Search Documents

By Gregg Hodges, Fred Schoenbrunn, Steve Slottee, Chad McCleary

"In December, 1999 Stillwater Mining Company (SMC) commissioned a new paste /cement backfill plant to supplement the existing sand backfill system for the cut and fill mining operation at it’s Nye, Montana mine. The new plant uses the Baker Process Deep Cone TM Paste Thickener to thicken the total concentrator tailings from 30% solids slurry to a 71% solids paste. This paper describes both general paste formation concepts and the evolution of the SMC paste plant operation from original design criteria, through problem solving and plant modifications, to the operation of the existing plant.Although the original process design was not effective for consistently producing and delivering acceptable paste to the stopes for backfill, SMC was able to make the mechanical and process modifications which allow the plant to now produce and deliver an acceptable product to the stopes. Ongoing test work is targeted at increasing the pumping range of the system, increasing the paste solids concentration from the Deep Cone Paste Thickener and reducing the operating and maintenance costs of the system.INTRODUCTIONThe authors would like to thank both Stillwater Mining Company (SMC) and Baker Process for their assistance in the preparation of this paper. Stillwater Mining Company chose not to participate directly in this paper due to time constraints, but was very helpful in answering questions concerning their approach to problem solving and specific details with regard to engineering criteria.This paper will begin with a general review of the technical and mechanical concepts in paste formation and then focus on the overall design, start-up and problem solving process for the paste backfill operation at SMC’s mine and concentrator near Nye, Montana."

Jan 1, 2001

By D P. Sainsbury, B L. Sainsbury, A Vakili, H-D Paetzold, P Lourens

The cave propagation behaviour of a jointed rock mass is strongly governed by the unique nature of joints and discontinuities, together with the intact strength of rock bridges that make up the rock fabric. A discrete finite difference (DFD) modelling technique has been developed to allow for the detailed consideration of the rock mass structural fabric at many scales and through many different stress paths that can be used for complex mine-scale analysis. The DFD methodology uses interfaces to explicitly represent large-scale structures and ubiquitous joints embedded within the simulated rock mass matrix to characterise intermediate structures. Through simulated testing of DFD materials, properties such as strength anisotropy and scale effects can be obtained. This paper discusses the successful application of implementing a DFD modelling technique for the back-analysis of caving-induced subsidence behaviour of Lift 1 at the Palabora mine.CITATION:Sainsbury, D P, Sainsbury, B L, Paetzold, H-D, Lourens, P and Vakili, A, 2016. Caving-induced subsidence behaviour of Lift 1 at the Palabora block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 415–426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By E. S. Leaver

The gold that is not recovered by a particular process is refractory to that process. A study to determine how the refractory gold is associated in the ore constituents usually indicates the needed improvement in the process or additional methods for bettering recovery. In preliminary work, segregation of the various minerals, gangue or impurities, and data showing the reactions of each in the recovery method readily confines the refractory gold to a certain part on which extensive research can be directed. In this dissecting plan, the microscope is an important aid in locating the refractory gold but should be supplemented by chemical tests.

Jan 1, 1934

By Alejandro Ferrada Vergara

Most blasting techniques that are designed to improve fragmentation and subsequently improve ore work index to downstream comminution processes, apply powder or energy factor increases, either by stretching the drilling pattern (burden/spacing ratio) implementing faster initiation sequences or using more energetic explosives. The new application will move detonation parameters up, making the blasting process riskier for the surrounding boreholes, explosive column or initiation systems functioning.

Jan 1, 2016

By D. M. A. Flight, P. M. Green, J. A. Plant, P. R. Simpson

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The British Geological Survey's regional geochemical database is used to identify the patterns associated with the various mineral deposit types and to examine the extent to which their distribution reflects the presence of long-lived metallogenic provinces in the crust. Image analysis provides new insights into the setting of the mineralisation, geochemical constraints on tectonic models of Caledonide evolution and evidence for terrane amalgamation and large-scale processes. There is evidence that much of the mineralisation reflects the presence of long-lived provinces with a distinctive geochemistry reflecting their origins as zones of crustal extension. In the case of the Middle-Upper Dalradiam sedex deposits, the relationship between geochemistry and tectonic setting is direct. In other cases, rocks deposited in extensional zones appear to have acted as reservoirs of ore-forming elements which were further concentrated during later events

