Search Documents

By R. E. Mitchell

Environmental Impact Assessment (EIA) is the accepted method for evaluating proposed mining and other industrial projects to obtain regulatory approval and to help companies plan for responsible development. Another evaluation system becoming increasingly more common for proposed projects is the Environmental, Social and Health Impact Assessment (ESHIA). An ESHIA differs from an EIA for its more comprehensive and inclusive approach to evaluate potential impacts on public health, and its ecosystem services approach to assessing biodiversity impacts. An ESHIA may also be required by certain lenders for financing major projects. Conducting an ESHIA for a proposed mining development is not without its challenges, with costs, scheduling, regulatory concordance and other constraints to be considered. This paper examines some benefits and challenges of ESHIAs and summarizes lessons learned using a case study approach.

Jan 1, 2012

By John E. Urosek, Dennis A. Beiter, William J. Francart

In This Chapter [Designing bleeder systems Examining and maintaining bleeder systems Evaluating bleeder system effectiveness] INTRODUCTION Bleeder systems are that part of the mine ventilation network used to ventilate pillared areas in underground coal mines. Pillared areas are those in which pillars have been wholly or partially removed, including the areas where coal has been extracted by longwall mining. Bleeder systems protect miners from the hazards associated with methane and other gases, dusts and fumes, and oxygen deficiency that may occur in these mined-out areas. Effective bleeder systems control the air passing through the area and continuously dilute and move any methane-air mixtures and other gases, dusts, and fumes from the worked-out area away from active workings and into a return air course or to the surface of the mine. A bleeder system includes the pillared area (including the internal airflow paths), bleeder entries, bleeder connections, and all associated ventilation control devices that control the air passing through the pillared area. Bleeder entries are special air courses designed and maintained as part of the mine ventilation system. [This chapter focuses on the design, examination, maintenance, and evaluation of bleeder systems in underground coal mines.] The history of coal mine explosions in the United States is a reminder of the importance of adequate ventilation. Some of those disasters were the result of inadequately ventilated pillared areas. The importance of developing bleeder systems to ventilate these pillared areas and evaluating the bleeder system’s effectiveness is reflected in present-day federal regulations. For more information on bleeder systems, see Tisdale [1996] and Urosek and Francart [2002].

Jan 6, 2006

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

By Bill M. Stewart

Since 1974, a large amount of data has been developed concerning the physical properties and stability characteristics of waste generated by the mining and preparation of bituminous coal. However, very little information has been developed on the properties and characteristics of anthracite waste. During this Bureau of Mines research project, coarse anthracite breaker refuse from five sites in eastern Pennsylvania was sampled and the physical properties, which indicate stability characteristics, were determined in the laboratory. Coarse anthracite breaker refuse is quite similar to coarse bituminous refuse in chemical and mineralogical composition. However, the physical properties of the anthracite waste materials tested are different from those of coarse bituminous refuse. For the coarse anthracite breaker refuse tested, the average maximum laboratory density is 113.2 lb/ft3, the average angle of internal friction (direct shear) and average cohesion are 30.2° and 2.6 psi, respectively, and the average permeability (four sites) is 1.24 x 10-2 cm/sec. Stability analyses were conducted on six theoretical anthracite waste embankments. These analyses show the effects on minimum safety factors of geometry, phreatic surface level, and physical properties.

Jan 1, 1983

By Donald E. Raab, Lee W. Saperstein

INTRODUCTION The Premise Not much time has to be spent in a tunneling project to realize the tremendous interdependence that exists among the various unit operations. The research that is to be described attempts to examine one set of these linked operations, namely, the effect of cutters on muck handling properties. All too often research focuses on too minute an aspect of a problem for the results to be of much immediate, practical use. The goal of this research is to avoid this specificity. Apologies are tendered if this goal is missed. It is known that the mode of flow of bulk solids under the influence of gravity -- emptying a bin or hopper -- is dependent on several basic parameters. The size of the particles and the distribution of sizes (consist) determine whether the solids will first flow out of a given aperture; the cohesion of the solids will determine if flow will continue after the bin is opened; and the angle of internal friction determines the size of the flow regime (1,2,3). It is well understood that the latter two parameters affect the behavior of bulk material on a conveyor belt. Cohesion of material to a belt is always an undesired problem. Heaping of material on a belt depends on the material's internal friction. It is also known that varying the particle size, and the packing density of the material can affect the material's angle of internal friction (4,5). The question was posed whether sufficient variation in a mechanical tunneling machine's (mole) cutting function could be arranged to affect materially the handling properties of the muck

