Search Documents

By Verya Nasri, Heather M. Ivory, Kevin Clarke, Eric Cole

Development of the New York City Water Supply System The New York City water supply system serves a population of almost nine million, including residents in neighboring counties. Peak day demands on the system are currently running at about 70 m3/sec (about 1,600 mgd), which is significantly lower than in the 1990s. This trend of reducing demands over the past 25 years, which has been experienced in other major urban centers in the US, is mainly the result of conservation measures and increased cost consciousness on the part of water users. In the long term, demands are expected to once again follow an increasing trend with population growth, so that by the end of the planning horizon of these studies, the year2045, the peak day demand is expected to increase to about 85 m3/sec (2,000 mgd).The system is served largely by surface water sources, regulated by a system of 19reservoirs and three controlled lakes, which are connected to the City by a series of aqueducts, the longest of which is about 87 km (54 miles). The total storage in the sys-tem amounts to about 560 billion gallons, providing a system firm yield of about1300 mgd. The Delaware system provides about 50% of the City’s water, the Catskill about 40%, with the remaining 10% provided by the Croton. The system as a whole, which is shown on Figure 1, has been built up over the past 150 years, and is truly a marvel of engineering. The Catskill and Delaware aqueducts both discharge into Kensico Reservoir, which is a daily balancing reservoir located in Westchester County about 24 km(15 miles) north of the New York City line. The two aqueducts extend south for a further 14 miles to combine again at Hillview Reservoir in the Bronx, which provides hourly balancing storage for New York City system. The Croton aqueduct runs nearby as shown on Figure 2, but does not connect into the two reservoirs. From Hillview Reservoir the water is supplied to the city via three main distribution tunnels, known as City Tunnels 1, 2, and 3. City Tunnel No.1 was developed in the 1920s as part of the Catskill system. City Tunnel No. 2 followed in the 1960s as part of the Delaware system. City Tunnel No. 3 (CT3) is partly under construction and partly in operation, and is being implemented to permit the other distribution tunnels to be taken out of operation for the first time for inspection and maintenance. Presently CT3 is supplied with water from Hillview Reservoir via a large underground valve chamber, the Van

Jan 1, 2007

By T. G. Carter

Support system design for tunnels and underground excavations has for many years relied heavily on the use of rock mass classification systems and the Hoek-Brown failure criterion as a means for characterizing rock mass behaviour. Because of their development, both the GSI system and the Hoek-Brown criterion admirably characterize most ?normal? rockmasses from the viewpoint of their behaviour for rock excavations. They, however, run into difficulties when applied at the two ends of the rock competence scale. This is largely because block size and incipient strength are such that rockmass behaviour in these domains tends not to be controlled by interblock shear strength but rather by material strength. At the low end of the rock competence scale (UCSi <<15 MPa and GSI generally <30) discontinuities play less of a role and rock mass strength tends to matrix strength. Similarly, at the high end of the scale (GSI >>65, mi>>15), because discontinuities are now widely spaced, block size becomes so significant that again, intact material behaviour rather than the fracturing becomes the dominant factor controlling rock mass strength. In this paper several case examples are presented to illustrate the application of the high-end (spalling) and low-end (weak ground) transition Hoek-Brown relationships proposed by Carter, Diederichs and Carvalho (2007) as a basis for better defining rockmass behaviour at the extreme ends of the rock competence scale.

Jan 1, 2008

By J. H. East, D. Harrington

"INTRODUCTION Shaft mines, coal and noncoal alike, have a common hoisting problem that remains largely unsolved - how to obtain a mechanical device that will suspend a cage or skip in a mine shaft if the hoisting rope should break or become detached from the cage or skip and that will function effectively under all conditions of service. Safety catches, or safety dogs, as they are commonly named, are installed on nearly all mine cages and many skips operating in American mines, but often, if the hoisting rope breaks, the cage or skip falls to the bottom of the shaft in spite of safety devices, causing much property damage and often fatalities.Available information relative to safety catches for mine cages and skips, desirable characteristics of safety catches and methods of testing safety catches to determine whether they are functioning correctly has been assembled in this publication for the convenience of those responsible for the safe operation of mine cages end skips and, more particularly, to focus attention on the need for a device that actually will stop and suspend a falling cage or skip under all conditions of use and do it without killing or maiming the occupants."

