Search Documents

By D. Harrington

For many years the Federal Bureau of Mines-in cooperation with other agencies-has been making investigations and compiling and publishing reports and statistics on accidents in the various branches of the mineral industry.4 Its assistance has been enlisted also in health, safety, and ventilation problems' incident to the driving of many large tunnels in the United States in recent years. As part of this work the Bureau has compiled considerable statistical and other information on accident experience in the tunneling branch of the heavy-construction industry. It has always been difficult to obtain up-to-date information on tunneling methods and tunnel accidents. Published accounts of tun¬nel construction furnish much interesting material of engineering, historical, or fiscal value, but usually little or no attempt is made to discuss and critically analyze the means taken to preserve the health and life of employees.

Jan 1, 1941

By Roy A. Imbsen

Following the 1989 Loma Prieta earthquake, California Department of Transportation (Caltrans) expedited an effort to evaluate and retrofit important state-owned toll bridges to en­hance performance of the state's transportation systems during and after major (credible) earthquake events. Imbsen and Associates, Inc. (IAI) along with their sub-consultants, were awarded a contract to conduct seismic evaluation and to develop retrofit design for Benicia-Martinez Toll structure, to meet a "Serviceable" performance requirement after the event of a "Safety Evaluation Earthquake." This paper describes the design and construction specifications for the deep foundations supporting the main spans of the Benicia-Martinez Bridge. Benicia-Martinez Toll Structure (George Miller Bridge), a high-level deck-type welded truss bridge with welded girder approach spans, carries Interstate Route I-680 over the easterly end of Carquinez Strait near San Francisco, CA. The nearly 5000 ft long main truss structure consists of ten spans, ranging from 330' to 528' in length, supported on cellular reinforced con­crete pier structures. Foundation systems across the waterway, consist of cellular reinforced concrete footings, supported by groups of 6' diameter, concrete filled, steel caissons, resting on 5' deep rock sockets, at depths of 50' to 150' below the water level. Seismic evaluation of the existing foundation systems accounted for spatially varying ground motion along the length of the structure, variability of foundation material strength (i.e. at bed-rock), variation and effects of scour depth on the performance of the foundations, and dy­namic soil-structure interaction. Performance of caissons beyond their elastic strength, as well as their effects on the behavior of the foundations and substructures were evaluated and considered in establishing foundation vulnerabilities. Several retrofit strategies were considered leading to a final retrofit strategy to strengthen end connections of existing caissons, as well addition of new caissons to provide adequate lateral force resistance for the foundations. Final design package includes specifications as well as construction methods and requirements for existing and new caissons, under traffic, and pile load testing procedures for design loads of up to 12500 kips per caisson.

Jan 1, 1998

By E. R. Wang

This paper outlines the engineering properties of shallow soil in Shanghai area. The main points that should be paid attention to during deep foundation investigation, and general conditions of experimental soil engineering are discribed.

Jan 1, 2010

By Charles H. Jacoby

The solution mining of evaporites has a history of approximately 5,000 years. The insitu leaching of metalliferous ore will have many of the same characteristic problems which have confronted industry for years in the production of evaporite minerals. Basically we will be converting the less soluble forms of valuable metals into their more soluble salts and producing these in much the same manner as, for example, sodium chloride. There are a number of problems which we are faced with that are more complex and complicated and, therefore, will require a higher degree of sophistication than previously employed. One of our most important undertakings will be the clearcut definition of the problems involved. While a great deal of expertise can be drawn from the solution mining of evaporites and the oil industry, problems peculiar to the hydrometallurgical field will need to be solved. One of these is the introduction of permeability into an impermeable rock so as to expose the sought after values of metals which by volume are infinitesimal when compared with sodium chloride, potash or other type water soluble mineralization. After establishing this permeability which will be miniscule when compared to a solution cavity, there will be the maintenance of this permeability. In general, salt deposits are of a somewhat uniform chemical composition and thus their chemistry was relatively simple. Each metalliferous ore body is somewhat unique in its chemistry and will need to be treated accordingly.

Jan 1, 1974

By D. R. Babich, E. R. Bauer

National Institute for Occupational Safety and Health (NIOSH) researchers are conducting a cross-sectional survey of equipment noise and worker noise exposures in the mining industry. Surface and underground limestone is one commodity recently surveyed. The sound levels of mining and processing equipment were recorded to identify noise sources. Full-shift worker noise exposures were completed to determine the exposure of various occupations. This paper presents the results of the noise research conducted in both underground and surface limestone mines, detailing the equipment likely to cause worker overexposures, and the occupations experiencing overexposures. Implications for worker noise exposure reduction are also reported.