Jan 1, 1974

By F. H. Edmunds

I N presenting this paper, the writer wishes to point out some of the difficulties and problems of geological work in that part of Saskatchewan in which outcrops are few. These problems are well known to all geologists who have made investigations in this region, but may not be so well known to those outside. A table of the strata as known in certain areas of Saskatchewan and the adjacent provinces is given, with a brief discussion of some of the formations and beds about which there is little knowledge due to their being deeply buried and not exposed in the region. Comment with regard to possible oil and gas structures is made and some features of the structures in the Battleford and Simpson districts are described. The writer wishes to make acknowledgment to members of the Geological Survey of Canada to whose work in Saskatchewan and the adjacent provinces reference is made, and to others who have made, or are making, valuable contributions to the stratigraphy of Saskatchewan. Mr. G. C. Webb has kindly furnished information regarding and materials taken from a well bored recently in the Paynton district. Special thanks are due to the Simpson Oil and Gas Company for permission to use much valuable information with regard to their wells and for the generous way in which the officials and staff co-operated with the writer. The opportunities the writer has had to visit many parts of the Province have been in connection with investigations for the Provincial Department of Natural Resources and through facilities provided by the Department of Soils of the University of Saskatchewan. To these Departments the writer accords his thanks. For the purposes of this discussion, Central Saskatchewan may be considered as that portion of the Province extending from Township 16, with Regina, Moose Jaw, and Swift Current situated on or near the southern boundary, to Township 48, with Prince Albert and Lloydminster on the northern boundary. This region includes territory underlain by Cretaceous sediments and excludes the southern portion of the Province, where Tertiary beds underlie the surface and are exposed to an extent sufficient to permit a measure of systematic mapping.

Jan 1, 1937

By J. Adkins

This document presents a description of the results of a project aimed at producing a broad description of current mining training programs and an evaluation of their effectiveness with respect to reducing mine injuries. Aggregate training and injury data were used to evaluate the overall training effort at 300 mines as well as specific efforts in twelve categories of training course objectives. From such evaluations, recommendations were derived with particular emphasis being placed on identifying program characteristics that tend to be associated with effective training. Recommendations were also formulated with reference to role changes in industry and government interaction with respect to training programs, new or additional training programs, changes in the types of course materials and training methodologies, and recommendations concerning new areas for investigation.

Jan 1, 1976

By Theresa Y. Schulz

It is interesting to study the noise standards that have been promulgated in the US over the last decade or so. These regulations are likely to have long-lasting impact. The Occupational Safety and Health Administration (OSHA) Hearing Conservation Amendment (March 1983) continues to have influence not only in the workplace but in the debate over new regulations. Both the Mine Safety and Health Administration (MSHA) and Federal Railroad Administration (FRA) regulatory preamble documents state the desire to be consistent with OSHA. An examination of Table 1, which compares the major components of the three regulations and the 1998 NIOSH “best practices” criteria, depicts the extent to which that intent is met. There has been some regulatory activity in the last decade which may give some hope for evolution and updating based on the wealth of science that has occurred during the last quarter of a century since the OSHA regulation was enacted. However there has also been some “back-sliding” toward more lenient standards. The MSHA noise standard made regulatory progress in September 2000 by emphasizing engineering and administrative controls, followed by personal protective equipment, in the hierarchy of noise intervention. MSHA’s requirement for technician certification (today only available from CAOHC) strengthened the training requirements for audiometric testing in hearing conservation programs and MSHA also added the requirement of dual hearing protection at 105 dB TWA. There were many subtle differences between OSHA and MSHA based on comments and a desire to clarify some of the vague aspects of the OSHA noise standard, and meet the needs of the regulated mining industry. One example pertains to the ceiling for exposures. OSHA says, “no exposures >115 dBA,” which is interpreted to mean no unprotected exposures above that level, giving credit for the assumed effectiveness of hearing conservation programs, hearing protection devices and administrative and engineering controls. MSHA specified that a “P” code1 violation be issued for any protected or unprotected exposures >115 dBA. The Federal Railroad Administration (FRA) noise standard for railroad operating employees, which went The Modern Evolution of Hearing Conservation Regulationsinto effect February 26, 2007, was expressly based on the OSHA standard but also uses MSHA for comparison. The preamble states that the FRA defers to OSHA as the “primary regulator of noise in the workplace,” but also acknowledges the need for some departure from the OSHA regulation (FRA Preamble II.B). As an example, FRA requires testing at 8000 Hz “because it will allow employers to identify hearing loss sooner.” The FRA rejected MSHA’s hierarchy of noise controls in favor of requiring specific engineering interventions and focusing on appropriate hearing protection which would still allow communication and audibility, and identification of excessive noise through employee-filed “excessive noise reports.”2 Where OSHA has no specific mandate requiring employees to take advantage of the employer-paid audiogram, it has been traditionally a condition of employment and is generally accepted that OSHA-covered workers require an annual audiogram. MSHA addressed this issue in its preamble; however, they made no significant change. MSHA employers are required to offer annual audiograms but MSHA stopped short of requiring employees to comply with annual audiometric testing. The MSHA preamble does allow that mine operators can also make audiometric monitoring a condition of employment. FRA requires employees to

