Search Documents

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

Jan 1, 2007

By T. Holmes

Investigations reveal that the throughput difference between a perfect production day and the average is often on the order of 40%, and that bulk solids handling system deficiencies are the largest (>50%) class of lost opportunities. Root causes for underperformance of elements in material handling systems can often be traced back to the detailed design and even study-stage oversights. To reduce or eliminate bulk solids handling problems in an existing system requires an analysis of troublesome handling equipment – for example, a concentrate transfer chute that experiences plugging, poor flow to the furnace, unacceptable dust generation, and spillage. These problems often lead to significant maintenance costs related to downtime and personnel time. Understanding the cause and cost of flow issues is the first step in troubleshooting the problem. Next, measuring the material’s flow properties is critical to providing design data required to develop a comprehensive scientific solution. In the case of a new installation, the design data is required to properly design the system right first time and prevent flow problems from occurring so that the new equipment works correctly from start-up. This paper highlights the cost of material handling problems and discusses the best approach to evaluate material handling system deficiencies. A case study is given of how Anglo American's operation in Barro Alto Brazil enjoyed a 5-month payback from a bulk solid transfer chute debottleneck project. INTRODUCTION When operating a plant or designing a greenfield or brownfield operation, the intent is to have perfect production days (PPD) each and every day. Money is made by moving material through the plant in a controlled manner to produce the desired product. Mining operations and copper concentration processes are at the most basic level a practice in bulk solids handling (BSH). Unfortunately, many of the project planning steps are overlooked, particularly related to BSH. Investigations reveal that the throughput difference between a PPD and the actual average is often on the order of 40%, and that BSH system deficiencies are the largest (>50%) class of lost opportunities (Wellwood, 2017). Root causes for underperformance of elements in material handling systems can often be traced back to the detailed design and even study-stage oversights. BSH issues are essentially baked into the fabricated plant and left to operations to accept the deficiencies and deal with them for the life of the mine. These deficiencies then become part of the normal operation of the mine and plant.

Jan 1, 2019

By John A. Johnson

For the purpose of comparing the amounts of dust produced by various mining operations, samples of atmospheric dust were collected during a complete cycle of drilling, blasting and mucking at or near the face of the Bureau's Mount Weather testing adit while the efficiency of several types of stemming in metal-mine blasting was being investigated. ACKNOWLEDGMENTS All gas samples were analyzed in the laboratory of the Bureau of Mines Gas Section at Pittsburgh, Pa.

Jan 1, 1939

By Henry C. Meeves

The Bureau of Mines, between 1956 and 1963, examined 18 major pegmatite districts in Arizona, Colorado, New Mexico, South Dakota, Utah, and Wyoming to evaluate their content of beryllium, a material in short domestic supply that has become increasingly important to modern industry. This examination report includes the salient statistics on the production of pegmatite minerals other than quartz and feldspar; and brief descriptions of 170 specific pegmatite deposits.

Jan 1, 1966

By Richard E. Gray

Subsidence due to coal mining is poorly understood by non-specialists. This has led to numerous misconceptions and myths based on limited observations and lack of knowledge. The three most common are: 1. Mine maps are inaccurate. 2. Deep mines are not a problem. 3. If no subsidence has occurred for many years after mining, there is no risk of future subsidence. Maps are important during mining and most are carefully prepared. Future use to evaluate conditions at mine level often includes drilling to confirm what the map shows. Usually, little or no effort is made to tie the surface survey of the property to the mine survey, to conduct a well designed drilling program to confirm the mine map, or to drill test borings vertically. When a mine entry is encountered rather than a coal pillar, or vice versa, and conditions at mine level appear different than anticipated, the first reaction is the mine map is inaccurate. The idea of a safe depth from subsidence is often based on the false premise that mining results in sufficient breakup of the overlying rock strata that bulking compensates for the coal extracted. The safe depth idea first appeared in the literature about 1880 and remained prevalent well into this century. Sadly, it is still encountered. The modern understanding of fragmentation of the immediate mine roof with the overlying beds sagging down on the broken roof rock was first described in 1900. With full extraction mining, either longwall or retreat room and pillar, surface subsidence occurs regardless of the depth of the mine. Subsidence over longwall mines at depths of 2000 feet can be 90 percent of the mined seam thickness. Numerous studies of undermined sites conclude that mining occurred many years ago and since no subsidence has occurred, there is no risk of future movement. This is true if sufficient coal pillars have been left to support the overlying strata. However, every year subsidence occurs over mines that have been closed for 100 years or more. In a study of subsidence incidents over the Pittsburgh Coal, the senior authors found that 50 percent of the incidents occurred above mines that had been closed for at least 50 years and 10 percent over mines closed for at least 80 years.

