Search Documents

By R. A. Williams

The Pascua Lama Project is situated on the border of Chile and Argentina at an elevation of 4,800 m. The ore contains gold, silver and copper, and an initial milling production rate of 33,000 t/d is planned. The mineralogy of this deposit is unusual. The ore is hard and abrasive, and it contains a complex array of sulphate minerals, such as chalcanthite, jarosites and alunites. The sulphides are predominantly enargite and pyrite. A novel flowsheet has therefore been developed, which includes dry grinding and ore washing to remove and then neutralize the soluble salts, prior to flotation, cyanide leaching and Merrill-Crowe recovery of the precious metals. These metallurgical issues and challenges associated with plant design and construction in the high and remote Andes Mountains make this a particularly challenging project.

Jan 1, 2001

By Yogesh Prashar

Three conventional uplift tests and 12 Rapid Pile Load Tests (RLT) were performed on total of fifteen 16-inch square pre-cast concrete driven piles at a test site in Emeryville California in December of 2000. The uplift tests were performed in accordance with ASTM standards, and the RLTs were performed using a FUNDEX RLT. The RLT is carried out by dropping a mass of 25-tons on top of the pile, thereby inducing a force that is measured by a load cell. An optical lens records the vertical deflection of LED's that are mounted on the pile. Ultimate uplift and compression capacities of each of the fifteen piles were determined using the Davisson method. Soil parameters were calibrated by back-calculation (cohesion and internal angle of friction) using both the results of conventional uplift load versus deflection curve, as well as the results of the triaxial compression tests. A two-dimensional finite difference model including soil elements, and structural elements representing the test pile was setup using the computer program Fast Lagrangian Analysis of Continua (FLAC). FLAC was used to simulate both the uplift as well as the RLT. Strength increase of cohesive material was also accounted for in the analysis. Numerically simulated and theoretically computed pile capacity curves and axial deformation variation with applied load curves are in close agreement to the observed curve during the field test. Conclusions are made from this test site regarding the factors influencing results of RLT.

Jan 1, 2002

[ ]

Jan 1, 1981

During the period 1979 thru 1982. Multi Mineral Corporation conducted a mining research program at the United StAtes Department of the Interior's Bureau vi Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and. the results are described in this report.

Jan 1, 1983

Geology grads mine heated job market Salaries up 44 per cent in three years ?[Geology student] passed up a $100,000-a-year job at a mining company last December when he finished his degree in geology. The 24-year-old Canadian said he?s confident he?ll get a better offer.? Rob Delaney and Stewart Bailey, Calgary Herald, Published: Saturday, March 15, 2008 Massive shortages across the mining industry > Trades and operators are a large component > Technical people are equally hard to find > Students are in an excellent positions to secure exciting jobs > Experience is at a premium. Why?

May 1, 2008

By Peter Townsend, Sergei Diachenko, Allan Moss

The Palabora Mining Company has successfully extended the life of its operation by developing a 30,000tpd block cave underground mine below the now closed open pit. The process of transitioning from surface to underground mining has been technically, operationally and managerially challenging. This has been due to a number of factors; in particular, the development of a block cave in a very competent rock mass. The competence of the rock mass is clearly demonstrated in the open pit that preceded the block cave, one of the steepest deep open pit excavations in the world. With cave breakthrough, however, the pit was ?instantaneously? deepened by 400m causing a major failure of the northwest wall involving close to 100Mt of waste material.

Jan 1, 2006

By Robert W. Bruhn

An investigation was male of ground response to pillar retreat mining in a 1.7 meter thick seam at 108 meter depth at a site in northern West Virginia. This paper describes mining-related stress changes and movements at nine level, displacements within the overburden, ground surface subsidence and groundwater level variations. Subsidence approached 40 per cent of the nine height ad continued more than a year after mining. Water levels declined la certain deep-lying strata.

