high water level of 372 m (1,221 ft) above mean sea level (amsl) to a low of 330 m (1,076 ft) amsl in June 2015. Should the lake level continue to fall, at elevation 320 m (1,050 ft) amsl, the current water intakes will not be able to draw enough water to meet the needs of the local area. The risk of losing water capacity has prompted the construction of a new deeper intake. Not only is the new Intake No. 3 situated at a lower elevation in the lake at 262 m (860 ft) amsl, the new Intake No. 3 is also located to draw better quality (Fig. 1).Project challengesThe project has had several difficult challenges to overcome:• The work consisted of a 1.2 kt (1,300 st) structure constructed on a barge and lowered 100 m (330 ft) into Lake Mead anchored with 9,200 m3 (12,200 cu yd) of tremie concrete.• The drill-and-blast starter tunnel was impacted by three inflow events, resulting in a one-year project delay.• One of the main challenges was selecting the tunnel boring machine (TBM) and excavating the tunnel with expected hydraulic head pressure of as much as 17 bar (16 bar was the highest pressure recorded during the drive), crossing faulted areas, low rock cover and the risk of tunnel instability due to direct connection with the lake.• Extensive pre-excavation grouting with a constant head pressure ranging from 12 bar to 15 bar.• Structural repair of the cutterhead in difficult hydrogeological conditions [water inflow of approx. 800 m3/hr (4,000 gpm)].• Complete repair of the cascade sealing system for the main bearing and two replacements of the pinion bearings.• The TBM approach to the intake structure."

Jan 1, 2015

By Roderick Eggert, Dipesh Dipu

We look at the empirical evidence of coal block auctions in India to understand how competitive intensity affects the bid amounts in common value auctions. The results suggest that competitive intensity measured through the number of bidders for a coal block is instrumental in determining the bidding outcomes. The presence of higher numbers of bidders in the auction leads to higher bids - every additional bidder causes the bid amount to rise by INR 142.67 per tonne of coal for auctions studied for 127 coal blocks from 2014 to 2023. The paper also examines the moderating and mediating effect of competition on bids and on excess of bids from the comparative market price of coal from alternative source of Coal India Limited. The results indicate that competitive intensity does not have statistically significant impact on the relationship between common value of coal blocks and bids, neither as a moderator nor as a mediator. The strategic behavior of the bidders has also been observed as bidders have been seen to bid in a higher than market price in order to outbid the competitors.

Feb 1, 2025

By Walter Murphy

For a number of years the Bureau of Mines has been studying the properties of crude petroleums produced in the United States and the Western Hemisphere. A number of reports have been published giving the analyses of crudes from the different field and regions as made by the Bureau of Mines Hempel method of analysis.4/ Several of these reports include analyses off crude oils from the Rocky Mountain region.5/ The search for new fields and new producing horizons in old fields in the Rocky Mountain region has been quite intensive during the last few years, and a number of discoveries have been made.

Jan 1, 1937

By J. W. Wilson, P. C. Graham

SUMMARY The Witwatersrand quartzites in which South African gold mining operations are moat exclusively conducted, are notoriously difficult and costly to drill. Despite this situation, however, with the high cost of developing new mines and extending existing mines, together with the rising cost of labour and mining problems resulting from the ever-increasing depths of workings, the demand for raise-boring in these formations is increasing rapidly. Not only is the demand for raises and shafts increasing, but also the length and size of these excavations. Raise-boring studies carried out in South African gold mines have indicated that increased penetration rates and possibly reduced costs could be obtained if higher thrusts were available at the reaming head. Until fairly recently there has been no raise-boring machine suitable for underground use that possessed the thrust and torque characteristics necessary to achieve high penetration rates in hard abrasive quartzite formations and the cutters available were not really developed for high loading. In response to these requirements a raise-borer, the Robbins 83R was designed and built in Seattle, U.S.A. for the Anglo American Corporation. This machine is operating in South African gold mines and is currently being used at a depth of 12 000 ft below surface in one of the. Group&apos;s mines. The initial raises bored have substantiated that increased penetration is attainable at high thrust and it is now apparent that the machine is sufficiently versatile to drill raises of up to 12 ft in diameter in quartzite formation over a length of 2 000 ft.

