Search Documents

By Bernard Dallaire, Jean Cayouette, Sylvain Duchesne

"Louvicourt Mine's concentrator, located near Val d'Or, Quebec, treats an average of 4,300 tonnes of ore per day composed mainly of copper, zinc, gold and silver. An analysis of concentrator revenues and metallurgical losses shows a potential for additional gain, particularly in regards to precious metals (kustelite) where recovery is usually around 67 -70 %. The planning, installation and trial operational period of two Outokumpu SK-240 flash cells at the underflow of the primary cyclones took two years. The use of (( flash flotation )) technology has made it possible to exploit the favourable conditions at the underflow of the primary cyclones such as precious metal concentration and the presence of liberated coarse chalcopyrite. These conditions permit early flotation (fresh surfaces) of the kustelite and the liberated copper. Since the start-up of the flash cells, the metallurgical gains have turned out to be very positive with increases in metal recovery reflected in appreciable NSR gains. Also, significant savings in reagent consumption and a coarser copper concentrate have made it possible to reduce the drying cycle of the Larox filter presses since the cells were put into operation.BACKGROUNDLouvicourt Mine is operated by Aur Resources Inc. (30% ownership) on behalf of its partners Novicourt Inc. (45%, subsidiary of Noranda Inc.) and Teck Corp. (25%). The mine is located in northwestern Quebec about 600 km north of Montreal and about 25 km east of the mining town of Val d'Or. The mine commenced commercial production in July 1994.The massive sulphide ore deposit lies at depths varying between 450 m and 900 m. Mining reserves (2% Cu equi. cut-off) as of Jan. Is', 2000 are estimated at 7.5 million tonnes of ore averaging 3.4% Cu, 1.8% Zn, 28.0 g/t Ag and 0.9 g/t Au. Delineated ore reserves permit the use of a mechanized transverse blasthole mining method. The extraction order is a typical 1.3.5 mining sequence. Primary and secondary stopes are 15 m wide, 15 to 70 m long (25 m long average) and 30 m high. Backfilling for pillar recovery and regional stability is required."

Jan 1, 2001

By Yeruva Ramanareddy, Sohail Wajid, Ahmed Shaz, K. Bhavani

"CP-06 is an NATM cross passage which connects up-line and down-line metro tunnels near Kilpauk Medical College, Chennai. It lies completely in loose silty sand to dense sand with water table almost touching the ground surface after Chennai floods. Pre-grouting was done before excavation to seal the area and to ensure no-loose pockets. The heading was excavated successfully but while benching excavation huge water ingress started seeping out. Sand also permeated along with water which became unstoppable due to cavity formation and caused the up-line tunnel to sink considerably. A large grouting exercise was carried out with different grout materials and techniques both from the ground surface and inside of tunnel to stop the water ingress and stabilize the tunnel. This paper describes the chronology of events that occurred in the tunnel during CP-06 issue. It elaborates all the different grouting techniques involved in the whole process of the tunnel stabilization. It includes a finite element analysis using Rocscience RS2 9.0 software showing the possible cause of sand incursion with water from the CP invert which lead to the tunnel settlement. This paper also describes the after effects and the lesson learnt from the whole incident.INTRODUCTIONConstruction of Metro Rails has become the latest alternative to cope up with the transportation demand of the growing urban cities population. L&T SUCG JV constructed Chennai Rail Metro Phase II Contract UAA-04 which included design and construction of approximately 4 km of route length of underground mass transit railway including 3 underground stations. This package also includes 12 cross passages which are NATM tunnels connecting upline and down-line side of TBM tunnel for safe evacuation of passengers in case of emergency. As per NFPA guidelines, this is a mandatory structure and there should be atleast one cross passage in 244m tunnel length.CP-06 is a cross passage connecting upline and downline tunnel between Pachiyappa College Station and KMC Station, in Chennai Metro. During the construction of CP-06, heavy water seepage of around 450 liters per minute was encountered during second round of benching excavation after full heading was excavated. An inflow of around 12-15 cum of sand and silt was also observed inside the tunnel along with the seepage water, which created piping inside the TBM tunnel causing it to settle continuously with time. A huge effort was made to stop the water ingress along with loose sand which was causing the running tunnel to settle, involving all possible grouting methods and temporary support installation."

