Search Documents

By Frank Yu, Bob Fukuhara

"The Stillwater mine is a 3,000 tons/day platinum/palladium underground mine and flotation concentrator located in the Beartooth mountain range in south-central Montana. The site elevation is 5,000 feet above sea level providing a climate with pleasant summers and cold winters. The winters are particularly characterized by very strong winds.The mining methods at Stillwater had been variations of overhand cut-and-fill and some blast-hole stoping. Until construction of the paste back-fill plant, mine back-filling was being practiced using classified hydraulic sand-fill methods. Where higher strengths were necessary, cement was added to the hydraulic fill, however, excessive quantities were necessary due to significant losses with the water drainage from the comparatively low-density fill. There was a need for higher strength back-fill with reduced cement content to augment the hydraulic-fill process.In early 1998, Stillwater Mining Co. commissioned AGRA Simons (then H.A. Simons) in a joint venture with The Industrial Company, TIC, to design and construct a treatment facility to re-process the mill flotation tailing, incorporating the following process alternatives:Produce 100 tph of low strength paste with unconfined compressive strength of 25 to 50 psi,Produce 100 tph of high strength paste with unconfined compressive strength of 100 to 125 psi,Direct all of the excess mill tailing to the sand-fill plant,While no paste is being produced, pump all of the mill tailing to the sand-fill plant,While no paste is being produced and the sand-fill silos are full, direct the mill tailing to the tailing pond.The paste backfill plant was therefore to be designed to produce the two different types of backfill paste as well as have the function of being the distribution center for the mill process tailing .Moderate to high slump pastes would be required because of the comparatively long horizontal transport distances, up to 8,000 feet, and the requirement for a low angle of repose to fill the stope evenly without numerous discharge points."

Jan 1, 2000

By José De Piérola

En los procesos de flotación y lixiviación de la producción de cobre se utilizan aguas recicladas y agua fresca. Este último es un insumo indispensable para ambos procesos, ya que constituye un elemento determinante del volumen de producción, así como un medio de vinculación obligado con el entorno social de las operaciones. En ese sentido, el presente texto describe la utilización del agua- en tanto representa un componente de rentabilidad relacionada al costo, al equilibrio del aprovechamiento con el comportamiento de la fuente y a la sostenibilidad con el entorno social, lo cual implica compartir el agua y recursos económicos para una planificación y adecuada priorización en su asignación.

Sep 9, 2007

By Alicia Esther Ares

The family of Zn-Al (ZA), Zn-Ag and Zn-Al-Ag (ZINAG) alloys offers high mechanical properties, ease of finishing, the advantage of low energy and pollution-free melting. Also, present alternatives to the well developed alloy systems, such as brasses, bronzes, cast irons and aluminum alloys. The main objective of this paper is to measure thermal parameters in ZA, Zn-Ag and ZINAG hypoeutectic and hypereutectic alloys directionally solidified which present columnar, equiaxed and columnar to equiaxed transition structures (CET). Also, estimate the mechanical properties, such as microhardness and tensile parameters and correlate these with the thermal (cooling rate) and structural parameters (grain size and dendritic spacing). The different types of structures were analyzed with optical and scanning electron microscopy. The results showed the influence of concentration, microstructural arrangement and thermal conditions during solidification on the mechanical properties. The results of the present investigation are compared with previous experiments.

Jan 1, 2010

By W. P. C. Duyvesteyn, B. J. Sabacky

Reprinted with revisions from Extractive metallurgy of copper, nickel and cobalt, volume I: Fundamental aspects. ed. Reddy R.G., Weizenbach R.N. Warrendale, Pennsylvania: The Minerals, Metals and Materials Society, 1993. Development work on the Escondida process, concluding with the successful operation of an integrated leach-SX-EW pilot plant and a pilot flotation plant for the upgrading of leach residues, demonstrated that all major process objectives could be achieved. Extraction of 40% of copper in concentrates containing monovalent copper was achieved with essentially no oxidation of sulphide sulphur. The Cu contents of leach residues from four different types of concentrate were successfully upgraded to the original feed grades, giving a product that has potential as a high-quality concentrate for the smelter market. A compact solvent extraction section effectively recovered the ammonia lixiviant for recycling to leaching and selectively transferred Cu into a conventional acid sulphate electrowinning system. High-quality "six-nines" copper cathode was produced on commercial-scale stainless steel blanks, demonstrating that the process will be able to compete effectively in the premium cathode market