Jan 1, 1996

By Gregory R. Gorrell

The legal issues surrounding the regulation of subsidence are among the major concerns facing the underground mining industry today. Whether subsidence occurs almost immediately as a result of longwall mining or without warning as a result of room and pillar mining conducted years ago, the resulting disputes are highly controversial and typical of the disputes involving the competing interests of surface and mineral estate owners. Until recently, the law governing these disputes was firmly established under the common law. The passage of the Surface Mining Control and Reclamation Act 1, the utilization of new mining technologies, and the general heightened environmental awareness of our times, however, have interjected new issues into this area of the law. State and Federal court decisions and administrative agency interpretations have helped clarify some of the issues. However, as evidenced by the many recent lawsuits between operators, surface owners, and regulatory agencies, many uncertainties still exist.

Jan 1, 1986

By John C. Machisak

INJURY experience and employment data at all metal mines in the United States and Alaska are presented in this Information Circular for the calendar year 1958. This publication covers the metal mining industries, and contains statistical data on injuries and employment pertinent to metal mines, ore-dressing plants, and primary nonferrous smelters, refineries, and reduction plants. These operations report injury and employment information annually to the Bureau of Mines on a voluntary basis. The Bureau is authorized to make requests for such data, and the information submitted contributes immeasurably to the promotion of safety in the metal mining industry. Every effort has been made to make the annual canvass as complete as possible. This publication contains, along with production and development workers, the office employees at the mine location. The metal mines identified in this publication are classified according to the mineral ores mined; that is, copper, iron, lead-zinc, gold-silver lode, gold placer, and miscellaneous metals.

Jan 1, 1962

By Michael S. Miller

In 1987 and 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 3,100-acre Borah Peak Wilderness Study Area (10-047-004) and a 708-acre parcel adjacent to the north in order to evaluate their identified mineral resources. The study area is located in Custer County, ID, about 18 mi northwest from MacKay. The study area lies along the western foothills of the Lost River Range and is underlain by quartzite, sandstone, shale, argillite, dolostone, and limestone. The Lost River fault, a major active fault, lies along the length of the study area. Large alluvial fans spread out from valleys originating east of the study area.

Jan 1, 1989

By C. E. Wood

[Because of the renewed i~,ortanc of the strate ic netal ~ngane8e the Bureau of Mines is conductin further ro~aarch on pyrometallurgica1 ~ethods of boneficiating 0 ngani.foro'l iron ores nnn lo\,f-~~r de oanganesc ores. Published data on .the l2~roI'let llurgica.l treatnent of tl::1.nganse8 ores have been revi .. \-'en by Jose-ph ? .2]

Jan 1, 1940

By C. E. Wood

Because of the renewed importance of the strategic metal manganese the Bureau of Mines in conducting further research on pyrometallurgical methods of beneficiating manganiferous iron ores and low-grade manganese ores. Published data on the Pyrometallurgical of manganese ores have been reviewed by Joseph.5/ A method of treatment that has received less consideration than others is the matte smelting of manganese or the separation of manganese from the iron and the gangue in an ore b, formation of a matte, that consists principally of esulfide of manganese. A procedure of this type has been patented by Betts.6/ Lofquist7/ claims advantages for the production of a sulfide-oxide matte as a method of recovering manganese in alloys containing manganese and iron.

Jan 1, 1940

By D. L. Paulson

The Bureau of Mines is investigating pyrometallurgical and chemical methods for extracting copper from sulfide ores under conditions that provide for control of gaseous and solid emissions. Under this program, a new electrothermic reduction process was developed to produce blister copper after collecting essentially all of the sulfur by a single-unit operation. The process feasibility was indicated by a laboratory-scale investigation that demonstrated chalcopyrite concentrate can be roasted to less than 1 percent sulfur and that the resulting calcine can be reduced with carbon to blister copper by a cyclic process in a single arc-smelting furnace. Pilot-scale tests in an 800-kV-A electric-arc furnace demonstrated that 98.4 pct of the contained copper can be continuously recovered as metal by operating at bath temperatures between 1,350° and 1,375° C. Smelting rates of approximately 225 lb of blend ft2 of bath surface/hr resulted in power consumptions of approximately 520 kW-hr/ton of blend. The blister copper that was produced contained less than 0.1 pct iron while the precious metals reporting to the copper product and gangue material elimination were similar to those in a conventional smelting operation.