Jan 1, 2017

By NORMAN EBBLEY

NUMEROUS references have been made recently to "Alaska's oil reserves," and in view of the wartime petroleum situation sober thinking demands a dispassionate and scientific study and investigation of these reserves or supposed reserves. The question naturally arises, "Is there actually oil in Alaska, or are the reserves there a supposition?" True, in 1923 President Harding established Naval Petroleum Reserve No. 4 in Alaska, certainly implying that oil was there. This reserve, embracing about 35,000 sq. mi., was set aside on the advice of the Bureau of Engineering of the Navy Department and was based upon the existence of known petroleum seepages at Cape Simpson on the Arctic coast. The Cape Simpson seepages have been known for more than fifty years, but in spite of persistent rumors of other seepages in northern Alaska no definite evidence of their existence has been available.

Jan 1, 1944

By M. A. Upham

"MINING is Canada's second largest basic industry, producing material with a gross value of 2.5 billion dollars, led only by agriculture with 2.9 billion dollars. It pro-vides employment, directly and in-directly, for three quarters of a million people. Since the Second War, the value of mineral production in Canada has tripled. Economists forecast that over the next 15 years its value will triple again. Canada is a basic and leading supplier of nickel, iron, copper, zinc, lead and uranium. It is also a major oil producer, leads the world in the production of asbestos and in five years will be the leading producer of potash, a basic constituent of fertilizer.It can be seen that Canada's wealth and economic progress lies in being a primary producer of economic minerals and in building secondary industries to manufacture finished products from these raw materials. Canada's future in the field of mineral production looks bright, with our resources just starting to be tapped. Outside of the large expanse of Soviet Russia, we are by far the world's most fertile mineral exploration area."

Jan 1, 1967

By L. O. Howard

THERE are three active mines in the Chewelah-Colville district, the United Silver Copper near Chewelah, and the Old Dominion and the Chloride Queen near Colville. The Admiral near Valley is also doing development work. The Chewelah district is in the south central part of Stevens County in the Colville Valley. Chewelah, a thriving town of 1600 people, and the scene of operations of the Northwest Magnesite Co., is about the center of the district. It is situated in a farming community on the Spokane-Nelson branch of the Great Northern railway, about 65 miles north of Spokane. Only two or three of the mines in the district have been extensively developed, although many have been prospected. The general elevation of the valley, is about 1600 or 1700 ft., that of the mountain ranges on each side about 3000 to 4000 ft., with gentle slopes and rounded glaciated tops. Prospecting is often difficult because of much glacial debris.

Jan 1, 1925

By D. J. Steynfaard

Sishen Iron Ore Mine is situated 280 km north-west of Kimberley in the Northern Cape Province of South Africa. The mine produces and sells high quality iron ore of various specifications to various national and international clients. The saleable product is derived from the blending and beneficiation of different types and qualities of hematite iron ore. This paper documents the new developments which were implemented (or are in the process of being implemented) on the mine in the long-term planning, medium-term planning, grade control and material tracking in the beneficiation plant with special attention being paid to the quality of the final, saleable product. The process starts with the long-term planning where the pit shell and pit optimization is determined by Whittle 4X. New developments include the introduction of a linear programming based scheduling system to enhance the long-term schedule generated by Whittle 4X. The LP route was decided on in order to take into account all the constraining factors of the final product that could not be configured in Whittle. To complement this the XPAC Auto Scheduler scheduling package was introduced to do the medium-term mine scheduling. This 18-month rolling plan includes cost parameters to enable the planner to extract a detailed operational budget from the scheduling while ensuring that production standards are maintained and grade constraints are met. The existing grade control system was enhanced with GPS capabilities and a computer system to do material tracking. The high precision GPS system introduced on the shovels allows for the accurate control of the loading procedures at the mining face. Because of the complicated geology and grade composition of blasting blocks it is imperative to accurately differentiate between different materials in the same blasting block and being able to excavate that with the loading equipment. The GPS system on the trucks allows for accurate location monitoring of dumping in order to keep track of specific material types. The state-of-the-art material tracking system developed for Sishen will enable the grade control officer to keep track and record various parameters of the material from its in situ position in the blasting blocks, through the crusher and onto different stockpiles, in various stages of the beneficiation process and onto the blending beds, into the dispatching trains and eventually into the ships for international distribution. These developments elevate the Sishen planning and grade control systems to a new level of service excellence from which management can obtain accurate and timely information on product status. It also enables Sishen to maximize resource utilization while still complying with the tough market constraints.