Jun 19, 1905

By P. Toscano

The objective of this investigation was to determine how the losses of nickel, copper and cobalt in fayalite slags could be controlled for nickel mattes with iron contents below 5 wt%. Laboratory-converting and slag-cleaning experiments were carried out at 1250°C. Several variables were investigated during and after converting to help minimize the amount of nickel and cobalt that reports to the slag. The variables used were oxygen concentration in the blast, coke breeze addition and nitrogen injection stirring. In all the experiments, slag and matte co-existed. Coke additions during converting have little effect on the losses of nickel, copper and cobalt. In fact, coke additions retard the converting process by consuming some of the oxygen injected. On the other hand, coke additions and nitrogen injection applied after converting was completed resulted in decreased slag losses.

Jan 1, 2004

By P. Toscano, T. A. Utigard

"The objective of this investigation was to determine how the losses of nickel, copper and cobalt in fayalite slags could be controlled for nickel mattes with iron contents below 5 wt%. Laboratory-converting and slag-cleaning experiments were carried out at 1250°C.Several variables were investigated during and after converting to help minimize the amount of nickel and cobalt that reports to the slag. The variables used were oxygen concentration in the blast, coke breeze addition and nitrogen injection stirring. In all the experiments, slag and matte co-existed.Coke additions during converting have little effect on the losses of nickel, copper and cobalt. In fact, coke additions retard the converting process by consuming some of the oxygen injected. On the other hand, coke additions and nitrogen injection applied after converting was completed resulted in decreased slag losses."

Jan 1, 2004

A shortage of technical skills in all areas of the mining industry is being experienced worldwide. This has significant consequences for design, operations, productivity and safety and, therefore, needs to be seriously addressed, both in the short and longer term. It is therefore both a strategic and a tactical issue. Importantly, however, since mining is a long-term business, the shortage of skills must be dealt with from a strategic point of view to ensure the supply of the necessary skills for future mining. This paper will deal specifically with the provision of high level technical skills, that is, university graduates in mining engineering, and the outlook for the institutions that are currently producing such graduates.

Jan 1, 2008

By L. M. Anisdahl

Ventiflex is a flexible ventilation duct system with a global market within mine and tunnel ventilation. The system is distributed in a wide range of qualities and dimensions. It is very important that ventilation systems are designed correctly in mines and tunnels. An incorrectly dimensioned system might result in bad air quality and too high costs. The objective of this study has been to assess some important design parameters for ventiflex comprising the friction loss factor for the duct wall itself, as well as the shock loss factors and the leakage factors for the different couplings systems. This has been obtained by carrying out a large scale experimental program on ducts with all the three different couplings: Velcro, zip and steel-ring. Pressure profiles and air flow rates have been measured, and based on these data the different factors have been calculated. The following results have been obtained: A friction factor l = 0,012 (K = 10) for the duct wall, a shock loss factor z = 0,0125 for velcro- and zip couplings, a shock loss factor z = 0,005 for steel-ring couplings, and a leakage factor f* = 0 mm2/m2 for all three coupling types. The latter result proves that no leakage is possible for a correctly installed duct with proper alignment. The results also confirm that ventiflex complies with class S, or better, according to the SIA-norm. However, whether ventiflex should be designed as class S, A or B according to the SIA-norm, depends on the particular application.

Jan 1, 2009

By David B. Doan

This regional report covers 1993 mining and related activity in approximately 40 countries and territories of Canada, Latin America, and the Caribbean Basin. These countries of the Western Hemisphere, as with the United States, are endowed with a great variety of minerals, including metals, industrial minerals, and energy minerals. For most of these countries, such mineral production helps form foundations for their economies and earns export credits including hard currencies. Table 1 depicts an overall view of Latin America and Canada's production of its major mineral commodities in 1993; subsequent tables show the role of Latin America and Canada in world mineral production, trade, and import dependency on minerals from Latin America and Canada by the United States. Overall, the picture emerges of a rich mineral diversity throughout the hemisphere, attracting increasing interest and investment, and complementing the mineral resources of the United States.