Jan 1, 2006

By Hyung-woo Kim, Kiyoung Sung, Sup Hong, Jung-Yeul Jung

Many concepts for the commercial production of deep-seabed manganese nodules have been studied since the 1970s. However, the bearing capacity of the deep seabed is not strong because it is composed of fine particles with high moisture content. So it is impossible to carry manganese nodules in the collection system. Therefore, the validity of continuous mining by riser pipe from the seabed to the vessel is highly appreciated. A continuous mining system is composed of mining vessel, lifting pipe, buffer system, transport tube (flexible pipe), and self-propelled mining robot. A conceptual diagram of this system is shown in Fig. 1(a). Korea Research Institute of Ships and Ocean Engineering (KRISO) developed a deep-seabed self-propelled mining robot called "MineRo" to collect manganese nodules in 2012 (as shown in Fig. 1(b)). In 2013, real sea experiments at around 1380 m depth were carried out to evaluate the collecting and driving performance of MineRo. However, we found that the roller in MineRo did not work well at times. To elucidate the problem, we analyzed the rheological characteristics between the bushing and drive shaft under deep-water conditions.

Sep 1, 2014

By Marcel Vallée

Frequently, costs overruns and defaults in mining project performance result in serious problems and headaches for all project participants and impact on corporate objectives, profits and image and, occasionally, lead to project failure. As mining professional s, we should be very concerned that, in a recent World Bank paper (Weber-Fahr, 2001), geological and technical risks were considered the most important ones facing mining projects. Whenever we manage to reduce or minimize these risks, we are in better position to overcome the environment-, market-, finance- and community-related ones. The causes of this situation seem rather systemic, as a fairly long list of industry problems with new pro jects has been described in industry papers in pas t and recent years. A brief review of industry problems with mining projects will be given first, followed by a review of the basics of the current Quality Management and Continuous Improvement perspectives that have evolved from earlier quality control and quality assurance systems and policies. Particular particular attention will be given to the work of W. E. Deming. As the system approach is an essential part of such policies, it will be described succinctly. Given that poor communications and interactions among geologists, mineral processors and mining engineers/operators ca n seriously affect project efficiency and profitability, these interrelated processes with in the mining systems will be analyzed and modelled and the impacts of such situations will be described through a number of anonymous case histories and examples. A synthesis of Dr Deming's management system, includ ing his Four teen P oints and System of Profound Knowledge, will be prese nted .

May 1, 2002

By P. G. Killeen

Proper calibration of portable gammaray spectrometers and spectrometric logging equipment is essential if they are to be used for accurate quantitative determinations of radioelement concentrations. In the case of both types of equipment, it is necessary to determine the system calibration constants (stripping factors and sensitivities). In the case of borehole logging equipment, it is further necessary to determine the system response characteristics if the data are to be computer processed to improve the accuracy and resolution of the logs. Facilities are now available near Ottawa for the complete calibration of portable gamma-ray spectrometers and spectrometric logging equipment, in addition to already existing facilities for calibrating airborne gamma-ray spectrometers. Limited additional facilities are also available or planned in several other areas of Canada.

Jan 1, 1978

By W. E. Oching, M. M. Ghomshei

"Collaboration among Ventilation Engineers, Mine Inspectors, worker representatives, health and safety officers and management is key to an effective operational mine ventilation management. Mine ventilation training, ventilation survey reports for mine stakeholders and interaction with mine frontline workers and management concerning safety, energy saving, assets management and maintenance are effective tools in implementing best industry practices and significant reduction of ventilation operating costs without compromising safety. These approaches may not be new to well established mining companies but the real dilemma is how to implement them effectively and this is what this paper will address.INTRODUCTIONManaging an effective mine ventilation system is becoming increasingly challenging, especially during tough economic times in the mining industry. Management strives for more production while frontline miners work hard to surpass the production targets, thus improving their incentives and above all aiming to enhance the prospects of their job security when the mining industry is facing challenging times. Taking shortcuts by not fully following the safety regulations or industry best practices are often notable, resulting in the rise of Workers Compensation Board claims and temporary shutdowns of active workings, compromising productivity and increasing the operating costs.In accordance with the Mines regulations in various jurisdictions in Canada and the US, it is evident that companies adhere to establishing basic ventilation management systems through the provision of the code of practice, procedures, work practices and standards/guidelines. This is aimed at ensuring the health and safety of underground workers (de Souza, 2017). However, the challenge to many operations is the improper implementation of the mine ventilation regulations including some managers showing reckless disregard for workers safety by focusing on production and not worrying to address ventilation problems (Steven & O'Keefe, 2010). Other challenges facing effective ventilation management include inadequate training of frontline workers on ventilation system and hazards associated with poor ventilation systems such as toxic gases, dust, heat, and underground explosions (Mufson et al., 2010; Suvar et al., 2017); friction between mine managers and the mine inspectors (Mufson et al., 2010), improper maintenance of ventilation system and inventory management, among others."

