Search Documents

By Ke Yang

Drilled shafts are widely adopted as the foundation for sound walls. However, there has been a lack of uniformity in design and analysis methods and design criteria, in terms of factor of safety against ultimate capacity failure as well as the allowable deflection. In order to establish a uniform design methodology for the drilled shafts supporting sound walls in cohesive and cohesionless soils, respectively, a database of full-scale lateral load tests on fully instrumented drilled shafts was collected. Based on the compiled database, existing design methods and design criteria of laterally loaded drilled shafts were evaluated. Broms method and COM624P (or LPILE) are suggested as the design methods for drilled shafts supporting sound walls in both cohesive and cohesionless soils. Additionally, the corresponding design criteria, including factor of safety and permissible deflection, for both design methods are recommended. Two full-scale lateral load tests on fully instrumented drilled shafts were subsequently conducted in Colorado to further verify the design recommendation. A comprehensive geotechnical investigation program was also carried out at the two new lateral load test sites that included pressuremeter test, SPT, as well as laboratory triaxial consolidated undrained tests and direct shear tests on the soil samples taken from the lateral load test sites. The test results obtained at these two load test sites were employed to validate the recommended geotechnical design and geotechnical testing methods for the drilled shafts supporting sound walls.

Jan 1, 2007

By John M. L Lewis, Antoine F. Mulaba-Bafubiandi

In the irradiation of ore particles by microwave energy preferential absorption of this energy occurs in minerals having specific dielectric properties (Bradshaw, 1999). This leads to a selective heating of the various components of within the ore particle matrix. The result is a differential thermal expansion of such components and the resulting induced stresses become ideally concentrated at mineral grain boundaries (Kingman et al., 2000). Dependent upon the relative composition of absorbent, opaque and reflective components this may lead to enhancement of the inter-granular fracture of the ore particles in the initial comminution process (Fandrich et al., 1997). The potential is thus a greater proportion of free mineral grain within the fractured ore particle that may lead to improvement in subsequent mineral separation processes. As the composition of the ore dictates the result of such a treatment (Kingman et al., 2000) it is essential to evaluate the response of each ore sample on an individual basis. This paper reports on results obtained from two ore samples: the one being the zinc ore from the Black Mountain mine (South Africa) and the other a pre-concentrated sample of handpicked cobalt?copper mixed oxide ore from the Gecamines (DRC). The equipment and methods used to simulate the comminution of the samples and evaluate the level of the value liberation will be described along with the results obtained. Using King (1975), Kanellopoulous and Ball (1975), and Gungor and Atalay (1998), a comparison between the behaviour upon microwave irradiation of sulphide and mixed oxide ores leads to conclude that while the technique (i.e. microwave irradiation) is appropriate to the zinc sulphide ore, it does not seem to lead to exceptional results for the oxide.

Jan 1, 2005

By T. H. Chan

As the University of Hong Kong and their advisors planned their new Centennial Campus it became clear that they would have to re-provide existing water reservoirs on an adjacent site with new salt water reservoirs located underground in two new caverns. The existing reservoirs are owned by the Water Supplies Department who provide salt water for sanitary flushing and a separate potable water supply for regular use. Although underground reservoirs had not previously been adopted locally, the planning has been completed to a tight schedule and the construction is well advanced. The need to preserve historic buildings imposed constraints, as did the requirement to minimise potential construction nuisance for the local community and environment. This paper presents the background to the project and the work carried out to develop an innovative, sustainable and environmental acceptable solution. Construction progress to date is also presented.

By Larry Schneider

Are you one of the thousands of hunters, fisherman, or hikers who purchased handheld GPS systems over the past several years and then been disappointed in their accuracy and performance. Or maybe you are one of the hundreds of blasters who have attempted to use GPS as a method for locating the exact position of their blast and measure distances from the blast to nearby structures. If so, you may have found that the accuracy of the handheld GPS systems left much to be desired. It may be time to get the units back out of storage and give them another try. As of midnight, May 1, 2000, the federal government has turned off the “error” built into the system known as “selective availability.” Here is a brief explanation of what that means in a question and answer format.

