Search Documents

By D. T. Bergado

The uppermost subsoil profiles of the Bangkok plain can be divided into four layers, namely: weathered clay, soft clay, stiff clay, and dense sand layers. The soft Bangkok clay is a normally consolidated marine clay with built-up preconsolidation effects and overlain by a weathered crust. Up to the present, a large number of full-scale tests on excavations and pile foundations has been made by numerous investigators. Based on these results, the available data are reviewed and evaluated. The results show that for test excavations, the excess pore pressures were overpredicted by the existing theories. The vertical and lateral movements in the excavations can be predicted by the bilinear and non-linear finite elements using appropriate modulus values. Relationships among probability of failure, safety factor, and safety margin of the excavation were also obtained. In the case of pile foundations, good agreement between the measured and predicted ultimate pile capacities were obtained for long piles. The adhesion factors ranged from 0.4 to 1.0 while the average skin friction factor was found to be 0.33. The ultimate capacity of the pile was also predicted successfully by using the Dutch cone data. For lateral deflection of piles, Davisson and Gill's theory predicted well in the low deflection zone while Poulos' theory agreed well in the high deflection zone. From the probabilistic analysis of ultimate pile capacity, the probability of failure was related to the central factor of safety. The piles usually used in Bangkok area are mainly precast concrete piles

Jan 1, 2010

By Moskovits E. E

Spodumene was recovered from pegmatite by flotation in laboratory and pilot-plant tests using an anionic collector emulsion. A similar process applied to beryl pegmatite gave encouraging results.INTRODUCTIONOver the past two decades lithium and beryllium have aroused increasing interest in the metallurgical world. Both these light metals have potential uses in nuclear shielding and cooling and in lightweight alloys, and there is a growing demand for lithium chemicals for ceramics, air conditioning and lubricants. The use, technology and history of lithium has been surveyed by Schreck (1961).For many years, the only commercial production of lithium and beryllium was from pegmatite deposits amenable to hand cobbing. The most important minerals of these ores are spodumene and beryl, which are respectively lithium aluminium silicate and beryllium aluminium silicate. Norman and Gieseke (1940) investigated the treatment of lithium ores by froth flotation. The process of flotation of the pegmatite constituents away from the spodumene was applied commercially in 1951, and the operation has been described by Goter, Rainey and Hudspeth (1953). Subsequently, the flotation of the spodumene from the pegmatite was studied by Munson and Clark (1955) and Browning and McVay (1961), and this method has superceded the reverse flotation process commercially. Muskett, Tasker and Hobson (1962), in applying the method of Browning and McVay in pilot-scale tests, reported difficulty because of activation of quartz and felspar by iron salts introduced during milling of the ore.The flotation of beryl, reported by Ashton and Weir...

Jan 1, 1963

By James E. Parkes

The Silver Spring Transit Center is a new three-level transit center that will include bus loops for County, Metro and intercity buses, parking, and retail space. It replaces an existing bus station and connects to a busy metro rail station in downtown Silver Spring, Maryland. Significant site constraints in both plan and profile had to be dealt with in developing a design for support of the structure. Over 90 rock-socketed drilled shafts ranging in size from 3 to 7 foot in diameter were ultimately used to accommodate the limited space and large column loads, and to adapt to the variable rock surface at the site. Site access during design was limited due to the existing active bus station, so contract documents were adapted to include further explorations. Differences in anticipated and actual field conditions regarding the depth, quality, and variability of the rock had to be overcome in construction. Osterberg Load Cell testing during construction allowed for verification and optimization of the shaft design. Additional issues dealt with on this constrained site in an urban setting included construction staging issues, such as working around specialty contractors for tieback walls, blasting operations for rock excavation, productions issues for hard bedrock, as well as coordination issues with third parties, most notably the Washington Metro Area Transit Authority. Aspects of the foundation design and optimization, preparation of the contract documents to deal with the complicated nature of the project, and lessons learned from construction are also discussed.

Jan 1, 2011

By Steve Kral

The mining industry has had three difficult years. Commodity prices have remained low and investor confidence in the industry has been shaken. And even though the Asian economy appears to be improving, it will be some time before this improvement will translate into better commodity price conditions for mining. In addition, increased environmental and social restrictions that have been placed on the industry in developed and developing countries have made mining a more difficult proposition. And, if that is not enough, the global mining industry has found itself in fierce competition with Internet businesses for investor capital. Despite that gloomy picture, more than 10,500 mining industry professionals from about 70 countries gathered in Toronto, Ontario March 5-10, 2000 for the Mining Millennium 2000 conference. This meeting was a joint effort between the Canadian Institute of Mining, Metallurgy and Petroleum(CIM) and the Prospectors and Developers Association of Canada (PDAC).The joint meeting also featured two trade exhibitions and more than 150speakers. PDAC’s trade show attracted about 400 exhibitors and an additional 200 in the concurrent Investors’ Exchange. CIM’s exhibition attracted about 600 equipment and service companies.