Jan 1, 2019

By D. Imeson, T. Grammatikopoulos, G. Pearse, M. Aghamirian, C. Mohns

"Spodumene mineral is a source of lithium for lithium ion batteries. Thus, the production of a spodumene concentrate with an approximate grade of 6% Li2O is targeted. Traditionally, spodumene is concentrated by froth flotation using fatty acid as the collector. Amine collector can also be used to float mica ahead of spodumene as required or feldspar from the spodumene tailings. Slimes have a negative effect on spodumene flotation and they are commonly separated by scrubbing and de-sliming prior to spodumene flotation. The main losses in spodumene flotation typically occur in cyclone overflow, scrubbing slimes, spodumene flotation tailings and mica concentrate. In recent years, dense media separation (DMS) is the main concentrating process in Australian spodumene operations. In these operations, DMS is efficient at generating coarse grain concentrates and rejecting large portions of silicate gangue, thereby directly reducing the milling cost. The ore should be crushed to 3/8” or coarser while further crushing is possibly necessary on the middling particles to scalp further spodumene. The DMS feed should be classified to remove fines (typically -0.5 mm particles). The final middlings and undersize fractions could then be processed by flotation. The main requirement in DMS operations is to have good spodumene liberation at relatively large grain size. This paper reviews the most significant DMS and flotation parameters in spodumene beneficiation. The treatments of different minerals in the spodumene ore are also addressed.INTRODUCTION A number of laboratory/pilot plant programs have been recently conducted at the SGS Lakefield site, sponsored by different clients. The main objective has been to develop a process flowsheet to generate a spodumene concentrate containing 6.0% or higher Li2O (~75% spodumene) suitable for producing lithium carbonate by a hydrometallurgical process. Depending on spodumene liberation size, dense media separation (DMS) can be an attractive option to produce a final high grade concentrate and to reduce the mass to be treated in the flotation circuit. In such a case, crushing would typically be performed in stages, with DMS separation to recover a spodumene concentrate and reject gangue minerals following each stage. DMS middlings and -0.5 mm fines can be processed by flotation to further recover spodumene. In the flotation process, coarse stage grinding minimizes the grinding cost and formation of slimes. In the majority of cases, a grind size (K80) of approximately 200 microns is sufficient for flotation. After primary grinding, mica, if present in an appreciable amount, should be floated to minimize interference with spodumene flotation. Desliming after scrubbing and high density conditioning are the key process operations prior to spodumene flotation. Spodumene can then be floated from silicate gangue minerals with a fatty acid or a mixture of fatty acid and petroleum sulfonate at slightly alkaline pH. Subsequently, feldspars can then be floated from the spodumene tailings."

Jan 1, 2012

Remote sensing methods have been used to evaluate vegetative growth patterns for many applications, though relatively little work has focused on tracking mine reclamation progress. For coal mines in Central Appalachia, reclamation approaches that include production of biofuel feedstocks are increasingly attractive, as these may yield significant post-mining land values and contribute to carbon-neutral energy supplies. To optimize productivity, the influence of reclamation parameters must be well understood ? which necessitates tracking biomass production over long time periods. Satellite-based estimations may offer low-cost alternatives to conventional biomass appraisals, and also the potential to provide critical input for carbon accounting at varied spatial scales. In this paper, we use biomass production experimental plots on reclaimed mine sites established by the Powell River Project (PRP) for a comparative study between satellite measurements of Normalized Difference Vegetation Index and inventory estimates of biomass under a variety of conditions. The PRP is a unique public-private partnership in the coalfields of southwestern Virginia dedicated to enhancing beneficial use and environmental protection of mined lands.