Jan 1, 2001

By D Craw, D Falconer

The Morning Star mine is one of numerous historically mined gold-quartz lodes in the Preservation Inlet goldfield of southwest Fiordland. The mine is hosted in Early Ordovician metasedimentary rocks that are composed predominantly of psammitic and pelitic lithologies. These rocks still contain their primary depositional features and are characterised by upper greenschist facies metamorphic grade.   The Morning Star mine lies on the eastern limb of a gently south plunging anticline. A bedding parallel fault-vein and an associated network of minor quartz veins hosts mineralisation. The main fault-vein structure strikes N-NW, dips steeply (~60¦) W, has a strike length of ~350 m, a vertical extent of ~170 m and is up to 2 m in thickness. The internal structure of the fault-vein consists of laminated quartz, massive and fibrous quartz, and silicified breccias/cataclasites. Gold is typically coarse grained (~1 - 2 mm) and associated with pyrite, arsenopyrite, chalcopyrite, tetrahedrite and galena. The geometry of the Morning Star mine is similar in form to that of a saddle reef. Gold-quartz lodes in the Preservation Inlet goldfield are comparable in geometry and host rock to their offset equivalents in the Golden Blocks field of NW Nelson.

Jan 1, 2005

By Allan E. Koski

Ceveland-Cliffs uses a specialized software package in mine planning at the Empire Mine, an iron ore mine it manages on Michigan’s Marquette Iron Range. The application puts together years of mining experience that began in the early 1960s on the eastern end of the Marquette Range. The Empire Mine is in its 38th year of production. It uses the software to model a complex and highly variable low-grade magnetite ore body, capturing the economics of mining and processing to the final product. With special attention given to geostatistical methods, the software is used for all geologic modeling, ore reserve estimation, ore control, pit design and short- and long-range planning.

Jan 1, 2000

The mineralogy of nickel slags from the flash smelter of Western Mining Corporation Ltd. at Kalgoorlie was studied. Residual magnesium silicates in the sulphide concentrates raise the melting point of the slag and result in the formation of magnesium-rich olivines. Addition of lime lowered the melting point, and, in slowly cooled slags, resulted in the formation of a pyroxene.Magnetite and sulphides were also present in all slags.The converter slags contained an olivine near fayalite in composition, together with wiistite, magnetite, and a little sulphide.Accretions from the hearth of the flash furnace were largely composed of magnetite with subsidiary olivine similar in composition to those of the flash furnace slags.Wall deposits, however, were largely composed of nickel ferrite and nickel-iron olivines.

Jan 1, 1976

By A. McLean, M. Iwase, K. Wakimoto, K. Katogi, Y. Kikuchi

One of the greatest obstacles to the application of physical chemistry principles to the elucidation of slag-metal reactions is a lack of knowledge of activities of the reacting species. To a large extent, oxygen potential of the slag phase governs iron and steelmaking practice. Without oxygen control by means of appropriate sensors, the behaviour of the other elements cannot be managed. In this paper, measurements of the FeO activity with various types of electrochemical FeO sensors will be described together with examples of their applications for improved strategies toward better practice for ladle metallurgy and sulphur and manganese distributions between slag and metal phases during steelmaking. Measurements of FeO activity have also been made in order to improve dephosphorization reactions. This type of work has led to significant reduction in volume of slag generated within the steelmaking vessel, which in turn has important implications for refractory wear, metal yield, alloy recovery and improved productivity. Finally, an on-line sensor is described that permits the oxygen potential to be determined for both the metal phase and the slag phase during steelmaking in the BOF.

Jan 1, 2004

An understanding of the origin of mineral deposits and their relationship to local and global geotectonics is essential if regional targets for mineral exploration are to be chosen. Volcanism, metamorphism and tectonism are especially significant for the origin and emplacement of mineral deposits, which, far from being fortuitous oddities of nature, occupy well defined positions within distinctive lithofacies. Thus, suggestions for mineral exploration targets can be made taking into consideration the position of 'fossil' convergent and divergent plate tectonic boundaries to indicate areas of specific types of mineralisation. To be borne in mind, though, that level of exposure, time and location of magma generation are all additional and important controlling factors. To further understand the importance of the above parameters, one must refer to the concept of paired metamorphic belts (Miyashiro 1973) which develop during an orognic cycle. These belts are generally constructed in such a way that an ophiolite type complex with metamorphic grades related to high pressure and moderate temperature regimes is flanked by an area of calc-alkaline volcanism and granitic activity with metamorphic grades within a region of high temperature and low pressure. The former situation is usually the seat of primary magmatic mineralisation, whereas the latter contains base metal. Deposits of acid plutonic and volcanic association. As will be seen later, this particular metamorphic-volcano-orogenic situation is well developed in some parts of New Zealand. For the present purpose a distribution of potential ores as related to plate tectonic processes is given below:a) Divergent plate boundaries: primary magmatic Ni-Cu, Pt,Cr, PeS2 and Cu, Pb,Zn in hot brines-hydrothermal environments Mn deposits.b) Convergent plate boundaries: stratabound Cu-Fb-Zn-Ag of felsic volcanogenic association. Porphyry eu-Au of island arc type, porphyry Cu-Mo of continental type. Cu, Au, Y, Sn, Hg, Sb of vein type and replacement lode related to granitic activity.c) Au of hydrothermal vein association, related to late dynamo-metamorphic events. By virtue of ocean floor spreading, regions of divergent plate boundaries are eventually juxtaposed or welded n to areas where plate collisions occur. This is then followed by partial melting due to various causes, just above the descending plate; thus creating a zone of acid to intermediate magmatism. The final picture is that of an orogenic zone with the paired metamorphic belts outlined above.