Jan 1, 2003

At the Prospectors and Developers Annual Convention (PDAC) in Toronto, Canada mining and exploration companies of all sizes were on hand to discuss the year that was and those that will be. The following is a look at some of the companies with Canadian operations that were on hand for PDAC 2009. Iamgold Corporation is a leading mid-tier gold mining company producing approximately 31 t (1 million oz) of gold from seven mines on three continents. With record revenues of $870 million ? up 28 percent when compared to 2007 ? the company is focused on growth with a target to reach 56 t (1.8 million oz) gold production by 2012. During 2008, the company acquired the Essakane project in West Africa. The project is fully permitted, under construction and will contribute more than 9.3 t (300,000 oz) of lower cost production by late 2008. Iamgold increased its reserves by 55 percent, to 385 t (12.4 million oz) and its resources in-creased by 16 percent to 821 t (26.4 million oz) in 2008. Going forward, Iamgold has three areas of focus ? West Africa, Guyana Shield and Quebec ? with seven gold operations, five advanced projects and the Niobec niobium mine included. The Rosebel Mine in Suriname is Iamgold?s fl agship property. With measured and indicated resources of 300 t (9.6 million oz), it accounts for 30 percent of Iamgold?s production. Production there was up 20 percent compared with 2007 and further production increases are expected in 2009 and 2010. Mill expansion and optimization increased throughput from 8.9 Mt/a (9.8 million st) to 10 Mt/a (11 million stpy). In West Africa, Iamgold has joint ventures at Sadiola in Mali; Tarkwa in Ghana; Yatela in Mali and Daman in Ghana. Iamgold also has 100 percent ownership of the Mupane gold mine in Botswana and the Doyon gold mine in Quebec, Canada. Also in Quebec, Iamgold has 100 per-cent ownership of the Niobec niobium mine in Quebec. Niobium is used in high strength specialty steels.

Jan 1, 2009

By M. Foguenne, A. van Lierde, P. Henry

Leaching experiments were carried out on a spent catalyst sample with a honeycomb structure, containing 47.5% Ti, 5.8% Mo, 2.7% Si, 2 035 ppm As, 52 ppm Pb and 8.8 ppm Hg. More than 93% of the Mo and As was removed by direct alkaline leaching after grinding to 80% -36 micrometres. The residue contained 0.3% Mo and 60 ppm As. To obtain a TiO2 matrix with 30 ppm As, acid leaching at controlled pH with 90 kg/t Al scrap was followed by oxidising alkaline leaching. Treatment of the direct alkaline leach solution or of the mixed solutions from the two-stage process involved two successive operations: purification by neutralisation with Al(OH)3 addition to raise the Al concentration to 4 g/l, and ion exchange on Amberlite IRA 94 S resin. Whatever the type of solution treated, elution with 200 g/l NH4OH solution gave an eluate of very high purity containing 164 g/l Mo, less than 70 mg/l V and less than 2 mg/l As

Jun 19, 1905

By D. J. Turk

Stillwater Mining Company’s, Nye Operation has been producing PGM concentrate since 1987.Several expansions have allowed for increasing capacity from the initial rate of 500 tons per day, to its present capacity of 3,000 tons per day. The expansions were performed with minimal impact upon production and maximum utilization of the existing equipment. The latest expansion incorporates a 6’ X 18’ SAG mill, 13’ X 20’ Ball mill, pebble crusher, rougher flotation cells, 1250 Hp tertiary grinding mill, middling and scavenger flotation cells, and cleaner column flotation cells. This paper will describe the concentrator flow sheet, and controls for improved concentrator performance.