Jan 1, 1984

By I. Cadoff, E. Miller, K. Komarek

Jan 1, 1960

By J. F. McIlwain

The Bureau of Mines has investigated fumes generated by selected welding electrodes used in mines in order to help determine their relative health hazard potential. Fumes were generated and collected in an enclosed chamber for subsequent generation rate and chemical constituent determination. Shielded metal arc electrodes from the following groups were tested: AWS types E308-16 and E310-16 stainless steel, ECoCr-A Co-Cr hardfacing alloy, ENiCr Ni, an Mn-Cr buildup alloy, E7018 carbon steel, and EII018-M low-alloy steel. Flux-cored wire electrodes of this last group also were tested. Fume generation rates and the chemical composition of the fumes were measured. From these data, exposure in-dices were determined, which give a relative measure of the health hazard potential of using the electrodes. The effect of welding onto build-up alloy layers on the fume composition also was examined for five of the higher alloy groups.

Jan 1, 1987

By José Fernandes De Oliveira

El presente texto aborda los resultados de tres estudios realizados por Microscopía Electrónica de Barrido con Energía Dispersiva (SEM/EDS) en el Laboratorio de Caracterización Mineralógica, donde destaca la importancia de la técnica en el sector de minería y materiales. El primer estudio comprende el análisis de los contenidos de fierro y manganeso en concentrado de zinc, donde se verifica que la esfalerita contiene fierro cerca del límite aceptable de 5%. El segundo estudio realiza una caracterización mineralógica de muestras con minerales de plata, para conocer el estado de la plata (inclusión, solución sólida, encapsulada), con qué minerales está asociada y si puede ser liberada. Finalmente, el tercer estudio refiere el análisis de secciones fracturadas de tornillos de latón para evaluar las causas del rompimiento prematuro de los tornillos.

Sep 12, 2011

Many industries base their decisions on the assaying of tiny analytical sub-samples. The problem is that most of the time several sampling and sub-sampling stages are required before the laboratory provides its ultimate assays using advanced chemical and physical methods of analysis. As long as each sampling and sub-sampling stage is the object of due diligence using the theory of sampling it is likely that the integrity of the sought after information has not been altered and the generated database is still capable to fulfil its informative mission. Unfortunately, more often than not, unawareness of the basic properties of heterogeneous materials combined with the unawareness of stringent requirements listed in the theory of sampling, lead to the conclusion that massive discrepancies may be observed between the expensive outcome of along chain of sampling and analytical custody, and reality. There are no areas that are more vulnerable to such misfortune than sampling and assaying for trace amounts of constituents of interest in the environment, in high purity materials, in precious metals exploration, food chain, chemicals, and pharmaceutical products. Without the preventive suggestions of the theory of sampling serious difficulties may arise when making Gaussian approximations or even lognormal manipulations in the subsequent interpretations. A complementary understanding of Poisson processes injected in the theory of sampling may greatly help the practitioner understand structural sampling problems and prevent unfortunate mistakes from being repeated over and over until a crisis is reached. This paper presents an overview of the theoretical, practical and economic difficulties often vastly underestimated in the search for quantifying trace amounts of valuable or unwelcome components.

Jan 1, 2010

By Kurt RP Petersen, Hendriena van der Walt

With the decline in fine diamond production from the Argyle mine in Australia, there is a greater emphasis on efficiently treating the finer size fractions through a DMS circuit. Although it is generally well understood that smaller diameter cyclones are more appropriate for this application, practical results do not necessarily meet this expectation. In this paper the operational performance of particular sized cyclones throughout the group was compared. Based on the results there is evidence that under certain practical operating conditions, small cyclones are not necessarily best for fine size particle treatment, particularly given the production pressures faced by all mines. However, there seems to be considerable merit in using larger sized cyclones, which tend to exhibit less performance variability, irrespective of operation conditions.