Jan 1, 1976

By G Chitombo, D Francis, P C. Stewart, I Brunton

The ability to precondition (weaken) a rock mass to enhance caving (cavability and fragmentation) is becoming increasingly important, as more potential caving deposits are in stronger rock masses, and at greater depth. This paper discusses a full-scale blast preconditioning experiment conducted at the Cadia East mining operation, including quantification of visible and microscale blast damage. From a cave mining perspective, the objectives of the experiment were to quantify the effect of confined blasting on rock mass characteristics relevant to enhanced caving, and to provide calibration data for the purpose of numerically modelling alternative blast preconditioning designs.The experiment was located approximately 360 m below surface, and consisted of two f165 mm blastholes (60 m vertical holes) and eight HQ diamond drill monitoring holes (35 m horizontal holes). The diamond drill holes were used to sample the rock mass before and after the blast at varying distances from the blastholes. Rock mass blast damage was quantified both visually using core logging, and on a microscale using LABYRINTH® statistical analysis of X-ray microtomography data. Results from the experiment indicated four major findings:on the visible scale, the experiment indicated a 147 per cent increase in the number of hairline cracks within 5 m (p value = 0.015), but no change in geotechnical logging parametersmicroscale tomography of intact rock samples indicate significant localised intact rock damage up to 4 m from the blasthole (p = 0.007)preliminary point load test results indicate that blast damage results in a significant reduction in intact rock strength (p = 0.050)the significant increase in porosity and microfracture size associated with damage provides a mechanism for reduced intact rock strength due to confined blasting.CITATION:Stewart, P C, Brunton, I, Francis, D and Chitombo, G, 2016. Quantification of rock mass damage associated with a confined blast preconditioning experiment at the Cadia East block cave, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 119–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Disseminated gold mineralization in the Vunda River area 12 km SE of Lautoka in Viti Levu occurs sporadically in shoshonite volcanics within an alteration area of some 6 km2. No definite intrusions have yet been located though possible intrusions occur toward the centre and on the eastern margin of the area. The nature and distribution of alteration suggests the presence of a co-magmatic mineralizing stock just below the surface.The gold occurs within close spaced fractures and occasionally around the c1asts of breccia and agglomerate.Various types of alteration compatible with porphyry mineralization occur, but to date show no zoning or defined correlation with incidence of gold which occurs in various alteration facies.It is suggested that the gold and trace copper mineralization at Vunda arises from the sub-volcanic intrusive phase (monzonite) of the Sambeto shoshonite (5 m.y.) and is part of an E-W zone of porphyry-type mineralizationtrending easterly to the Kingston porphyry copper deposit at Navilawa.There is a close similarity between the Vunda mineralization and some of the porphyry deposits of alkali affinity in British Columbia, Canada.

Jan 1, 1978

By Jack Eloranta

The winning of metals often requires fine grinding of very hard ore. The US Bureau of mines measured compressive strengths exceeding 100,000 PSI (700 MPa) in Minnesota taconites. Grinding down to 300 mesh (50 µ) is required for some fine-grained taconites. While other metal ores may not be as strong, significant grinding costs are the rule rather than the exception. One author recently reported that a 7% drop in grinding costs would fully offset a doubling of the drill and blast budget. Another author found that drill and blast costs were 13% of the costs of producing iron ore concentrate while fine crushing and grinding were over 60% of the cost of producing concentrate.

Jan 1, 2013

The theme of this conference is æRediscover OtagoÆ and the conference occurs during a resurgence of economic activity in New Zealand, and in particular at a time when the Macraes Gold Project has had a significant effect on mining and business activity in Otago. The Macraes Gold Mine has implemented a Zero Accident Programme and this paper reviews some of the factors responsible for the implementation.

