Search Documents

By Michel Robert

"In 1974, Copperfields Mining Corporation and Soquem formed a new company, Niobec Inc, to bring the niobium deposit of the St-Honore carbonatite into production.St-Honore is located in the Saguenay area, near the cities of Chicoutimi and Arvida, and about one hundred and forty (140) miles north of Quebec. The discovery of the carbonatite complex was made in the fall of 1967 as a result of an airborne radiometric survey in search of uranium. The detailed exploration of the carbonatite indicated two niobium-bearing formations besides the original discovery of a rare earths zone. During the following years, the niobium formations were defined by diamond drilling and a decline was driven down to obtain adequate samples for metallurgical evaluation. In 1974, after seven hundred (700) bench scale tests, eleven (11) months of pilot plant 2nd a worldwide market research, a joint decision was made to initiate the development of a fifteen hundred (1500) T.P.D. mine and mill, under the management of Teck Corporation. The construction of the facilities were completed in early 1976 both on time and within budget. Niobec is now the only north american and the world second largest producer of Niobium concentrate.The process used at Niobec was developed from the pilot plant programs and later modified by the mill personnel. A simplified flowsheet for this process is shown on the slide. Briefly, run of mine ore is crushed to minus 5/8"" and fed to a rod mill, ball mill, and screens circuit where the ore is ground to 92% passing 65 mesh. The ore is deslimed in two stages of cycloning, and the final cyclone overflow at 85% minus 11 microns goes to waste. The cyclone underflow is conditioned prior to flotation of a carbonate-apatite concentrate. This concentrate is cleaned twice and then pumped to tails. The carbonate rougher and cleaner tails are cycloned in two stages to change the process; water and then sent to the pyrochlore rougher flotation. The rougher concentrate is cleaned five times. This is followed by pyrite flotation to remove sulfur, leaching with hydrochloric acid to remove phosphorus and dyed to less than 0.1% moisture before being sent to packaging."

Jan 1, 1978

By S. F. Fu

The Charkhan Salt Lake area of the Chaidamu Basin in West China is characterized by soft super-saline soils with very high contents of soluble salts. From the engineering point of view, these saline soils are saturated, liquid-plastic and moderately to highly compressible lean silty clay and clayey silt. In the natural state, their allowable bearing capacity is only 60-80 kPa. As to the saturated lean silty clay, liquifaction in case of an earthquake of intensity 7 on the Modified Mercalli scale is considered likely. In order to improve the geotechnicai properties of the saline soils, stone colomn stabilization by means of vibroflotation was performed. As the geotechnicai properties of the soils are closely linked with the amount and composition of the soluble salt content, saline water with chemical content similar to that of the saline soils was used as flush fluid in the course of hole-making and column-forming, with a view to keeping unaltered the amount and composition of the salts in the soils and thereby precluding reduction in or loss of their strength. Systematic monitoring on the behavior of the foundation soils before and after the treatment and comparison of the numerical data thus acquired have shown good technical results, testifying to the effectiveness of stabilization of soft superealine soils by vibroflotation. As a result of the treatment, the allowable bearing capacity was increased one to two fold, accompanied by elimination of the liquefaction potential.

Jan 1, 2010

By S. Assemi

Interaction forces between a hydrophilic silica particle and an air bubble were measured by atomic force microscopy using simplified model systems with deionized water and dilute KCl solutions. Contributions from the hydrodynamic force were minimized by using a low piezo speed. Particle-bubble separation distance and the bubble spring constant were calculated from linear regression of the piezo extension versus cantilever deflection. The bubble surface potential was then estimated from fitting the AFM-measured forces to the Hogg-Healy-Fuerstenau (HHF) model, using the surface element integration (SEI) method. Surface potentials obtained for the bubble at a low applied force were comparable with the literature data, suggesting that the simplified model used here can give a reasonable estimation of the bubble surface potential under moderate applied forces. Interaction forces between a silica particle and an air bubble were also measured at different locations on the air bubble surface. The force curves obtained at the edges of the bubble fitted very well to the theoretical force curves regardless of the applied force, while curves obtained at the center and halfway to the center, were more difficult to fit, in particular at higher applied forces (> 13 nN), suggesting that force curves obtained at the edges of the air bubble might be less prone to deformation effects.

