Search Documents

By David J. Baxter

Use of bored displacement piles has experienced significant growth in the UK piling market sector, largely due to their environmental advantages over other piling methods and through cost benefits. Bored displacement piles are a cast-in-situ construction which can be formed with minimal production of spoil and offer low noise and vibration compared to driven displacement piles. A large variety of bored displacement piles have been developed. This paper describes a standard system for their classification. The development of the different types is described along with the factors which have led to their increased use. Consideration is given to processes undergone by the soil during pile installation and design approaches for bored displacement piles are compared. Comparisons are made between the different classifications of bored displacement pile. Comments are also made on the installation of such piles. It is concluded that complex changes occur in the stress states of the surrounding soils. Such effect of the pile installation on the soil should be accounted for and there is a need, therefore, to further refine the design process for these piles.

Jan 1, 2006

By F. O. Verret

Several grindability tests were developed over the years to design grinding circuits or optimize existing operations. Each test has its own strengths and weaknesses and it is imperative to select the proper test procedure(s) to meet project deliverables and minimize the risk of a project. Pilot plant testing of large bulk samples historically constituted the traditional approach for AG or SAG design, but was gradually replaced by small-scale tests. Nowadays, conducting grindability tests requiring only a few kilos of material on several samples is a more typical approach to grinding mill design. This paper summarises the requirements and deliverables of various bench-scale test procedures, their strengths and weaknesses, and cases where AG/SAG pilot testing should still be performed.

Jan 1, 2012

By K. K. Kelley

"INTRODUCTION The Bureau of Mines nitrogen peroxide process (2) 3/ for extracting manganese from low-grade ores is essentially a two-stage process involving the reversible reactionMnO2 + 2NO2 + 6H2O = Mn (NO3)2 . 6H2O (1).At lower temperatures this reaction proceeds to the rigth and affords a means of dissolving manganece and separating it from unreacted ore. At higher temperatures the reaction proceeds to the left and manganese dioxide is recovered and nitrogen peroxide regenerated for recycling. Evidently, therefore, the energy required for decomposition of manganous nitrate is a matter of practical importance. Similar information for certain other nitrates also is desirable beceuse the nitration step of the process produces appreciable amounts of nitrates of other metals, such as iron, aluminum, magnesium, calcium, and barium, some of which are not broken down in the evaporation and decomposition steps. Thus, a portion of the nitrogen peroxide is not directly available for recycling. Whether or not it is feasible to recover nitrogen peroxide locked in the more-stable nitrates depends partly on the energy required and the conditions necessary for their decomposition.To supply information bearing directly on these subjects, several researches were undertaken at the Pacific Experiment Station: (a) Heats of formation (24, 25, 26) of nitrates of manganese, magnesium, calcium, barium, and aluminum were measured at 298.2° K:; (b) low-temperature specific heats (23), in the range 51° to 298.2° K,, and entropies of nitrates of magnesium, calcium, barium, and aluminumm were determined; and (c) heat contents (21) above 298.2° K. of the nitrates of manganese, magnesium, calcium., and barium were measured. The results of these studies, when correlated by thermodymamic methods, permit evaluation, at any temperature of interest, of the energies required to decomposethe nitrates and furnish information concerning the equilibrium pressure temperature relationships."

Sep 1, 1944

By Richard E. Gertsch

Mechanical mining holds great promise for the mining industry. Realizing this promise depends on developing the tools needed to mechanize a mining operation with a reasonable expectation of success. Mechanical mining entered the 1990s with new machines, new operating methods and new ideas for the future. Mechanical mining can provide higher production, increase safety, reduce roof support requirements, create smoother openings for better ventilation, substitute continuous production for cyclical drill-and-blast procedures, and create opportunities for automatic and teleoperated control. The full promise of this important technology still lies ahead. Obstacles include: • Long-term production prediction: Mechanical systems have a high capital cost. Although recouped by lower operating costs, the tradeoffs are not always clear to mine operators. • Cutting tools for hard rock: Rock of more than 103.4 MPa (15,000 psi) cannot be cut by flexible mining machines. • Machine designs: Many machines cannot convert the required power into rock cutting capability. • Engineering: Better use of the machines in the mine is needed.