Feb 1, 1948

By Juliana Mendonça Silva de Jesus

O estudo do comportamento de membranas trocadoras de íons em um sistema específico permite verificar a interação de um eletrólito com suas propriedades. No presente trabalho, foram utilizadas soluções de cobre à base de HEDP, proveniente de um banho galvânico isento de cianeto. A membrana utilizada foi a HDX 200 (aniônica) fornecida pela empresa Hidrodex. Amostras da membrana foram submetidas a um ensaio de envelhecimento durante 13, 26, 60 e 90 dias, imersas em uma solução a 5% v/v do banho de cobre. Após o envelhecimento essas foram preparadas para a realização de análises estruturais por FTIR, MEV e TGA. Os resultados obtidos pelo MEV e FTIR mostram que a membrana possui morfologia heterogênea. Além disso, verificou-se pelos resultados da análise térmica que o complexo presente no banho eletrolítico influi no comportamento térmico da membrana.

Aug 17, 2017

By J. Ndlovu, R. Hundermark

Keywords: Anglo Platinum, Polokwane Smelter, pyrometallurgy, metallurgy, platinum, platinum group metals, PGM, base metals, nickel, copper, sulphide smelting, electric furnace, Söderberg, electrode, matte, slag, flash drying, matte casting, crushing, granulation Anglo Platinum?s Polokwane Smelter is situated outside Polokwane, in the Limpopo Province of South Africa. Wet concentrate is received from various concentrators along the Eastern Bushveld Complex, with 60% of the total concentrate received being from UG2 reef and 40% from Merensky reef. The concentrate grade differs from 35 g/t to 110 g/t, and from this a PGM-rich nickel-copper matte is produced. The furnace matte produced is sent to the ACP converter in Rustenburg. The Anglo Platinum concentrators, from which concentrate is received, are Lebowa, Potgietersrus, Amandelbult, and Union, as well as the joint venture Modikwa. The concentrate is fed to two flash dryers that utilise coal-fired, fluidized-bed hot-gas generators to produce the hot gas that will drive off the moisture, leaving a fine bone-dry concentrate to feed to the furnace. The dry concentrate is pneumatically transferred to a storage silo before being transferred to the feed bins situated above the furnace. Lime, if required as a flux, may be transferred separately to the furnace feed bin by a pneumatic system. The concentrate and lime is fed from the feed bins onto airslides and into the furnace. The feed rate is automatically controlled, and the system is set up to optimize the power to feed ratio. The electric furnace is nominally rated at 68 MW and the power is transferred into the furnace using six 1.6 m diameter Söderberg electrodes. Concentrate is melted by energy generated when electric current passes through the electrodes and resistive slag layer. On melting, two immiscible phases form: slag and matte. Furnace matte, containing the bulk of the base metal sulphides and PGMs, is denser than slag and collects naturally at the bottom of the furnace. The furnace is constructed of a combination of refractory brick and water-cooled copper coolers. The furnace sidewalls and hearth are cooled by air drawn through the area by cooling fans. The hearth and matte zone are constructed from refractory bricks. The copper coolers reside only in the slag zone of the furnace along the entire perimeter of the furnace. One staggered row of plate coolers is installed above the waffle coolers along the perimeter of the furnace. Matte is tapped periodically through one of the two matte tapholes into 35-ton refractory-lined ladles, and cast into matte ingots on a casting machine. The cooled matte is discharged onto a concrete slab for cooling and then transferred by front-end loaders to the crushing plant. The matte is first crushed in a jaw crusher and then a Rhodax cone crusher to a size of 2 mm before it is loaded into tankers and sent to the ACP. The low-grade slag is tapped from the furnace through a water-cooled copper insert into a short water-cooled copper ?hot launder? which discharges into a granulation cold launder. The granulated slag slurry flows to three rake classifiers, from which the coarse slag is discharged onto a conveyor to dewatering silos. The dewatered slag from the silos is dumped. The water overflow from the classifiers reports to two thickeners where the water is clarified, and the thickener underflow is returned to the rake classifiers. The smelter is a zero-effluent plant and all the water from the slag silos where the slag is dewatered, as well as the storm water, is pumped to the process water dam from where it is pumped back into the plant for process water use. The off-gas from the furnace is drawn through a forced draught cooler and into a high temperature baghouse. The dust collected in the baghouse is pneumatically transferred into bins above the furnace and is fed via the concentrate airslides. The cleaned off-gas is then vented through the main stack.