Jan 1, 1992

By Filip Rochette, Yvan De Busscher

Extraction of minerals can be achieved by a variety of technologies; one of them is ion exchange. There are several ion exchange configurations and mechanical set-ups available, but only one technology will provide more process performance and flexibility compared to the other. The multiple column Continuous Countercurrent Ion Exchange (CCIX) technology provides the highest form of process flexibility with also the highest mineral recovery feasible through ion exchange. In comparison with a fixed bed system, the PuriTech CCIX system offers the benefits of continuous counter-current contact mode. This way the resin capacity is fully exploited leading to reduction in resin inventory and, at the same time, in chemicals and water consumption, and product dilution. For any set of operating conditions the mass transfer zone has a characteristic length (MTZL). The MTZL can be expressed in duration, column length, or volume, but is the measure of the quantity of resin in the system that is doing "work" at any given moment in the process. The objective of continuous ion exchange processing is to eliminate all resin volume from the process equipment that is not within a mass transfer zone. In most commercial ion exchange processes for the recovery of metals, CCIX engineering can eliminate as much as 20 - 80 % of the ion exchange resin inventory. Consumptions of water and chemicals are typically brought down around 40% or more. For each type of resin the selectivity/affinity towards a particular metal depends on the basic process conditions such as pH, concentrations of other competing metals in solution. By changing the pH in the ion exchange process phase, the selectivity of the resin can be changed. By doing this, a split elution, or extraction of metals separately can be achieved and the effect of other competing metals (cross-contamination) can be reduced. For example the DOW resin XUS43578 is commonly used for the recovery of copper or nickel/cobalt separation.

Jan 1, 2016

By P. Mbele

Iron ore concentrate is not easily transported to, or processed in, ironmaking plants, therefore it is necessary to agglomerate. This paper will determine the possibility of agglomerating Sishen concentrate into suitable ironmaking feedstock. Pelletizing is one of the conventional and preferred agglomeration processes for iron ore concentrate investigated at Kumba Value-In-Use Laboratories. Sishen concentrate was mixed with binder, and then pelletized using a laboratory pelletizing disc; afterwards the green pellets were indurated at high temperatures to give strength high enough to survive handling and lessen disintegration in the shaft during ironmaking. Sishen pellets have satisfactory physical and metallurgical properties which make them suitable feedstock for the direct reduction processes. These were tested under Midrex shaft operational conditions and performed well, with a metallization of 94.47% being attained.

Jan 1, 2012

By R. J. Schafer-Frentz, T. G. Joseph, M. Curley

"Greenhouse gas emissions—specifically of carbon dioxide—are a concern in Canada, where industrial sectors such as mining are stringently regulated for carbon release. Cumulative emissions are positively related to fuel consumption, which is controlled by several factors. This study investigates one of these factors: the product of vehicle speed and running surface total resistance (TR; sum of rolling resistance and grade resistance). Results show that TR directly affects fuel consumption and emissions—a relationship that is mathematically predictable. Fuel consumption and emissions, which are principally associated with the durability or deterioration of wearing course materials, were analyzed to aid selection of road construction capping material of low rolling resistance. In the oil sands region in the province of Alberta, ground conditions change seasonally. Therefore, the annual fuel consumption for the same wearing course material was also compared. Results demonstrated that haul truck size was a contributing factor, but vehicle speed and TR more strongly influenced fuel consumption and emissions. ¦ KEYWORDS Carbon dioxide, Emissions, Fuel consumption, Grade resistance (GR), Greenhouse gas (GHG), Haul truck, Rolling resistance (RR), Total resistance (TR) RÉSUMÉ Les émissions de gaz à effet de serre (GES), et particulièrement celles de dioxyde de carbone, sont un problème au Canada, où les secteurs industriels tels que l’exploitation minière sont rigoureusement réglementés pour leurs émissions de carbone. Les émissions cumulées sont indéniablement en lien avec la consommation de carburant, qui est contrôlée par plusieurs facteurs. Cette étude examine l’un de ces facteurs, à savoir le produit de la vitesse du véhicule et de la résistance totale de la surface de roulement (la résistance totale, ou RT, est la somme de la résistance au roulement et de la résistance due aux rampes). Les résultats montrent que la RT affecte directement la consommation de carburant et les émissions, un lien qui est mathématiquement prévisible. La consommation de carburant et les émissions, qui sont principalement associées à la durabilité ou la détérioration des matériaux composant la couche d’usure, ont été analysées afin de contribuer à la sélection de matériau de recouvrement pour la construction de routes ayant une faible résistance au roulement. Dans la région des sables bitumineux de l’Alberta, les conditions au niveau du sol changent à chaque saison. Ainsi, la consommation annuelle de carburant pour le même matériau composant la couche d’usure a aussi été comparée. Les résultats ont montré que, si la taille des camions de transport est un facteur déterminant, la vitesse des véhicules et la RT influencent davantage la consommation de carburant et les émissions. ¦ MOTS CLÉS camion de transport, consommation de carburant, dioxyde de carbone, émissions, gaz à effet de serre (GES), résistance au roulement, résistance due aux rampes, résistante totale (RT)INTRODUCTION In Canada and around the world, global climate change has become a topic of great concern and discussion. Pres-sure on world leaders to quickly reduce their carbon footprint is prevalent, prompting new standards and regulations in various industries, including mining and oil and gas. In 2017, the Government of Alberta implemented a carbon tax. The majority of mining activities in this province are truck-shovel operations, where a large fleet of ultra-class trucks is loaded by shovels. Ultra-class haul trucks, classified as those with a capacity of 218–363 tonnes (t), emit high levels of carbon as they travel to processing entry points and waste dumps as designated by the mine plan and mine dispatcher. Mined ore and waste is typically moved over two 12-hour shifts per day throughout the year."