Jan 1, 2000

By Eric R. Borys, Amaneh E. Kenarsari, Brett Gitskin

This case study discusses impacts of excessive Earth Retention System (ERS) lateral movement at a project in city of Chicago. The ERS (cantilevered sheeting) moved inward towards the excavation and caused lateral displacement and cracks in six drilled shafts located about 1 to 2 lateral feet (0.3 to 0.6 m) from the face of the sheet pile wall. Up to 9 inches (23 cm) of horizontal movement was observed on top of the supporting sheet-pile. Similarly, survey measurements showed the top of the drilled shafts moved laterally up to 8 inches (20.3 cm). To evaluate the cause of failure and determine a remediation solution, the soil, shaft and site conditions were investigated. Pile Integrity Tests (PIT) were conducted at the affected drilled shafts. The shafts with identified anomalies were cored and video-recorded. The cause of the failure was determined to be related to variable soil conditions across the site, deeper excavation (i.e., increased effective ERS wall height), and other differences between design and as-built conditions. Internal bracing, in the form of walers and rakers, was installed to limit further movement of the sheet pile as a short-term solution, with additional grade beams framed into the basement slab-on-grade as a long- term solution. Five of the six cracked shafts were spliced with reinforcing bars and high strength grout and one shaft was replaced. INTRODUCTION The subsoil in the Chicago Area mostly consists of glacial till clays underlain by water-bearing granular soil over bedrock. The glacial clays have very soft to medium consistencies for a typical thickness of 30 to 50 feet (9.1 to 15.2 m) below which hard clays (Hardpan, i.e., heavily over-consolidated clay soils) are encountered. The soft clays are often referred to as the “Chicago Blue Clay”. Beach Sands are also found above upper soft clays in several areas, especially within a three-mile strip near Lake Michigan (Peck and Reed 1954). Due to the existence of soft clay in Chicago area, supporting the mid to high rise buildings on drilled shafts extended to Hardpan is a common practice in modern building design. In the early 19th century it used to take about 3 weeks to excavate 1 shaft hole and about 1½ days to fill the shaft with concrete in Chicago (Manierre 1916). The early 19th century methodology of excavating a shaft consisted of hand digging the shaft, installing wood lagging as temporary shoring with spoils removed with a rope and pulley system from the surface. Today, the excavation of a typical drilled shaft in Chicago uses heavy drilling equipment and requires much less time for excavation and concrete placement. It is not uncommon for contractors to excavate shafts and place concrete at a rate of about 2 to 5 drilled shafts per day (with one drill rig).

Jan 1, 2018

By A. K. Singh

Between the main fan and the coalface in a mine a lot of air is lost through leakage at stoppings, doors, air-crossing etc. so that a much larger quantity of air has to be circulated by the fan in order that the stipulated quantity of air reaches the face. Stoppings are of vital importance not only for effective ventilation of underground mines but also for isolation of areas affected by fire or susceptible to spontaneous heating. Generally, isolation stoppings are made of brick in cement mortar. If the area is far from the pit or unapproachable, it is very difficult and sometimes impossible to build these stoppings. To overcome these difficulties, particularly near fire affected zones, an alternate successful attempt was made in Indian mines to make a plug underground, from surface through borehole, using cement concrete. In this paper the salient features of the methodology adopted for construction of the plug and the experimental procedure for the measurement of air leakage by SF6 tracer gas is described. Measurements of air leakage through rows of ventilation stoppings in two mines viz. Moira (Jambad and Kajora seams) and Kuardi11/12 (Niga seam) collieries of Eastern Coalfields Ltd. (ECL) have been incorporated. Results of experiments conducted at the Central Mining Research Institute (C.M.R.I) to determine leakage through25 and 38 cm thick brick stoppings are also discussed. Results of all these studies are compared, which show that the efficacy and reliability of the remote filled cement concrete plug in respect of air permeability is satisfactory.