Jan 1, 2006

By Daniel P. Lathrop, Leslie C. Taylor, William L. Fourney

Except when the target is on the surface, e.g. a tank track, the most important loading mechanism from a buried charge on a target above it is the impact of soil propelled at the target by the expanding gas from the explosion. Detonation of a shallow buried explosive generally yields an unstable interface between the rising soil and the air which appears to be the result of Richtmyer-Meshkov instability. Irregular “fingers” of saturated sand extend into the air above a more generalized dome of soil. These fingers move at a much higher velocity than the material between them at smaller stand off distances. As a result, the local load on the target at positions on the target at the same distance from the charge may vary by 50% or more from shot to shot or even within a single shot. This variation requires a large design safety factor to assure the integrity of design of mine-resistant vehicles.

Jan 1, 2009

By Rameshwar Sah, Somasekhar Pitchika, Akhil Singh, Seenivasan Rajiah, C. B. Dayanand, G. Balachandran

In the sintering of iron ores, the partial substitution of anthracite coal for coke breeze has been considered to be an effective way of reducing emissions and improvement in sintering properties. In the present study, the combustion characteristics of the anthracite coal and coke breeze were investigated and its influence on product sinter quality and sinter flue gases is being monitored. Pot trials are carried out with different coke breeze ratios, 0%, 40%, 50%, 60%, and 100%. It is found that as the percentage of anthracite coal is increased from 0 to 100%, the sintering time decreased from 24 to 20 min, and the productivity increased from 2.25 to 2.60 t/h/m2. Up to 60% anthracite coal substitution Tumbler index (+ 6.3 mm%), Product yield (+ 5 mm%), and fines generation (− 5 mm%) is found 62.29%, 85.17%, and 15.33%; moreover, hematite ( Fe2O3), magnetite ( Fe3O4), calcium ferrite phases ( CaFe2O4, CaFe3O5), and Silico ferrite of calcium and aluminum (SFCA) are major mineral phases found during microstructural analysis of product sinter. Keywords Sintering · Anthracite coal · Combustion rate · Productivity

Jun 2, 2022

By AMIRA P588 Research Team

This contribution summarises new knowledge and data, obtained during a three year ARCAMIRA funded research project, on the mineralogical and geochemical characteristics of hydrothermal alteration associated with low sulfidation, gold-silver epithermal deposits. These data are used to develop exploration vectors for use at both deposit and district scales, plus techniques have been established to distinguish ore grade epithermal systems from barren or low grade systems. Deposits investigated were Ladolam, Papua New Guinea, Gosowong and Mt Muro, Indonesia, Cerro Vaguardia, Argentina and Bimurra and Twin Hills, Australia.

Jan 1, 2005

Power Point Presentation

Jan 1, 2007

By Barbara Mazzini Loureiro

As placas de circuito impresso (PCI) são materiais heterogêneos e sua composição pode variar em função do ano de fabricação, tecnologia empregada, propósito de utilização, legislações vigentes e país de origem, entre outros. Essas características interferem diretamente no valor econômico agregado a estes resíduos, pois dependem da composição dos mesmos, de tal maneira que as empresas recicladoras tomam como base essas informações no momento da aquisição da sucata. Assim, a classificação e caracterização de PCIs é de suma importância para o mercado de reciclagem de resíduos eletroeletrônicos. A fim de alcançar este objetivo foi realizada cominuição em moinho de facas utilizando grelhas com abertura de 9, 6 e 3mm. A etapa de caracterização incluiu ensaios de digestão em água régia, perda ao fogo, análises química quantitativa por ICP-OES e MEV/EDS. Verificou-se que o lote de PCI estudado possui 39,5% de material cerâmico, 34,5% polimérico e 26 % metálico. A porcentagem em massa de cobre na placa é de 14,28%, de ferro 3,73%, de ouro 0,012% e de estanho 1,29%. O lote não é lead free e é multilayer com quatro camadas de cobre.

