Search Documents

By J. Tanner Blackburn, James R. Gingery, Lisheng Shao

Rigid inclusions consist of grout columns installed using displacement auger or vibrated tooling. The columns are typically installed in an array to provide support for footings, mats, or embankments. Due to the relative small column diameter and low replacement ratio, the surrounding soils typically have minimal densification or improvement. A gravel load transfer platform is commonly used above the rigid inclusion head to distribute stresses more broadly to the supported structure. The axial stiffness and geotechnical engineering mechanics of rigid inclusion design are similar to those of deep foundation systems, but they are typically only lightly- or un-reinforced and are not structurally connected to the above-grade structure. The popularity of rigid inclusions is increasing in the Western U.S., where many urban areas are subject to moderate to high seismic hazard levels. However, the performance of rigid inclusions under seismic loading is poorly understood, and seldom addressed in current designs. The elements are brittle, with limited or no ductility and relatively low moment capacity, and therefore may be prone to damage under seismic loading. Three modes of seismic loading should be considered: inertial loading from the structure, kinematic loading from vertically propagating shear waves, and kinematic loading from ground failure- related permanent ground deformation. This paper focuses on the first two modes. A simplified procedure for evaluating kinematic and inertial loading of rigid inclusions is described, and its use is illustrated through application to a site in Southern California. The results show that moderate to severe kinematic loading can generate plastic hinges in the rigid inclusions. Engineering consequences of this hinging could include settlement or bearing failure. INTRODUCTION In this paper the term ‘rigid inclusion’ (RI) refers to grout or grouted aggregate columns that are installed using either drilled or vibration displacement techniques. They are commonly installed in arrays to support vertical loads from footings, mats, or embankments. RIs are not structurally connected to footings they support. Rather, it is typical for a dense gravel load transfer platform (LTP) to be installed as a cushion between the RI head and supported footing or new fill. In cases of RI support of fill embankments, the LTP may be reinforced with horizontal layers of geogrid.

Jan 1, 2018

ALTHOUGH great progress has been made in flotation of the Broken Hill silver-lead-zinc ores, no paper dealing with this subject has been presented to the members of the Institute since James Hebbard's valuable contribution in 1913. Almost every discovery or development in the history of flotation has formed the basis 6f a patent, and but few experimentalists have overlooked the fact that their investigations might lead to the establishment of a patentable process. This, together with the aftermath of patent litigation, naturally resulted in secrecy being maintained in matters appertaining to the art, and the industry as a whole has consequently suffered considerably. Much valuable time has been wasted through numbers ofmen repeating work along certain lines, which, unknown to them, had already been thoroughly exhausted by others, whereas a lot of this would have been avoided by a freer interchange of information amongst those directly concerned. Owing to differences in the ore treated and the various applications of flotation concentration in relation to gravity methods, the flotation problems of the various mines differ considerably. This, together with the secrecy previously referred to, hasresulted in the development of numerous systems and machines, most of which would appear, to the casual observer, to comprise separate and distinct processes. The author has endeavoured to show how much these processes have in common with one another, and, at the same time, has tried to convey some general ideas on flotation to those members of the Institute who are not directly associated with this branch of concentration.

Jan 1, 1919

By S. Al-Thyabat

Conditioning of flotation feed is an important prerequisite for efficient flotation. This process depends on parameters such as conditioning time, slurry concentration and slurry pH. The objective of this paper is to optimize the conditioning process for the flotation feed. This was achieved by first conducting preliminary experiments at constant slurry pH to determine the significant ranges of slurry concentration and conditioning time. Then, factorial experimental design (32 experiments) was used to investigate the significance of the above parameters and their interactions on flotation recovery and grade. Statistical analyses using ANOVA approach showed that flotation recovery (R) and concentrate grade (g) were affected by feed conditioning. It was found that concentrate grade was linearly proportional to the slurry concentration and conditioning time, while flotation recovery was exponentially proportional to the conditioning parameters. A contour plot of the flotation response (recovery and grade) against conditioning parameters showed that the optimum operating parameters for flotation feed conditioning was a conditioning time of 1.5 to 2 minutes and a slurry conentration of 55% to 60%.