Jan 1, 2019

By Kray Luxbacher, Mario Karfakis, Erik Westman, Peter Swanson

Three-dimensional velocity tomograms were generated to image the stress redistribution around an underground coal longwall panel to produce a better understanding of the mechanisms that lead to ground failure, especially rockbursts. Mining-induced microseismic events provided passive sources for the three-dimensional velocity tomography. Surface-mounted geophones monitored microseismic activity for 18 days. Eighteen tomograms were generated and high-velocity regions correlated with high abutment stresses predicted by numerical modeling. Additionally, the high-velocity regions were observed to redistribute as the longwall face retreated, indicating that velocity tomography may be an appropriate technology for monitoring stress redistribution in underground mines.

By D Caley

During the response to the Moura No 4 disaster, use was made of the New South Wales Mines Rescue Service’s ‘Mineshield’ inertisation equipment. The equipment had to be transported from Newcastle, approximately 1400 kms, and the liquid nitrogen a similar distance. The time taken, and therefore availability of the liquid nitrogen, became a significant problem. Operational issues were also experienced during use. Typically the liquid nitrogen is converted to a gas (vaporised) before being injected into the mine. However, as the propane gas tanker used for the vapourising unit was delayed, an attempt was made to inject the liquid nitrogen directly down uncased boreholes. This proved unsuccessful.Following the Moura No 4 disaster and the Moura No 2 disaster, recommendations were made relating to having inertisation capacity for the Queensland coal mining industry. Today the Queensland industry has multiple options available for inertisation, including the high-volume GAG and smaller volume units such as boilers and membrane separation units. Although it ultimately aided re-entry into Moura No 4, most likely due to the issues associated with supply to Central Queensland, liquid nitrogen has not found favour within the Queensland industry as an inertisation tool.Coregas has commissioned an air separation plant in Mackay, improving the availability of liquid nitrogen to Central Queensland. Based on the availability of this nitrogen, recent sealing operations at Kestrel have trialled using liquid nitrogen and associated vapourising units. This paper details the practical application and findings of using liquid nitrogen during routine longwall panel sealing.CITATION:Caley, D, 2017. Using liquid nitrogen for the inertisation of goafs, in Proceedings Australian Mine Vent Conference 2017, pp 35–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Donald A. Bruce

The construction of major structures in karstic limestone terrains poses difficult problems to designer and contractor alike. This reflects the inherent variability of such conditions, and also the significant impacts caused by the construction processes themselves. Three case histories are provided of recent projects in the United States: the sealing of a major inflow into a quarry, the improvement of a highly loaded bridge pier foundation, and the installation of high capacity micropiles. Emphasis is placed on problem assessment and execution verification.

Jan 1, 2002

By D. Oyler

The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia collaborated in an intensive study of ground behavior, reinforcement performance, and stress redistribution at the Emerald Mine in Southwestern Pennsylvania. The study site was a longwall tailgate subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8m (16 ft) above the entry. A computer simulation of the field site was conducted using FLAC-2D, incorporating a broad range of rock behaviors and failure mechanisms. Comparison between the measurements and the simulation showed that the model was able to capture the most significant aspects of the roof and support system behavior, particularly, the extensive slip along bedding that created a partially destressed "softened" zone in the immediate roof. The model also showed that supplementing the normal roof bolt support pattern with cable bolts would allow the entry to survive a further 20-25% increase in the applied horizontal stress. Such information could have very practical application to the design of roof support systems for coal mines.