Feb 27, 2013

By H. D. Outmans

A method has been developed for determining the relative water wet-tability (fraction of the surface wet by water) of porous media. This method involves the adsorption of methylene blue dye from an aqueous solution onto the solid surfaces of rock contacted by the injected dye solution. Experiments on Berea snndstone cores have shown that water-wet cores adsorb a large amount of dye from solution. In oil-wet cores, however, the injected aqueous dye solution is prevented from contacting the adsorptive surfuces by a film of oil and virtually no dye is adsorbed. This method was tested by experiments on mixtures of water-wet and oil-wet sand. Using the dye adsorption method, it was possible to determine quantitatively the fraction of water-wet and oil-wet sarzd in such mixtures. The dye adsorption test is readily applied to determinitrg the relative water wettability of fresh oilfield cores. The cores are not extracted before testing. Observed values of the wettability of field cores tested to date have varied from 100 to 6 per cent water wet. INTR OD UCTIO N Recent articles1 ' have emphasized the important role that wettability plays in almost all phases of reservoir rock behavior. It has been shown that wettability has a profound effect on the interstitial water saturation, residual oil saturation, capillary pressure, relative permeability, waterflood behavior, and resistivity index of oilfield cores. A quantitative investiga- tion of the effect of wettability on these core properties is severely handicapped by the lack of a simple technique for measuring the wettability of a porous medium. If such a technique were available, it would provide investigators with a means of gaining insight into the distribution of phases within a core. A number of qualitative methods of estimating wettability are known. These include contact angle measurements, flotation tests and studies of displacement pressure: imbibition7 and relative permeability data.' Using these tests, it is usually possible to classify a core as water-wet, oil-wet, or some intermediate degree of wettability. One recently proposed method involving measurement of nuclear magnetic relaxatione offers promise of determining quantitatively the fractional wettability of cores. The equipment is rather elaborate and necessary treatment of the cores before testing probably alters the natural wettability. This latter point also applies to most of the cited qualitative methods. This paper presents a new technique for determining water wettability of cores; it is based on measurements of the dye adsorption capacity of the core. This method has the advantage of requiring relatively simple equipment and involves minimum handling of the core before testing. It is important to distinguish between the various concepts of wettability referred to in the literature. The term "wetting" is defined by Bartell as that phenomenon which occurs when a solid and liquid phase come in contact in any manner so as to form a solid-liquid interface. A preferentially water-wet solid is defined by Jennings in terms of the advancing contact angle in the solid water-oil systems. Brown and Fatt regard fractional wettability as the fraction of the total surface area that is preferentially oil-wet or water-wet. However, none of these definitions adequately describes the type wettability measured by the dye test. This calls for the introduction of a new term, "relative water wettability", which we define as the fraction of the total surface area of a core contacted by injected water. DESCRIPTION OF METHOD The ability of a porous medium (especially the clays) to adsorb large quantities of surfactants, dyes, etc., is well known. It is reasonable to assume that a substance can be adsorbed from solution onto a solid surface only if the solution contacts the surface. In this connection Shapiro" has shown by experiments on silica gel that completely dry gel will adsorb methyl red dye from a benzene solution. On the other hand, if a film of water more than several molecules thick is present on the silica gel, the adsorption capacity of the gel for the dye is drastically reduced. Thus, a study of the dye adsorption capacity of cores should give some clue as to the fluid distribution on the surface of the core. TEST OF METHOD As a qualitative check on this theory, dye adsorption tests were run on similar Berea sandstone cores (Table 1, Cores 1-5). Cores saturated initially with water and flooded with 0.01 per cent aqueous methylene blue adsorbed 0.58 mg dye/gm of core. Similar cores saturated initially with water, driven to irreducible water with oil, and then flooded with the same dye solution also adsorbed 0.58 mg dye/gm of core. Another core, treated with a 5 per cent Dri-Film solution, dried and saturated with oil (Soltrol) adsorbed no dye when the dye solution was injected. These tests confirm