By Ramdane Bahar

"Abstract The design foundations can be performed using Menard pressuremeter rules that require a limit pressure and a pressuremeter modulus. In recent years, another trend of interpretation of this test is appeared. It consists of identifying the rheological soil parameters using analytical or numerical methods and then used to evaluate the bearing capacity and settlement of soil foundations using numerical software. This paper deals with the bearing capacity and settlement predictions of bored piles using two approaches. The first one is the method called ""Pressident"" which is a numerical program developed to analyse pressuremeter tests taking into account the Duncan and Chang model. The second approach is the method developed by Bahar and Olivari based on the generalised elastoplastic Prager’s model with the Von Mises criterion which is suitable to describe the behaviour of saturated clays under undrained conditions. The pressuremeter data, collected on various research and consulting projects are used to explore the relationship between limit pressure and undrained shear strength obtained by the two methods. Numerical calculations, by FLAC2D software taking into account the rheological parameters derived from these two methods, are performed in order to predict the behaviour of a single bored pile subjected to an axial vertical load. The predictions are comparedto the measured data.IntroductionThe Menard Pressuremeter test has been used extensively to measure in situ soil properties and for the design deep foundations in Algeria. These tests are an useful and economical way for obtaining reliable in situ properties of soils and provide the measurement of in situ stress-strain response of soils. From this test, the design foundations can be performed using pressuremeter rules that require a limit pressure, pl, and a pressuremeter modulus, EM. These two parameters are derived from the pressuremeter curve or deduced from existing correlations with undrained cohesion and internal angle friction (Ménard, 1957; Amar and Jézéquel, 1972), and are used to evaluate the bearing capacity of soil foundations and the expected settlements. But, they can also help to identify usual soil parameters required by simple constitutive models for soils in numerical calculations."

Jan 1, 2014

By S. F. Diehl

Weathered mine waste consists of oxidized primary minerals and chemically unstable secondary phases that can be sources of readily soluble metals and acid rock drainage. Elevated concentrations of metals such as Cd, Cu, Fe, Mn, Ni, Pb, and Zn are observed in deionized water-based leachate solutions derived from complex sedex and Cu-Pb-Zn mine wastes. Leachate (USGS FLT) from the Elizabeth mine, a massive sulfide deposit, has a pH of 3.4 and high concentrations of Al (16700 ug/L), Cu (440 ug/L), and Zn (8620 ug/L). Leachate from the sedex Faro mine has a pH of 3.5 and high concentrations of Al (2040 ug/L), Cu (1930 ug/L), Pb (2080 ug/L), and Zn (52900 ug/L). In contrast, higher-pH leachates produced from tailings of polymetallic vein deposits have order of magnitude lower metal concentrations. These data indicate that highly soluble secondary mineral phases exist at the surface of waste material where the samples were collected. Sulfide minerals from all sites exhibit differential degrees of weathering, from dissolution etched grain rims, to rinds of secondary minerals, to skeletal remnants. These microscale mineral-dissolution textures enhance weathering and metal leachability of waste material. Besides the formation of secondary minerals, sulfide grains from dried tailings samples may be coated by amorphous Fe-Al-Si minerals that also adsorb metals such as Cu, Ni, and Zn.