Jan 1, 2006

By D. K. Deardorff

The hafnium-vanadium phase diagram was constructed within an estimated accuracy of ± 10° C and ± 2 wt pct composition. Alloys for investigation were melted under an atmosphere of purified helium by nonconsumable tungsten-electrode arc melting on a water-cooled copper hearth. Melting points were determined by optical pyrometer, and the remaining phase relationships were investigated by metallography, thermal analysis, and X-ray diffraction. The existence of a face-centered cubic intermetallic compound HfV2 (a = 7.38 A) was confirmed. A eutectic reaction occurred at 20 wt pct vanadium and 1,395° C to yield HfV2 and 8 solid solution. HfV2 melted incongruently by a peritectic reaction at 1,480° C, and the 3 solid solution decomposed eutectoidally at 1,165° C and 6 wt pct vanadium to yield HfV2 and a solid solution. The eutectoid, the eutectic, and the peritectic isotherms extended from 1 to 36.3 wt pct vanadium, from 8 to 36.3 wt pct vanadium, and from 26 to 89.5 wt pct vanadium, respectively. Terminal solid solubilities of hafnium in vanadium at 1,300° C and of vanadium in hafnium at 1,100° C determined to be about 3 and 1 wt pct, respectively.

Jan 1, 1965

By A. L. Engel

This report is a compilation of results of preliminary tests on scheelite (tungsten) ores and tailings. These investigations were made to assist in establishing satisfactory treatment methods for small-scale concentrator operations, or to indicate a. method for conserving previously lost mineral values in old tailings, if possible. A discussion of test procedures is included, as it was felt that this would add to understanding the results reported under the several projects. The treatment of scheelite ores has become more or less standardized. Important differences occur in textures of ores from various mining districts. However, and this must be considered when planning ore-dressing operations. In most of the present investigations, only a limited amount of work was done, usually just enough to answer a specific question in regard to a particular ore or concerning local conditions. Two methods of treatment included gravity concentration, magnetic separation, and flotation.

Jan 1, 1952

By J. E. Lawver, B. J. Clingan, R. E. Snow

Response surface methodology is a well-known and powerful technique for determining optimum conditions in flotation systems. One disadvantage is the onerous task of the numerical calculations and curve plotting. This paper describes a system in which the investigator simply selects the range of several flotation variables after which the design of the experiment, data analysis, generation of response surface equations, and response surface plots are automatically carried out using a digital computer and a computer-driven curve plotter. Several typical response surfaces of important variables in phosphate flotation are presented as examples.

Jan 1, 1980

By Claude Bazin, Jalna Lamontagne

"The operators of mineral processing plants collect daily samples from strategic process streams with a view to prepare production balances to assess plant performances. The rules to minimize the risk of systematic sampling errors are known and applied in many mineral processing plants. The mass of the sample to be collected is calculated to yield a target measurement reproducibility considering the fundamental error associated to the sampling of heterogeneous material. This paper demonstrates that this practice is partly valid if one does not account for the time variation of the ore composition during the day. The concept is demonstrated using samples collected on a 30 minute basis from different streams of a gold ore concentrator. Results show that depending of the natural variability of the stream characteristics the mass of the daily samples may not be the critical variable to obtain reproducible measurements. On the other hand the number of cuts taken during the day could impact on the variance of the measurements obtained from daily samples.IntroductionMineral processing plants may treat several thousand tons of ore every day to produce concentrate or impure gold ingots. The operation and performances of these plants are monitored on a daily basis through the collection of ore samples from various streams of the processing circuit. The samples are prepared and assayed to obtain the concentrations of target elements that are subsequently used to calculate the mass flowrates in the streams of the circuit and ultimately the distribution of the target metals for the estimation of the plant performances (Morrison, 2009; Lachance and Leroux, 2016).The acquisition of representative and reproducible samples is therefore the first step in the characterization of plant performances. The term representative sample is used here to indicate an unbiased sample, i.e. a sampling procedure that does not introduce a systematic error. Rules for the collection of unbiased samples are reviewed in the literature by different authors (e.g. Morrison, 2009) and are not discussed in this paper. The term reproducible indicates the dispersion of the measurements around the average value of a characteristic of a stream meets an acceptable level of variance. The reproducibility of a measurement process (sampling and analysis) is assessed by the relative standard deviation or coefficient of variation of the measurement that is a function of the sampling and assaying errors (Morrison. 2009; Gy, 1979). Usually the focus is put on the fundamental error of sampling whose variance can be controlled by the choice of the primary sample mass or adequate particle size reduction during the preparation of secondary or tertiary samples extracted for the chemical analysis. When a sample is taken from a stream that exhibits a time varying characteristic, the obtained measurement exhibits a variability that is not only a function of the sample mass but also of the natural variability of the ore in the sampled stream. This paper examines this aspect of the sampling of a time varying process on the reproducibility of composite samples for a day of production."