Jan 1, 1994

By Mike Boissonneault

It was three years ago when the “storm of the century” had taken a firm grip over the Pacific West Coast and inland areas. At the Big Sky ski resort in Montana on Christmas morning two ski patrollers set out to perform an explosives “hand charge” avalanche control mission that would see only one return. It has been difficult to determine exactly what happened. Investigators do know that there were three separate and consecutive attempts to light a safety fuse, when it had apparently been burning since the first attempt. Time ran out after the third attempt. Although this accident has had a profound impact on North American avalanche control programs, I am sure it pales in contrast to the shock and grief experienced by family members who lost a loved one.

Jan 1, 2001

The Wongawilli system of mining has been in use for over 30 years and has enabled high production rates and acceptable extraction ratios to be achieved in seams less than 4 m in thickness. A modification of the Wongawilli system has been developed to permit the use of a continuous miner and mobile equipment to extract a coal seam 6 m thick. Following physical and mathematical model studies the new mining method is now undergoing field trials at Collinsville, Queensland. Progress of the field trials to date has achieved 99 per cent extraction of the upper slice by remote control operation of the continuous miner and established the feasibility of installing resin grouted wooden dowels in the coal floor to reinforce the coal septum. The method is explained in the text. Monitoring of the goaf gases as an early indication of spontaneous combustion has been incorporated in the mining cycle by placement of tubes in the goaf as the face retreats and continuous analysis of the goaf gases made at the surface by the National Coal Board tube bundle monitoring system.

Jan 1, 1980

By P Fullagar

Automated multi-sensor core loggers (MSCL) measure petrophysical properties of diamond drill cores, including gamma density, P-wave velocity, electrical conductivity and magnetic susceptibility. A Geotek MSCL system has been used to record petrophysical data on archival drill core from Cadia East Au-Cu porphyry deposit, New South Wales, Australia, for correlation with metallurgical parameters. P-wave modulus, calculated from density and P-wave velocity, exhibits a correlation with small-scale crushability (A*b) test results, and hence offers a means for æcontinuousÆ characterisation of ore crushability at Cadia East. Magnetic susceptibility has proved to be a good indicator of alteration styles, and is a possible indicator of crushability.

Jan 1, 2009

By K. V. Raj, C. A. Berry, A. T. Weakley, A. L. Miller, P. R. Griffiths, D. A. Parks

Diesel particulate matter (DPM) has been classified as a carcinogen to humans by the International Agency for Research on Cancer. As a result of its potential carcinogenic nature, DPM exposure is regulated by the Mine Safety and Health Administration. Currently, diesel emissions in the workplace are monitored by collecting the aerosol onto filters, which are then sent to a laboratory for thermal-optical analysis using the NIOSH method 5040. This process can take days or even weeks, and workers can potentially be exposed to excessive levels of DPM before the problem is identified. Moreover, the delay involved in getting the loaded filter to the lab inevitably means the loss of some of the more volatile organic carbon. To remedy this delay, researchers from the National Institute for Occupational Safety and Health are seeking to develop a field-portable, real-time method for measuring elemental and organic carbons in DPM aerosols. In the current study, the use of mid-infrared spectrometry was investigated. It is believed that mid-infrared spectroscopy is more suitable for use in a real-time field-portable device than thermo-optical analysis methods. This article presents a method for measuring organic carbon (OC) and elemental carbon (EC) in DPM for a broad range of OC/EC ratios. The method has been successfully applied to laboratory-generated and mine samples.

By Fred W. Brackebusch

"The use of paste technology for surface tailings disposal may offer economic, technical, safety, and environmental advantages for both underground and surface mining operations. Paste is a non-Newtonian fluid having some shear strength during transport and placement. The strength is augmented after placement by consolidation, water loss, and by addition of chemicals. Economical dewatering systems are necessary to the success of surface paste tailings disposal. In an underground mine, the paste backfill plant can produce paste for surface disposal about 50% of the time because only about 1/2 of the tailings are needed for backfill. The distribution of paste to the surface stack involves expensive pumping equipment and thus a nearby location of the stack is desirable. The viscosity of paste can often be manipulated by modifying pH. Placement of the paste in a designed stack configuration depends on topographic and climatic factors as well as paste properties.INTRODUCTIONThe use of paste technology for mine backfill is becoming accepted for underground mines mainly because of ground control and economic reasons. Paste technology is just starting to be applied for tailings disposal with only a few hardrock metal mines worldwide using the technology; however, it has been used extensively for red mud disposal in the aluminum industry. The disposal of dry tailings is very attractive from environmental and safety points of view because of limited water which might potentially escape and pollute river systems. Dry stacking systems, however, are expensive because of filtration and truck transportation costs. Paste can be produced from most tailings streams by special types of thickeners. Furthermore, it can be transported in pipelines, therefore paste technology may be more economic than dry stacking but still have some of the major advantages. Understanding of paste technology has improved through experience with operating underground backfill systems in recent years and because of testwork and research programs by mining companies, consultants and equipment vendors. Thus we may be on the verge of taking a new look at tailings management using paste technology."