Jan 1, 1995

By W. C. Peters, M. W. Pullen, C. A. Bays

During the past three and a half years considerable improvement in the techniques of solution extraction of salt has been made by the use of wells which are cross-connected by hydraulic fracture at the base of the salt. Fracture is initiated by the application of hydraulic pressure. Underreaming and perforating techniques are used to control initiation. The fracture is then extended by continuous pumping until a pressure communication is obtained. Pressure communication is followed by washing-through to obtain a low-pressure connection. Well construction using non-shrinking cements that will bond with the salt and with associated strata is essential to the process. The connecting procedure described permits solution to attack the salt deposit from its base upward, thereby permitting greater recovery, fewer well repairs, better saturation of brine, and overall economy of development and operation. The fracture method of cross-connection requires special pumping of the fluid and is limited by present experience to initial well spacings up to about 1200 feet. The method has been used in bedded salts and is applicable for wells in salt domes. Since spring of 1956, new developnents in salt extraction wells have followed procedures substantially different from those in prior use. Although multiple well systems, connected either by the natural consequence of the solution process or by undercutting under protective pads, have been used previously, the past three and a half years have brought about new designs and new operation procedures based on cross-connection of the wells using hydraulic fracture. To date these techniques have been applied largely in the bedded salt deposits of Michigan, Ontario, Ohio, West Virginia, and New York. To the writers' knowledge they have not been used in salt dome wells. The methods have not yet been in use for a sufficient period to permit any statistical comparison with the older methods. It is evident from experience to date that the methods result in higher recoveries, lower capital and operating costs, better saturation of produced brine, reduced well maintenance and repair, and in considerably fewer production units to insure

Jan 1, 1961

By R. Raghavaraju

Estimation of the dynamic stress field in terms of its amplitude and decay around a blast hole is a key input parameter in all numerical modeling and blast prediction exercises. However, there is very limited information available in literature on these critical parameters, which would be considered essential in any blast modeling exercise. A laboratory-scale experimental study has been carried out in two different rock types to study at very close range the stress wave decay from a blast hole at distances ranging from 3 to 10 borehole radii. The single–hole blasting experiments employed a centrally located detonating cord (5.3 g/m) in 6 mm(1/4 inch) and 10 mm (3/8 inch) boreholes. The coupling medium employed was air and water, in addition to using a thin-walled copper tube in intimate contact with borehole wall to prevent of penetration of explosion gases into the emerging cracks. The paper describes the nature (amplitude and decay) of the transmitted shock pressure and their evolution in the two rock types for these various experimental conditions, which are present to varying degrees in all blasting operations.

Jan 1, 2014

By K. Duckworth

"Comparative tests of the conventional Turam survey configuration and an alternative configuration called the Tx-parallel configuration were conducted at the McClean uranium deposit in northern Saskatchewan. Both configurations detected the known conductors at the site but the alternative configuration demonstrated its particular effectiveness in the reconnaissance role. This effectiveness results from the fact that the length of Tx-parallel traversesis controlled only by the length ofthe transmitter and not by its power. In addition, the field strength along a Tx-parallel traverse is uniform unless the traverse approaches the end of the transmitter. This freedom from a strong gradient of the primary field along a Tx-parallel traverse eliminates the gradient-induced anomaly shifts which are common in conventional Turam operations. The locations of each of the McClean conductors, that were obtained from the Tx-parallel profiles, werein better agreement with the locations known from drilling than were the locations obtained from the conventional profiles. However, the conventional profiles gave better estimates of the conductance of the targets.The results obtained over the McClean conductors indicate that current gathering has a strong influence on Tx-parallel results with consequent unpredictable influence on depth and conductance estimates. However, the depth estimates obtained from the Tx-parallel data appear to be in good agreement with the known depth of the McClean south conductor. The Txparallel results provide shallow estimates of the depth of the McClean north conductor which suggest that the fracture zone above the graphitic conductor is a significant conductor as was also suggested by earlier VLF surveys.Comparison with the wide range of published geophysical test surveys for the McClean site showed that apart from the work required to lay the transmitter, the Tx-parallel mode of operation of a Turam exploration system is operationally very similar to a moving source Slingram type of survey. At the McClean test site, it provided the same depth of exploration as a conventionally deployed fixed loop transmitter."