Jan 1, 2008

By I. Ewart, E. Roux

Skorpion Zinc operates a solvent extraction/electrowinning zinc plant producing over 150 000 t/a of special high grade (SHG) zinc (>99.995% Zn). In the current flow sheet copper and cadmium are cemented from the neutral leach solution using zinc powder, to prevent galvanic corrosion of plant equipment and build-up of copper in plant solutions. This process is effective but unfortunately consumes expensive zinc dust and produces a low value copper product. The EMEW® (Electrometals electrowinning) technology of Electrometals Technologies Ltd. uses a rapid flow of electrolyte through a cylindrical cell to deposit copper or other metals from dilute solution (less than 1 g/L) [1]. The copper can be deposited as powder or may be harvested as a tubular cathode product. The advantage of the use of EMEW® technology at Skorpion Zinc will be to eliminate the use of expensive zinc dust and to produce a high value copper product for sale. Following extensive bench test work, a piloting campaign was carried out at Skorpion Zinc. The tests demonstrated the ability of the EMEW® cell to effectively remove copper from solution through direct electrowinning at lower operating cost than cementation. Keywords: Skorpion Zinc, copper, cementation, direct electrowinning, EMEW®

Jan 1, 2007

By A. M. Childs, R. F. Mather, K. R. Rawling

"The challenges encountered in the design and construction of mines and their process facilities today are becoming more intense and the engineering more competitive. The need to incorporate new techno1ogy to compensate for ever rising costs is always present, but its application in the harsh environment of Northern Canada increasingly requires the inclusion of new proven methods and innovative approaches to arrive at economically attractive projects.This paper deals with the development of the process design for the Cullaton Lake Gold Mine in the Northwest Territories. Particular emphasis is given to the interaction of the imposed construction and testwork schedules, and their effect on certain process decisions.The challenge that faced the project team may be defined by the following factors:1. A schedule which required that metallurgical testing, engineering, and procurement and delivery of all equipment and construction supplies should be complete within a period of ten months.2. Transportation of all personnel, equipment and supplies to the site by airlift, as no road was available or affordable.3. A six week period when transportation to the site was impossible.4. The extremes of temperature beyond the tree line in the Northwest Territories.5. A complete lack of infrastructure in the area."

Jan 1, 1983

By Silvana Costa

Rapid changes in technology and human resources trends require the mining industry to plan carefully for new work camps. The abandonment of the “mining town” concept and rapid increases in the adoption of long distance commuting have intensified the need for improved planning and monitoring of existing and upcoming operations. New mines will have an increasing Aboriginal participation in their workforce and will mostly to be located in remote and in extreme weather conditions. In this sense, the intensification of the use of the commuting system has increased the need for improved planning and monitoring of upcoming operations. Given that mining development is experiencing a surge in activity in Canada, particularly in remote and northern locations significant number of individuals will get jobs that involve mine camp communities. Some employees will spend half of their working lives at the mine site for a period of time that can last up to 30 years. Even though investments have been made towards particularly high quality physical environments, mine camp policies, programs and employee quality of life in mine camps have not been studied in any depth.

Sep 12, 2005

Jan 1, 1971

By Cecilia Arrue, Dominic Fragomeni, N. O. Lotter

"A statistically designed benchmark mill survey was carried out in July 2005 at the Kidd Creek Concentrator, D Division circuit, which processes Ni/Cu ore from the Montcalm deposit. A structured statistical survey approach was followed, together with defined quality controls, which would assign a 95 percent level of confidence in the result.A set of six surveys were completed over a limited time; the corresponding stream samples of the surveys found acceptable were combined to obtain high confidence composite samples. The head grade of each survey is compared to two distributions to test its acceptability; surveys that fail to conform to these trials are rejected. The accepted set of surveys, which is a robust representation of the process, is prepared into a composite for QEM-SEM analysis and mass balance purposes.Where the above practice is a standard procedure in Falconbridge for QEM*SEM purposes, in this case each individual two-hour survey unit was measured and analysed for a mass and value balance. It is shown that none of the individual mass and value balances close as well as the composite set of accepted two-hour survey units. This founding is in keeping with the averaging properties of the Central Limit Theorem.INTRODUCTIONMontcalm OperationsNi/Cu bearing ore from the Montcalm deposit is being processed at the Falconbridge, Kidd Creek Concentrator in a modified D Division circuit. The circuit was commissioned in the fall of 2004. Ore is crushed at the minesite to –19 mm and trucked to Kidd for delivey into the 4 parallel fine ore bins.Ore is milled in a rod mill followed by cyclones and 2 parallel ball mills. The grinding circuit treats Montcalm ore at an average feed rate of 100 wet tonnes/hour (750,000 tonnes/annum) and produces a flotation feed particle size of 83% -53 um. A simple flowsheet including bulk Cu/Ni roughing and 2 bulk cleaning stages followed by Cu/Ni separation in 2 stages is practiced. Soda ash is used as a pH modifier in bulk flotation. SIBX is the collector. Lime and Dextrin are added into Cu/Ni separation for the depression of pentlandite."