Jan 1, 2002

By Dapeng Zhang, Brij Moudgil, Shibo Zheng, Chunhui Feng, Wenyi Song, Wending Xiao, Patrick Zhang

Separation of dolomite from phosphate is the most challenging problem in phosphate mineral processing. Over 50% of the future phosphate reserve in Florida contains too much dolomite to process using the current industry practice. The current phosphoric acid production practice requires less than 1% MgO in the phosphate concentrate as the feed material. The Florida Industrial and Phosphate (FIPR) Institute has collaborated with worldwide experts in the field to address this issue. As a result, the industry is now offered three feasible options. Option 1 offers three methods for reducing MgO content in the concentrate from the Crago process, including adding a dolomite depressant in the rougher flotation step, dolomite flotation of the cleaner concentrate, and scrubbing the cleaner concentrate in quartz sand. These methods could reduce MgO content in the final concentrate by 20–40%. Option 2 involves crushing and grinding of high-dolomite phosphate pebbles followed by dolomite flotation at slightly acidic pH using a new collector that does not require phosphoric acid as a phosphate depressant, achieving a final concentrate analyzing less than 0.9% MgO at about 87% P2O5 recovery. Option 3 is a gravity separation technique using an innovative separation jig, and its full potential remains to be demonstrated.

By Craig T. Jones, Zachary Q. Maassen

"Jet grouting is a method of ground improvement that relies on the erosive capacity of high-speed jets to cut and mix the ground in place with a cementitious grout. A continuous return flow of cuttings, called jet grout backflow or spoils, is expelled to the surface during the grouting process. Data from projects completed in Toronto and Ottawa is presented where BOS Solutions’ services provided significant savings compared to the traditional spoils treatment utilizing vacuum trucks for spoils disposal. These traditional treatment methods are cumbersome and expensive by nature. BOS Solutions provided an alternative solution that is environmentally friendly and capable of handling full flow to process these jet grout spoils utilizing a tank system paired with centrifuges and flocculation additives to remove the ground soils and grout product from the spoils slurry. BOS’ process produced a clean water for reuse in the project while reducing the overall waste volume by producing a dry, stackable solid that could be hauled to a landfill. Benefits observed by using the BOS process were disposal waste volumes decreased over 30% and at least a 19% reduction on disposal costs.SCOPE OF WORKJet grouting is a method of ground improvement that relies on the erosive capacity of high-speed jets to cut and mix the ground in place with a cementitious grout. A continuous return flow of cuttings, called jet grout backflow or spoils, is expelled to the surface during the grouting process. The backflow, or spoils, is a mixture of grout, water and soils. Traditionally, the spoil would be collected in in-ground pits and allowed to solidify for a few days prior to hauling to a final disposal site. For the projects completed in Toronto and Ottawa, the jet grouting work was performed at street level, in high traffic congested areas, presenting the challenge of insufficient space for the contractors to process the jet grout spoils in the traditional way. At first, attempts were made of using vacuum trucks to collect and haul the wet spoils to an off-site location where the spoils would be allowed to solidify. However, this method proved cumbersome and expensive due to the high volumes of spoils generated daily and the high number of vacuum trucks required to support the jet grouting operations, respectively."

Jan 1, 2017

By Jack Eloranta

This paper documents the relationship between material handling and processing coete compared to blasting cost. The old adage, "The cheapest crushing is done in the pit", appears accurate in this c!ase study. Comparison of the accumulated cost of: powder, selected wear materials and electricity; indicate a strong. inverse correlation with powder factor (lbe powder/long ton of rock). In this case, the increased powder cost is more than offset by electrical savings alone.