Jan 1, 1974

THE Talisman mine is situated on the Waitawheta (pronounced Wytaffetta) river just above its junction with the Chinemuri (pronounced Chinnemurre) river near Karangahake, NZ. The explored reef-bearing portion of the claim includes the angleformed by the junction of the rivers and extends southwards for slightly over a mile (See Plate V.). The country is mountainous both rivers flowing through precipitous gorges.The trig. station on Karangahake mountain is almost directly above the workings on the Bonanza section and is 1680 ft. above river level, the adit from the gorge giving 1200 ft. of backs measured vertically. The officers of the N.Z. Geological Survey are engaged in a detailed survey of the Waihi district and the rocks of Karangahake are under examination. The rocks of the district are andesites and dacites much altered and silicified. One of these exhibits a columnar structure in the mass in the Waitawheta gorge near the surface workings on Taukani hill, also on the southern bank...

Jan 1, 1912

By C J. Adams, H J. Campbell, A J. Tulloch, I J. Graham

New Zealand can be regarded as a rifted part of mineral-prospective eastern Australia. Geologically credible comparisons between selected trans-Tasman and SW Pacific geological provinces and units, especially those that contain significant mineralisation in Australia, can help provide a useful exploration framework for New Zealand. As part of a six-year Mineral Wealth of NZ and its EEZ (MWE) research programme, we have targeted selected geological units in eastern Australia for comparison and contrast with their potential New Zealand counterparts. In future years, the programme will focus on geological units in New Caledonia.

Jan 1, 2005

By George A. Costello

A theoretical analysis is presented for the static and dynamic response of wire rope in deep-shaft mining operations. Expressions for the stresses in the individual wires of complex wire ropes are derived, and specific results for simple strands, 7x7 ropes, 6x 19 Seale ropes both with and without internal-wire-rope cores, and 6x25 filler-wire ropes both with and without internal-wire-rope cores, are presented for the case of ropes subjected to a combination of axial loading and bending over a sheave. Consideration is also given to the dynamic overloading associated with certain mining operations, such as dumping ore into a suspended skip and accelerating a fully loaded skip upward. Experiments to determine the axial stiffness of wire rope are described. Factors affecting the service life of wire rope, such as residual stresses, contact stresses, and fatigue behavior, are discussed. Specific research areas in need of further investigation are identified.

Jan 1, 1983

By James S. Graham

Foundation pile driving hammers used in New York City in the past 100 years have been drop, steam, compressed air, diesel, and hydraulic. In 1992, the first hydraulic hammer in the New York City area was purchased by Norwalk Marine Contractors, Inc. from Junttan in Finland. It was bought because of its variable energy and ease of mobilization, not because of its higher transferred energy. Heller and Johnsen engineers instrumented hydraulic hammers on nine jobs. The measured transferred energy for the nine jobs was found to average approximately 80 percent. There is no clear consensus regarding the reasons for the hydraulic hammer being more efficient in delivering energy to the pile as compared to single-acting steam/air impact hammers. To minimize pile damage during installation, and to minimize footage overruns, an up-to-date version of the wave equation software that includes an efficiency value of 0.95 for hydraulic hammers is now used.

Jan 1, 2000

By Greg Sheppard, Eduardo Nebot

Australian researchers have developed new technologies aimed at improving safety and productivity at openpit mines. A data acquisition and feedback system for electric rope shovels has been shown to substantially reduce cycle times and decrease excessive machine duty caused by stalls. This data acquisition system was developed by the Cooperative Research Center for Mining Technology and Equipment (CMTE). It has been tested on a P&H 4100A shovel at Coal & Allied’s Hunter Valley operations and a P&H 4100XPB at BHP Billiton Mitsubishi Alliance’s Goonyella Riverside Mine in Central Queensland. In addition, CMTE member P&H Mine Pro Services has used the technology to acquire field data from a P&H 4100XPBrope shovel at RAG’s Belle Ayr Mine in Wyoming’s Powder River Basin.

Jan 1, 2002

By P. Choquet, F. Miller

"The development and testing of a simple low-cost gauge for measurement of tension in a cable bolt grouted in a borehole are presented. Its principle is based on a resistance wire which is wound on a 70 cm length into the spiral grooves of the wire strand cable bolt. Readings are then taken by a robust automatic data logger with a several day autonomy or by a portable readout. In order to have a complete profile of tension along the cable bolt, a number of tension gauges can be installed along its length.This paper provides a description of the development and laboratory calibration of the tension gauge and addresses the two modes of loading for a cable bolt in a rock mass, namely pure tension and shearing at a joint location.In the second part of the paper, four field tests in underground and open pit mines are reported. The first test was used to substantially modify both the gauge and the readout unit principles while the other tests which are still on-going show a very satisfactory behaviour of the modified version of the tension gauge. IntroductionCable-bolting is often used as ground support in Canadian mines for a variety of applications. In underground mines, cable bolts can be installed vertically at the back of cut and fill stopes or in an inclined fashion in the walls of large open stopes. Alternatively, cable bolts at Mines Gaspe (Noranda Inc.) are used in a fan-shaped pattern from a drill drift to stabilize the inclined roof in 25 m wide open stapes. This new application oriented our research efforts toward the design of a novel instrumentation to monitor the efficiency of most commonly used 5/8-inch cable bolts."