Jan 1, 2017

By T. M. Tharp

Attempts to analyze the stability of slopes, foundations and underground openings in discontinuously jointed rock have generally assumed full joint continuity or ignored the role of stress concentration at the tips of discontinuous joints. The most common approach in rock slopes is to consider a failure plane consisting of coplanar, but discontinuous joints separated by intact rock. The intact rock is assumed to fail in shear as a MohrCoulomb material and to contribute a strength component proportional to the fraction of the failure plane that is intact rock (Jennings, 1970). An alternative approach by Stimpson (1978) applies Lajtai's (1969) theory for shear strength of discontinuously jointed rock masses to slopes. Lajtai allows tensile failure in the intact rock of a composite surface. This theory yields lower shear strength than that of Jennings (1970) except in the presence of high normal compression, however it also fails to account for the stress concentration at the tip of a discontinuous joint. For a given slope geometry, stresses increase with slope height, but in both of these models rock mass strength is independent of size. A fracture mechanics analysis shows that particularly for small slopes, rock mass strength decreases with size.A continuous stepped failure surface produced by propagation of preexisting joints may develop at lower shear stress than pre¬dicted by the Jennings (1970) or Lajtai (1969) models. This fracture mechanics model applied to slopes in competent rock is more realistic in its assumed failure mechanism, and for large slopes more conservative than the Jennings (1970) or Lajtai models (1969).

Jan 1, 1984

By Shelby Z. Palya

"The Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mining-substances; to promote health and safety, in the mineral industries; to conserve Material resources , and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other Mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes reports and articles published during the period January 1, 1975, to December 31, 1979. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960; 2 the 50-year list, of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960; 3 the 5-year lists of publications and articles, from January 1, 1960, to December 31, 1964,, from January 1, .1965, to December 31, 1969,5 'and from January '1, 1970, to December 31, 1974; and the annual ,lists of Bureau publications and articles from January, 1 to December 31, 1975,7 from January 1, to December 31, 1976,8 from January 1 to December 31, 1977, and from January 1 to December 31, 1978."

Jan 1, 1981

By Eric E. Unger

Results are presented of a census of the machines used in surface coal mines in the United States. The numbers of each machine type and model reported to be in use are tabulated for large and small mines in the Eastern, Central, and Western regions. Also tabulated are the average daily usage times of the major machine categories and the numbers of machines that have acoustical and other cabs. Projections of the total numbers of primary production machines are given. It is found that heavy tracked dozers and wheeled front end loaders constitute the most prevalent machine types, and that generally a very few models of machines made by one or two manufacturers constitute a major fraction of the population in each machine category. About 70 percent of all machines are reported to have some kind of cab, and about half of these are reported to be acoustical gabs; it is noted that acoustical cabs generally came into significant use since about the early 1970's. It is observed that the percentage-wise mixes of equipment types used in the various categories of mines differ significantly for only a few types of machines, notably for heavy dozers and loaders, and for haulers, highway trucks, and internal-combustion engine-powered shovels and draglines.

Jan 1, 1977

By W. J. Birch, R. Farnfield

The use of electronic detonators to control blast vibrations has been previously established by many authors. This is performed by determining the optimum delay period between the blast holes for a particular pattern that can accurately control the firing frequency of the blast, which in turn has a direct bearing on the frequency composition of the ground vibrations recorded at a particular location. This was established by Pedgen, Birch, Hosein & Farnfield (2006) whereby like-for-like comparison tests between non-electric and electronic blasts were carried out in a limestone quarry in northern England. They demonstrated that resulting peak particle velocity values recorded at near and mid-field distances were primarily a product of the firing frequency of the electronically initiated blasts.

Jan 1, 2009