Search Documents

By Priscilla P. Nelson

Many concepts concerning equipment selection, performance prediction, and evaluation of support requirements for tunnel construction in soil or hard rock tunnels cannot be extrapolated directly for application in soft rock (compressive strength between 1.0 and 35.0 MPa). Case histories for small diameter (less than 3.5 m) tunnels in Austin, Texas, are analyzed to gain insight into particular problems encountered during tunnel excavation in weak sedimentary rock, and the performance of different excavation systems are compared.

Jan 1, 1987

By James A. Finch, Stéphanie Somot

"The self-heating facility developed at the Noranda Technology Centre [Rosenblum and coworkers, 2001; 1995] has now been established in the Department of Mining, Metals and Materials Engineering at McGill University. A research program into mechanisms has been initiated (with support now from four industrial partners under Camiro). The first investigation is into the role of pyrrhotite (Po), the most commonly suspected mineral to trigger self-heating. Following a standard experimental protocol, self-heating was assessed on samples of Po mixed with sand as an inert material. With increasing Po content, self heating progressively increased but, interestingly, the samples visually appeared less and less oxidized. A high Po content, it was hypothesized, may give a more reducing environment favouring formation of H2S. The presence of this gas could be significant as it has a high exothermic heat of reaction with oxygen. The system was modified to test the hypothesis by including copper pieces and copper sulphate to react with (and therefore reveal) the gas as copper sulphide. Evidence is presented in support of H2S production, which to our knowledge has not been shown before and introduces a potentially important avenue of investigation into self-heating mechanisms.INTRODUCTIONSelf-heating of sulphide minerals poses potential environmental and safety hazards in mining of ores, and storage and transport of concentrates. While some conditions are known to be critical, the reactions remain poorly understood making self-heating difficult to predict and control.A major advance in measurement was introduced by Rosenblum and co-workers [Rosenblum et al., 2001; Rosenblum and Spira 1995]. A self-heating assessment method was developed and applied to various sulphide-bearing materials The method is based upon automated calorimetric cells with data acquisition, now available to McGill researchers and which have been used for the study reported here."

Jan 1, 2006

By Rodrigo Toro, Ivan Yutronic N

"The Copper Concentrator Plant of Compañía Minera Doña Inés de Collahuasi (CMDIC) is composed of three grinding lines, the third one being the largest. Due to the capacity feature of the third line, specially its SAG mill, it is a priority that the advanced process control team of the Company deploys a supervisory control strategy that allows this unit to operate in an optimal way, in order to achieve the maximum productivity at minimum cost. It is in this kind of tasks where advanced control applications play a key role in obtaining the best economic profit of the process.The advanced process control team, formed by people from Informatics, Automation and Operations of CMDIC have assumed the challenge of generating the transition from a manual SAG Mill 1011 operation (40 x 22 feet, the largest copper SAG mill of the world), to a fully automatic SAG Mill using a multivariable control strategy instead of a rule based on expert control system (widely used in industrial mining process control applications).Therefore, CMDIC decided to work together with Honeywell APC Team implementing an advanced automatic control strategy for the SAG Mill 1011, using for this purpose a technology called Model Based Predictive Control (MPC), based on a variety of control methods that uses dynamical models of the process, obtained from input/output data, in order to print the process knowledge into a group of mathematical relationships that links the constraints (controlled variables) with available commands (manipulated variables) and measured disturbances.The main objective of the advanced control strategy is to ensure process government, tending to throughput stability and optimization, by the execution of coordinated control actions, proactively avoiding measured disturbances effects and the SAG mill overloading.The most important benefits of using a multivariable control strategy are: the automated operation of SAG mill 1011 (that was manually operated before the implementation of this application), a safer, more coordinated and more stable process operation, achieving through this an increase of throughput and a decrease of specific energy consumption, controlling the amount of oversize material production, power consumption, mill loading, noise and torque. In addition to the operational results, this challenge has consolidated a control team, with the participation of engineers and operators, diminishing the typical implementation time and achieving a greater use of the application in a short time."

Jan 1, 2010

By B. B. Broms

Embankment piles are common in the Scandinavian countries (Kjellman, 1940) and in Southeast Asia as support of fills, light structures, bridge abutments and deep excavations (Eide, 1968) as described in the following. Untreated timber piles are often used for light structures and shallow fills when the ground water level is high since they are inexpensive and readily available. When the applied loads are relatively high precast concrete piles and steel piles are preferred. DESIGN CONSIDERATIONS Embankment piles carry the load from a fill or a struc-ture either through skin friction along the sides of the piles (Fig. 1a) or through a precast concrete slab or through pile caps at the top of the piles (Fig. 1b). When the load is carried by skin friction it is often economical to use small diameter timber piles because of the large surface area (Asplund, 1939). For precast concrete or steel piles concrete caps are used to transfer the load to the piles due to the relatively high capacity of the piles since the skin friction resistance alone is not sufficient to transfer the load to the piles.