Jan 1, 1988

By D. S. Richards

Computers have revolutionized the collection of data on modern mines. Never before has it been possible to collect data from all aspects of the mining value chain at rates now common. With this has come a new challenge. Deriving information from these copious amounts of data and disseminating it. This problem is being exacerbated by technical software systems, which use proprietary and binary data formats that severely inhibit the flow of data and information both across departments and the larger organization. Generally this had led to data duplication and data redundancy. The Gemcom Enterprise Mining System (GEMS) makes use of industry standard, secure and open databases for all its data objects. It manages multiple users accessing the same bits and bytes in the database, preventing data duplication and redundancy. Developed in the Microsoft BackOffice ® environment, GEMS is also able to leverage the enormous amount of tools available in this environment, whether it’s for e-mail notification, reporting or data capture. Microsoft’s® Active Server Pages are one of these tools. These are standards used to create dynamic and interactive web pages with links into databases and many other objects. The real example outlined in the text, demonstrates how a user anywhere in the world is able to login to a web page and run a query that returns a report with vector plots of performance for the user-selected time frame. As integration is tightened between the various components of the mining value chain, the importance and reliance on ASP pages will grow as the need for management information tools develops. Keywords: mines, computers, ASP, GEMS, integration, Microsoft, Management Information.

Jan 1, 2003

Very little has been written about the discovery and early history of prospecting of ironstone deposits in the Iron Knob-Middleback Range area of South Australia, the main source of supply of ironstone (hematite) for the Australian steel industry, and scanty though the record is, much of it is wrong or misleading.With the help of several people, to whom acknowledgement is made at the end of the paper, the writer has unravelled some of the story, but not the whole story. It is hoped that publication of this paper will stimulate interest in others, who may be able to supplement this account from family records, from the files of newspapers, or from archives.

Jan 1, 1969

By Roy E. Peterson

The Bureau of Mines conducted bench-scale research to evaluate materials which showed potential as low-cost reductants for use in the ironmaking industry. These materials were lignite, subbituminous coal, coal char, tree trimmings, refuse--derived paperboard, used crankcase oil, and peat. To compare their effectiveness, the materials were tested in the reduction roasting of nonmagnetic taconite and, except for oil and peat, in the reduction of iron oxide pellets to metallized pellets. Reduction was conducted in a 18-cm-diameter, rotary drum, which was externally heated in an electric furnace. Over 92 pct of the iron was magnetically recovered from a nonmagnetic taconite after roasting with any of the reductants, but greater quantities of reductant were required to achieve this when the waste materials were used. The fossil fuels were also more effective for metallizing pellets, although metallizations above 90 pct were also obtained with tree trimmings and refuse paperboard. However, refuse paperboard had to be frequently recharged to the furnace because it depleted rapidly.

Jan 1, 1983

By B. Clermont

Ball mills are usually the largest consumers of energy within a mineral concentrator. Comminution is responsible for 50% of the total mineral processing cost. In today?s global markets, expanding mining groups are trying to optimize mill performances. Since comminution is concerned with liberating valuable minerals for recovery in the separation process, it is crucial to run the mills at the best operating conditions which lead to good liberation at competitive throughputs with minimum costs (energy and wear). The high availability of the equipment is also essential to maximize production and profit. To reach this key objective, continuous and reliable information about the mill operation is vital. An innovative tool which can deliver information about in-mill dynamics has been developed by Magotteaux. It can provide online and accurate measurements of the degree of grinding ball fill and pulp position for timely decision making and actions. This tool could be used on its own or linked to an automatic grinding ball loading system named Magoload. Therefore, ball load could be kept constant by using direct measurement. This article describes the Sensomag and presents some of the major improvements that can be achieved with it. Some other promising avenues are still to be explored. Keywords: Comminution, process control, process optimization, process instrumentation, online analysis.

Jan 1, 2010

By George L. Gates

[When clays are mixed with water to -.,tee mud fluids for use in trilling wells for nil and --ac b ;l-,e rotary method the liquid mixtures have certain physical characteristics that vary with the quantity and size of their inherent solid particles. All naturally occurring clays contain variable quantities of particles of different sizes ranging from relatively coarse (sands) through -,.tedium (silt) to fine materials of colloidal dimensions. Tie colloid content is extremely important 2.s a desirable _.&apos;ale constituent of mud fl-z to fit well drilling. &apos;;&apos;it:-out colloids the souk?;,&apos; in a mud fluid wouldr rapidly, end ti-c-and. wall-building qualitites of the&apos; fl,-,id would l ..o r re 1 impaired. Mud .fluid.^ with insufficient quantities of colloids also are lacking in "lubricating" g listen, and it is, to ° min casing in, -)re holes drilled with such fluids.]