Jan 1, 2008

By James W. Weaver

The 2,120-foot long cable stayed Penobscot Narrows Bridge that carries US Route 1 over the Penobscot River between Verona Island and Prospect, Maine is supported on four foundation units, one below each pylon and one at each abutment. Due to varying subsurface conditions along the bridge alignment, the structure was designed to be supported on foundations consisting of high-capacity steel H-section piles (Verona Pylon), a mat bearing on a prepared bedrock surface (Prospect Pylon) and spread footings bearing on compacted rockfill (abutments). The 70-foot by 80-foot (plan area) Verona Pylon foundation was designed to be supported by 288, 430-kip design capacity steel H-section piles (HP14x117, 50 ksi steel) driven through up to 100 feet of dense glacial till deposits containing cobbles and boulders up to 3 feet in diameter. The piles were installed using a single-acting diesel hammer (Delmag D62-22) with a maximum rated energy of 165 kip-ft. Thirteen representative piles were selected for dynamic testing (ASTM D-4945) to verify pile capacity, hammer efficiency and pile stresses. Dynamic testing determined that four different pile driving criteria were needed across the site due to variation in the bedrock and soil resistance below the footing plan area. Approximately 4 percent of the production piles were damaged/rejected due to misalignment and/or damage as a result of encountering the cobbles and boulders embedded in the glacial till. The rejected piles were located randomly throughout the plan limits of the foundation mat. Subsequent structural analyses indicated that the foundation was capable of safely supporting the design loads without the need for installing replacement piles. Evaluation of dynamic testing results with signal matching and pile driving records provided valuable information on pile side and tip resistance. Evaluations were made regarding predicted versus actual pile lengths, pile bearing material, distribution of skin friction and end bearing capacities.

Jan 1, 2011

By B M. Washington, R R. Lovel, G J. Sparrow, M J. Fisher-White

"Work in CSIRO with several Australian ores has shown that?by heating a high-phosphorus goethitic iron ore and then leaching with caustic or acid, the phosphorus levels in the ore can be lowered to a commercially acceptable value of around 0.08 weight per cent phosphorus (P). With increasing heating temperatures up to 1300¦C, the extent of phosphorus removal increased. This is considered to be associated with mineralogical changes in the iron oxide phases in the ore during the heating.Little phosphorus was removed from four high-phosphorus goethitic iron ores containing 0.12 - 0.16 weight per cent P in leaches with boiling water. However, leaches with sulfuric acid removed ten to 20 weight per cent of the phosphorus and leaching with sodium hydroxide removed even more phosphorus to produce leach products containing between 0.08 and 0.12 weight per cent P from three of the ores.After heating at 300¦C, leaches at a low pulp density of 0.5 weight per cent solids with 1 - 5 M NaOH and 0.1 - 1 M H2SO4 gave leach products with 0.06 - 0.09 weight per cent P. The lixiviant concentration required and extent of phosphorus removal depended on the ore. At a higher pulp density of 25 weight per cent solids, leach residues with between 0.07 - 0.14 weight per cent P were obtained.More phosphorus was removed from ores heated at 900¦C. Leaches at both the low and high pulp densities, with 1 - 5 M NaOH and 0.1 - 1 M H2SO4, gave leach products with 0.05 - 0.09 weight per cent P. However, the lowest phosphorus levels were obtained after heating the ores at 1200 or 1300¦C and leaching with 1 M NaOH or 0.1 M H2SO4. Leach residues with 0.02 - 0.06 weight per cent P were obtained, even from leaches at the higher pulp density of 25 weight per cent solids. Leaching tests on heated samples under heap leaching conditions at ambient temperatures have shown that phosphorus levels can be reduced to similar levels to that achieved in an agitation leach within ten days.CITATION:Fisher-White, M J, Lovel, R R, Sparrow, G J and Washington, B M, 2013. Effect of temperature on removal of phosphorus from Australian Goethitic iron ores, in Proceedings Iron Ore 2013, pp 373-380 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

