Search Documents

By E. V. Deshayes, W. E. Young

"INTRODUCTION The Camp Bird mine was investigated by Bureau of Mines engineers 3/ September 22 and 24, 1942, and April 29 and 30, 1944. In a subsequent report and supplement, it was recommended that core drilling be done below the 14th. level to determine if commercial ore existed at greater depths, and particularly if ore existed in the vein or adjacent thereto where it passes into the sedimentary formations estimated to underlie the volcanics approximately 400 feet below the 14th level.Seven diamond-drill holes aggregating 3,956 feet were drilled. Four of these holes were under the Hematite ore body and three were under the Big Discovery ore body. Two holes under, the Hematite ore body wore directed at angles but little steeper than the angle of dip of the vein and penetrated the sedimentaries beneath the volcanics close to the vein. Enough low-grade ore was found at the base of the Telluride conglomerate to indicate the presence of a large body of low-grade zinc sulfide ore. Two holes were directed to crosscut the vein at a depth of approximately 125 feet below the 14th level. No commercial ore was cut, but the vein showed the average width and same general characteristics as at the 14th level. One hole under the Big Discovery ore body was directed to crosscut the vein and test the base of the Telluride conglomerate in the footwall block. No commercial ore was found in either the vein or the sedimentary horizon. One hole was directed to test the base of the Telluride conglomerate in close proximity to the vein in the hanging-wall block. This hole was lost approximately 100 feet short of its objective, and a third hole was drilled to accomplish this same thing. The third hole was stopped approximately 50 feet short of its objective when failure of equipment caused a recess of the"

May 1, 1948

By María Quintana, Valerio Yachachin, Juan Rodríguez

Con el interés de evitar un inadecuado descarte de lámparas fluorescentes y favorecer su reciclaje y aprovechamiento, en este estudio técnico se analizó el contenido de tierras raras (REE, por sus siglas en inglés) presente en varias marcas de lámparas. Caracterizado el polvo fluorescente, se procedió a usar la lixiviación ácida multietapas como método de trabajo para el reciclaje, obteniendo como resultado relevante la extracción del itrio en su totalidad.

Aug 30, 2020

By J. P. Harrison, J. A. Hudson

ABSTRACT: Given the current widespread use of numerical models for rock mechanics and rock engineering, and the ‘Technology Road Map’ theme of the Congress, it is timely to consider the key issues in matching numerical models to rock engineering problems. The three main aspects are: a) identifying the mechanisms, variables and parameters that are relevant to a particular rock engineering project; b) establishing the content and mode of operation of a particular code; and c) deciding whether a particular code provides an adequate model for a particular project. We summarise the key issues, highlighting the concept of rock mass domains, validation and the ability to present the results of a modelling exercise. We include three compact numerical modelling case examples to illustrate the points. Finally, we also present a ‘roadmap’ to assist in the process of matching a numerical model to the rock reality. RESUME: Considérant l’utilisation généralisée des modèles numériques en mécanique des roches et en ingénierie au rocher ainsi que le thème du congrès ‘technology road map’, il est opportun d’aborder les problèmes essentiels liés au choix des modèles numériques dans les problèmes ingénierie au rocher. Les trois aspects principaux sont : a) l’identification des mécanismes, variables et paramètres appropriés au projet considéré, b) la définition du contenu et du mode de fonctionnement d’un code numérique donné, et c) la possibilité de décider si un code donné fourni un modèle approprié au projet considéré. Les points clés sont résumés en mettant en évidence les notions de “massif rocheux”, de validation et de capacité à présenter les résultats d’une approche numérique. Nous présentons trois brèves études de cas qui illustrent ces points. Enfin, nous proposons aussi un logigramme pour aider au choix d’un modèle numérique approprié pour représenter la réalité d’un problème au rocher. ZUSAMMENFASSUNG: Im Licht der augenblicklich weitverbreiteten Nutzung von numerischen Modellen in der Felsmechanik and im Felsingenieurbau und unter Beruecksichtigung der Themenstellung des Congresses “Technology Road Map”, erscheint es an der Zeit die Kernprobleme, die sich mit Fragen der Abstimmung der numerischen Modele mit Hinblick auf ihre Anwendbarkeit im Felsingenieurbau beschaeftigen, naeher zu befassen. Die drei wesentlichen Aspekte sind: a) Identifizierung der Mechanismen, Variablen und Parameter, die fuer ein bestimmtes Projekt im Felsingenieurbau von Bedeutung sind; b) die Festlegung des Inhalts und des Modus Operandi eines bestimmten Codes, und c) die Entscheidung darueber ob ein bestimmter Code ein hinreichendes Model fuer ein bestimmtes Projekt ergibt. Wir fassen die wichtigsten Punkte zusammen, heben dabei das Concept der Gesteinsmassen Domaenen (Rock mass domains) hervor, und erarbeiten ihre Beurteilung und die Moeglichkeit diese zu praesentieren in den Ergebnissen einer Model Uebung. Wir schliessen drei Beispiele von numerischen Modellen ein in denen diese Punkte erlauetert werden. Zuletzt schlagen wir eine “Roadmap” vor, um dem Prozess der Abstimmung des numerischen Modells mit der “Felsmechanischen Wirklichkeit” zu unterstuetzen.