Jan 1, 1995

By S. C. Sharma, M. Krishna, N. Sanmukha

"The oxidation behavior of an aluminium composite with 0, 2, 4, and 6% by weight of hematite at 200 to 500 °C has been investigated. Within the experimental temperature ranges a parabolic weight gain was observed. The, weight gain as a function of oxidation time becomes linear after an initial period on oxidation formation, an oxide scale was found whose morphology depends on temperature, cooling rate and sub-scale formation at the interface between the matrix and reinforcement. The presence of hematite particulate reinforcement has very little effect on the oxidation behavior. The interface oxidization rate was found to be higher than that of other regions. The, oxidation products were either metallic oxides or ceramic oxides. The exposure time of specimens to oxidation was 1000 minutes at various temperatures. In the present work key principles of alloy oxidation were discussed. Also the paper emphasizes various reactions taking ' place and the activation energies involved in the oxidation reactions.IntroductionMetal matrix composites (MMCs) reinforced with ceramic particulate, whiskers, or fibers have received increasing attention due to their potentially high fracture toughness and strength 1-5. Particle reinforced Aluminium MMCs find potential application in several thermal environment, especially in the automobile engine parts, space applications, such as drive shafts, cylinders, pistons, and brake rotors6.With the exception of gold, no metal or alloy is stable at room temperature, they tend to form their respective oxides. Most of the metals in the solid or liquid state are morphologically unstable when exposed to air at higher temperatures. An investigation relating to the temperature profiles of the piston area in a diesel engine has shown that the temperature can reach as high as 500¬800 K in certain regions of the piston. As the piston and cylinder areas are exposed to high temperature environment, the MMCs should have sufficient stability on both mechanical and chemical strength (oxidation). Oxidation occurs at grain boundaries in alloys and at the interface of the particulate and matrix in MMCs, which usually enhances intergranular fracture, resulting in premature failure and severe brittleness 8-10. Therefore for high-temperature applications, it is essential to have a thorough understanding of the oxidation behavior of aluminium MMCs."

Jan 1, 2000

By S. Prasad

The effectiveness of ultrasonic velocity measurements and attenuation of the propagating pulse was evaluated as a means of Non-Destructive characterization of cold worked and annealed copper. Commercial copper is subjected to mechanical working such as forging, rolling and thermal treatment to induce re-crystallization. The microstructural changes that occur in copper and a variation in its mechanical properties are subjected to analysis using the ultrasonic technique. The signal processing is carried out using the wavelet analysis technique. The features of wavelet analysis namely, localization in space and the presence of an infinite set of basis functions allows removing noise from the time series and components of a non-stationary signal to be analyzed. This is seen to improve the accuracy of the results obtained from the ultrasonic technique in the case of copper, which has distinct coarse grains that are difficult to inspect due to backscattering from the grain boundaries.

Jan 1, 2010

By Dany Pelletier, Yeves Breau, Ahmed Bouajila, Claude Gagnon

"In flotation circuits, direct measurement of the volumetric flow rate delivered by electromagnetic flowmeters is often difficult to obtain particularly due to piping and flow constraints. However, on-line material balance calculation could offer a reliable alternative to flow rate sensing. This paper describes an on-line material balance software package as applied to a copper flotation circuit for mass flow rate estimation mainly based on the output of an x-ray fluorescence onstream analyser. Rule-based procedures for the management of the main calculation modules are designed and integrated to a Comdale expert system. Attempts to diagnose the flotation process from mass flow rate data are also discussed.INTRODUCTIONThe need for improved process diagnosis, control and optimisation has become more evident for the mineral processing industry in the last decade. Therefore, new process variables need to be inferred or measured particularly in highly multivariable processes such as flotation. This process is subject to a wide variety of disturbances mainly generated by frequent and sometimes abrupt changes in physical and chemical characteristics of the ore and due to some irregularities in manual process operating procedures.A flotation circuit scheme is always a complex network counting more than two dozens of slurry streams. Information about those streams (%solids, metal content analysis, and flow rates) are important for process diagnosis, performance evaluation control and optimization (1,3).On-line sensing instruments such as x-ray fluorescence (XRF) on-stream analysers (OSA), gamma density gauges and electromagnetic flowmeters have been developed for the measurement of those variables. Unlike the other variables, stream flow rates could be determined by different ways:"