Aug 8, 2018

This list is part of the long-range conservation program of the Bureau of Mines and is intended for use by those interested in the Bureau&apos;s publications dealing with oil shale and shale oil. The items included represent 51 years of research by Bureau of Mines employees on oil shale and shale oil and are available at any U.S. depository library. DISTRIBUTION U.S. Bureau of Mines report series contain both free and sales publications. An asterisk (*) designates publications for sale. Such publications can be obtained from Superintendent of Documents U.S. Government Printing Office Washington, D.C. 20402

Jan 1, 1969

By George K. Schenck

This Bureau of Mines publication describes and evaluates a Standard Industrial Classification (SIC) based end-use data system for minerals that is designed to link the demand for minerals to economic activity in commercial uses. The new data system is two-dimensional. The first dimension of technical product classes (TPC&apos;s) measures the consumption of minerals in major primary intermediate products. The second dimension measures the consumption of these TPC&apos;s in SIC end-use sectors in sufficient detail to identify the major determinants of demand for each TPC. Intercomodity comparisons are achieved at the level of SIC two-digit major groups. The methodology was developed so that all available sources of information from Government and industry can be utilized at minimum cost. This information will be supplemented with additional data to be obtained by modifying existing Bureau of Mines canvasses so as to elicit additional quantitative responses from mineral producers. The new data system is expected to improve significantly the ability to forecast demand for minerals, and provide an information base that would, for the first time ever, permit resolution of such questions as trends in substitution among materials and the intensity-of-use of materials in end-use sectors. For the 42 TPC?s identified in the report, data are available for the new system from current sources or, except for three TPC?s that require new canvasses, can be obtained by modification of existing Bureau canvasses.

Jan 1, 1982

By Aram Grigoryan

This paper addresses historical aspects and construction sequencing of the subway complex under Columbus Circle in Manhattan; the structural elements of the rehabilitation and new construction; and the challenges associated with design and construction. PB is providing engineering services to New York City Transit (NYCT) for the rehabilitation of the 59th Street/Columbus Circle Station Complex that services over 150,000 customers daily. The project involves structural repairs, modifications and new construction requiring underpinning and temporary supports, custom framing details, and construction staging procedures to meet stringent limitations within the operating transit station and around the Columbus Circle street intersections.

Jan 1, 2008

By A. B. Desai

The construction of 1144 nos. of piles, each 1.5 m diameter, bored-cast-in-situ type and varying in depths from 6.5 to 23m, has been completed as foundation for 26 piers of 548 m long aqueduct across Orsang river to carry 1128 m3 water of Narmada Main Canal of the Sardar Sarovar Project in Gujarat. These piles are socketed 1.5 m into foundation grade rockmass. The portal system of 44 nos. of piles and pile cap at the top for each pier is analyzed considering the portal fixed at bottom of piles. The borings for pile shaft were done deploying reverse mud circulation rigs and also by conventional chiseling and bailing operations. Besides vertical loading tests and lateral loading test on piles, dynamic tests such as low strain integrity testing on 290 piles and high strain pile testing on 17 piles were also conducted. The results indicated that (a) the settlement/ displacement are much less than the prescribed limits (b) good quality of concrete (c) piles are firmly socketed and (d) piles have adequate structural capacity to withstand the design load.