Jan 1, 2004

By Parker A. J, Muir D. M

Solutions of acetonitrile in water dissolve water soluble copper(I) chloride. Removal of volatile acetonitrile from the resulting solutions, by distillation with low grade steam, precipitates pure copper(I) chloride. This is used to purify a crude copper chloride sublimate from the chlorination of nickel matte but is applicable to other sources of copper(I) chloride. The pure product can be converted to pure copper(I) oxide, copper(II) oxychloride or pure copper metal directly.

Jan 1, 1980

By John Marsden, Mike Botz

A variety of modeling techniques can be utilized to forecast metal production at heap leaching operations. These approaches reflect a wide range of complexity, flexibility, time to implement, cost, and accuracy. For many operators, a spreadsheet-based modeling technique is attractive since the calculations are directly accessible, models can often be developed by site staff, and the results are generally easy to extract and interpret. The authors have developed a spreadsheet-based modeling technique that provides a high degree of flexibility, while still considering detailed operating information for ore properties, leach kinetics, scaleup factors, lift height, and in-heap metal inventories. The technique involves establishing kinetic leach curves for each ore type to characterize metal extractions, followed by application of separate metal recovery curves to define the rate at which leached metals exit the heap in pregnant solution, taking into account delays due to the in-heap solution inventory. At any point in time, the difference between total metal extracted and total metal recovered is equal to the in-heap inventory of the leached metal. This modeling technique is particularly useful for larger multi-lift heaps where delays in metal recovery are appreciable due to in-heap solution holdup. The technique is also applicable to sites with multiple heaps, leach cycles, and/or metal recovery plants (e.g., carbon columns for gold; solvent extraction for copper). This paper describes the modeling technique, including input data required and methods for defining kinetic leach curves and metal recovery curves. The technique is compared against an alternative spreadsheet technique using a simplified in-heap solution inventory calculation to forecast metal production, which has proven to be effective at a number of sites.

Sep 3, 2019

Small scale' table concentration tests have many critics. Many metallurgists consider that such tests are of problematical value because of the difficulties involved in conducting and interpreting them.Many kinds of small-scale ore dressing tests are difficult to conduct, and there is, perhaps, good reason for thinking that table concentration tests are amongst the most difficuIt.Interpretation of results from small-scale tests is the responsibility of the metallurgists and engineers in charge, and it is often held that small-scale table concentration tests are particularly difficmlt to interpret.TESTING FOR TABLE CONCENTRATIONOn analysis it appears that the difficulties encountered in conducting small-scale table concentration tests are of three fairly distinct kinds. Firstly, there are difficulties due inherently to the smallscale nature of the operations; for example the smaller width of all mineral bands on the table and the less complete separation due to the shorter length of travel between the feed and discharge points.Secondly, there are the effects of batch operation owing to the fact that the mineral particles behave differently during the initial period when the sample is just beginning to spread over the table, the middle period when feed and discharge are even and continuous, and the final stage, when the last of the sample has been added and the table is beginning to empty itself.

Jan 1, 1954

Kinetic Study on the Leaching of Vanadium from LD Converter Slag Using Sulfuric Acid In order to reduce the environmental impact due to land disposal of LD (Linz-Donawitz) converter slag from steelmaking plant and to valorise this waste material, an acid leaching study was carried out to assess the effect of several parameters on the kinetics of vanadium dissolution. The characterisation and morphology of the feed investigated using XRD, XRF. The factors influencing leaching vanadium such as particle size, temperature, slurry density and the concentration of sulfuric acid were investigated and optimised. The maximum vanadium recovery about 95 per cent achieved at 70¦C, S/L: 1/15, acid concentration: 3M and for 150 minutes of leaching time. The dissolution of vanadium in sulfuric acid shows that there are two stages in the kinetics of leaching. At the first 15 minutes, there is a sharp increase in the amount of vanadium extracted and at longer leaching time, the extraction increase slightly. In the present work, the shrinking core model (SCM) was used to describe the acid leaching of vanadium compounds. A summary of the controlling regimes in the SCM are examined below for short time (less than 12 min.) and long time (more than 30 min.) stages. So, it was found that the kinetics of leaching in both stages is controlled by solid product diffusion regime.

Sep 13, 2010

By Rómulo Mucho Mamani

El presente trabajo señala el uso de la tecnología existente en INGEMMET para el servicio de los operadores mineros de pequeña escala, orientados fundamentalmente a la explotación del oro. En este sentido, el uso del conocimiento y de los instrumentos informáticos son elementos que facilitan la difusión de la información geológica para este fin, los mismos que al ser interpretados en laboratorio y contrastadas en el campo, ofrecen resultados de relevante utilidad para la toma de decisiones y coadyuvan al proceso formalizador del subsector.

