Search Documents

By Naresh Koirala

The Greater Vancouver Regional District completed installation of a 2.5 Km long, 2400 mm diameter concrete sewer in Delta, British Columbia in 2000. The sewer traverses through area of peat and soft ground. The ground investigation along the sewer alignment consisted of cone penetration tests and auger drilling with standard penetration tests. The gravity sewer is supported on precast, pretensioned spun concrete piles imported from Malaysia which had never been used for a major project in North America. The capacities of the installed piles were tested using pile driving analyzer (PDA) and three static load tests. A total of 46 PDA tests were carried out during pile installation. The paper describes the pile vetting process the owner went through prior to accepting the piles for use in the project and performance of the piles. It compares the pile capacity estimated from the PDA tests with that estimated from soil mechanics methods using data from cone penetration tests and standard penetration tests. The ranges of estimated capacities calculated by different methods are discussed from design capacity selection considerations.

Jan 1, 2004

By John Vynne

Too often, a mine’s operations, including drilling, blasting, loading, hauling, crushing, processing, etc., are considered independent steps, rather then a continuous process. In fact, these are interdependent operations with each step in the process having an impact on subsequent operations. If the effectiveness of the drilling and blasting operations can be improved, they will impact the entire mining process. Some of the resulting improvements include: level benches on grade; fragmentation and diggability with the result being reduced loading times; haul cycles improvements; and the crushing and milling operations will be more efficient and less energy consumed. Thunderbird refers to this as “Drill to Mill” information cycle or process. This paper focuses on two of the technological enhancements Thunderbird has added to its drill monitors that allow the mines to impact the “Drill to Mill” concept. These enhancements are: incorporating global positioning satellites into drill monitors; and radio off-loading of data. Thunderbird is part of the Integrated Mining Systems (IMS) alliance. IMS offers the mining industry the most comprehensive line of monitoring and navigation products available today for mobile mine equipment. In addition to Thunderbird’s drill monitors and GPS systems, the product line includes: Fleet Management Systems for trucks and loaders; dragline and shovel monitors; GPS based navigation systems for shovels, dozers and other mobile equipment; and surveying systems. IMS uses common communication systems, operating systems, and hardware components in order to provide a truly Integrated Mining System.

Jan 1, 2000

By Jerry C. Tien

Changes and the pace of change in China’s coal industry have been extraordinary during the past several years. At least 35 of the 94 former coal bureaus have been restructured into different mining companies and groups. Some of the more productive and efficient ones were further strengthened through consolidation and expansions. And several have even formed, or are in the process of forming, strategic alliances with utility companies, railroads, ports and chemical companies to secure additional reserves and coal sales. In addition, the improvement in coal pricing during the past two years has enabled China’s coal industry to move ahead with some needed changes. Coal mining accidents, though, remain a major concern for the Chinese government. Accidents remain high even though the government has made efforts to shutdown more than 55,000 unlicensed, unsafe small coal operations throughout the country.

Jan 1, 2003

By L. M. Gould

"Syncrude Canada operates the largest oil sands crude oil production facility in the world and produces over 13% of Canada’s total oil requirements. To achieve this, Syncrude mines the oil sands in open pits, extracts the raw oil known as bitumen from the sand using water-based processes and upgrades it into sweet light crude oil by fluid coking, hydroprocessing, hydrotreating and reblending. The final product, Syncrude Sweet Blend (SSB), is sent by pipeline to three Edmonton area refineries and then to pipeline terminals which ship the SSB to refineries in Canada and the United States.As parts of the Mildred Lake base mine reached their economic life, they were replaced with new facilities at the Aurora Satellite mine. Aurora is situated on Oilsand Leases 10, 12 and 34, 35 km northeast of the Mildred Lake facility (Fig. 1).In 2000, the first hydrotransport low-energy extraction production train started up at Aurora. A second production train is scheduled for start-up in 2003. Open pit mining at Aurora occurs using two hydraulic shovels, two cable shovels, and trucks ranging from 320-ton to 380-ton payload capacities (Fig. 2).Once the oil sands is excavated, the trucks dump the ore into a crusher designed to break up the big lumps of oil sands and rock at peak rates of 11 000 t/hr. The ore is then transferred by conveyor to a surge pile and then to a mixing box which combines the oil sands with hot water. Following bitumen separation in the primary separation vessel, froth is delivered to Mildred Lake for processing via the intersite pipeline (Fig. 3).The goal of this paper is to illustrate how high precision shovel GPS (HPGPS) is being used at the Aurora mine to aid in mine planning. This can be accomplished by first describing the function of the mine planning department, describing the Aurora orebody, and finally explaining how the HPGPS system functions and how it is employed at Aurora.The short range mine planning department ensures a steady supply of ore is delivered to the plant at the desired grade in a sequenced and economical manner. This is done by creating a mine plan that consists of shovel dig locations that require the shovels to mine in a specified area at a specified elevation."