Jan 1, 2000

By Christopher Mark

Multiple seam interactions are a major ground control hazard in many U.S. underground coal mines. The two most common types are: ? Undermining, where stress concentrations caused by previous full extraction in an overlying seam is the primary concern, and; ? Overmining, where previous full extraction in an underlying seam can result in stress concentrations and rock damage from subsidence. The National Institute for Occupational Safety and Health (NIOSH) has completed a major study aimed at helping to identify the location and likely severity of these interactions. In the course of field visits to mines throughout the U.S., more than 300 multiple seam case histories were assembled into the largest data base of multiple seam case histories ever collected. These data were analyzed with the multivariate statistical technique of logistic regression. The study also employed LaM2D to estimate the multiple seam stresses, ALPS and ARMPS to determine pillar stability factors, and the CMRR to measure roof quality. The study resulted in the development of a computer program, called Analysis of Multiple Seam Stability (AMSS), which can help mine planners to evaluate each potential interaction and take steps to reduce the risk of ground control failure. AMSS first evaluates pillar design by calculating the single seam Stability Factor (SFSS) using ALPS or ARMPS. It also automatically generates a LaM2D analysis that provides the additional multiple seam stress so that the final, multiple seam SFMS can be determined. The second part of the AMSS procedure builds upon the statistical findings that overmining is much more difficult than undermining, isolated remnant pillars cause more problems than gob-solid boundaries, and weaker roof significantly increases the risk of multiple seam interactions. AMSS quantifies these effects and predicts the outcome in terms of three levels of risk: GREEN (where a major multiple seam interaction is considered unlikely), YELLOW (where adding a pattern of cable bolts or other equivalent supplemental support could greatly reduce the probability of a major interaction.), or RED (a major interaction should be considered likely, and it may be desirable to avoid the area entirely).

Jan 1, 2007

By Robert H. Bedford

The Rogan-Mallery tin property is in the foothills on the south slope of the Tehachapi Mountains, Kern County, Calif. It was first visited by the senior author in August 1942, and exploration by means of trenching and diamond drilling began in May 1944 and was concluded in August of the same year. Cassiterite, associated with iron-rich gossan, occurs in a limestone roof pendant at places near or at its contact with the underlying granitic rocks. The cassiterite grain sizes range from 20 mesh to 150 mesh. Surface and diamond-drill samples showed tin ranging from traces up to 122.6 pounds per ton. Exploration by the Bureau of Mines included 2,100 cubic yards of trenching and the drilling of 11 diamond drill holes totaling 1,000 feet. Dana Hogan, president of the Rogan Petroleum Co. of Los Angeles, Calif.) brought these projects to the attention of the Bureau of Mines in July 1942, and the following month a Bureau engineer made a preliminary examination in company with Hillard Mallery, of 408 Ruby Street, Redondo Beach, Calif., the man who discovered them.