Sep 12, 2005

By Matthew I. G

A new process for leaching zinc sulphide concentrates with gaseous mixtures of SO2 and O2 in aqueous solution is described.The reaction of SO2/O2 with Rosebery, Mt. Isa, Broken Hill and Elura zinc concentrates yields zinc and iron sulphates, elemental sulphur and some sulphuric acid. Rates of zinc extraction are controlled by a surface chemical reaction without apparent interference from the elemental sulphur layer for SO2 concentrations up to 9 per cent in the gas phase. Pyrite in concentrate exerts an activating effect, possibly through galvanic interaction with the sphalerite. Metal extractions are dependent on SO2 and O2 tenors of the gas, particle size, and the acidity and zinc content of the solution, but are independent of the ferric ion level. Extractions also reach maxima at about 85°C.Generation of acid may be prevented by conducting the reaction in the presence of ferrous iron and at acidities of 40 g/l or greater. Zinc and iron levels in Elura lead concentrate may be reduced by leaching with SO2/O2.

Jan 1, 1981

By Hannan J. C

In New South Wales, development applications for major coal mining proposals are determined by the Minister for Planning and Environment and applications for mining leases and other mineral titles are dealt with by the Minister for Mineral Resources. The environmental conditions placed on the development consent, the coal mining lease and the approvals and licences under the pollution control legislation, amount to a substantial component of any new project's planning and commissioning considerations.An outline is presented of the framework within which various approvals are granted and conditions for environmental management are imposed upon mining projects. The principles and concerns, as perceived by the regulatory authorities, on which the majority of approval conditions are based are also outlined.No attempt has been made to analyse the extent to which these principles or standards are achieved in practice, nor to discuss the degree to which some of the conditions are achievable with the current status of technology and economics in the coal industry.

Jan 1, 1987

By Sergio N. Monteiro

Wastes generated by our society and the question on how to dispose them is, nowadays, a relevant matter of concern. The objective of the present work was to characterize the technical properties of composites made of discarded jute sackcloth with its coarse wove fabric, serving as reinforcement phase, and polyethylene wastes collected from city dumps, as continuous matrix. Different amounts, up to 30 wt.% of jute plain weave, fabric were press molded at 160°Ctogether with sieved polyethylene particles. The resulting composites displayed mechanical properties that could compete with those of low-density wooden board. Both by presenting a solution to, otherwise, disposed wastes and by helping to prevent deforestation, the investigated composite may be regarded as an environmentally correct material.

Jan 1, 2006

By George K. Burke

Jet grouting was first introduced into North America in the late 1970's, soon after the conception of the system in Japan. However, it was not until the mid-1980's that the technique began to gain acceptance through the renewed interest and efforts of specialist U.S. geotechnical contractors. Since this time, innovations by both American users and other users worldwide have further advanced the technology, with a corresponding increase in the range of practical applications. This paper discusses the evolution of jet grouting in North America, from simple single-fluid methods to more complex triple-fluid methods, to the energy-intensive double-fluid and SuperJet methods. Case histories, illustrating a variety of jet grouting methods and applications, are cited to support the newest United States applications.

Jan 1, 2002

By Richard J. Hartman

Current design practice is to select steel sheet piling sections using sufficient section modulus and yield strength to resist the calculated bending moment. Thus, section modulus is the only property of the sheet pile cross section used in the selection process. Full scale laboratory testing documented that section modulus alone is insufficient to predict the strength of sheet piling. During testing, sheet pile sections with equivalent section modulus exhibited as much as 75 percent difference in load resisting capacity. Analytical study following the testing established that, in addition to the traditional longitudinal (vertical) stress in sheet piling, transverse (horizontal) stresses are also present. Transverse stresses reduce the ability of the sheet piling to function in the intended manner. It was found that transverse stresses result from the pressure applied by soil and water and that the capacity of the sheet piling diminishes with increased pressure. All sheet piling is subject to this behavior. This paper describes the testing and the results and establishes that a problem exists. A two dimensional procedure is described that assists in evaluating transverse stresses and their effect on sheet pile capacity. A method of creating design aids for use by engineers is illustrated.