By Y. C. Kim, I. S. Roditis, P. K. Medhi

P. Mousset-Jones I found the article most interesting and timely. I consider it imperative that mine case studies like this one are undertaken and published so that the practicing mining engineer and geologist can obtain a better idea of what is the preferred estimation and grade control technique to use, given the site-specific geology, grade distribution, etc. Mining companies, with operating gold mines, need to be encouraged to either initiate such a study in-house or support a research project by financing a graduate student at a local university. The latter method is preferable since it not only provides research support but also an excellent training opportunity for young mining engineers and geologists. Ideally, what is needed is exploration drill-hole, blasthole, and mine production data that can then be used to assess the efficiency of different estimation and grade control methods by comparing the results obtained using the drill/blasthole data with the actual production data. It is hoped that more mining companies will realize that the rewards from this kind of research greatly outweigh the sometimes perceived problem with releasing data to a university. I noticed that the authors used the blasthole data to represent the actual values, the validity of which relies heavily on the two key assumptions with regards to blasthole assays and in-pit ore-waste selection procedures. Could the authors comment in more detail on these assumptions and what criteria they used to check the validity of the assumptions? Since the article was published, have the authors had the opportunity to compare their estimates with the actual production data? It would be interesting to compare other estimation methods with OK and IK. For example, how well did the polygonal method used at the mine compare with the results given in the paper? I would like to mention that B.L. Kwa completed a similar study (Kwa and Mousset-Jones, 1986) using exploration drill-hole, blasthole, and production data from the Alligator Ridge mine in Nevada. The study compared a variety of estimation methods, including IK, and the final results are shown in Fig. 1. The IK method exhibits the smallest difference between estimated and production results and is closely followed by the indicator moving window (Ind MW) method. Reference Kwa, B.L., and Mousset-Jones, P., 1986, "Indicator Kriging Applied to a Gold Deposit in Nevada," Proceedings, Symposium on Ore Reserve Estimation Methods, Models, and Reality, CIMM Annual Meeting, Montreal, Quebec, Canada, May, pp. 185194. Reply by Y.C. Kim We do concur with Professor Mousset-Jones with respect to the merit of such case studies performed at a local university. In answer to his request for comment on the validity of the two key assumptions made in our paper, we can only say that these are reasonable assumptions that are very difficult to validate. The assumption of blasthole assays being accurate can be partially validated by a careful analysis of the nugget component of blasthole variograms. The assumption that the in-pit ore-waste selection procedure in use was an effective one can only be validated through comparison between the mine estimates of ounces of gold versus the actual recovered ounces of gold at the mill. Neither one of these two assumptions has been validated to date due to several reasons. For example, the mine went through a change in management since the study. Similarly, no compelling reasons have been presented to perform detailed variogram analysis of the blasthole data. We do, however, believe that the obtained results (i.e., indicator kriging performs better than OK in a highly skewed deposit) will remain the same in relative terms, regardless of how valid these two assumptions may be. The most recent comparative study by D. S. Lindsey of the Montana College of Mineral Science and Technology also shows a similar ranking between ordinary kriging versus probability kriging, which is an extended version of indicator kriging. Reference Lindsey, D.S., 1987, "A Comparative Study: Probability Kriging vs. Ordinary Kriging at the Golden Sunlight Mine," MS Thesis, Department of Mining Engineering, Montana College of Mineral Science and Technology, Butte, MT, May, 81 pp.

Jan 3, 1988

By Yi-Shen Li

This report has been prepared by Lockheed Missiles & Space Company, Inc. (LMSC), under United States Bureau of Mines Contract No. H0220040 dated 21 June 1972 for the design, development, fabrication, and certification of the One-Hour Self-Rescue Breathing Apparatus (PBA). The PBA is a self-contained, oxygen-generating, CO2-removing closed-loop breathing apparatus that provides a minimum of 1 hour of breathable atmosphere during escape from a mine with a contaminated or oxygen-deficient atmosphere. This Cost-Plus-Fixed-Fee (CPFF) contract has been successfully completed in a three-phase program. The Phase I tasks included the design, development, and fabrication of prototype units developed at LMSC in accordance with the requirement of the Code of Federal Regulations (CFR) Title 30, Chapter 1, Subchapter B, Part 11 (Appendix A), and was submitted to the National Institute for Occupational Safety and Health (NIOSH) for joint NIOSH and Bureau of Mines certification testing.