Jan 1, 2011

By W. W. Adams, T. D. Lawrence

"A. larger enrollment and a greater number of man-hours of employment by the enrolled companies were the outstanding features of the National Safety Competition of 1942, an annual safety contest conducted by the Bureau of Mines, United States Department of the Interior, for the promotion of safety among workers in the mines and quarries of the United States. The accident-frequency and accident-severity rates were somewhat higher than in 1941, but the frequency of accidents in relation to the number of man-hours worked was strikingly lower than in the earlier years of the 18-year period during which the contests have been conducted.Companies that enroll in the National Safety Competition compete for a bronze trophy known as the ""Sentinels of Safety."" Six of these trophies are provided by THE EXPLOSIVES ENGINEER annually for award by the Bureau of Mines. The trophies for 1942 wore won by an anthracite mine in Pennsylvania, a lignite mine in North Dakota, an underground metal mine in Tennessee, a limestone mine in Ohio, an open-cut metal mine in Minnesota, and a lime-:tone quarry in Pennsylvania. The trophies are presented to the companies for 1 year and are then transferred to the winners of the succeeding year's contest.The contest rules state that a mine or quarry must have at least 25 men employed underground or in the pit for at least 100 days, and the plant must be in operation 30,000 or more man-hours to be eligible for a trophy. The rank of mines and quarries is determined by accident-severity rates, or, in the case of accident-free records, by the number of man-hours worked."

Oct 1, 1943

By J. A. Bakken, M. T. Jonsson, G. A. Saevarsdottir, H. Palsson

The electrodes of a Submerged Arc Furnaces carry a high current and are subject to enormous stresses caused by both the electric arc itself, and the current distribution within the electrode. The external effect of the arc on the electrode is treated in a different paper at this conference, The purpose of this paper is to analyze the thermal effects of ohmic heating within the electrode at the arc attachment on the carbon based electrode, using data for Søderberg electrodes. The thermal conditions are then used to examine stress conditions in the vicinity of an arc. Two types of models of an electrode are presented in the paper. The first type is an accurate finite element model, based on both two and three dimensional elements and the second type is an one dimensional model, providing better insight into the problem. For the second type, a spherical model of thermal conditions in a semi-infinite solid has been developed. Results show that the electrode surface is heated quickly up to a maximum temperature and for a specific test case, the surface can only withstand the load for about 10 seconds. Also, the thermal stresses on the surface are very high which will increase erosion on the surface in addition to normal evaporation.

Jan 1, 2007

By Raymond P. Miller, David L. Monson, Robert A. Robinson

A geotechnical instrumentation program consisting of borehole extensometers and portable tape extensometer stations was effectively used to monitor concrete liner deformations and guide construction procedures during enlargement of a 75-year old Union Pacific Railroad tunnel in Wyoming. Enlargement involved excavation of the old concrete invert and placement of 5,941 feet of new concrete invert 6 feet lower in squeezing shales, fault zones and water-bearing sandstones. Instrumentation data were used to guide procedures for excavating the old invert, installation of temporary interior struts, underpinning existing liner walls, and placing the new concrete invert.