Jan 1, 2003

By J. C. Edwards

The National Institute for Occupational Safety and Health (NIOSH) implemented a real-time neural network system which can discriminate mine fires from nuisance diesel emissions as part of an atmospheric mine monitoring system in NIOSH?s Safety Research Coal Mine. The real-time response of a neural network to fire sensor outputs was demonstrated for coal and belt combustion in the presence of diesel emissions. The fire sensors consisted of an optical path smoke sensor, a carbon monoxide (CO) sensor, and two types of metal oxide semiconductor (MOS) sensors. The real time neural network was trained with coal, wood, and belt fire experiments with and without diesel emissions background. The trained neural network successfully predicted mine fires with these combustibles in the smoldering stage prior to the onset of flames.

Jan 1, 2005

By K. Aoki, Y. Mito, S. Shirasagi

The authors developed the TBM Excavation Control System (the TBM Navigator), in order to realize the advanced observational construction. During the excavation using this system, the rock strength value is immediately calculated from the TBM driving data as an index of rock properties, and the drill energy coefficient is also calculated from the drill logging data that is carried out using the probe hole ahead of the tunnel face. In this study, a new, geostatistical simulation-based method is proposed for the automatic prediction of the rock properties ahead of the tunnel face with good precision, using both the drill logging data and the TBM driving data. The applicability of this method is validated through the prediction at the actual tunnel excavation that passes through the faults. Les auteurs ont mis au point un Système de Contrôle de forage avec la machine à pleine section (Navigateur de la machine à pleine section), en vue de réaliser un système de surveillance plus efficace. Avec ce système, la résistance de la roche est immédiatement calculée, au cours du forage, à partir des données de conduite de la machine, comme indice des propriétés de la roche, et le coefficient d'énergie de la foreuse est également calculé à partir des données de log de forage collectées dans un trou de sonde foré dans le front de taille. Dans cette étude, on propose une nouvelle méthode basée sur la simulation géostatistique qui permet de prévoir d’une manière automatique, des propriétés de roches se trouvant derrière le front de taille avec une précision satisfaisante, à l’aide des données de log de forage et celles de conduite de la machine à pleine section. Cette méthode s’est avérée suffisamment précise au cours du forage d’un tunnel réel qui traversait une zone de failles. Die Autoren entwickelten das TBM Ausschachtungssteuerungssystem (den TBM Navigator), um noch besser überwachte Bauarbeiten zu ermöglichen. Unter Einsatz dieses Systems wird die Gesteinsfestigkeit während der Ausschachtungsarbeiten unmittelbar aus den TBM Antriebsdaten als ein Index für die Gesteinseigenschaften berechnet. Gleichzeitig wird auch der Bohrenergiekoeffizient aus den Bohrlogdaten berechnet, die an Hand der Probebohrung am Stirnende des Tunnels erhalten wurden. In der vorliegenden Studie wurde ein neuartiges, auf geostatistischen Methoden basierendes Verfahren für die automatische und angemessen genaue Vorhersage der Gesteinseigenschaften am Stirnende des Tunnels vorgeschlagen, für das sowohl die Bohrlogdaten als auch die TBM Antriebsdaten verwendet werden. Die Anwendbarkeit dieser Methode wird durch die Vorhersage bei einer tatsächlichen, durch Verwerfungen verlaufenden Tunnelausschachtung bewiesen.