Jan 1, 1974

By D. Harrington, W. J. Fene, H. B. Humphrey

In the fiscal years 1946 and 1947 the number of mine explosions decreased compared with the preceding years. However, the loss of life was so serious during the fiscal year 1947 the period when the Government administered bi- tuminous-coal and lignite mines that from April to June 1947 extraordinary measures were taken in mines then under Government possession to obtain com- pliance with provisions concerning rock dusting, ventilation, and blasting that had not been followed. The great loss of life in explosions during the fiscal year 1947 as compared with 1944, 1945, and 1946 is not easy to explain, but the necessity for maintaining adequate protection has been definitely demonstrated. Management, workers, and inspection agencies alike must keep the mines reasonably safe against explosions or allow them to lapse into a condition where chance is the principal protection against disaster. The at- tention given to protecting coal mines and the men employed in them against mine fires, following the disastrous fires in 1944 and 1945, has at least tem- porarily controlled this hazard loss of life from coal-mine fires was re- duced to 1 fatality in 1947. The number of fires was also less, and progress has been made in reducing the heavy losses in both life and property from un- derground coal-mine fires that occurred in the two years mentioned. Fatalities from mine explosions during the past 6 fiscal years, July 1942 to June 1947, totaled 674, and there were 149 explosions; during the preceding 6 years there were 655 fatalities in 132 explosions. The 6 fiscal years 1942- 47 cover the active period of Federal coal-mine inspection. During the fiscal year 1947, there were 154 fatalities from explosions compared with 58 during the fiscal year 1946, 64 in 1945, 94 in 1944, 152 in 1943, and 152 in 1942.

May 1, 1948

By Drupad B. Desai, Bruce Chang, Jay L. Merritt

This paper reviews difficult ground conditions encountered along the alignment of large-diameter sewage tunnels for the City of Los Angeles. It offers a detailed one-of-a-kind solution to a unique problem for shallow urban underground tunnels in a seismic zone, using state-of-the-art materials, technology, and equipment. The following topics are discussed in detail: • Geotechnical Design consideration for tunnel traversing through an active fault zone. • Seismologist evaluation of possible fault-offset problems where a fault zone crosses the alignment, in the event of an earthquake of moment-magnitude 6.5. • Probability analysis regarding "recurrence interval." • Structural design of tunnel subjected to displacement, subjected to axial elongation or shortening, and capable of rotational freedom. • Special joint details.

Jan 1, 1989

By Hou Shitao

With the development of Wuhan's city planning in China, new buildings of moderate and high store have been increasing day by day. Precast concrete piles or cast-in-site piles were used in the major foundations of the buildings. In process of their design and construction geotechnical engineers are concerned very much about practical bearing capacity and construction quality of pile foundations. In order to grasp accurately the cases static loading or vibration test is used generally to judge them. At present, the major questions in existence are that although a load is applied directly on pile and measured datums are reliable for static loading test, it must take a lot of work and longer time and engineering cost is higher. A vibration test has the advantages of which checking up of pile quality can be performed rapidly, the test is simple and convenient, and scope measured wide. But bigger error exists generally in measured datums. Therefore, it is nesessary to make vibration test on piles more perfect for pile foundation engineering. It is stated in paper that adapted technique of vibration test on piles is quite right in developmental direction sense for pile foundation. There are a great variety of vibration test methods on piles. A few of methods which often are adapted in practice can not meet the need of different practical engineering. It is also an important question whether the instruments of vibration test and relevant computer softewares make a response accurately for practical case. Different sequence of operation and technical requirements comes into being some influence directly on the test results. Meanwhile, different combination of soil stratigraphy, soil texture, groundwater and pile could cause different error of test datum. It is necessary to analyse and judge objectively the results of vibration test. Therefore, on the basis of developing and perfecting further the technique of vibration test, the applied technique of vibration test should be standardized so that better test results can be obtained.