Jan 1, 1949

By Åke Krukka, Heribert F. Broicher

"The iron ores of the Kiruna Mine in Sweden are of exceptional quality but for the phosphorus content in certain zones of the orebody. The prevention of mixing ores high in phosphorus with those low in phosphorus has always been of significant economic importance. The ongoing introduction of tele-mining and automatic haulage by LHDs requires new means in the field of quality control underground, as the experienced miner as well as the underground laboratory assistant no longer are involved in the process. As of 1998 LKAB has been testing prototypes of LIF Analysers for non-contact and real-time measurement of the phosphorus content of ore being transported by LHDs from the stopes to the respective ore pass assigned to a certain ore quality. The principles of the analysis of laser-induced fluorescence, the different test phases and results are described and conclusions made. With bulk sorting of ore underground the mining engineer supports the efforts of the metallurgist in the processing plant.INTRODUCTIONThe Kiruna Mine of LKAB, Sweden is the largest underground iron ore mine in the world. In the early nineties LKAB decided to develop the Kiruna orebody further down from the 775m main level to a new main level at 1045m. This development programme was realised while in the mineral processing section and in the pellet plant further capacity was added (Wyllie 1996).In addition to deepening of the mine, which opened up 330 million tonnes of ore, the exploitation of the so-called lake ore was included in the future planning, adding another 1 15 million tonnes of mineable ore. At an annual production of approximately 20 million tonnes of ore the Kiruna Mine today looks at a developed ore reserve sufficient for the next 20 years.All of the competitors’ ores traded in the world market are from open pit operations. LKAB compensates for the obvious disadvantages by continuous efforts to make the best possible use of her high quality magnetite ore deposit. This objective is realised by combined efforts in the pellet plant, the mineral processing plant and the mine. Propriety processes, latest big scale equipment and high tech solutions for automation lead to high quality sales products at a reasonable cost."

Jan 1, 2002

By E. D. Wilson

A study of factors related to subsidence was specified in a project proposal entitled "Structural Analysis of Block-Caving Operation, San Manuel Copper Mine, Pinal County, Ariz.," approved by the Bureau of Mines early in 1953. This proposal was designed by Charles H. Johnson, then chief of the Base Metals Branch of the Minerals Division, Washington, D. C., assisted by Dr. Leonard Obert, chief of the Applied Physics Branch, Region VIII (now Region V), College Park, Md., and E. D. Gardner, chief mining engineer, Bureau of Mines, Washington, D. C. It read as follows: This project is a study of the mechanics of undercut block caving in a deep ore deposit. The San Manuel is a low-grade disseminated copper deposit containing nearly a half billion tons of ore lying at depths of 500 to 2,000 feet. Development is just starting. Production is to begin in 3 to 4 years (in 1956) at a rate of 30,000 tons of ore a day, or 60,000 tons of copper a year. A Government loan of $90,000,000 /subsequently increased to $94,000,000/ and a long-term Government purchase contract support the capital investment, which will total about $110,000,000.

Jan 1, 1957

By L. Nahai

In two decades Turkey has emerged from the debacle of the Ottoman Empire to become one of the most modern nations in the Middle East. The numerous achievements of this period were remarkable in that they affected human and social, as well as economic, fields. Most of this progress was achieved by Turkey's unaided efforts and the utilization of domestic resources; however, since 1948 various United States aid programs3/ have made significant contributions to increased agricultural and industrial output. Turkey's singleness of purpose in favor of a strong, independent, and prosperous republic has evoked universal admiration and encouraged the hope of stability in the Middle East. Much of the development of the Turkish economy to date has been fostered by the State; however, with growing strength the leaders in 1950 considered the time appro¬priate to relax the nationalistic economic policy and permit private enterprise to play a larger role in increasing domestic output and raising the tempo of industrialization. In pursuance! Of this policy, laws encouraging investment of foreign capital in Turkey and others stimulating development of mining and petroleum enterprises were enacted in 1954. This new legislation, plus the cooperative attitude of the Turkish Government, have encouraged wide interest in the mineral resources of the country.