Dec 1, 1995

By William D. Leech, Ronald E. Romley, Gary N. Sheppard

The Price Road Drainage Tunnel was constructed for the Arizona Department of Transportation (ADOT) in 1988 and 1989 to provide surface water drainage for the proposed outer Loop Highway (SR 117). The 5.4 km (3 mile) long, 6.6 m (22 ft) excavated diameter tunnel was driven through sand, gravel and cobbles utilizing an open face digger shield. Precast concrete segments were erected for initial ground support. A second-pass reinforced concrete final lining was placed, which was followed by contact grouting. This paper will consider the owner's representatives' view of the effectiveness of using precast concrete segments for this project. Topics discussed include segment design and erection, ground support, geotechnical instrumentation, segment erection verses contact grout interactions and tunnel production.

Jan 1, 1991

By J. Willan

This paper addresses the problem of designing a destress blasting procedure to reduce the incidence of rockbursting in hard rock mines. A review is made of the developed theory and practice of destress blasting in rockburst-prone ground. Specific reference is made to a recent survey of past and current practice with particular reference to Ontario mining operations. The need is identified for a more scientific basis for destress blast design and monitoring. Reference to developments in blasting technology as well as rock mechanics are then made to support a proposed, integrated design procedure and research strategy.

Jan 1, 1984

By Harry A. Schrecengost

The Bureau of Mines has found considerable lack of uniformity in style and content of record books used for reporting the results of examinations made by coal-mine officials. These books range from elaborate forms designed for specific examining and operating procedures at certain large mines to simple composition books, tablets, and pocket-style notebooks at other mines. Examination of thousands of these record books discloses that the reports of many examinations are so brief and so poorly worded that they cannot be understood readily. The contents, in some instances, appear to be deliberately ambiguous. The value of keeping accurate accounts of safety inspections in coal mines is often underestimated. Well-kept records reflect managerial attitude and indicate well-governed operations as well as training of official personnel to conform to considered policy and regulations and if necessary, may serve as documentary evidence to protect the mine officials and the operators.

Jan 1, 1962

By Roberto Folchi

This note deals about the controlled demolition work for the dismantling of an industrial structure in San Seplocro, Italy. The structure to be demolished, the FLOWERS SILOS, consisted in a multilevel reinforced concrete frame supporting r.c. silos and steel silos. This was standing near civil buildings and was adjoining a warehouse that had to be safeguarded for being renewed.

Jan 1, 1994

By R. Hart

In this paper, problems that have been experienced with the rockpass system at Kloof Mine No. 3 Shaft are described. Actions that have been taken to overcome the problems are also described. These include the use of slugshots to remove hang-ups, the abandonment and waste filling of passes, and design criteria adopted for an alternative pass system.

Jan 1, 2006

By Richard I. Miller

Science Applications, Inc. has developed for the U.S. Bureau of Mines a rapid response radon monitor capable of accurately responding within three minutes to changing radon levels of magnitude from 100 to 10,000 pCi/1, typical of the levels in working uranium mines. The instrument weighs 17 pounds, is sized 12" x 10" x 6", and is capable of 8 hours of continuous portable operation with a self-contained, rechargeable battery power source. Residual chamber contamination from a radon level allowed to remain in the chamber for 90 minutes is about 10 percent, decaying about a factor of two in one hour. The instrument sensitivity is a nominal 0.1 cpm/(pCi/1), with a background count rate of less than 1 cpm.