Jan 1, 1976

By Walter E. Pittman

In its role of providing technical assistance to the mining industry, the Bureau of Mines' Tuscaloosa Research Center has conducted research to develop trapped miner location systems which would aid in locating miners trapped by underground mining disasters. Efforts to produce electromagnetic systems for the location of trapped miners underground and to communicate with them were surveyed, from the 1920's to 1981. Theoretical studies of through-the-earth electromagnetic transmissions are described as well as studies of the electrical characteristics of various rocks, minerals, and soil. Several trapped miner location systems are reviewed including the Westinghouse systems, the DEVELCO system, and an automated three-dimensional location system, and the phase difference of arrival technique. Tangential research, relevant to trapped miner location systems is described. A comprehensive bibliography covering all aspects of trapped miner, through-the-earth electromagnetic location and communications systems is appended.

Jan 1, 1982

By William M. Hinton

This report describes the approach, procedures, and results of a program to develop training materials for roof bolter operators. The objective of the program was to design and produce a training sequence which would prepare roof bolter trainees for job performance. Data was collected and analyzed using the general procedures of Instructional Systems Development (ISD). Input data came from a previous roof bolter training analysis program. This data was expanded and structured through a series of ISD steps: objectives hierarchies, media selection, syllabus, lesson specifications, and train¬ing materials development. The resulting program consisted of an ordered sequence of 15 lessons. The media mix for the 15 lessons included lectures, slide-tape lessons, and hands-on instruction using operational roof bolters. Contents of all lessons were reviewed and approved by the Bureau. The key recommendations were to (1) validate the materials and measure relative effectiveness of media formats; (2) survey mines for training resources and conditions - match materials to user capabilities, rather than selection state of the art technology/media; (3) develop job performance aids (JPAs) rather than simulators; (4) create a style/media/JPA development guide for use in future projects of this kind.

Jan 1, 1982

By J. G. Price

"The paper reviews state-of-the art welding processes and consumables for structural and pressure equipment applications in offshore environments, particularly the Arctic. Optimum selection of consumables will be discussed with regard to the facility to meet tentative toughness requirements in weldments. Finally, the development of welding procedure specifications will be considered in relation to the prevention of hot or cold cracking and lamellar tearing.Welding RequirementsGeneralThe exploitation of Canadian frontier oil and gas reserves will require a fleet of various types of offshore structures. These will include fixed jacket types and semi-submersibles for the East Coast with huge man-made islands and icebreakers for the Arctic regions. Both these regions will also require supply and drill ships plus subsea pipelines and cargo tankers for transportation. Clearly the welding of these items will plays large part in the over-all integrity and safety of exploration and production operations.The required development in structural steels and pressure vessel steels, for current and future offshore structures, to improve properties, particularly toughness for lower temperature service, has also prompted welding researchers to develop process and consumable combinations to match the parent plate specifications. This development has had to consider particular aspects of weldability such as a low susceptibility to cold cracking and preventing low HAZ toughness. Current research has centred on attempts to increase HAZ toughness with higher heat input welding of newly developed structural steels.The installation of Arctic region pipelines has provided a sound base for future, more complex fabrications in the most severe service temperatures in the Canadian frontier although few of the installations have been designed to the lowest possible exposed temperature of -62°C."

Jan 1, 1987

By B. J. Breen, C. S. Mogg

Considerable borehole investigation work has been completed at a proposed site at Sellafield in Cumbria, supplemented by seismic surveys, other geophysical sensing and geological mapping. The focussing of investigation on the rock mass itself will be achieved by means of the planned underground rock characterisation facility, giving access to depths of about 800 m in the strong, low-permeability basement rocks of the Borrowdale Volcanic Group. Characterisation work undertaken during the sinking phase and interaction with continuing surface-based exploration and monitoring should permit a firmer assessment of the long-term safety of a repository. Key considerations in the choice of a design for the repository include the waste handling method, underground inlet cell, underground vaults, vault environment and environmental effects