Jan 1, 1958

By Hannu J. Häkkinen

Metal clusters exhibit unique size-dependent physical and chemical properties that differ from those of bulk materials or large particles. Here we discuss recent theoretical investigations of the catalytic properties of free and MgO-supported gold clusters. The catalytic activity of gold clusters depends sensitively on the environment, charge state, and chemical composition of the catalyst. Relativistic bonding effects stabilize large planar structures for gas-phase gold clusters, and non-compact ?quasiplanar? structures are present as important isomers also for surface-supported clusters. The hybridization of the atomic 5d and 6s states is significantly enhanced by the relativistic effects, and large spatial variations in the nature of the local electronic structure make the low-coordinated gold atoms preferable adsorption sites for oxygen molecules. The adsorbed oxygen molecules are activated to superoxo- and peroxo-states via charge-transfer from gold, and Eley-Rideal and Langmuir-Hinshelwood reactions with CO proceed via low-barrier formation of intermediates, which do not require O-O dissociation as precursors. This facilitates the low-temperature (below 300 K) activity of gold nanocatalysts in CO oxidation. Other gold nanostructures, such as mono-atomic gold nanowires, may also become important prototype systems in chemical sensing and nanocatalysis; here we show that they are active promoters of hydrogen dissociation.

Oct 1, 2003

By Glenn Lyle

CEMI Introduction ? Introduction of the CAF VOD Project ? Who are our partners ? What were the Outcomes What is next

May 1, 2011

By Steven R. Davis

Voyageurs National Park in northern Minnesota, and a 30-mile radius area of influence on the United States side of the International Border, was examined for hardrock (nonferrous metallic minerals and diamonds) mineral potential and environmental sensitivity by the U.S. Bureau of Mines. The investigation also included an analysis of current Metallic Minerals Leasing Rules of the State of Minnesota, and the probable effects of changes proposed to the current rules by the State of Minnesota in order to "encourage mineral exploration and development." The study has determined that the proposed changes to the Minnesota State Leasing rules will have minimal, if any, impact on the likely, foreseeable levels of mineral-related activities in the State as a whole, and particularly, in the area of influence to the Park. Voyageurs National Park management was advised on the extent and character of the proposed rules changes, and on those items of concern meriting a specific and timely response by the National Park Service.

Jan 1, 1994

By C. C. Clark, P. W. Patton, B. M. Stewart

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating those materials-handling tasks in underground mines that appear to generate a high number of injuries. Data from the Mine Safety and Health Administration for the years 1989-1999 were studied to find out if there were any trends in materials-handling accidents and if so, to determine what tasks were involved and the sources of injuries. Several underground coal and metal mines were visited to document innovative materials-handling technologies. Considerations for safety training and mechanization needs for continued reduction in materials-handling injuries are described.

Jan 1, 2002

By Arkady Senchenko, Yury Kulikov

"Basic theoretical grounds of the methods applied for crushing and grinding parameters determination according to international standards are given in this paper. Statistical data about crushability and grindability research are shown. The potential relationship between the values of Fred Bond Work indices and John Starkey indices (Crushing index, Ball mill index, Rod mill index and AG/SAG index) are discussed in this paper. In order to establish correlation between the crushability and grindability indices the analysis of over 2 500 tests for 165 deposits located in different parts of the world was performed. The relationships among different types of energy consumed for crushing and grinding were determined. A method for preliminary estimation of energy consumption in semiautogenous + ball mill grinding circuit is suggested for its application in preliminary technological solutions development and technical-and-economic assessment."

Jan 1, 2014

By J. B. Kitchin

"The design of conveyor belting for use in mines poses problems to the manufacturer that are unique. The challenge to be met is that of the production of a conveyor belt which can withstand use and misuse in an environment that may differ vastly from one country to another, and even between one mine and its neighbour.The development of a product to meet such varying requirements necessitates a protracted program of trials, both in the laboratory and in the field; a new successful development, the only criterion, can be said to have been achieved only after very long-term usage under actual, deliberately chosen, arduous mining conditions.New developments in conveyor belt construction can never stop, no more than can developments in new and advanced mining techniques. A new problem is set-an answer must be found. Some of the problems are noted here, and answered where possible, in what must after all be little more than an excursion into a very comprehensive and detailed subject."

Jan 1, 1967