Jan 1, 1979

By J. D. Patsey, G. T. Lineberry

Introduction A computer program was developed for analyzing drum-type hoists before modifying an existing system or designing a new one. Its use permits the preliminary evaluation of a system before seeking technical assistance from mine hoist designers and manufacturers. The user-friendly program accepts a variety of data and analyzes hoisting systems for any balance state. The program can be used to calculate skip capacity to yield a desired production rate, solve for drum face width, select a permissible wire rope, estimate total horsepower of the hoist plant, and estimate annual power cost. Whether required for a large mining complex or for a relatively small operation, a hoisting system must be carefully designed to ensure the efficient, reliable, and safe flow of material. Because shaft sinking and hoist installation can total between 2.5% and 3% of the cost of opening a deep mine, proper hoist selection is critical. Today's mining engineer has at his disposal the most powerful design and analytical aid ever, the microcomputer. There is, unfortunately, limited software for the study of hoisting systems, unlike that for other materials handling equipment (Manula and Albert, 1980; Prelaz et al., 1964; Bucklen, 1969; Thompson, 1985). HOIST reduces a time-consuming set of calculations to a concise package of interrelated subprograms. A literature review revealed no common-user programs to analyze hoisting systems, although at least four major hoist designers/manufacturers/installers have their own in-house programs. To provide a tool with which the mining engineer could preliminarily analyze a materials hoisting system or could check the calculations of a hoist contractor, a computer program was developed. HOIST was written in BASIC for the IBM-PC for ease of program adaptation and to encourage field use on compatible systems. Details of program development are omitted, since the basic principles of hoisting analyses are relatively straightforward, simple, and readily accepted (Harmon, 1973; Nordberg, n.d.; Adler, 1957). Program features, intended usage, and benefits of the computerized solution are emphasized over theory development and mathematical rigor. Background The mine hoist system that is selected and installed at a mine is the "lifeline" of that mine, with installations lasting 20 years or more. Thorough study is warranted to ensure that productivity demands are met at a minimum cost per ton. The increased cost of a large, powerful, high-speed hoist must be offset by increased production to justify its selection. To optimize this tradeoff, an extensive hoisting analysis should be performed. The analyses to properly size the skip (or cage), the drum, and the hoist drive are conducive to computerization, permitting rapid evaluation of changeable operating and design parameters, such as velocity, acceleration, state of balance, and productivity demand. The program is particularly useful in conducting sensitivity trials, such as investigation into the effect of change of productivity on skip capacity and on horsepower of the hoist drive. HOIST is currently limited to the study of drum-type hoists with cylindrical drum(s). However, only minor changes to the program would permit analysis of friction hoists and conical drum configurations. Model development and testing The program is based on accepted equations and physical relationships. Examples of manual calculations formed the basis for decision points and program branching. Data is input in the order that it would be needed if the problems were solved manually. The choices are arranged likewise. HOIST was developed in sections, with manual solutions performed to check program logic. The testing became more rigorous as sections were completed. Output from one section becomes input for following sections, as appropriate. The simplified flow diagram of HOIST is given in Fig. 1.

Jan 2, 1987

By Peter L. Sheehan, David A. Fawcett, Dennis C. Martin

"Smoky River Coal Limited has successfully completed a major program involving the pattern rock anchoring of a high, steeply dipping footwall slope. The slope dips at approximately 65 to 70 degrees to the north, is benched for the upper 200 feet, is supported with rock anchors for another 240feet, and is unsupported at the pit bottom. In addition to the height and steepness, several structural features including shears, rolls and stratigraphic pinch- outs complicate footwall stability.This paper presents an overview of the project with descriptions of the engineering geology and footwall design, anchor installation, instrumentation and monitoring and a cost summary.IntroductionSmoky River Coal's mines are located in the foothills of the Rocky Mountains near Grande Cache, Alberta, approximately 200 miles west of Edmonton. The Smoky River coal leases were initially developed in the late 1960s and, except for minor shutdowns, have been in continuous operation since 1969 producing a low volatile metallurgical coal, mainly for the export market. Initial coal production was from underground mines; sur face mining started in 1971, and a large surface mine, No.9 Mine, was opened in 1974. Since that time, a number of open pits have been mined within the No.9 Mine area. Surface mining is by conventional shovel-truck method s with the use of a backhoe for mining the narrow pit bottoms.Coal recovery is mainly from the No.4 seam, which has a typical unstructured thickness of 20 feet. The most attractive opportunities for open-pit mining exist in areas of over thickening of the coal seam in the hinge zones of synclines and anticlines and in dip-slope situations. The mining of the more structurally complex pits and steeply-dipping footwall slopes requires that consideration be given to footwall stability."