Jan 1, 1996

By A. G. Doll

"Many power-based grinding models exist, and most operators are familiar with Fred Bond's ""third theory"". Bond's model is most commonly used to describe primary and secondary grinding to product sizes above, for example, 100 µm. Operators sometimes use Bond's equation to describe grinding in situations where it is not appropriate, such as fine grinding below 50 µm. Using an alternative model would be a better choice in this situation.Bond's equation is one in a large family of models. Related equations better suited to fine grinding include the “signature plot”, Von Rittinger's model and Charles' equation. These models have a similar form to Bond's and can be fit to industrial regrind mills and laboratory tests using the simple regression tools in the charts of computer spreadsheets. Operators will find that fine grinding calculations are both easier and more accurate when using the alternative equations to fit their regrind milling surveys or when performing laboratory regrind mill scale-up for plant design.None of these models are new: Charles' equation was published in 1957 and Von Rittinger's model was proposed in 1867. A quick refresh how to apply these equations can turn these oddities from the undergraduate curriculum into useful tools for plant optimization. They can be fit to any type of mill including stirred and tumbling ball mills.IntroductionBuilding a case for fine grind modelling requires reviewing some theory before building a framework for doing fine grinding calculations. The actual calculation procedure recommended is easy and can be applied by plant metallurgists. Don’t be frightened by the theory; the end result is reasonably simple.The observation that mineral breakage is related to the absorption of energy is usually attributed to Von Rittinger (1867). Lynch and Rowland (2005) describe that the ability to empirical test and calibrate energy models of breakage didn’t exist until the widespread adoption of electric motors in the mining industry during the 1930’s and 1949’s. A series of technical papers published by the Allis Chalmers company during the 1940’s demonstrate that they were attempting to do such a calibration using Von Rittinger’s model which is usually stated as: “the energy consumed in the size reduction is proportional to the area of new surface produced.”"

Jan 1, 2017

By K. N. Karparov

The classical limit equilibrium methods are suspected to be ineffective in predicting the potential for highwall failure in many instances in coal mines around the world. Slope engineers have for many years recognized a block thrust failure mechanism for slope failures, but little work had been done before 2000 to explain the actual mechanisms which must be responsible for the failure. The main reason for this is that limit equilibrium methods implicitly assume rigid blocks, and the resulting force equations must be satisfied everywhere simultaneously for them to have any meaning. This paper will show that the material involved in the slope failure is not rigid; indeed it undergoes considerable permanent deformation during failure. This observation allows the authors to treat the block boundaries independently, because they need not maintain a constant spatial relationship with one another, as is assumed in other methods. To enable analysis of this type the authors assume that the weight of the blocks is evenly distributed. This is reasonable, because the slope material is not strong enough to be self-supporting without some sort of constraint, or strong enough to be able to apply point loads to the surrounding material. The purpose of this paper is to extend the practical application of the analytical method developed from mechanism studies to provide an objective assessment of the risk of slope failure, and therefore guidelines for more stable slope designs. This work is based on studies carried out on two failures in an open pit coal mine in South Africa, and provides a methodology to assess the potential for failure more objectively than is possible with currently accepted methods, while at the same time remaining sufficiently simple to allow a ?back of the cigarette box? assessment by geotechnical engineers on site.

Jan 1, 2009

By Daniel Su

Approximately 90% of the primary roof bolts used in CONSOL?s Pittsburgh seam coal mines is 2-piece, 8-foot long, 7/8? (or ¾?), high-strength, resin assisted, mechanical shell tensioned bolt. The remaining 10% is the 2-piece, 8-foot long, 7/8? combination bolt, which employs 4 feet of fast resin to anchor the deformed rebar at the top of the hole. In either system, a 1-3/8? hole is required to accommodate the mechanical shell and the coupler. The cheaper torque-tension rebar system, which is typically fully-grouted with 2-speed resin and which typically provides low bolt tension, is not used in CONSOL?s Pittsburgh seam mines. Rather, it is used in CONSOL?s Central Appalachia mines, where the roof rocks have CMRR rating of 50 or higher. Fully-grouted headed rebars, on the other hand, are used in CONSOL?s room-and-pillar mines. The selection of tensioned versus non-tensioned, fully-grouted bolts for coal mine primary roof support has been debated for the past thirty years. Many researches have been conducted to understand the theoretical bases behind the two systems. This paper describes CONSOL?s experience of using a new fully-grouted, mechanical shell tensioned bolt in the Pittsburgh seam with the development of low insertion force resin.