Jan 1, 1976

By F Gervilla, J Laukkanen

The Kevitsa Ni-Cu-PGE deposit in northern Finland contains disseminated Ni-Cu-Fe sulfides, and platinum-group minerals (PGM). The 2.05 Ga-old ultramafic-mafic, funnel-shaped intrusion is intruded into a volcanosedimentary sequence. The major ore minerals are pentlandite, hexagonal pyrrhotite and troilite, chalcopyrite, cubanite and magnetite. Pyrrhotite and pentlandite are replaced by pyrite, millerite and heazelwoodite near the surface. Nickeline, maucherite and gersdorffite are locally abundant. A pilot feed sample of 575 t of the main orebody at Kevitsa had average grades 0.45 per cent Cu, 0.36 per cent Ni, 1.85 per cent S, 0.33 g/t Pt, 0.34 g/t Pd and 0.19 g/t Au, with 0.06 per cent Ni contained in silicates. Higher PGE contents (2 - 27 ppm) occur in a vertical N-S bearing fault zone. The PGM (n = 6022) mapped in specimens of four drill holes, consist of sperrylite 34.7 vol per cent, braggite and cooperite 18.5 vol per cent, geversite 17.2 vol per cent, moncheite 14.7 vol per cent, merenskyite 6.7 vol per cent, stibiopalladinite 4.3 vol per cent, sobolevskite 1.9 vol per cent, kotulskite 0.7 vol per cent, michenerite 0.6 vol per cent, keithconnite 0.3 vol per cent, rustenburgite 0.1 vol per cent, melonite, froodite, laurite together 0.1 vol per cent and only a few grains of sudburyite, irarsite, vysotskite, erlichmanite, hongishiite, Pt-Cu-alloys, three undefined Pd and Pt bismuthinides and antimonides and a Pd-Cu-bearing Pt-Ni-Fe sulfide. Most of the PGM, 62 per cent, are enclosed in silicates, 29 per cent are intergrown with sulfides, nine per cent are within sulfides. A portion of the PGE occurs in solid solution in sulfides and arsenides. Ni flotation yielded smelter-grade concentrates averaging 12.2 per cent nickel. The average sulfide Ni recovery is 78.8 per cent and total Ni recovery is 65.3 per cent. The average Pt is 10 g/t at 55 per cent recovery, Pd 7.7 g/t at 38 per cent recovery and Au 1.6 g/t at ten per cent recovery. Cu concentrates averaged 28.6 per cent Cu with an average recovery of 78 per cent and further 11 per cent in the nickel concentrate. The copper concentrate contains 4 g/t Au at 24 per cent recovery. The average Fe to MgO ratio 17.9 is well above the targeted minimum of 4.5. The pilot results show that the previously used TETA (triethylene tetramine) can be avoided and good quality, smelter-grade concentrates can be produced from the Kevitsa ore at economical levels of recovery by conventional flotation methods.

Jan 1, 2008

By Paul Voigt, Mike Hourn, Glenn Stieper

Sable Zinc Kabwe Limited ("Sable") is a base metal processing plant, two kilometres south of Kabwe Town in Central Province, Zambia. The region has a rich history in mining and minerals production, being a major lead and zinc producer from the 1900s up to the mid-1990s. In 2006, a copper plant was built at the Sable processing site to treat third-party copper and cobalt oxide ores and concentrates. The oxide leaching plant included whole ore leaching, solvent extraction and production of 8,000 tpa LME Grade A copper cathode. The plant was placed on care and maintenance in 2014, and Glencore Plc ("Glencore") took the opportunity to convert the plant using a minimal budget, to an Albion Process™ plant to treat local refractory copper concentrates unsuitable or uneconomic for smelting. The Albion Process™ plant comprises an M100 IsaMill™ operating in acidic conditions such that raffinate from the downstream process is recycled back to slurry the concentrate delivered to site thus maximising copper tenor in solution and reducing water consumption. The finely ground concentrate feeds an oxidative leaching plant using the existing stainless steel oxide leach reactors converted to Albion Process™ duty by fitting HyperSparge™ supersonic oxygen injectors and gas dispersing agitators. The leached slurry is then directed to the existing solid/liquid separation equipment, and the PLS is then sent to the existing SX/EW plant. The plant also allows for cobalt recovery from the raffinate. The plant was designed based on testwork on regional copper concentrates. The plant was designed to toll treat a range of concentrates, and so the design was flexible With the flexibility of the Albion Process™ being one of its distinct advantages, the plant was ideally suited for tolling regional concentrates. The plant was commissioned and ramped up in six weeks using low-grade Zambian copper concentrate, and produced exclusively LME Grade A copper with over 99% leach recovery in the Albion circuit. INTRODUCTION The Sable Zinc Kabwe Limited ("Sable") process plant is located 2 km south of Kabwe town and 140km north of Lusaka in Central Province, Zambia. In 1902, rich deposits of zinc and lead were discovered with mines and processing plants operating in and around the town until mid-1994. In 2000, the Kabwe Mine tailings dams were sold to Sable, a newly established company, as part of a purchase deal for other plots and facilities. Up until 2004, Sable produced zinc cathodes in an SX/EW plant treating wash plant tailing material. In 2004, Sable was acquired by the South African mining company Metorex Limited ("Metorex"), and in 2006 a copper/cobalt SX/EW plant was built to produce copper cathode from malachite ore supplied from the Democratic Republic of Congo. In 2011, Jinchuan Group International Resources Co. Ltd acquired Metorex and Sable was in turn sold to a subsidiary of Glencore Plc ("Glencore").