Jan 1, 1941

This Bureau of Mines publication presents five papers given at a Technology Transfer Seminar on Metal Mine Fire Protection Research. Several seminars are held each year to bring the latest results of Bureau conducted and sponsored research to the attention of the mining industry as quickly as possible.

Jan 1, 1977

By Terry J. Close

U.S. Bureau of Mines personnel studied the 33,900-acre Silver Peak Range North Wilderness Study Area (NV-060-338), in order to evaluate its identified mineral resources. The area studied lies between the towns of Silver Peak and Dyer, about 40 miles southwest of Tonopah, in Esmeralda County, Nevada. There are no producing mines in the area studied. However, development of Sunshine Mining Company?s Sixteen-to-One silver-gold mine, located in the Silver Peak mining district near the eastern edge of the study area in the early 19801s, has stimulated recent interest. The Sunshine Mining Company claimed two sites within the study area in 1985. Also, Intermountain Resources, Incorporated, located a group of claims at a prospect along the west side of the study area in the Dyer mining district, and in 1986, began drilling. Other claimants are holding two other claim groups by assessment. At the five currently (1987) held sites, precious metals occurrences are being investigated. There are no patented mining claims or mineral leases in the study area.

Jan 1, 1987

By P N. Holtham

Magnetic separation is routinely used in the processing of titaniumminerals, and the efficiency of these operations can be determined bymeasuring the magnetic properties of the process streams. The valuable components in the feed to a titanium minerals plant have specific magnetic susceptibilities ranging from -10-9 m3 kg-1 (zircon) to 10-6 m3 kg-1 (ilmenite). However, in an industrial environment, in which the mineral temperature may range from 20 to 120¦C, it is difficult to measure susceptibilities lower than about 10-7 m3 kg-1. Hence laboratory testing of spot samples from magnetic separators is currently required to obtain accurate performance data. This is an inherently slow process and where feed grades are variable, optimum performance of magnetic separators is generally not achieved.This paper describes the development of an inductance-basedinstrument for measuring very low levels of magnetic susceptibilityon-line. The signal from the instrument can be used for process control purposes to maintain optimum magnetic separator performance.A prototype instrument has been installed in the zircon scavengercircuit in an Australian titanium minerals plant. The circuit consists of a roll magnetic separator treating a feed consisting mainly of monazite and stained zircon. The monazite-rich magnetic fraction is returned to the mine site for disposal, while the non-magnetic fraction is recycled to the zircon wet circuit. Splitter positions in the separator are adjusted when the final zircon product fails to meet specification, or the magnetic fraction contains more than 30 per cent zircon. Weekly composite grain counts show that sub-optimal operation of the magnetic separator results in significant zircon losses into the magnetics fraction.Using the instrument, the zircon content of this stream can now beaccurately determined from the measured magnetic susceptibility,provided a correction for the effect of mineral temperature is applied using the Curie - Weiss relationship.

Jan 1, 2001

By Clifford Britch

"Kaiser Resources Ltd. has completed feasibility studies resulting in approval of $277,500,000 for the construction of the Greenhills Surface Coal Mine, located 35 km north of Sparwood, B.C. The mine is designed to produce 1,800,000 tonnes per year of metallurgical coal over a 20-year period by conventional truck /shovel methods.The project is in the detailed design phase, with some preparation work being carried out on the site. The major construction activities are scheduled to commence in the spring of 1981. Mine development and pre-stripping will commence in July 1981, with first coal production scheduled for mid 1983.This paper will be a general description of the project and will include a discussion of the geology, reserves, mine planning, coal handling and processing, surface facilities and related topics.IntroductionProject DefinitionThe Greenhills Project is designed to produce, by conventional truck I shovel surface mining methods, 1,800,000 clean tonnes of metallurgical coal per year for twenty years . The production/ life constraints were chosen as being meaningful for planning and evaluation purposes after appraisal of the market potential and are not limited .by economic reserves. Substantial additional strippable reserves are available which would facilitate expansion of the proposed mine life and/ or capacity. In fact , all the facilities are designed so that they can be expanded in the future to accommodate a doubling of annual coal production, and certain portions of the coal processing facilities are being installed with an annual capacity of 3,600,000 tonnes. The mine will also produce approximately 2,400,000 clean tonnes of oxidized thermal coal, mostly in the first decade."

Jan 1, 1981