Jan 1, 2002

By Pound J. R

THIS mine, which is the property of the S. and M. Syndicate, London, is located at Moina, in North-West Tasmania, 18 miles from Stavertorr railway station and 36 miles from Devonport. There are metalled roads from both of these places, and, althoughhilly, these are good for team or motor traffic. Mails and passengers are provided for by a tri-weekly coach service from Sheffield, a railway town, distant 23 miles. The Moina mining field is situated on a main spur between the Forth and Iris Rivers, andat an elevation ranging from about 500 ft. above sea-level at the Forth River to 2400 ft. at the All Nations mine. The elevation at the mine office of the S. and M. mine is 1900 ft. The average annual rainfall, as recorded for the past eight years, is. 68 in.This inclildes, however, a couple of years during which the rainfall was much above normal, and taken over a longer period 60 in. would be nearer the average.

Jan 1, 1919

Real Time and In Situ Measurement of Elemental Composition Using Lasers

Sep 13, 2010

CENTRAL mine ore consists mainly of galena and marmatite in a siliceous and rhodonitic gangue, the average assay values being approximately 11.5 oz. per ton Ag, 14.5% Pb, 14.5% Zn, 1.3% Ox Pb, 0.3% Ox Zn.Owing to the 1923 fire in the underground workings, much of the ore now being mined has been subjected to a certain amount of oxidation, as shown by the oxidised values above.This factor is of great importance from a flotation point of view, as a sulphide surface which has been subjected to the influence of oxidation is not as amenable to flotation concentration as a fresh sulphide surface. The importance of this factor is increased when a differential flotation is to be made, and, as in the case of Central mine ore, the sulphide, which is to be floated first, has been oxidised...

Jan 1, 1931

By Holdgate G. R, Thompson B. R, Webster R. L, Bolger P. F

The Gippsland Basin in south-eastern Australia has an area of approximately 46 000 sq km. It is one of the world's major coal and petroleum bearing basins, with most of the former occurring in the smaller one fifth on-shore part. The stratigraphy, structure and economic resources of the Tertiary sedimentary pile is now well known through extensive drilling for coal and petroleum. In contrast, the older Cretaceous sequences through their lesser economic importance are relatively less explored. The sedimentational history of the Gippsland Basin has largely followed along similar lines of development to the many other southern Australian basins since the Cretaceous break-up of Gondwanaland. However, the scale of accumulation of coal and hydrocarbon source rocks is unprecedented and differentiates this basin, for reasons less well understood, from the others. Large scale open cut brown coal mining since the late-1920s has been carried out in the western extremities of the basin, while vigorous extraction of some two thirds of Australian petroleum products taken place in the offshore part. Brown coal seam thicknesses and economically winnable reserves are huge and outrank most other brown coal basins of the world. Development of the resource currently meets the need for electricity generation throughout the State of Victoria, but other future developments such as conversion to oil, being investigated.

Jan 1, 1992

By A. F. van Weele

In general cast-in place piles will have an irregular pile shape. However, it is possible that these irregularities are so large that they may lead to pile deficiencies. It is very rarely possible to examine the pile foundations visually. Also the performance of a static or dynamic load test on each individual pile is not practical and much too expensive. This is the reason why pile integrity tests have been developed: to reduce the risk of inadequate pile foundations by performing a simple test. Pile integrity tests are non destructive tests which are carried out after a pile has been installed. Over the years a number of techniques have been developed of which the most important techniques are briefly described in this paper. Of all pile integrity testing methods, Sonic Integrity Testing is the most widely used method in western Europe. This method has been developed by TNO some 15 years ago. Since then the method has been improved, largely due to advances in micro-processing. A major improvement was made by the introduction of digital signal processing techniques. This made the Sonic Integrity Testing method more accurate (smaller defects can be detected), faster (more than 200 piles can be tested on a single working-day) and more reliable (the results are easier to interprete). A few cases will be presented which will show the usefulness of the Sonic Integrity Testing method. In one of these cases, a helpful tool for interpretation of the results is explained: the Sonic Integrity Testing Simulation program TNOWAVE. Notwithstanding the fact that Sonic Integrity Testing is a powerful method, it has also some strict limitations. These will be discussed at the end of the paper.

Jan 1, 1987

By Gilles Rousset

This paper presents laboratory experiments conducted on hollow cylinders samples. The advantage of such a geometry is to approach in situ conditions around cylindrical openings (lined galleries, boreholes, ...). Many authors have been interested in this kind of problem, especially for borehole stability applications (for references see Guenot 1987). However, as long as we know, time-dependent behavior has not been well studied. For this purpose, we have set up two different types of tests on a deep clay : - Quick unloading test, to assess the influence of unloading rate on mechanical response and the failure modes. - Creep and relaxation test, to compute the time dependent overall deformation of the hole wall as well as to plot long term convergence-confinement pressure curve. The experimental results are then compared with those given by a theoretical model developed in our laboratory, well fitted with the tested material.