Jan 1, 2010

This sheet explains your audiogram (hearing test) and gives some basic information about protecting your hearing. Keep it so you can refer to it later. What is an audiogram? • An audiogram is often called a “hearing test,” but there’s no pass or fail • It is a written record of your hearing levels • A series of audiograms can track changes in hearing over time • Your hearing threshold levels (the quietest sounds you can hear) are measured in decibels (dB) at different frequencies from low (500 Hz) to high (8000 Hz) Why should I get audiograms? • To measure your hearing ability • To identify hearing problems • To monitor success at maintaining your hearing • To see if noise exposure is affecting your hearing Do I have normal hearing? Compare your hearing threshold levels to this scale: -10 – 25dB Normal hearing 26 – 40 dB Mild loss 41 – 55 dB Moderate loss 56 – 70 dB Moderate/severe loss 71 – 90 dB Severe loss 91 – 100dB Profound loss [ ]

Jan 1, 2008

A physical modelling study has been carried out to simulate the slag-metal dispersion induced by a high-strength bottom gas injection. Water and kerosene were utilized to simulate metal and slag respectively. A water model of CLU (Creusot-Loire Uddeholm)vessel was used with three different nozzle orientations, namely, off-centre, triangular off-centre and centre. The gas flow rates changed from 0.00599 m3/s to 0.01081 m3/s. Height of heavy and light phases was kept fixed at 0.23 m and 0.02 m respectively. The dispersed phase hold-up was determined at various axial and radial distances, gas flow rates, and tuyere configurations. The observations revealed that at a fixed gas injection rate, as the vertical distance increased in the centerline, straight off-centre orientation resulted in greater dispersed phase hold-up values than those of the centre configuration and the triangular off-centre orientation. The dispersed phase hold-up was found to increase with gas injection rate and decreased with axial distance. The variation of the dispersed phase hold-up with the dimensionless axial distance and the gas injection rate was correlated by using the modified Froude number. The experimental values of the dispersed phase hold-up were found to be in reasonable agreement with the correlated values obtained from the modelling equations. The findings of the present study may be utilized in the ferroalloy refining vessels in terms of designing tuyere locations for optimum processing conditions.

Jan 1, 2004

By R. P. H. Willis

For technology transfer to be successful a process, from research to full scale application, has to be followed. This paper describes such a process and how it is applied in practice. Some of the ?do?s? and ?don?ts? are highlighted. Recommendations are made on how to communicate existing knowledge and to ensure that a framework exists to effectively plan future projects with final technology transfer objectives firmly in place. The Impact Ripper System is used as a case study to illustrate lessons learned. Key words: Technology transfer, implementation

Jan 1, 2002

By Helmut Hass, Michael S. Shultz

For many tunneling, deep shaft and deep excavation projects ground freezing is one of the best if not the only technique available to create a watertight and load bearing temporary support system in soft ground conditions. When appropriate attention is given to the details of the ground freezing system design, ground freezing is a very safe method and is economically viable with competing techniques and combinations of techniques. Recent innovative uses of the technique in Europe are highlighted in this paper and compared with current uses in North America.

Jan 1, 2005

By H. I. Kim

The leaching of a complex matte in chlorine and chloride media was studied. The matte was prepared from manganese nodules by the reduction smelting-sulfidation route. From XRD analysis, the major phases of the matte were identified as CuFeS2, CuS2, (FeNi)9S8, (FeNi)S2, Ni9S8, Ni3S2, (CoFeNi)9S8 and Co metal. Investigated were the chlorine, hydrochloric acid, hydrochloric acid-oxygen, ferric chloride, ferric chloride-oxygen, cupric chloride and cupric chloride-oxygen systems. The results are discussed in terms of reagent concentration, retention time, leach temperature and gas sparging rate. The chlorination process resulted >99% metal extraction efficiency within a short retention time and at atmospheric temperature. However, there were no preferential extractions of Cu, Ni and Co with respect to Fe. The cupric chloride-oxygen system produced leach liquors with the lowest Fe content and with a high base-metal extraction. Sulfide sulfur was converted to mixtures of elemental sulfur and sulfate in all the studied systems.