Jan 1, 2007

By N. A. Gjostein

From their study of the anisotropy of grain boundary mobility in aluminum, the authors conclude that tilt boundaries have a higher mobility than twist boundaries because the atomic misfit at the pure-twist boundary is relatively small compared to the misfit at a tilt boundary for a given amount of misorientation. If this is true, then one would expect a twist boundary to have a lower grain boundary energy than the corresponding tilt boundary. Fig. 6, taken from the work of Gjostein and Rhines,10 shows that this is indeed the case for [001]-cu tilt and twist boundaries in the high-angle region, thus lending support to the authors' conclusion.

Jan 1, 1968

By Philip Weaver

The MIDAS project is funded by the European Commission (DG Research) and began on the 1st November 2013. The project will investigate the environmental impact of deep-sea mineral and energy extraction: specifically, polymetallic sulphides, manganese nodules, cobalt-rich ferromanganese crusts and the potential mining of rare earth elements. As deep-sea mining becomes ever closer, and the International Seabed Authority begins to develop its regulatory framework for exploitation of deep-sea minerals, MIDAS is well timed to provide fundamental scientific information. The MIDAS partnership represents a unique combination of scientists, industry, social scientists, legal experts, nongovernmental organisations and small and medium enterprises. MIDAS is carrying out research into the nature and scales of the potential impacts of mining including 1) physical disturbance of the seabed by mining, the creation of mine tailings; 2) the potential effects of particle-laden plumes in the water column, and 3) the possible toxic chemicals that might be released by the mining process. Key biological unknowns, such as connectivity between populations, impacts of the loss of biological diversity on ecosystem functioning, and how quickly the ecosystems will recover will all be addressed. The plan is to use this information to aid development of recommendations for best practice in the mining industry. A key component is the involvement of industry within the project and through stakeholder engagements to find feasible solutions. The project will work closely with European and international regulatory organisations to take these recommendations forward into legislation. A major element of MIDAS will be to develop methods and technologies for 1) preparing baseline assessments of biodiversity, and 2) monitoring activities remotely in the deep sea during and after exploitation, including ecosystem recovery. To carry out this work MIDAS is conducting a number of research cruises to examine the above issues at potential sites for exploitation of SMS and nodule deposits. This talk will present some of the recent findings of the project.

Sep 1, 2014

By O. Mejia, J. Drozdiak

"This paper summarizes a comprehensive energy and cost study comparing an existing SAG mill based circuit at Huckleberry Mine with two proposed circuits involving comminution technologies which are associated with energy efficiency: high pressure grinding rolls (HPGR) and high speed stirred mills. The specific energy requirements expressed as kWh/t for the proposed circuits were determined from pilotscale HPGR and stirred mill testing conducted at the University of British Columbia. Samples and operating data were collected from Huckleberry’s copper-molybdenum concentrator to evaluate current mill performance for comparison. To support the base case, the SABC circuit was modeled using JK SimMet® software. The main comparison focused on the complete energy requirements for each circuit, including materials handling equipment such as conveyors, screens, feeders and pumps. This paper also provides capital and operating cost estimates for each of the comminution circuits. The results showed that the HPGR - ball mill circuit achieved a 21% reduction in energy consumption over the existing SAG - ball mill circuit at the same P80 grind size of 160 µm. At a grind of 80% passing 75 µm, the HPGR - stirred mill circuit showed a 34% reduction in energy compared to the base case. It was concluded that the energy reduction for the new flowsheets significantly improved the economics of the Huckleberry comminution duty.INTRODUCTIONUp until now, tumbling mills such as AG/SAG mills and ball mills have had a dominant bearing on the design and economics of comminution circuits. However, it is commonly agreed that the majority of employed comminution processes are energy intensive and energy inefficient, accounting for up to 80% of overall process plant energy consumption and having an efficiency of as low as 1% (Abouzeid and Fuerstenau, 2009; Fuerstenau and Abouzeid, 2002). The U.S. department of energy reported that there is a potential to reduce energy consumption in the metals industry by up to 61% from current practice to bestestimated practical minimum energy consumption; suggestions included the implementation of best practices and the adoption of energy efficient mining and mineral processing technologies such as advanced blasting techniques, high pressure grinding rolls (HPGR) and stirred mills (U.S. DOE, 2007)."