Jan 1, 1989

By da Silva C A, Tenorio J. A S, de Assis R M, de Oliveira J R

For Fe-Mn alloy production, two reactions are responsible for this process: the MnO reduction in the slag and the carbon dissolution in the bath. The smelting-reduction process has been studied as alternative route to be used to produce alloy so as steel. This technical paper presents some initial studies to be used to determine the main ways that one can have for the mechanisms for this reaction. The limited factors like mass transport or chemical reaction were analysed. The Mn content in the bath were varied and it was concluded that by increasing the former, dissolution of Mn into the bath was increased, so as a reduction of MnO in the slag. For carbon dissolution, it was used a experiment with a stationary bar, this one was added into the bath, after ten minutes probes were catched, by temperature 1600¦C, for the dissolution of MnO, one graphite crucible was employed, after 45 min the slag and alloy were analysed. After the experimental part, some curves were plotted against time, based on these graphics, and kinetic analysis was made.

Jan 1, 1999

By L. R. Plitt, A. A. Turak, B. C. Flintoff

"Since the publication of empirical cyclone models by Lynch and Rao in 1975 and by Plitt in 1976, the technical literature on this subject has consisted primarily of reports of applications, with only a few articles discussing basic modifications or enhancements in model form. In fact, most of the modelling eff ort in this period has been concerned with theoretical models based on the hydrodynamics of multiphase flow. (Preliminary resutls have been encouraging, however, it will be some time before this approach reaches the practical application stage.) This paper presents a review of empirical cyclone modelling technology, with an emphasis on developments since the mid 1970s. The topics addressed include homogeneous and heterogeneous ores, parameter estimation techniques, parameter confidence intervals, and the introduction of a new conceptual model of cyclone operation.IntroductionSince their first reported application in the mineral industry by Driessen (1939), cyclones have become a common unit operation in all of the process industries. The widespread use of the cyclone stems from its relative low cost and its versatility. It can be employed to carry out liquid-liquid, solid-liquid and solid-solid separations. It is the area of solid-solid separation which is of greatest interest to a mineral processing engineer. Historically, this area was divided into two application categories: (I) Separation according to density, the cyclone washer, and, (2) Classification according to particle size, the cyclone ciassifier. (When water is the carrier fluid, the cyclone is more often called the hydrocyclone. For the purposes of this paper the two names are used interchangeably). Classification is the principal application in mineral processing circuit s. Within this category, the cyclone is most commonly employed to provide some positive control over the size distribution of product from a grinding circuit. Other uses include sand-slime separation prior to froth flotation and mill tailings treatment, either for dam construction or in backfill preparation."

Jan 1, 1987

Study on Influence that Styrene-Phosphoric has on the Surface Property of Rutile Minerals

Sep 13, 2010

By J. D. Miller, C. L. Lin

Filtration of fine particles involves filter cake formation and removal of surface moisture by drawing air through the porous structure. Accurate assessment of the transport properties of porous media (in this case, filter cake) is of major importance in the development of improved filtration processes. Implications from these studies are important in the design and operation of filtration equipment in order to enhance the efficiency of this important solid-liquid separation process. The microstructure and connectivity of pore space are important features necessary to describe detailed fluid flow phenomena in filter cake during fine particle filtration. In this regard, 3D characterization of pore structure is essential. The pore structure has to be described by parameters which are of special relevance to the interpretation of fluid transport phenomena. These parameters should be based on directly measured variables of the pore system and not inferred from indirect variables (such as those determined empirically from transport processes) valid only for a particular pore structure. In this way fundamental relationships between pore structure and fluid transport at the microstructure level can be described. In order to achieve this level of sophistication the three-dimensional interconnected pore structure of filter cake must be determined. Study of fluid transport phenomena in filter cake using x-ray microtomography to characterize the complex three-dimensional pore geometry is discussed. On this basis the Lattice-Boltzmann (LB) method is used to simulate and to establish a fundamental relationship between pore microstructure and effective transport coefficients.

Jan 1, 2002

By Donald R. McMahon

This paper presents a unique case history that documents the use of a braced secant pile wall to underpin a heavily loaded footing inside of a manufacturing plant. Construction of a pit for a new manufacturing process directly next to the footing necessitated the underpinning. The footing supports an overhead crane that needed to remain operational throughout construction of the pit and therefore, settlement of the footing could not be tolerated. The base of the footing was about 7.7 feet above the base of the 17-foot deep excavation. The footing bears on a silty clay deposit that grades from a stiff consistency beneath the footing to a soft/medium consistency near the base of the pit excavation. This paper describes the design and construction of the secant pile wall and bracing to control wall deformations, ground movements and settlement of the footing. The footing was monitored for settlement throughout construction of the pit and no measurable movement was observed.