Jan 1, 1991

By R R. Large

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The formation of orogenic gold deposits is commonly a two-stage process. The first stage involves preconcentration of gold in a suitable source rock, such as carbonaceous black shales, felsic volcaniclastics or komatiitic volcanics. The second stage involves the release of gold (commonly with arsenic and/or tellurium) from the source rocks during metamorphism or magmatic intrusive events, accompanied by the replacement of source rock pyrite by pyrrhotite. Recent research suggests that synsedimentary gold trapped in the structure of diagenetic arsenian pyrite in reduced carbonaceous facies of continental margin sedimentary basins is an ideal source of gold for many orogenic and Carlin-style gold deposits. The conversion of diagenetic arsenian pyrite to pyrrhotite during basin closure and greenschist facies metamorphism is the key process releasing gold and arsenic to the metamorphic fluid, with metal deposition in structural trap sites to form the deposits.CITATION:Large, R R, 2015. Orogenic gold deposits – a two-stage process of gold enrichment, in Proceedings PACRIM 2015 Congress, pp 335–340 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By J. Hu, F. Lin, R. Chen, F Peng, S. Yang, W. Yu

"Microseismic monitoring technology has become one of the most effective method of mine ground pressure monitoring after decades of development. But safety assessment of mine ground pressure by using microseismic monitoring is still in the development stage, it needs to be perfected continuously in practice, and choose the optimal assessment indexes and methods. The definitions and physical meanings of wave velocity, b value, and EI-VA value are introduced in this paper. Statistical calculation of the microseismic events in Luomu Mine is finished by using these indexes, then the functions and calculation results of V, b value, and EI-VA value with the variable of time are also given in the paper. The preliminary safety assessment method is established in Luomu Mine, and it has achieved good results in practical application.1.1 Engineering background The Luomu Mine is a super large molybdenum and tungsten production base in China, ore reserves is up to 2 billion tons, first in Asia and third in the world. It begins mining since the 1960. and bases on underground mining until 2002. In order to recover resources more effectively, it began to use opencast mining method and formed a production of 30000t/d in the early 1990. After about 30 years of underground mining, a large mined out spaces was formed under open pit mine, up to area of 1.2 million m2 and volume of 18 million m3, as shown in figure 1. The large number of mined out spaces seriously affects the normal production, mining and handling of mined out spaces are in the high risk. In the past years, several rock mass collapsions happened, and it caused a serious security threat to persons and equipments. According to the distribution characteristics of mined out spaces, Luomu Mine is divided into A, B, C, D and E mining area. The stability of D mining area is studied in this article. D mining area mainly includes 1376,1350,1340,1317 mined out spaces and 1280 deep large mined out area, as shown in figure 2. The mined out spaces of D mining area is extremely complex and high-risk. Therefore, a microseismic monitoring system was built to monitor the stability of D mining area, a large number of valuable datum has been obtained, and it has a striking effect (Cheng & Peng, 2013; Peng et al., 2013)."

Jan 1, 2015

By William H. Hamilton

INTRODUCTION It was not very many years ago that tunneling machine manufacturers spent considerable time trying to convince contractors and mine operators of the advantages of mechanical tunnel boring over conventional drill and blast methods. Today there are few doubters left. There is universal agreement that, not only are tunneling machines here to stay, but the ratio of bored rock tunnels to blasted rock tunnels is increasing at an accelerated pace, and within the next twenty years I predict almost all tunnels will be bored by machine. I believe we are today at a very important mile-post in the development of tunnel boring systems. Felix Gaye stated in his recent article (1) "It is important to disseminate between the efficiency of cutting tools and the overall efficiency of the boring operation". Mechanized tunnel boring in the past placed almost total emphasis on the rock cutting and boring ability of the tunneling machine. With advancements in technology and better solutions to the problems of rock fracture, steering control, and structural design, the emphasis today can be placed on the total-system concept. Tunneling machine design, as one of the key elements in the overall system, presents many problems that are not totally solved today. These design problems are, in the most part, not related with rock fracture, but rather with criteria associated with the over-all operation.

Jan 1, 1997

By Y. K. Yen, J. D. Miller, C. L. Lin

The image-based On-line Particle Size Analyzer (OPSA)system has been developed at the University of Utah to measure particle size distributions under plant conditions where overlapped and segregated particles are being transported on a moving belt conveyor. Evaluation of the OPSA system at several plant sites has been completed. The results show a consistent agreement between the particle size distributions obtained from the OPSA system and those obtained from laboratory screen analysis of belt samples. These results and the stable performance of the OPSA system during the field tests suggest that continuous quality control of crushed products is possible using the OPSA system.