Jan 1, 1988

By A Giblett, R Dunne, D Appelhans

There are a number of hurdles that must be negotiated in order to design an effective gold ore treatment facility such that the expectations forming the basis of project economics are valid and can be achieved in practice. Selecting samples based on geometallurgical context, performing and interpreting testwork relevant to the selected process flowsheet are essential considerations towards achieving this aim. This paper discusses recent experiences in process development for free milling gold ores giving consideration to frequently encountered challenges of this nature.CITATION:Giblett, A, Appelhans, D and Dunne, R, 2013. Considerations for effective gold process development, in Proceedings MetPlant 2013 , pp 445-454 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By E. O. Binyone

"https://www.youtube.com/watch?v=PBPyGXjlBHIhttps://www.youtube.com/watch?v=3AbtiKOYg7Y&feature=push-fr&attr_tag=uKtVW3yq2ZngptnE%3A6https://www.youtube.com/watch?v=PR2THayf-N8https://www.youtube.com/watch?v=mF-BXiWocqIhttps://www.youtube.com/watch?v=TuesIw-OZA4https://www.youtube.com/watch?v=v2HP7sTIZgEhttps://www.youtube.com/watch?v=v2HP7sTIZgEINTRODUCTIONIn 1937 the Eureka Corporation, Ltd., of Canada obtained a lease on the mining property of the Richmond-Euroka Mining Co. in the Eureka mining district, Eureka County, Nevada. In 1910 the Richmond-Eureka Co. suspended all operations except small-scale leasing, but company and other geologists contended that the El Dorado dolomite would also carry ore in its continuation from fault block north and northeast of the productive old working. The company began to explore the fault block in 1923 by diamond drilling from the,900 level of the Locan shaft, but for various reasons the hole was drilled to a depth of only 2 feet and was then abandoned. Eureka Corporation, Ltd., planned an extensive diamond-drilling program, which included four deep diamond-drill holes, one designated ""A"" fig. if it is to be drilled from the surfaced, and three designated ""E"", ""C"" and ""D"" figs land to be drilled from the 900 level of the Locan shaft. Of these only B and C were completed by the company. Hole C was a contribution,of the hole started by the, started by the Richmond Eureka Co. The site for hole D (figs. 1 and 2) was prepared, but the hole was not drilled. Both B and C holes penetrated sulfide ore carrying good percentages of zinc, lead, gold, and silver. The ore bodies were 40 feet thick and were found approximately 1,400 feet below the 900 level of Locan shaft.On the basis of the very favorable results obtained from the drilling program, the Eureka Corporation planned extensive development of the property and in 1942 commenced sinking the Fad shaft (figs. 1 and 2). The shortage of equipment and materials brought on by the war and difficulties with water in the shaft greatly hindered progress. However, early in 1943 the Eureka Cor¬poration, Ltd., of Canada submitted to the War Production Board a proposal for developing the mine and milling 500 tons of zinc-lead ore a day. The proposal involved an expenditure of $2,890,750."

Dec 1, 1946

By Mao Bai

In predicting the integrity of under-mined structures, surface horizontal displacements and curvatures are frequently of greater importance than the more homogeneous vertical displacements. Accurate evaluation of mining induced subsidence and horizontal displacement further requires that the predictive model adequately represents the subsurface geology, mining geometry and extraction sequencing. The following documents an extension of the Subsidence Prediction and System Identification method (SPASID) to the evaluation of horizontal strains. Comparisons are made between predictions from SPASID and two other empirical methods against measured data from a case study. The system identification method is illustrated to predict horizontal displacements and strains most consistently with the in situ data.