Jan 1, 2006

By Alexander J. Verstraeten

The design and construction of foundations for power transmission line towers present some special problems. This paper describes a system of design and construction for these foundations that was developed in Europe and has attained general use there because of its reliability and cost effectiveness. Transmission line foundations distinguish themselves by having to deal not only with compressive and lateral loads, but with uplift loads and, because of the wind (in some regions earthquakes), with dynamic loading. The construction of transmission line foundations distinguishes itself mainly in the great number of inaccesible locations involved, resulting in extensive geotechnical investigation and logistical problems in moving men, materials and equipment.

Jan 1, 1987

By M. G. Maruma

The effect of the amount of cold reduction and annealing temperature on the evolution of the texture of AISI 441 steel is reported. The steel was cold rolled by 62%, 78%, and 82%, followed by isothermal annealing of each sample at 900°C, 950°C, and 1025°C for 3 minutes. The crystallographic texture was determined by Phillips X?Pert PROMPD texture diffractrometer. Microstructures were characterized using optical microscopy and scanning electron microscopy (SEM).The results show that sample that received 78% cold reduction and annealing at 1025°C presented the highest Rm-value and lowest ?R-value, which would enhance its deep-drawing capability. In addition, this sample showed the highest intensity of shifted ?-fibre, notably {554}<225> and {334}<483>. It can therefore be concluded that the ?-fibre, which favours deep drawing, is optimal after 78% cold reduction and annealing at 1025°C.

Jan 1, 2013

By T. A. Grammatikopoulos, B. Vasily, A. H. Clark

"The St. Lawrence deposit is a large wollastonite skarn (ca. 9 Mt @ 41.3% wollastonite) adjoining the gabbroic-to-syenitic Leo Lake pluton in the granulite facies Frontenac Terrane of the Grenvillian Central Metasedimentary Belt. It occurs within a horseshoeshaped horizon of quartzite, open to the east. The skarn extends over 1.2 km2, and comprises wollastonite-dominant, wollastonite-clinopyroxene, and diverse quartz-feldspar-sulphide (-titanite) layers, interbanded with, and strongly folded within, the quartzite. As in the world-class wollastonite deposits of the Willsboro district, New York, no carbonate protolith is preserved, and calcite is a negligible constituent of the mineralized zones. Wollastonite development is nonetheless ascribed to metasomatism of a metacarbonate unit by magmatogene, silica-rich, CO2-poor (XCO2 < 0.05) fluids, at P = 350 MPa and ca. 560°C, or, alternatively, 550 MPa and ca. 630°C.Several high-grade zones, averaging >40% but locally exceeding 80%, of translucent, white, tabular wollastonite grains, with lengths of 0.2 cm to 5 cm, have been delimited by drilling. Preliminary beneficiation studies yield high aspect-ratio and high-purity (low Fe and Mn) concentrates.St. Lawrence compares favourably to other known prospects and operating wollastonite deposits: having good chemical and physical properties, low iron content, and high aspect ratios (>20:1). In addition, the deposit has a favourable size and location, and will benefit from a low Canadian dollar. Canada currently has no wollastonite production."

Jan 1, 2003

By W. B. Berwald

[Accurate ~cusirc::ie t of euusu.rface r,resw rus £Uld tee:: ?er:~t:,res in producin+ oil and as wells is one of tine ast iy,ulortant steps ever t,.s:en to place the rprwctice of retroleum ,-iroduction on an exact scientific basis. i&apos;reerures and teial.or-tures in a -petrolcuia r4:, rvoir. have a rn..r..ed influence over the o:wvement of oil and ~c s both within the. reservoir and t~:rou,=Ii the various-size "flow otrin;;u" of proLucin,; wells to tine surface. Knovrled: ?c of theso fc,.ctgrs form a Laois for cny attei:ant to [.,-~ly eciantific j:cthods to the solution or analysio of mc.nj proble;ae encountered in the production of oil and 1c_c, Without a.ccur:tc mcaaurx,ients of reosures r:.nd tcn::paratuxes within the rocervoit and -well &apos;flo-,r strinL:s" tae aI,licution of w.ny proved enbinecrin and scientific princiy-,loo is on %,]

Jan 1, 1935

By Yvone Franco Crosato

The dense population of Hong Kong requires the construction of tall buildings in reclaimed areas or perched on the slopes of the many hills. The large loads to be supported are carried by deep foundations. Many of those are bored piles, to rock, of diameters up to the 3.0 m. of today.

Jan 1, 2000