Jan 1, 2003

Membrane technology has been available for over 36 years, but has been used sparingly in the general mining industry. However, recent developments in polymer chemistry, spiral wound element construction, pretreatment equipment and techniques and an expanded understanding of membrane fouling and cleaning techniques have dramatically improved the reliability and robustness of membrane based systems in the mining industry. Harrison Western has expanded the use of this “new” technology to enhance the use of membrane technologies to separate metals from large volume heap leach mining solutions containing copper, zinc, and iron, gold or silver. Moreover, membrane technologies are ideally suited to fractionations that add value to processing fluids from refineries like separating metals from acids or concentrating acids and producing high quality process fluids. Finally, wastewater from Acid Mine Drainage (AMD) or, as in the case of the Newmont Yanacocha Mine in Peru, the treatment of excess barren leach solution created during the rainy season, can be cost effectively processed to meet World Bank Standards for surface discharge. Polymeric membranes, specifically thin-film composites, have been developed that will purify, fractionate or concentrate gold, silver, copper, zinc or nickel. Recent applications have been developed for spiral wound modules that operate across the pH spectrum from 0 to 14. Systems using membranes have been constructed that operate on feed streams from 140° C to 300 centipoise. Opportunities exist to apply membrane technology to concentrate gold, silver, copper, zinc or nickel using thin film composite membranes. Engineered membrane types can operate across the spectrum from low pH (<2) acid applications to high pH > 10 cyanide applications. Incorporating HW EMS™ membrane technologies into current mining operations could allow one to increase production because the membrane technology would be used to pre-concentrate heap leach solutions, and therefore, increase utilization of existing extraction and refinery capabilities.

Jan 1, 2007

By Ann G. Kim

Studies on the initiation and propagation of mine fires have dealt almost exclusively with coal. It has been assumed that the self-heating potential of carbonaceous shales and coal wastes is relatively low. However, in abandoned coal mines and waste banks, initiation and propagation of fires may be strongly dependent on the self-heating tendency of these materials. The purpose of this study was to compare the self-heating probability of carbonaceous shales and coal wastes to that of coals. This study utilized a modified differential thermal analysis method, in which the combustion furnace temperature was the reference to which the sample temperature was compared. Based on the distribution of the maximum temperature differential and the sample heating rate, a self-heating probability value (SHPV) was calculated that corresponded to observed self-heating behavior. In this study, several of the carbonaceous shales and one coal waste had relatively high SHPV. The SHPV did not correspond directly to heating values or to differences in sulfur concentration.

Jan 1, 2010

By Louise H. Michaud

Albian Sands Energy is scheduled to begin production at its oilsands operations in the fall of 2002. Start-up includes the selection and implementation of over 75 IT systems or computer applications. These include engineering applications, systems required to control mining activities, maintenance, the processing plant and utilities, and also systems required to run the company, such as human resources, finances and inventory/warehousing. This paper outlines the processes used for the selection, implementation and integration of these systems in order to optimize the use of information and to meet the technical, business and IT requirements of the company. The first step in Albian?s approach to identifying system requirements is the development of a Business Activity Model, outlining all tasks involved in running the operations. The computer applications required to accomplish each task are then identified by having the IT team work closely with each technical and business unit. Historically, at some companies, the selection of systems has been lead by the IT team or by consultants, with little input from the technical or business units. Typically, this results in products that don?t meet the company?s expectations. To ensure a more positive outcome, Albian believes that it is imperative that the company?s technical and business people are closely involved in the selection process. Integration of the IT systems is also key, including linking all applications through a Data Warehouse and EDMS. Over 120 required integrations have been identified. This ensures the storage of all data in only one location, data security, and easy data and document retrieval for all requirements throughout the company.