By Fred C. Schmednecht

For years, the strategy was to contain waste and in many applications, is still the recommended method. Recently, it has become acceptable to create filters below ground for the in-situ treatment of waste. Consequently, in lieu of the waste being contained, it is desirable that the waste flow through a pervious treatment zone. For instance, subterranean pervious walls comprised of iron sand are particularly useful in treating chlorinated solvents in contaminated groundwater. The iron acts as a corrective filter to treat the contaminated groundwater. How are these impervious and pervious walls being constructed? One effective means of constructing an impervious barrier is the vibrated beam method. This method, in brief, involves the use of a fabricated steel beam, a vibrator, a pile driving crane, and a mixing plant. This method results in a 4-6" wide wall with depths up to and exceeding 100'. Over one hundred slurry walls have been installed using this method in the United States. The need for the vibrated beam method continues to escalate due to its reduced health and safety considerations, high level of quality control, lack of excavation, narrow working area, and ability to achieve depths greater than 100'. A recent project was in Marinette, Wisconsin at the ANSUL facility. The project consisted of a 28,000 square foot slurry wall and was completed in January of 1999. Another effective means of creating an impervious barrier, where structural support from the barrier is needed, is the Waterloo® Barrier System. This system involves the use of a pile driving crane, Waterloo® steel sheet piles which are patented steel sheet piles due to their groutable interlocks, and a grout plant. This system results in a water-tight barrier due to the grouted interlocks and provides structural support. A project was completed at Beta Steel in Portage, IN for a retention pond to protect Lake Michigan. Due to the new concept of "filtering", there are few accepted construction techniques available. One effective field proven construction technique is the patent pending mandrel emplacement technique. This technique involves the use of a fabricated hollow steel mandrel with a shoe, a vibrator, a heavy duty crane, and a material feeder. This technique results in a pervious wall which may be comprised of pure iron sand or any other flowable media. Using this technique, the pervious wall may be constructed in varying widths to depths in excess of 100'. A successful installation occurred in October 1997 at Cape Canaveral Air Station in Florida.

Jan 1, 1999

By Roozbeh Afzali

Designing an appropriate tunnel blasting pattern reduces the cost of rock breakage and subsequent operations such as loading, haulage and support of tunnels. For that reason, we developed a software that designs tunnel blasting patterns. Using this software, three different tunnel blast design models based on parallel hole cut, namely, Swedish, Konya and Energy Balance, were investigated and compared for a virtual tunnel. Accordingly, blasting patterns were designed, for different cross sections. The trend of parameters such as specific charge and specific drilling as functions of tunnel cross-section was determined for each model. Our results show that, in general, The Swedish model gives lower specific charge and specific drilling compared to other models.

Jan 1, 2008

By Michael H. Wysockey

The load test program for the pile foundation at Soldier Field included static and dynamic load tests at four locations around the site. The dynamic tests were run with no knowledge of the static results, and comparison between the two is very good. It was necessary to use a special testing hammer (not the production hammer) to demonstrate capacity with dynamic testing. Over 90% of the piles were HP14x89 with a design load of 230 tons (18 ksi). The load tests showed a capacity in excess of 590 tons for all tests where sufficient set up time was allowed. The remainder of the piles were mostly HP 12x53 with a design load of 100 tons (13 ksi). The measured capacity of these piles was typically about 250 tons. One experimental HP12×74 pile with a nominal yield of 65 ksi held 730 tons (67 ksi) before failing.

Jan 1, 2002

By Peter Faust, Jeremy Zorne, Timothy Siegel, Diane Fiorelli

Professional sport venue construction follows a very simple rule. Once the decision has been made to move the team to a new place, construction shall begin immediately, so that not more than one or two seasons pass by stuck in the old home. Such tight construction schedules require a different approach than traditional design-bid-build contracts. Design is mostly done on the fly, the construction schedule becomes a main risk factor and an early contractor involvement is desired. As specialty contractors become more and more sophisticated, owners, their construction managers or the general contractor have realized the value of ideas and modern technology they can bring to the table for a successful and fast project completion. Local knowledge and experience in a variety of solutions play a key role in the specialty contractor’s ability to provide added value to the project. This is also true for the specialty foundation contractor, who needs to understand the complexity of such modern structures from its integrate foundation, over the delicate concrete structure to a potentially fancy movable stadium roof. Not to mention all the modern high tech equipment which shall make such a place a great customer experience. His expertise shall enable him to propose the most suitable foundation element for the given ground condition and application. Rather to build what others have designed, his strength is to propose alternate concepts which will be faster and (hopefully) more cost effective. This paper highlights different value engineering (VE) input a specialty foundation contractor had on 3 major sports arena projects in California. Together with the entire team from owner to GC, including the Geotechnical (GEOR) and the Structural Engineer of Record (SEOR), the most efficient and best performing foundation solution can be found every time. But such an approach also requires the open mind of the owner to entertain last minute changes when the permit drawing set has already been submitted for approval.