Jan 1, 1999

By F. De Lucio

Para la aplicación de la instalación de un sistema de relleno hidráulico es necesario evaluar las funciones que el relleno debe contener y determinar si el material a usar cumpla con las funciones especificadas. En ese sentido, el objetivo del texto presenta una interpretación científica sobre tal método para especificar las funciones que el relleno deba cumplir y la metodología experimental adecuada que evalúe cuantitativamente a un relleno hidráulico.. Asimismo, se describen sus propiedades estructurales como la densidad relativa, reducción de volumen y estabilidad de tajeos contínuos, así como los métodos indirectos para inferir dichas propiedades y las posibles consecuencias secundarias que pueda generar el empleo de relleno hidráulico.

Nov 20, 1972

By Tanner A. C, Harraway D. H

Various circuits were tried at Mount Isa Mines during the period 1959 to 19G3 with the objective of improving the differential flotation of galena and sphalerite. Many benefits and disadvantages of the various circuits were revealed. An analysis' of ore characteristics and their effect on flotation was made -and resullted in the design of a proposed circuit which is currently in the process of installation.INTRODUCTIONSince 1936 when lead-zinc sulphide flotation commenced at Mount Isa, at least three types of ore have been encountered.Each ore has presented problems to flotation metallurgists.The three types of ore are,1. partially oxidized upper level sulphide ore,2. Black Star ore from the lower levels with its carbonaceous fraction, and3. Black Rock ore which is similar to 2, but more free milling.In retrospect a number of the metallurgical successes of the past were short lived. Often flowsheets or 0perating practices were designed to solve a single metallurgical problem associated with the current ore being treated. As the ore changed the problem would vanish and the method originally taken to counter the problem could become unnecessary or deleterious to the treatment of the new ore. The general lesson learnt from-the past-is-that thetreatment of Mount Isa lead-zinc ore involves a number of equally major problems...

Jan 1, 1963

The term slag has been used to define a wide variety of material including mine spoil and slag produced at steel plants. The present paper is concerned only with the non-metallic alumino-silicates developed simultaneously with iron in blast furnaces.The control of iron quality by slag has long been appreciated but here aspects of slag control based on concurrent iron production are indicated. Consideration is given to the basic composition of slags relative to the type of allotrope required. Up to a point, the plant conditions, under which a particular slag type is processed, have some effect, but these conditions only widen the range of a given allotrope.They do not convert one slag type into another. The nature of the slag types and experiments with additives to convert one slag type into another are discussed.The various uses for allotropes of blast furnace slag are considered.Their use in air cooled slag, foamed slag, slag wool, cements, soil stabilization, glass bottles, and building bricks and blocks, is explored in some detail.INTRODUCTIONWithin recent memory, blast furnace practice has been solely concerned with the production of iron. The slag make at this time had not reached embarrassing proportions. In Britain, unlike Germany, no legislation existed to prevent the growth of unsightly slag banks. Generally slag found limited use as fill and road material in the immediate plant vicinity. This is broadly the case in Australia today. In Europe and America, where the slag make is of the order of several million tons annually, the room problem and the cost of dumping slag has stimulated commercial and scientific research on the disposal problem. Currently, most iron plants in Europe can profitably dispose of at least 95 per cent of their slag make.

Jan 1, 1964

Flotation Circuit Optimisation - Towards More Sustainable Practice

Sep 13, 2010

By Johnson N. W

After an unsuccessful transfer from the laboratory to the pilot plant of galena flotation technology which used sodium metabisulphite and ethyl xanthate, laboratory flotation tests were conducted to identify any unusual variables which had a deleterious effect on the position of the lead rougher grade recovery curve for Hilton and Mount Isa silver-lead-zinc ores. Two variables (pulp temperature and contact time for ethyl xanthate and sodium metabisulphite) had important deleterious effects.The findings allowed a successful transfer of the laboratory process to a pilot plant scale process. The effect of temperature was important because the higher temperature (40°C) in the pilot plant pulp increased significantly the rate of reaction between ethyl xanthate and sodium metabisulphite. In the laboratory process at 20 to 25°C, the reaction rate was lower and did not interfere significantly with the process. The contact time for the two reagents was also important in the pilot plant scale process because of the higher reaction rate at 40°C.To employ ethyl xanthate in the pilot plant process, special precautions were required. Further, a collector (Aerofloat 241) from the dithiophosphate family was used successfully in the pilot plant process.

Jan 1, 1988

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of raining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENT The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939