May 1, 2002

By S. Auger, S. McDonald, K. Ward

"This preliminary paper provides a summary of lab and mill flotation investigations into the copper collector at two Canadian operations. The orebodies illustrated in these studies both contain mainly copper and zinc with uneconomic quantities of lead. Silver is also present as a secondary precious metal.Each mill has advanced to the extended mill trial stage with Uniflot SP129 as the sole copper collector. The preliminary metallurgical results have indicated higher copper circuit zinc and lead rejection is possible as shown in Case Study #2. In Case Study #1, improved zinc circuit metallurgy has been realized during all the Uniflot copper circuit collector trials. A slight increase in silver recovery has also been observed in the extended trials at both operations. INTRODUCTIONThe Canadian base metal industry is presently going through a rationalization period in response to low metal prices and low grade ore bodies. The response from flotation mills has been to reduce costs by incorporating new technologies such as energy efficient large cells, low moisture pressure filters and low steel consumption SAG mills. Other optimization strategies have been incorporated to get better metallurgical performance such as improved process control and monitoring techniques.The newer flotation plants have embraced many of the latest equipment innovations but they continue to incorporate off-the shelf reagents like xanthate and methylisobutylcarbinol (MIBC) . New collector chemistries have been mostly unsuccessful. Our approach incorporates the best of the old and new chemistry into proprietary formulations that match the application. We have found most single chemical formulations cannot meet the demands of the optimized modern flotation plant."

Jan 1, 1992

By J. R. Stone, J. T. Roy

ASARC09s continuous tapper for lead blast furnace is described. Its use throughout the company&apos;s plants has resulted in higher production rates, lower labor costs, and better working conditions. It has also permitted wide latitude in blast pressures, as well as in charge and slag compositions. The practice of tapping a lead blast furnace has remained essentially unchanged for many years. In principle, it is a batch operation discharging the products from the continuous smelting of lead-bearing materials. As such, it imposes certain restrictions on the proper functioning of the smelting operation. First, it calls for a highly developed sense of timing, and a considerable amount of physical effort on the part of the operator. Dirty and hot working conditions, as well as the hazards of flying metal and slag, usually prevail. These conditions have resulted in higher labor costs, both in rate and in amount. Labor turnover has also been high. Secondly, rigid control of mechanical and metallurgical factors must be maintained. Frequent oxygen lancing of the tap hole is needed to permit tapping, thereby increasing operating costs. Rapid increases in smelting rate, plugged tap holes, or forgetfulness on the part of the operator may permit the molten material to rise above the tuyeies and freeze the furnace. Also, the operator will often blow out the tap hole after draining, filling the area with fume. Composition of charge also vitally affects the tapping. The type of lead-bearing material being smelted will naturally affect the smelting rate, and thus the frequency of tapping. The amounts and types of fluxing materials, which determine the ultimate fluidity of the slag, must be regidly controlled. Finally, the batch tapping of a continuous smelting operation of this type appears to be wrong in principle. The molten material drains into the crucible at the bottom of the furnace where it starts cooling immediately and continues to cool until tapped out. While keeping the lead molten is no particular problem, maintaining a fluid slag at all times is often difficult, and sometimes impossible. These factors all point to the desirability of a method for the continuous tapping of a lead blast furnace. The expected advantages would be more desirable working conditions, lower labor costs, increased production, and a much wider latitude in both blast pressure and charge composition. CONTINUOUS TAPPING Historical. A number of devices, e.g., mechanical tappers, siphons, and lead wells, have been tried in the past in attempting to effect continuous tapping. None proved to be entirely satisfactory for tapping lead and slag simultaneously. It was not until 1955, however, that ASARCO designed and put into operation a successful tapping unit at its East Helena, Mont. lead smelter. This unit is described in detail in U.S. Patent NO. 2,890,951. Continuous Tapping Unit—See Figs. 1 and 2. Fig. 1 is a schematic drawing of the unit in place, showing front and side views. The component parts are identified in the caption. Fig. 2 is an actual photograph, front view, of the tapping unit attached to the base of the blast furnace. Operation. The operation of the tapping unit is quite simple. Essentially it consists of a narrow tapping bay surrounding the furnace tap hole, with a deep notch in the front wall. When the blast furnace is started this notch is open down to the level of the tap hole. Starting the furnace may be accomplished in several ways but the most satisfactory method is to plug the tap hole with clay, permitting metal and slag to build up inside the furnace. Before the liquid reaches the tuyeres, the plug is removed and the furnace is drained to the settler. The blast is then stopped momentarily while the notch in the front wall of the tapping bay is dammed with chrome brick and plastic chrome ore. The blast is again started, and the height of the dam is adjusted so that the liquid in the bay will counterbalance the internal pressure of the furnace. When the desired level is reached the slag and metal will overflow to the settler. It should be noted that the molten material ,is not siphoned from the furnace and that the metal &apos;acts as a liquid valve controlling the flow of slag through the tap hole. During normal operations the tapping bay is filled primarily with lead, covered with a thin layer of slag. Thus, the heavier lead plays the major role in compensating for variations in furnace pressures. Due to the high specific gravity of lead, changes in the liquid level in the tapping bay will never exceed a few inches. For this reason it is seldom necessary to change the height of the dam due to minor variations in operating conditions. Some turbulence of the liquid in the bay is essential at all times. This indicates that the level of the