Jan 1, 2019

Mineral Resource Throughput Management is based on the extraction of the maximum potential value from an ore reserve with the emphasis to generate maximum ROI and ROR (return on reserve). A steel producing company in India implemented MRTM to significantly improve their ROI and ROR. The value chain of this company consists of their own iron ore and coal mines, ore washing plants, sinter plants, steel plants, and sales and marketing division. The target for the mines was to produce at a stable and predictable rate and at specific quality requirements. These requirements were set to improve productivity and ROI of the steel plant. The implementation constituted the alignment of the reserve potential, total production chain, human resources and management culture at the mines with the requirements of the steel plant. Many typical mining practices were challenged and changed. Production targets regarding lump vs. fines ratio, consistent product tons, quality targets such as Fe, Al content and moist, and standard deviation on the quality targets were not achieved. A reverse distribution model with release mechanisms to satisfy the demand were developed and implemented at the mines. A stable and predictable flow of mine product with quality standards well within the required standard deviation targets were achieved. The contribution from the mines to significantly improve the Net Profit, ROI and ROR of the company were reached.

Jan 1, 2007

By A. Pratt

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

May 1, 2010

By Walford S. Wright, NORMAN EBBLEY

During the past decade (1937 to 1947), including the war years of heavy demand for metals, the United States realized about one-eighth of its antimony requirements from domestic production, chiefly in Alaska. In World War II, our foreign supply sources became endangered; and uncertainty in our Far Eastern supply made this nation focus on Alaska’s mineral resources with a Production Gear that centered in the Bureau of Mines experimental station at College (Alaska). The development work known as District or central deposits. The strategic mining districts included that of central Alaska was reorganized at Ketchikan Mining Districts. Mines were located here had produced considerable quantities since 1901; but methods for exploration had come from 1936 to spring 1942, some $4 million produced in gold alone. Statistics relating to available ores are those selected by type and exploitation periods with wide variety applied. During the summer of 1941, as part of an extensive Geological Survey program continuing through funds provided by U.S., geological surveys spent six weeks mapping an area approximately two square miles surrounding mines. The mines working both surface & underground work employed these men in mapping exercises.

Jan 1, 1948

By D. E. Calisaya, É. Poulin, A. Desbiens, R. del Villar, A. Riquelme

"A 15 cm diameter by 732 cm height, fully automated pilot column was installed in the Agnico-Eagle’s Laronde concentrator (Québec), for evaluating the performance of newly developed sensors and advanced process control algorithms. For eventual comparison purposes, the pilot column is continuously fed with the same slurry feeding the copper-circuit third cleaner column. It is equipped with electrical conductivity-based sensors for estimating the three variables used in the multi-variable control algorithm under evaluation: froth depth, fraction of wash water underneath the interface and gas hold-up. Froth depth is regulated using a PI controller while a predictive controller is formulated as the minimization of the tracking errors of gas hold-up and bias rate, keeping several operating constraints between their practical upper and lower limits. In particular, an unreachable high set point of gas hold-up can be selected in order to maximize the bubble surface area available for particle collection, while maintaining bias rate above a minimum value required for froth cleaning. The proposed strategy may indirectly help optimizing flotation column operation by using these secondary variables, without the implementation of a real-time optimization layer.INTRODUCTION Flotation columns have already been used for more than 30 years, mainly in cleaning stages, as a result of their froth washing capabilities. Despite their widespread usage, the measurement of some pertaining variables and their use for automatic control is rather scarce. Among the most important variables directly related to the process metallurgy (concentrate grade and recovery), froth depth (hf) is the only one normally monitored and controlled. Even though commercial sensors are available, gas hold-up (eg), a variable directly related to concentrate recovery, is seldom measured and never controlled. Another important variable, bias rate (Jb) responsible for concentrate cleaning, is simply not measured at all, as there is no commercial sensor available. Therefore, besides froth depth, continuous monitoring of process variables is limited to flow rates (gas, feed, tailings, wash water), i.e. to manipulated variables. Some new available sensors have been industrially tested, e.g. the Sonar-TracTM for eg (O'Keefe, Viega & Fernald, 2007) and the McGill hold-up sensor (Tavera & Escudero, 2002). Others, for bias rate and frother concentration, have been successfully validated at laboratory scale by Laval’s LOOP researchers (Maldonado, Desbiens, del Villar & Chirinos, 2008b; Maldonado, Desbiens, del Villar & Aguilera, 2010a). Some devices have been extensively used for monitoring bubble size and space distri-bution, e.g. McGill bubble viewer (Gomez & Finch, 2007) and others."

Jan 1, 2012