Jan 1, 2009

By J. Coffin, R. Multani, C. Deredin

Glencore’s Strathcona Mill has recently evaluated a pyrrhotite depressant combination of diethylenetriamine (DETA) and sodium metabisulfite (SMBS) to improve its overall plant pyrrhotite- pentlandite (Po-Pn) selectivity, with the aim of producing a higher quality nickel concentrate. In a previous paper, key findings from a comprehensive lab-scale program (completed at the XPS Centre) were summarized where, of the depressants tested, DETA/SMBS combination was found to be the most effective in improving the Po-Pn selectivity. The present paper describes the metallurgical program recently completed at Strathcona Mill; DETA/SMBS evaluation on select plant “grab” samples as well as the major results of three DETA/SMBS plant trials conducted on several plant ore feeds (long-term testing). Interestingly, it was found that there was variable success in using DETA/SMBS depressants on the different plant ore feeds; DETA/SMBS (dosage: 25/50 g/t milled feed) on lower Cu feeds demonstrated a ~2% Ni recovery increase at the same Ni grade. On the other hand, higher Cu feeds demonstrated virtually no benefit from DETA/SMBS at the same plant dosage, suggesting that higher DETA/SMBS dosage (at specific locations) than that tested is required to overcome the increased Cu-DETA complexation for these particular feeds. Glencore Nickel – Sudbury Integrated Nickel Operations owns and operates Strathcona Mill which has been processing Ni-Cu ores from the Sudbury Basin since 1968. The valuable sulfides are pentlandite (Pn) – (Ni,Fe)9S8 and chalcopyrite (Cp) – CuFeS2, majority of the sulfide gangue is pyrrhotite (Po) – Fe(1-x)S [0 < x ≤ 0.125] which is present in two forms: hexagonal Po (Fe9S10) and monoclinic Po (Fe7S8) (Multani & Waters, 2017; Lawson et al., 2014). Currently Strathcona Mill processes ore mined from two primary sources from the Sudbury area and produces two concentrate streams: (1) nickel-copper concentrate that is sent to the Sudbury Smelter; and (2) copper concentrate that is shipped to the Fonderie Horne (Glencore Copper, Rouyn-Noranda).

Jan 1, 2019

By D. François-Bongarçon

When it comes to sampling theory, a bad sampler is a bad sampler, no matter what, and a sampler is either bad or good. It also is of critical economic importance to tell and understand the difference, especially in a metallurgical plant. In this paper, the grand principles of Sampling Theory are first recalled, then the most popular types of sample cutters for plants are critically reviewed. It is concluded that the industry has a lot of progresses to make in that direction, although improvements usually pay for themselves very quickly.

Jan 1, 2002

By I. G. Gonçalves

For most industrial minerals, the color is directly associated with economic value. In terms of physics, the principal property that defines the term ?color? is the intensity of light reflected (or transmitted) by an object over the visible band, comprehended between 400 and 700 nm. This reflectance spectrum serves as the starting point for a variety of color-describing factors, the most common in the mineral industry being the brightness (TAPPI, 1977 and 1986) and the L*a*b* system (HunterLab, 2008). Quality specifications for mineral products are usually based on these colorimetric parameters. This market is becoming increasingly more selective and demanding over the quality of raw materials and alongside the traditionally controlled characteristics, such as particle size distribution and chemical composition, a trend exists towards the establishment of increasingly more strict specifications for the optical properties of these materials. This is due to the fact that most plants consuming these industrial minerals incorporate them into products in which the visual appearance is controlled. For these plants, most of them being the manufacturers of plastics, paper, paints, and ceramics, variations in the color of mineral materials result in difficulties to achieve the right color in the final product. Therefore, these plants set strict specifications for colorimetric parameters such as whiteness and yellowness, as well as colorimetric coordinates like L*, a*, and b*. For the manufacturer of industrial minerals, this translates into difficulties simply because many of these parameters are usually alien to the tradition of the mining industry. The main quality parameter in the kaolin industry is brightness, which is a weighted average of reflectance values over the range of 400-510 nm (TAPPI, 1977). Due to the lack of a better property, producers tend to use brightness to also assess the quality of the in situ ore and along the processing operations. However, the unprocessed kaolin is often accompanied by ?contaminant? minerals. For Brazilian kaolins, which are the object of this study, the most important contaminants are hematite (Fe2O3), goethite (FeOOH), and anatase (TiO2). Each of these contaminant minerals has a distinct color and behaves differently during the processing of the kaolin ore. Hematite and goethite in particular are particularly strong pigmenting agents and at concentrations as low as 100 ppm they can make the difference between a high-quality white pigment product for paper coating and waste material. As each Fe-bearing contaminant has a different color and responds differently to processing operations (for example, magnetic separation, chemical bleaching, selective flocculation, and/or flotation in the case of kaolin), the in situ brightness tends to show a poor correlation with the brightness of the final product. Brightness measurements are sometimes complemented with X-Ray Fluorescence (XRF) analysis of Fe and Ti, but the total oxide content provided by XRF is also poorly correlated with product quality because Fe may be in the form of goethite, hematite, or inside the crystalline structure of kaolinite. Thus, a more robust technique capable of distinguishing each mineral phase is desirable. Diffuse reflectance spectroscopy has been used to analyze iron oxide/hydroxide content both qualitatively (Torrent and Barrón, 2003; Liu et al., 2011) and quantitatively (Jiet al., 2002 and 2006). These authors correlate slopes and inflection points at characteristic absorption bands with oxide/hydroxide content in natural soils. The approach presented here involves the extensive use of the Kubelka-Munk (K-M) theory, which has been used for color matching (Schabbachet al., 2009 and 2011) and particle size determination (Otsuka, 2004) in a simplified version. Unfortunately, the scattering constant S is very difficult to measure for dry powders, because the equations require a thin layer of material. Attempts have been made (Gonçalves and Petter, 2007, and Gonçalves, 2009) but the experimental errors tend to be high. Thus, this paper aims to develop a tool for the quantification of contaminant minerals in kaolin based on the K-M theory without resorting to measurements over thin layers. This tool is based on a new two-constant approach, which takes into account differences in scattering between materials over the whole measured spectrum. The experimental dataset consists of the reflectance spectra of mixtures between a bleached kaolin and synthetic Fe pigments.