Jan 1, 2000

By L. Yuan, A. C. Smith

To provide insights for the optimization of ventilation systems for U.S. underground coal mines facing both methane control and spontaneous combustion issues, a computational fluid dynamics (CFD) study was conducted to model the potential for spontaneous heating in longwall gob areas. A two longwall panel district using a bleeder ventilation system with a stationary longwall face was simulated. The permeability and porosity profiles for the longwall gob were generated from a geotechnical model and were used as inputs for the CFD modeling. In this study, the effect of methane emissions from the mined coal seam, including the longwall face and overlying rider seam reservoirs on the gob gas distribution was considered. The spontaneous heating is modeled as the low-temperature oxidation of coal in the gob using kinetic data obtained from previous laboratory-scale spontaneous-combustion studies. Unsteady state simulations were conducted, and the effects of the coal’s apparent activation energy and reaction surface area on the spontaneous heating process were also examined.1

By Patrice Favreau, R. F. Ph. D. Professor Emeritus Favreau

After Nobel invented dynamite, blasts were carried out by trial and error, without the use of equations based on the fundamental principles of Chemistry and Physics, although everyone accepted that shock waves were involved; but no equations were available to calculate their intensity. Around 1950 however, M.A. Cook proposed a procedure to calculate the thermochemistry of an explosive, and thus evaluate theenergy released during the explosion of a fully confined explosive. Some blasters then began to use theEnergy Factor; the latter, however, does not subdivide the energy into its three kinds of activities necessaryfor a successful blast, as demonstrated in 1968 by reference 2, namely i) the shock wave which weakensthe rock; ii) the stress field SS which fully fragments the rock; and iii) the release of the stress SS whichcauses the fully fragmented rock to burst out with the velocity necessary to move the rock into the muckpile. The article explains that the way to achieve a successful blast is by insuring that the explosive energy divides properly into the weakening action of the shock wave which is necessary to prevent large collar blocks and toe, and into adequate stress field intensity SS which is necessary to obtain good fragmentation size distribution at the crusher, as well as adequate burst out rock movement to achieve easy mucking.

By Rameshwar Sah, Bharath Kumar Shanmugam, Govinda Raj Mandela, Marutiram Kaza, Harsha Vardhan, Harish Hanumanthappa

Iron ores obtained from different sources differ in their chemical and physical properties. These variations make the process of grinding a difficult task. The work carried out in this context focuses on three different samples of iron ore, viz., high silica high alumina, low silica high alumina, and low silica low alumina. The grinding process for all the three iron ores is carried out individually in Bond’s ball mill and the total retention time taken by each iron ore sample is calculated. The present investigation focuses on utilizing the calculated retention time of the iron ore as a standard grinding reference time to the laboratory ball mill for optimizing the grinding time of each ore. The desired P80 (150 μm) with an acceptable range of hematite liberation (> 75%) was obtained in the laboratory ball mill after reducing 6 min from the total retention time taken in the Bond ball mill.

By M. Visser

Keywords: Pyrometallurgy, furnace, ferrochrome, Samancor, ferrochrome process Samancor Chrome has been, and continues to be, a major player in ferrochromium production. The company has a proud history and possesses benchmark technology and operations. Currently five business units are operating: two sets of mines and three smelter plants. Samancor Chrome produces around one million tons of charge chrome annually. Chrome ore, intermediate-carbon ferrochrome, and low-carbon ferrochrome, form part of the portfolio. Electrode paste is also manufactured through a joint venture with Highveld Steel and Vanadium. Samancor Chrome has a balanced approach towards operational strategy, and has entered into a number of joint venture partnerships. Through its access to quality raw materials, knowledge, and experience of various production technologies, and its strategic abilities, Samancor Chrome is well positioned to reap the benefits from opportunities in the current and future industry context.

Jan 1, 2006

By Anthony Iannacchione

Coal mine bursts have represented a major hazard for U.S. mining operations for more than 90 years. During this time, many prevention controls have been developed and tested. This paper reviews 11 prevention control techniques. Although coal mine bursts are not common events in most underground coal mines, their occurrence almost always requires a change in mining practice. Over the many years of dealing with these hazards, specialized requirements for layouts and novel extraction sequences have been developed on a site specific basis. The keys to mitigating risks are to properly assess the coal burst hazards and to possess the knowledge and skills to prevent or remediate their occurrence.

Jan 1, 2008