Jan 1, 1989

By L. D. Smith

"Those who submit competing proposals for projects seek to present senior management with complete and fully supported material that will not fail under questioning. Hopefully, misleading notions and omissions will have been minimized and there will have been testing of the assumptions regarding the economic, social and political environments. A capital project evaluation team can do management and itself a service by including a sound approach to the impact of inflation (and its twin problem, interest) on a project and a great disservice with an inappropriate approach to inflation.InflationHandled deftly, inflation can alter a project evaluation to show almost any result the handler desires. It must be a constant source of frustration for design people and cost estimators to spend weeks perfecting the technical aspects of a project in order to minimize costs, only to have all of their efforts set awash in a sea of financial and economic assumptions that submerge all of the detail. In all of this, inflation is perhaps the largest offender, with inflation criteria often being brought to bear at the last minute, almost as an afterthought. Perhaps this tardiness reflects the difficulty of the subject and the belief that senior management will take its own approach to the problems of inflation. Such a belief is unfair to senior management, for it is entitled to not being misled by omission. It is entitled to the full use of the skills of the evaluating team, including respectable assumptions of the impact of inflation.Working in a consulting context, one has the opportunity to participate in the evaluation of a large number of projects. Reflecting the observation of a wide range of views regarding the subject of inflation, this paper will-address the impact of five different approaches to inflation on the evaluation of a single Canadian mining project."

Jan 1, 1987

By John J. Vieaux

Allowable loads on Dynamically-Cast-In-Place Piles (the Franki type) can be correlated with N values from the Standard Penetration Test. Using a constant developed by Nordlund, a conservative value for load-carrying capability of a DCIP pile is developed. The DCIP pile and method of installation is briefly described.

Jan 1, 1984

By James Gibbs

In order to provide an initial approach to the deposits of oil shale, nahcolite, and dawsonite in the central area of the Piceance Creek Basin in northwestern Colorado, the U.S.B.M. and associated contractor personnel drilled and cased a 96-inch ID shaft to a depth of 2,371 feet. The shaft was constructed using "big hole" drilling techniques and succeeded in giving access to previously inaccessible deposits of the above minerals. This report documents the construction from its beginning in January 1977 to its completion in January 1978. Procedures used and problems encountered are discussed in derail.

Jan 1, 1978

By B. G. Russell

A wide range of minerals is found within the Republic of South Africa, many of which are exploited to a greater extent than in similar deposits found elsewhere. It is often asked whether this is atributed to the high grade of the ores encountered in this country, or whether such factors as fiscal and Infrastructural incentives create an economic climate that has en bled the mining industry to successfully extract and market minerals at a profit. This paper views South Africa's mineral resources in a regional and global context In an attempt to place the country's geological wealth in perspective. It represents the author's own Views, and not necessarily those of the Department of Mine al and Energy Affairs.

Jan 1, 1986

By R. W. Brigstocke

History The birth of the mining industry of Canada took place about 1670. According to Salone (Salone E., La Colonisation de la Nouvelle France, page 205) the first discovery of ore in the country was made by an iron-master, Monsieur de la Potardiere, near Trois Rivieres, Quebec. Under French rule some prospecting was done; but at this time no one seemed to consider the working of mines practicable. It was not until the time that Begon became Intendant, when the Marquis of Vaudreuil was Governor, that mining was attempted. Begon was a patron of industrial arts and did his best to promote home manufactures. The mining industry was developed under his regime and discoveries of copper and lead ores were made in 1730. About this time the St. Maurice Forges were erected to treat bog-iron ore, and they were in operation for many years. Prior to 1747, iron pans to the value of £21,000 were manufactured, together with bar-iron and plough-shares. About 1769, that is, ten years after the conquest by Wolfe, stoves and other articles, and, later, potash kettles, appeared. What is still more interesting to us-or was, at least, to General Wolfe-is that cannon balls made at the St. Maurice Forges delayed his operations. A map dated 1744, a copy of which appears in the report of the Ontario Bureau of Mines for 1913 (Vol. XIX), indicates the extensiveness of the wanderings of the French and also shows the location of the lead mine on the east shore of Lake Timiskaming. Bog-iron ore was turned into metal, with charcoal for fuel, at Norman-dale, Norfolk county, Ontario, in 1813, and at Clementsport, Nova Scotia, in 1825. In a volume published in 1672, reference is made to the occurrence of coal on the Atlantic seaboard, and in 1677 Monsieur Duchesneau, the Intendant, levied a royalty of twenty sous per ton on all coal taken from Cape Breton.

Jan 1, 1932