Jan 1, 1963

By Jeffrey M. Listak

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner&apos;s cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutter head, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head&apos;s effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner improved air quality at both locations to varying degrees in some cases and not in others when compared to a continuous miner with a standard spray system.

Jan 1, 2010

By J. F. Papp

In the United States, chromium has been consumed in three major markets: chemical, metallurgical, and refractory. The predominant end use for chromium in the United States is in the metallurgical market as an alloying element in the production of stainless steel. In addition to being a major stainless steel-producing country, the United States is a major world producer of chromium-containing chemicals and has used substantial amounts of chromite ore for refractory applications. Chromium use is not easily further subdivided within the chemical and refractory industries because there is insufficient publicly available information to do so; however, chromium use can be subdivided among metallurgical industry uses based on the American Iron and Steel Institute (AISI) reported shipments of stainless steel by market classification (agricultural, aircraft, automotive, etc.). It is the goal of this study to determine the distribution of U.S. chromium apparent consumption among major markets in the United States. The distribution is expressed in the form of dimensionless fractions that are computed based on documented chromium consumption by major market. The distribution of chromium among markets within the metallurgical market is computed in a similar manner. Distribution factors are first computed for the major markets, then for markets that are subdivisions of the metallurgical market. The distribution of chromium among major markets has changed substantially over the time period of analysis. The fraction of chromium consumed by the metallurgical market has increased while that of the chemical and refractory markets has declined. Within the metallurgical market, the service industry market accounts for the greatest fraction of chromium consumption followed by transportation. Electrical, machinery, and fabricated products markets account for a substantial share of the metallurgical chromium consumption.

Jan 1, 2004

By H. William Zeller

The U.S. Bureau of Mines evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pet., depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine&apos;s combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O2, but it increased CO2 and NOx, The increase in NOx, of about 12 pet, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 2010

By Jose L. Garcia

The following document aims to cover all issues concerning the three main methods employed for the in-situ survey of concrete pile integrity. Within it are described both sonic coring and low-strain tests and the frequency and time domain analysis of their results, which are the most advanced techniques currently in use in Spain. The survey techniques described were developed and began worldwide deployment in the 1960s, but it was not until the 1980s that they saw large scale implementation in Spain, largely thanks to the miniaturisation of electronics and computer equipment that made them easier to use on-site. Sonic coring, echo and frequency-response testing or mechanical impedance tests are spreading further every day. However, there appears to be a need for standardisation of the testing methods, as well as their implementation, interpretation and the presentation of results. The goal of these Spanish recommendations is to serve as a guideline for test standards and to provide examples for a correct and commonly agreed interpretation of test results, as well as settling any differences in the evaluation of defects detected in foundation works.