Aug 1, 1994

By Paramguru R. K, Jena P. K

Increasing demand for copper, lead and zinc with continuous depletion of good grade ore reserves, warrants the need for utilization of lean and complex ores of these metals. There is worldwide effort to develop suitable processes for these purposes. The present paper deals with the chloride leaching of complex base metal sulphide concentrates of two Indian deposits. A two stage leaching process is suggested keeping selectivity of metal dissolution in view.In the first stage most of the lead and zinc are reacted with dilute FeCI3 (0.3M) solutions at a temperature ono°c where major portion of the lead remains in the residue and zinc reports in solution. After taking out lead chloride by brine leaching, the residue has been treated for copper dissolution. A concentrated FeCI3 leaching at boiling temperature as well as ambient aqueous chlorine leaching have been separately tried to dissolve out the copper from the residue. Based on the results obtained, a flowsheet for the proposed process is presented.

Jan 1, 1981

By Patrick J. Doig

The contract for the construction of the Inline Pump Station for the Milwaukee Metropolitan Sewerage District involves the sinking of three shafts and the excavation of a pump chamber. The shafts are being sunk to a depth of 104 meters and pass through 52m of sediments before encountering dolomitic bedrock. The pump chamber is constructed in dolomite. The sediments are alluvial, estuarine and lacustrine in origin, with some ice margin deposits. They comprise loosely consolidated fine to coarse grained sand, silts, clays and gravels, and they are heavily saturated with a water content often above 60%. The water table is at a depth of 3m. The dolomite is silurian, generally dense, with some clay-filled vugs and shale partings. Until 1983, underground construction in the Milwaukee area had been limited to depths of 26m in the sediments and 20m in the dolomites. Water control methods had included caissons, compressed air, extensive internal and external dewatering, and grouting. Flows of 20 liters per second were commonplace with as much as 80 liters per second being encountered in the rock. However, in 1984 work was commenced on the deep sections of the Milwaukee sewerage scheme with the letting of three major contracts including the Inline Pump Station. With excavation taking place at greater depths, it become obvious that previous methods of water control would be inappropriate. To protect against major inrushes of high pressure water in the rock, an extensive program of pre-grouting from the surface was specified. Water control in the sediments was left to the discretion of the contractor and in each case freezing was choosen. This paper describes in detail the grouting and freezing procedures.

Jan 1, 1985

By G. W. Jones

In a previous report,6 results were given that showed the amount of natural ventilation in a manhole having a capacity of 74.l cubic feet when the number of ventilation openings in the cover was varied. from no openings to a maximum of 48. The results showed that the ventilation (air changes per day) in the manhole was proportional to the area of the openings in the cover, and also that the number or area of the openings was the factor that chiefly affected the ventilation.

Jan 1, 1937

By D. R. Dance

The Resonant, or as it has more commonly come to be known the 'Sonic' Pile Driver, dates back to the early 1960's, when prototypes were produced by Charlie Guild, of Providence, Rhode Island, and A1 Bodine of Los Angeles, California, these were later to be developed into the unit known as the BRD 1000. Based on this initial work, the Shell Oil Companies of Sonico and The Resonant Pile Corporation, produced and operated 30 of these BRD 1000 machines, which were used throughout the U.S.A. and Canada on a wide range of foundation projects. Subsequent to this, Raymond International and G K N, of England, operated units on programs; the G K N units being of slightly modified configuration. In 1973 Hawker Siddeley Canada Ltd., acquired the license for the Pile Driver and related systems with the intent of promoting the use of the machines to install support pilings on the Alyaska Pipeline Project, but this did not materialize due to problems with the oscillator. After radical redesign and field testing of the oscillator system the unit was employed on a number of test projects principally in Northern Canada and Alaska.

Jan 1, 1987

By Joel Nonnweiler, Rafael Castro, Ross Webb

The three thousand foot long 66-inch diameter Folsom East Interceptor Section2B was completed accident free, on time and under budget with no measurable surface settlement. The tunnel passed through nested cobbles, highly abrasive sands and gravels, and abandoned mine workings with less than five-feet of cover at times. Preventing settlement was critical since the tunnel passed under a heavily traveled state highway. A pilot project to test microtunneling and pipejacking methods in the same ground conditions abandoned both drives before completing the planned drive lengths. This paper discusses performance of the conventional tunneling method selected to excavate the ground and the effectiveness of the ground modification techniques employed.

Jan 1, 2001