Jan 1, 2013

By J. -M. Rescoussier

Due to Important settlements inducing major structural damages, the western part of the Grand Littoral shopping centre has been closed in 1997. The present paper describes the project of underpinning including not only micropiles under the structure of the building but also a reinforcement of the soil located between the shopping centre and the edge of the embankment surrounding the western part of the shopping centre. The aim of this reinforcement is to reduce existing horizontal movements to allowable values.

Jan 1, 2002

By John Feddock

A recent increase in energy demand has resulted in the rapid growth of coal consumption in the People?s Republic of China (PRC), which is the largest coal producer and consumer in the world. Reportedly, the safety issues in Chinese coal mines have been improving, but the number of fatalities and serious injuries continues to be alarmingly high. The number of fatalities from catastrophic accidents have prompted researchers to review the Chinese mine safety situation and to look for potential solutions. Marshall Miller & Associates, Inc. (MM&A), along with various collaborators, has investigated these issues as part of its work on various projects in the PRC and has discussed the concerns with relevant Chinese officials. Preliminary investigations by MM&A of coal mine accidents during 2001?2006 in the PRC indicate that 65%-78% of the total fatalities were the result of gas explosions and roof falls in underground mines. Even though the drainage of methane has been practiced for decades, current practices do not always produce satisfactory results due to technical constraints and equipment limitations. Based on prior experience of in-seam degasification at the Daning Coal Mine located in Shanxi province, MM&A believes that in-seam directional drilling technology can be a viable solution to degas the low-permeability Chinese coal deposits. This paper 1) reviews current Chinese coal mine safety conditions, 2) analyzes the advantages/disadvantages of current degasification practices in China, and 3) presents the pre-mining degasification practices for the longwall panel at the Daning Coal Mine.

Jan 1, 2007

By K. Heasley, A. Yassien, A. Khair, S. Peng

There are three major components of a fully grouted roof bolt which primarily determine its ability to develop and sustain load: the steel rebar, the resin annulus, and the rock/grout interface. The untensioned, fully grouted roof bolt is subjected to loading only when the surrounding rock deforms. Vertical rock deformation is generally a result of strata sagging and bedding plane separation, whereas horizontal deformation is typically a result of bedding plane sliding. These two types of deformation create different types of internal loads with-in the roof bolt, tensile stress for vertical rock deformations and shear stress for horizontal rock deformations. Also, as a result of the mutual load transfer between the rock and bolt, shear stress will be developed along the grout/rock interface. According to the exact bolt loading conditions, different failure modes may occur: bolt axial failure, bolt shear failure, and shear failure along the grout/rock interface. Understanding these possible failure modes and their root causes is the key to eliminating roof failures in underground mines employing fully grouted resin bolts. Using ABAQUS 5.8, a finite element model was developed to simulate the components of the fully grouted bolt and its interaction with the surrounding roof strata. Several models were conducted to investigate how load transfer occurs between the rock and the bolt under different geological and mining conditions. The effects of bed-ding plane location and properties, and strata sequence on bolt stability were studied. Also, the effects of hole roughness on bolt stability were discussed. Bolt axial failure was not observed within the range of the studied parameters; however, a combination of high overburden depth, a bedding plane located at 2 to 3 ft from the roofline or a low coefficient of friction along the bedding plane caused strata sliding and shears failure in the bolt. Also, in the case of a weak immediate roof, the shear stress at the grout/rock interface could exceed its ultimate capacity lead to slippage.