Jan 1, 2006

By William O. Vanderburg

This paper 3/gives the results of a reconnaissance of mining districts in Clark County, Nev., made from November 18 to December 22, 1936, and from February 9 to March 8, 1937-in all, 63 days. While the field work Was being done, virtually all of the mining districts in the county were visited and many data on active and inactive properties were obtained. The report covers the locations of the various mining districts, the nature of the deposits, information on past operations, current activity, and general data likely to be useful to operators, investors, and others interested in mining. The geology of the deposits is discussed only briefly. The principal metal-mining districts in the county are Goodsprings, Eldorado, and Searchlight. The zinc-lead ores of Goodsprings have been the most important economically, followed by the gold-silver ores of Eldorado and Searchlight. In the industrial-mineral field, gypsum, limestone, silica sand, and borates are the principal products. Metal mining in the county is characterized by numerous small operations and the ores are either milled locally or shipped to distant smelters.

Jan 1, 1937

[Separates of all the Technical Publications published in 1930 are available at Institute headquarters. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found in the Transactions.] Metal Mining Technical Publi- Title Author Meeting Tran~. cation Volume No. and Page* 264-A.29 Quicksilver Industry in 1929. Im- L. H. Duschak San Francisco T30, 283, 319 provements in the Metallurgy of C. G. Maier and Oct., 1929 Quicksilver and Symposium on The others Present Status of the Quicksilver Industry (With Discussion) (37) 271-A.30 Observation on Ground Movement R. E. Palmer New York T30. 168 and Subsidences at Rio. Tinto Feb.. 1930 Mines, Spain (20) 274-A.31 Development and Installation of the C.L.Berrien New York T30, 139, 166 Hawkesworth Detachable Bit (29) Feb., 1930 276-A.32 Protective Measures . Against Gas 0. A. Glaeser New York T30, 129. 167 Hazards at United Verde Mine (11) Feb., 1930 287-A.33 Use and Cost of Compressed Air (12) R. S. Lewis New York Feb., 1930 314-A.34 Miami Copper Company Method of F. W. Maclcnnan New York T30, 39, YO Mining Low-grade Orebody (44) Feb., 1930 319-A.35 How Human Beings Respond to W. J. McConnell New York Changing Atmospheric Conditions Feb., 1930 (9) 324-A.36 Vertical and Incline Shaft Sinking at Arthur B. Foote San Francisco T30, 87 North Star Mine (21) Oct., 1929 32bA.37 Governmental Control of the Pro- W. E. Colby New York duction and Sale of Mineral Re- Feb.. 1930 sources (With Discussion) (16) 333-A.38 Some Recent Developments in Open- E. E. Hunner New York T30, 106, 117 pit Mining on the Mesabi Range Feb.. 1930 (25) 334-A.39 Mining Methods and Costs at Presi- V. D. Howbert El Paso dio Mine of American Metal Co. of R. Bosustow Oct., 1930 Texas (15) 339-A.40 Operation of Pressure Fans in Series W. 8. Weeks New York (8) V. 6. Grishkevich Feb., 1931 364-A.41 Top Slicing with Filling of Slices as H. Willey El Paso Used at the Charcas Unit of Com- Oct., 1930 pania Minera Asarco, S. A. (17) 373-A.42 Drill Sampling and Interpretation of H. T. Matson New York Sampling Results in the Copper G. A. Wallis Feb.. 1931 Fields of Northern Rhodesia (17)

Jan 1, 1930

By Xiangjun Zuo

This paper firstly reviewed the state of the art in the recycling of used Printed Wiring Boards (PWB), and then presented part of the authors study on the combustion of PWB powders with and without the addition of catalyst. During the combustion of PWB powders without catalyst addition, there were two obvious exothermic reactions, one at 300-380oC, the other at 450-500oC. With the addition of catalyst during PWB combustion, there were no obvious exothermic reactions, indicating that dehalogenation reactions are not exothermic: The results showed that NaHCO3 and CaCO3 were very efficient to control the emission of Br2 and C6H6, lowering 80% compared to the case without catalyst, Na2CO3 can slightly control the emission of Br2 gas but not for C6H6 gas mission, and NaOH has no any effect of the control of both gases.