Jan 1, 1988

By David S. Bowling

The ER-300 Series White Recorders were developed to provide on economical, yet invaluable instrument for those who desire permanent recordings of such data OS displacement, vibration, concussion (air borne effect) and velocity information. The precise monitoring of earth displacements and air blast magnitudes aids quarrymen and construction contractors in estimating safe blasting limits when operating in populated areas. A refraction model is available for recording velocities which permit the determination of weathered zone depths as well as the .depths to other subsurface formations. The dual purpose (Refroction- Displacement) systems ore utilized for velocity studies and displacement - oir blast measurements.

Jan 1, 1990

By Moi Arzamendi, Jose Ramirez, Kenneth Kniss, Sunil Arora, James Gingery

Construction of a new approach embankment for a railroad bridge over a river in Southern California required placing up to 12 ft of fill over soft to medium stiff silts and clays along an approximate 1,500-ft long stretch. The embankment, situated within a narrow railroad right-of-way between an existing live track and existing buildings, would have been susceptible to excessive settlement that could damage existing buildings and numerous underground utilities if regular weight soil fill had been placed over the unimproved ground. To limit total and differential static settlements to tolerable levels, a design was developed using a combination of mechanically stabilized earth wall with lightweight cellular concrete fill and rigid inclusions ground improvement. This paper describes the design of the ground improvement system, construction methods used, and challenges of working next to live railroad traffic. Ground improvement quality control and assurance measures, and verification of performance by settlement monitoring are also addressed. INTRODUCTION AND BACKGROUND The 0.9-mile San Diego River Double Track (SDRDT) project is located on the Los Angeles-San Diego- San Luis Obispo (LOSSAN) Corridor in San Diego, California. The project includes the replacement of the existing 900-ft long single track railroad bridge over the San Diego River with twin double track structures. Construction of the project is phased and closely coordinated with the associated Mid-Coast light rail project (San Diego Trolley Blue Line Extension). The new bridge is a 7-span, twin steel, through girder structure supported by six cast-in-place reinforced concrete pier caps and two abutments. The large diameter cast-in-drilled-hole (CIDH) foundations are up to 9 ft in diameter, with upper portions encased in a 1.5-in.-thick permanent steel casing. The north abutment approach embankment includes a mechanically stabilized earth (MSE) retaining wall up to approximately 10 ft high and 1,520 ft long. This paper focuses on the design and construction of the north approach embankment. The project site is characterized by challenging geotechnical and seismic conditions. The site contains liquefiable soils interbedded with soft cohesive soils, underlain by competent layers of sand/gravel/cobble and other sedimentary formations. Static settlement of the new railroad, crossing utilities and adjacent buildings was a primary design concern for the north approach embankment.

Jan 1, 2018

By J. F. Reddick

The South African coal mining industry is currently disposing of about 10 million tons of ultra-fine coal (<150 µm) per year. Once discarded, these sulphur-containing ultra-fines contribute to several environmental problems. As part of a project initiated by the Water Research Commission to investigate the use of Cleaner Production (CP) in the mining industry, a study was carried out to determine whether a CP approach could be used to identify opportunities to reduce this coal waste, and to determine which of these opportunities would be most feasible. In order to do this, a CP assessment was conducted at three case study collieries in the South African Witbank coalfield. Mass-balancing and sampling, followed by laboratory characterisation tests and site surveys, were used to determine the quantity, quality and sources of the ultra-fine coal at the three collieries. Literature reviews, brainstorming sessions and interviews then followed to generate the CP options. An environ-mental, economic and technical feasibility assessment was then prepared for each option, to determine the most viable interventions for implementation. A number of opportunities were identified through the assessment. By preventing coarser coal from being discarded with the ultra-fine coal, the quantity of coal disposed of could be decreased at all three collieries, and by up to 24% in one case. Increasing the crusher top size would reduce the amount of coal that is milled to less than 150 µm, so that less is wasted. The ultra-fines that have already been disposed of on slurry dams can be completely reclaimed and converted into a valuable product, which can be sold as power station feedstock. The newly processed ultra-fines could be beneficiated using flotation and exported together with the coarser coal. The results of the assessments thus suggested that workable CP opportunities to reduce ultra-fine coal wastage exist at the sites investigated, and that their feasibility is colliery-specific. The associated financial benefits of the proposed options suggested that CP is a realistic approach to addressing environmental problems. Keywords: Cleaner Production; coal mining; coal-washing; ultra-fines