Jan 1, 2004

By Rodney R. Koch

The phys ica l properties of gold should faci li tate its detection. However, the average concentration of gold in the ea rth's cru st precl udes the ability of geophys ical methods to detect the metal directly. In order to effectively pursue geophys ical detection and location of gold mineralization there must also be geological input - i.e. a model. This will lead to the selection of the appropriate geophy ical techn ique(s) in the fo llow-up programs. Interpretation of the fie ld survey data is of con iderable importance in expl oration geophys ics. Analytical techniques such as cont inuation, fi ltering, and spectral analys is, are now routinely empl oyed in the analys is of survey data to aid the interpretation process. The uccessful application of geophysical methods and the use processing techniques is demonstrated by two recent Saskatchewan discoveries. The first, the Star Lake 21 Zone, with reserves of 230,000 tons grading bener than 17.14 git Au associated with a disseminated sulphide quartz-bearing shear zone yielded geophysical anomalies that were distinctive, obvious, and would have lead directly to its discovery. The econd , the Laurel Lake Prospect, with ore grade intersections of 28.0I git Au and 52 .46 git Ag· over 5.49 m, resulted in numerous geophysical anomalies. However, none of these anomalies demonstrated association with the mineralization until processed results indicated that structural features crosscuning regional trends were important cont rol mechanisms for the mineral ization.

Jan 1, 1986

By S. E. Phillipson

The Late Miocene San Cristobal Ag-Zn-Pb deposit represents syngenetic and epigenetic mineralization with low- and high-sulfidation characteristics. Geology is characterized by barren dacitic ring fracture domes, mineralized resurgent rhyodacite domes, strongly altered and mineralized tuffaceous lacustrine sedimentary rocks, and an extensive crystal-lithic tuff debris apron. The ore body is hosted by intra-cauldron sedimentary rocks and breccias. Fluid inclusions suggest that silver, lead, and zinc were transported as chloride complexes and precipitated by cooling in veins from <5 wt. % NaCl eq. fluids at 170°-215° C. Silver associated with resurgent rhyodacite was transported as a chloride complex and precipitated by increased H2S activity or increased fluid pH.

Jan 1, 2001

By R. S. Dean

[Methods s of preparing the manganese metal that has been used in chemical and metallurgical investigations have passed through a cycle. Most of the investigations made e before the turn of the century, used Moissan&apos;s pyrophoric man manganese.3/ This material was made b; electrolysis into a mercury cathode and distillation in vacuo. The material was essentially pure, and investigations in which it was employed (with proper precautions against oxidation) led to accurate results on tie intrinsic behavior of metallic manganese.]

Jan 1, 1941

By Bruce Geller

The 2004 Prospectors and Developers Association of Canada (PDAC) conference contained an air of optimism and excitement that has not been seen since 1997. Many segments of the mining industry are alive and well. This is largely a reflection of improved metal prices, themselves due to the strong euro and improvements in Asian economies. Those factors offset higher oil prices, a weaker U.S. dollar and concerns about the Middle East. This report is an overview of the conference. It is supplemented by an examination of conference handouts, abstracts and a few complete papers that are on the PDAC’s Web site www.pdac.ca. Sixty PDAC 2004 abstracts are available at the same site, along with 15 complete papers in PDF format. The conference was held March 7-10 in Toronto, Ontario. It was attended by a record 9,200 delegates from 85 countries. About 8,000 people from 74 countries attended the 2003 conference.

Jan 1, 2004

By Jun Han

Coal has been mined in the Kailuan mining area for more than 130 years. The remaining reserves consist of, in large part, coals that would have been considered economically unminable or technically not feasible by the previous generations. Some of the current operations have to resort to overmining because the lower seams had been extracted in the past. This paper deals with the feasibility and proper layout of mining roadways of overmining carried out in the No. 5 seam of Qianjiaying coal mine of Kailuan mining area using numerical and physical simulation. FLAC2D was used to investigate the characteristics of stress and displacement in the overburden after extraction of the lower seams. It also analyzed the proper layouts of gateroads in the upper seams, i.e. locating them in the stress-relief zone of the gob so that their stability can be easily maintained. In addition, a two-dimensional physical model was constructed for investigation of damages to the upper seams due to mining of the lower seams. Finally, based on the results of investigations, proper gateroads layout was designed and successful extraction was implemented for panel 1357 in the No.5 seam.

Jan 1, 2009

Lean Iron Ore Beneficiation in India

Sep 13, 2010