Jan 1, 2009

By Julian Malnic

Transplanting the steps used in exploring and developing mineral deposits on land into the marine environment will help developers. While familiar to oil and gas explorers and many other sea-based industries, the marine environment is so alien to the 90s terrestrial miner that the phrase ?terrestrial mines in the sea? is useful for reinforcing the fundamental parallels in mining sulphides at sea and on land. As on land, the processes of ?pre-feasibility study? and ?feasibility study? will determine the economics of mining a deposit. For many, the step into the sea can detract from the need to follow these familiar and recognised steps used when any new deposit is found on land. The technology to mine sulphides in the 1500 to 2000 m depth range exists. Currently, it is not found in a single, integrated and commercially available system but every element available to build such as system is. Transplanting the thinking of the leaders of the terrestrial mining industry into the sea will perhaps be the greatest challenge and reinforcing the basic steps of discovery - pre-feasibility through to feasibility is the best way to achieve this. After all on land one doesn?t ask ?Can we profitably mine it?? before one can authoritatively answer ?What have we found??. Research by Nautilus Minerals Corporation suggests that the mining of seafloor massive sulphides (SMS) will not only be profitable but potentially lower in both capital and operating costs than prevail in most terrestrial deposits. Nautilus is also acutely aware that with the first SMS deposits under title, it will be setting the standards for seafloor mining into the new millenium. Indeed, we have trained on us not only the eyes of the mining industry waiting to see if SMS deposits really do offer radically better returns, but other stakeholders of the sea and the capital markets. Mistakes by any SMS developer could land all developers in ?hot water?. The rush to exploit our deposits for economic gain will be tempered by ensuring there is adequate public debate and consultation for our environmental code. Failure in any facet of a marine mining development could set back the move to the ocean floor.

Jan 1, 1998

By Marlyn King, Kevin Peterson

Power Decks are voids created in the bottom of the borehole through the use of a suspended Super Plug. Explosive energy is started downward at initiation creating high pressures which find relief at the comers of the borehole cylinder in the bottom of the hole. This relief creates a horizontal break to the neighboring boreholes - the same effect as presplitting. This “presplit” represents a change of mass to.the explosive energy,and it is reflected upward in the more efficient form of tensile waves. This provides better use of the explosive energy than compression waves. This technique has created a new way of looking at the ways that explosive energy is transported through the rock mass.

Jan 1, 2002

By D Craw, J Pope, B Peake

Southland contains over 70 per cent of New ZealandÆs recoverable coal resources, and an investigation into the potential effects of coal mining on SouthlandÆs water resources is therefore of interest. This paper investigates pit-lake water quality in relation to current mining activities within the sub-bituminous coal and lignite deposits of Southland. &nbsp; Water quality data was collected from pit-lakes in sub-bituminous and lignite deposits from October 2005 to March 2006. After periods of settled weather, turbidity increased with depth at the sub-bituminous pit-lake (10 - 21 NTUs from 5 - 30 m). In the stratified sub-bituminous pit-lake in March 2006, heavy rainfall caused higher turbidity in the epilimnion than the top of the hypolimnion (20 NTU vs 13 NTU) reflecting surface water runoff (up to 1993 NTUs) and epilimnion mixing. In contrast, turbidity at the lignite sites was variable due to the shallowness of the lakes, but noticeable increases following disturbance and adverse weather were recorded. High turbidity at the sub-bituminous deposits was attributed to the presence of clay minerals such as kaolinite whereas turbidity at the lignite sites was more likely short term and a result of heavier minerals such as quartz. &nbsp; Trace element concentrations at both sites were low when compared to mine waters in other coal areas in New Zealand and no samples exceeded ANZECC water quality trigger values for 80 per cent species protection. Pit-lake water pH levels were lower and more variable in the lignite deposit (4.18 - 7.30 vs 7.24 - 8.98 in the sub-bituminous deposits). In the lignite pit-lakes, higher concentrations of trace elements (eg Dissolved As - 0.034 ppm and Dissolved Mn - 1.09 ppm) and lower pH (ÿ4) were observed at the bottom of active pits compared to inactive pits. It is possible that quartz pebble conglomerates containing sulphide minerals within the lignite seams are responsible for this. &nbsp; Further investigation into the mine waters, waste rock and lake sediments will help get a better understanding of the results observed and long term processes that occur.

Jan 1, 2006