Jan 1, 2006

By M J. Bourassa

In addition to the geologic risk of a particular project, the criteria that an international exploration company (æIECÆ) utilises when making an investment decision in a particular country should also include a critical analysis of the political, judicial and fiscal regime of the host country. A key investment criteria of an IEC is mineral tenure and the security and continuity of that mineral tenure under the host countryÆs existing legal system as well as the host countryÆs overall legal, political and fiscal framework, the latter of which can affect the projectÆs overall economic viability in a number of ways. The authors, Steve Vaughan and Michael Bourassa of Aird & Berlis, Toronto, Canada, have taken the position that developing an understanding of a countryÆs legal tradition is a crucial first step in analysing the mineral regulatory regime of a particular country. This paper continues their efforts to overview the most recent legal trends affecting the worldÆs mineral industry and attempts to analyse, categorise, compare and contrast differing legal systems, cultural backgrounds and economic philosophies relating to the development of mineral rights in Pacrim countries and the resulting commercial, legal, and political framework which ultimately drives the relevant mineral legislation. For the convenience of organisation of this analysis, the authors have divided the Pacrim countries into four smaller groups, firstly, on the basis of their legal tradition and, secondly, by their geographic location:Common Law Countries: USA, Canada, Australia and New Zealand; Spanish Civil Code Countries: Mexico, Central America (Panama, Nicaragua, El Salvador, Guatemala), South America (Chile, Peru, Ecuador, Colombia). Communist or Former Communist Countries: Mongolia, China, Russia. Countries of the Pacific Southwest: Phillippines, Indonesia, Malaysia, Indo-China (Vietnam, Laos, Cambodia, Thailand), Papua New Guinea. The discussion starts with an analysis of the various types of legal regimes, attempts to classify or categorise them, reiterates the necessity for the rule of law and those factors which encourage mineral exploration and development and discusses and recommends the expansion of a practical country competitiveness rating system developed by the Fraser Institute. In addition to the fundamental issue of mineral tenure û what it is and how secure it is û the paper discusses how different legal systems have shaped different approaches taken by individual nations to attract foreign mineral investment. The paper analyses the best practices and experiences accumulated in different Pacrim countries with varying legal traditions and identifies a practical country competitiveness rating system which the authors believe should be expanded to cover all minerally endowed countries. This rating system will permit countries to identify their mineral regime weaknesses and adjust their legal systems to better attract mineral investment and will also permit exploration and mining companies to compare their jurisdictional choices with those selected by their competitors.

Jan 1, 1999

AUSTRALIA CHAPMAN Gary JOHN WAGSTAFF CONTSRUCTIONS PTY. LTD. 1 Ashgrove Crescent 4060 ASHGROVE BRISBANE HILLAR Jaaes Director J.A. HILLAR & ASSOCIATES 99 Woolwich Road WOOLWICH, NSW 2110 WAGSTAFF John Managing Director JOHN WAGSTAFF CONSTRUCTIONS PTY. LTD. 1 Ashgrove Crescent 4060 ASHGROVE, BRISBANE AUSTRIA FUCHSBERGER M. TECHNISCHE UNIVERSITAT INSTITUT FUR BODENMECHANIK Rechbauerstrasse 12 8010 GRAZ

Jan 1, 1994

By Laura McNally

In 2006 McNally International Inc. in a Joint Venture partnership with Aecon Constructors was the successful bidder on two York Region Tunnel Projects: Bathurst Collector/Langstaff Trunk Sewers; and YDSS Interceptor Sewer 19th Avenue Project. These projects comprise a total of 13 kilometres of 2.74 meter finished diameter tunnels and are both part of the York Durham Sewer System (YDSS). Both contracts require the use of EPB tunnel boring machines with a precast concrete segmental liner. The following provides an overview the two projects.

Jan 1, 2008

By Bill Elverman

Randy and Kenny Robison have visited every coal mine that would let them in the door, to survey the best mining practices. The brothers have spent nearly their entire lives working in coal operations. The Robison’s started out on lube and grease trucks and worked their way up to respected industry leaders in Alabama. The Robisons have owned MS&R since 1989. Since then, they have created a niche for themselves in providing coal for Alabama’s metallurgical coal market. A great deal of the knowledge the Robisons have amassed throughout the years has come from observing — taking note of what works and what does not. In early spring 2004, they commissioned a Komatsu America PC3000 Super Shovel. Outfitted with a backhoe attachment and a 16-m3 (21-cu yd) bucket, MS&R’s PC3000 is currently one of the largest mining excavators working in Alabama.

Jan 1, 2005