Jan 1, 2007

By Roderic A. Ellman

The new Woodrow Wilson Bridge (WWB) will replace the existing bridge over the Potomac River to connect Alexandria, Virginia to Prince Georges County, Maryland. The new WWB will extend approximately 1.1 miles across the river, with a 367-ft long bascule span in the main river channel where the water depth is about 36 ft. The subsurface soil profile consists of up to 50 ft of a soft organic silty clay layer that is very vulnerable to scour, underlain by a deep deposit of hard sandy clay. Foundation construction in the Potomac River required the use of cofferdams to allow structural concrete work to be performed in the dry. This paper will the present the types of cofferdams used to construct the foundations for the WWB replacement project. The bridge is primarily comprised of fixed spans in relatively shallow water and a bascule span over a navigation channel in relatively deep water. Foundation construction included the installation of 48? to 72? open end steel pipe piles and cast-in-place concrete pile caps. To achieve the desired bridge appearance, pile caps were required to extend below the water surface and below the existing river bottom in shallow water locations. Conventional steel sheet pile cofferdams with tremie concrete seal were used to construct fixed span, shallow water piers. Selection of deep water bascule span foundation cofferdams was governed by several factors including contraction scour, environmental considerations and cost. Potomac River cofferdams, i.e., relatively shallow depth cofferdams that are supported by the foundation piling were selected. This cofferdam system provided a shallow profile which minimized contraction scour and the amount of filling in the river. Design issues include load selection and cofferdam stability in very soft alluvial soils. Construction issues include erection sequence, tremie concrete mix design and placement procedures.

Jan 1, 2013

By Silvana Costa

In the last two decades, there have been nearly no new mining towns built in Canada. Governments and mining companies have viewed long distance commuting (LDC), commonly known as fly-in-flyout or fly-in mines, as a way to avoid problems associated with building a new community and providing for its sustainability after mine closure. LDC is also considered more cost-effective than building a mine town. The intensification of the use of LDC in the Canadian mining sector has been quite rapid, particularly in northern regions. However, LDC has implications to employees, their families and communities, which deserve further examination, particularly considering the significant expansion in Northern mining and Aboriginal participation in this sector. This paper presents a review of the major issues in long distance commuting, both from an industry and community perspectives. It is a result of preliminary investigation for a PhD research project that will be pursued by a Bridge Fellow and UBC Mining Sustainability Working Group member, and guided by an interdisciplinary research team at the University of British Columbia (UBC). The Bridge Fellowship Program is research-training program linking the UBC?s Faculties of Medicine, Engineering and Graduate Studies. Its mission is to develop creative evidence-based prevention measures for public, environmental and occupational health problems. The SWG is an interdisciplinary student group based in the UBC Department of Mining Engineering, committed to respond to the complex sustainability-related challenges currently faced by the mining industry. In other to pursue this project, it is paramount that industry and local communities alike participate in the development and clarification of research questions as well as in the research design. It is hoped that this paper will function as an invitation for industrial and community partners for such study. The main themes identified for this research are occupational health and safety of LDC employees, family life impacts and community health impacts of this model of resource development.

May 1, 2004

By O. A. Bascur

Ores are becoming extremely variable with mineralogy and hardness disturbing the grinding and flotation circuits. The current grinding and flotation sensors provide large amounts of data for process optimisation. Adding the right context and operational events augments operational knowledge for proactive actions to improve the performance of the grinding and flotation circuits. A data-driven strategy is needed to enable operations, maintenance, and business personnel to quickly and easily take corrective action when abnormal conditions occur. A digital plant template transforms data into operational insights in real-time. It uncovers the hidden, idle and downtime losses. By measuring and managing these unproductive times, people find new ways of avoiding them, improving the profitability of the plant. The information created by the real time analytics enables the calculation of recovery in real time and develops predictive analytics models to find the best operating condition based on the type of ore currently mined. The creation of new workflows and collaboration between mining and concentrator plant and the enterprise, including services providers, are enabled. A grade recovery model is used to identify the best operating conditions in real-time. An optimal Gaudin size distribution shape is used to find the grinding operating conditions that optimise the metal recovery in the rougher sections of the mineral processing plant. Sensors in the flotation circuits enable estimation of metal recovery and determine the optimal froth depth and aeration profiles, using an industrial air holdup flotation model. The implementation of a recovery/grind strategy with industrial examples in non-ferrous metal concentrator is presented in the paper. Keywords: Digital transformation, soft sensors, predictive analytics, grinding flotation optimisation, flotation bubbles, particle size, particle size distribution shape, froth aeration profiles, flotation air hold up model, recovery predictive analytics

Jan 1, 2020