Jan 1, 2007

By S. Sarac

In this study, graphical and mathematical methods used to determine operating points in single or multiple fan ventilation systems are summarized. The problem is mathematically formulized for parallel connected fans in which analytical solutions are not possible. For n number of parallel connected fans, a non-linear equation system that consists of n number of non-linear equation sis derived. The Newton-Raphson method, which is a numerical analysis method, is adapted to solve this non-linear equation system and the solution steps are given as an algorithm. A computer program based on this algorithm is written and its applicability is proved.

Jan 1, 2000

By John P. Borovsky

A 3-year study was conducted to evaluate the problems and benefits of using vegetation to stabilize tailing from a potential Minnesota copper-nickel milling operation. The project consisted of three separate investigations: a waste characterization study, a greenhouse study and a field study. With few exceptions, the physical and chemical characteristics of the tai ling were found to lie within the range of properties of Minnesota soils. The tailing lacks organic matter; is deficient in nitrogen, phosphorus and potassium; and may contain elevated levels of soluble salts and heavy metals, particularly copper and nickel. Numerous grasses, forbs and woody plants will tolerate the tailing as a rooting medium. Peat incorporation and topsoil dressing provided few benefits to the revegetation process which were not provided by a fertilizer application. With fertilization, grass/legume production in the tailing was comparable to local agricultural yields. Concentration of heavy metals in grasses grown in the tailing were generally below suggested tolerance limits for plants and animal forage. Legumes tended to accumulate higher concentrations of copper and nickel, and metal uptake of most plants was positively correlated with rate of fertilization. Tailing drainage water contained elevated levels of heavy metals, and establishment of vegetation had little effect on the quantity and quality of tailing drainage water. However, topsoil dressing significantly increased drainage water volume when compared to unvegetated control plots. Copper-nickel tailing revegetation recommendations were developed.

Jan 1, 1983

The mining licence for the Macraes gold mine places emphasis on the progressive rehabilitation of the land to a state compatible with the landscape and environment that existed prior to mining activities taking place. The shallow soils and hostility of the environment dictate that choices of plant species should focus on persistence rather than high productivity, choices that are made easier by observing the vegetation patterns that have developed naturally within the area, by recontouring landforms to integrate with the surrounding countryside and the use of appropriate plants and establishment techniques.

Jan 1, 1992

By M. K. Larson

The U.S. Bureau of Mines conducted a study to evaluate support interaction between conventional bolts and the rib at two Western coal mines. The principal goal was to develop guidelines for designing rib support under various conditions. At mine A, seven rib bolts were installed with load cells and monitored over a 4-month period. Fifty-seven pull tests were conducted with two types of anchors at various depths. At mine B, 163 pull tests were conducted. Results showed that during the 4 months of monitoring bolt load, tension in the bolts decreased over time in some situations and that anchorage capacity was reduced in a yielded zone. Load-versus-deformation plots from pull tests in the rib showed fundamental differences in anchorage behavior at the two mines, particularly when comparing results of tests in old pillars at mine A and tests in new ribs at mine B. Numerical modeling experiments indicate that coal bonding strength was the most significant factor in determining postyield anchorage capacity. Correlation of anchor yield point with anchor depth were more pronounced at mine A than at mine B; measuring torque may be a reasonable method of monitoring deteriorating anchorage capacity in a rib undergoing fracturing and yield.

Jan 1, 1996