Jan 1, 2018

By Z. Jun, L. Kerning

Jinlong copper smelter and refinery, originally designed for 100,000tpa primary copper and started up in 1997, has been expanding its capacity on the basis of operational optimization and by modifying its facilities. Currently it is producing 210,000tpa primary copper, and the new phase of expansion project with a target capacity of 350,000tpa primary copper is ongoing. This paper reviews problems and improvements made with operation and equipment in the past years. Recent plant operation is briefly described. The expansion projects completed are summarized and the ongoing expansion project is present.

Jan 1, 2007

By Jr. Sayre

Results of studies of reservoir and wax-precipitation temperatures relating to wax deposition in the reservoir of the Bradford oil field are presented in this report. During 1949 and 1950 Bureau of Mines engineers made temperature measurements in 42 wells, which indicate that the Bradford Third-sand temperatures range from 59.7° F., at 1,150 feet, to 71.9° F., at 2,040 feet. Reservoir temperatures measured at the same depths in newly drilled wells and oil-producing wells differed as much as 4.5u F. Injection-well temperatures measured during water injection showed that the temperature of the water entering the sand was 11.5° F. lower than reservoir temperatures before injection. The cooling in the formation resulting froth the injection of low-temperature water was 11.5° F. in the vicinity of the injection-well bore, and a maximum of 2.1° F. 200 feet from the injection well. Sand temperature, after 5 months of water injection, was reduced 1.5° F. 90 feet from water-injection wells. The temperature at which wax begins to precipitate from solution in crude oil was determined at atmospheric pressure for 26 samples and ranged from 51° to 67° F. Oil samples from wells producing no water had wax-precipitation temperatures ranging from 51° to 58° F. and wax contents from 2.20 to 2.97 weight percent, whereas the samples from wells producing water and oil had wax precipitation temperatures ranging from 580 to 67° F. and wax contents from 2.57 to 3.42 weight percent .

Jan 1, 1952

The Functional Performance Equation for ball milling circuits allows us to isolate the circuit classification system efficiency (CSE) from the mill?s grinding performance. The factors which affect circuit CSE are reviewed, with emphasis on water usage at the classifiers. It is shown that manipulation of such water usage can be carried out to improve plant grinding circuit efficiency, at times by more than 30 percent.

Jan 1, 2009

By X. M. Zhou, T. Wu, He X. N.

"In order to study the support effect of concrete in the surrounding rock of a metal mine, the concrete and surrounding rock were comparatively studied. Firstly, the general situation of the ultra-kilometer deep shaft in Xincheng, surrounding rock and geological conditions are introduced. Secondly, the experimental scheme of material mechanical properties of surrounding rock and shaft lining concrete based on same standard dimension and shape are examined, and the mechanical tests of rock and concrete based on different shapes and sizes are carried out. The study shows that the compressive strength value and elastic modulus of the rock cube are 1.28 times and 1.78 times that of the cylinder, and the Poisson's ratio is 0.77 times. The dimensional effect law of the concrete cube and cylinder test data is consistent with the rock law. However, the test results of the concrete are less discrete than the rock; the test also shows that the strength and elastic modulus of the concrete lining of the main shaft of the Xincheng are much smaller than the surrounding rock that is also used as the concrete aggregate, which indicates that the support of concrete lining in the surrounding rock shaft behaved weakly. Based on the development of the modern NATM rock support theory, it is suggested that the mechanical test standard of artificial support materials should be unified into the mechanics test standard of natural rock, which will help to improve the accuracy and practicality of scientific calculation of geotechnical engineering.INTRODUCTIONConcrete and rock mass are usually attributed to a class of materials called frictional materials or geotechnical materials, of these two kinds of materials, the first is man-maded and the second is natural. The attentive scholar can find that there are many differences in the test criteria for the mechanical properties of the two kinds of materials among different industries or departments, reflecting the differences in their sources, tradition, and the application thoery of material strength among them.There is a situation wordwide, that there are many testing standards of the same material mechanical parameters such as elastic modulus, compressive strength, etc. The cube with a side length of 150 mm is adopted as a common sample in the architecture department in China, while a cylinder with a diameter of 50 mm and a height of 100 mm is as a standard specimen in geotechnical department.Knowing that mechanical parameter values are strongly affected by the the size, shape of specimen and loading rate etc, that is to say the mechanical parameter values of the same material are completely different when obtained from different test with different standards. However, such a problem has been long neglected in geotechnical engineering."

Jan 1, 2019