Feb 27, 2013

The following observations on the mineral composition of the lead-zinc ores at Captain&apos;s Flat, New South Wales, are based upon the examination of a collection of specimens made during a brief visit to the mine in January, 1942, in conjunction with earlier studies of specimens and mill products, which have &apos;been the subject of various Mineragraphic Reports, Captain&apos;s Flat is about 35 miles south of Canberra, and is connected with the main line from Goulburn to Bombala by a branch line to Bungendore, 23 miles away from the mine.The geology of the mine has been described by Kenny and Mulholland2 and by Harper.3 The country consists of Silurian sediments, which have been invaded by a composite sill of quartz-felspar-porphyry. Both sediments and sill have been folded gently, the axial lines of the folds trending north and south. In the vicinity of the orebodies the folds are steeper, and thru,st faults are associated with the anticlines. The intense compression and shearing that accompanied the faulting has converted the adjacent porphyry to schist. The Captain&apos;s Flat orebodies occur along such a zone of shearing and faulting, on the eastern limb of a steep, north-pitching anticline. At their southern end the orebodies are enclosed in the slates underlying the porphyry, but the northerly pitch of the fold carries the slate to greater depth in the northern part of the mine, where the orebody lies beween schistose porphyry on the hanging wall and massive porphyry in the footwall.THE OREBODIESThe orebodies occur along a N.-S. strike length of 4,200 ft., and from the point of view of mining, fall into three sections: the Elliot&apos;s Section to the north, the Central Section, and the Keating&apos;s Section to the south. The Keating&apos;s Section is separated from the Central Section by 500-600 ft. of mineralised ground of so low a grade as&apos; to be called barren, and is offset about 125 ft. to the &apos;east of the Central body by an oblique fault striking N.300E. Elliot&apos;s Section and the Central Section are connected by persistent veins and stringers of lead-zinc ore, but although these are...

Jan 1, 1943

By D Craw, I M. Turnbull, R J. Norris, N Mortimer

The Otago Schist is being subdivided on a regional scale into structurally, metamorphically and lithologically distinct blocks. Differences between blocks are subtle, and difficult to map in the field. Boundaries are late-metamorphic or immediately post-metamorphic in origin, and are different from later brittle faults which disrupt the schist. Mapping of late-post-metamorphic structural discontinuities has direct application for basic grassroots exploration in the Otago Schist. The mineralised (and currently mined) Hyde-Macraes Shear Zone forms a regional scale boundary between a block dominated by politic schist and a block with massive psammitic schist, pelitic schist, and minor greenschist and chert. The HMSZ forms a metamorphic discontinuity, with garnet and biotite in the underlying schist, and neither index minerals apparent in the overlying schist. The HMSZ is also a structural boundary between domains with differing lineation orientations. The HMSZ can not yet be traced along strike to the northwest to the Rock and Pillar Range, where the only major discontinuities recognised are the Caples-Torlesse boundary and a normal fault separating low grade from high grade schist. Structural and lithological discontinuities in the Dunstan Range break the range up into distinct structural blocks, two of which are separated by the gold-mineralised Rise and Shine Shear Zone.

Jan 1, 1999

By R. Benito

This paper describes the application of modern data-analysis tools, such as data mining, to determine a representative cost driver for haulage activity. This cost driver was subsequently used to trace incurred haul costs by bench for openpit optimization. For this purpose, large amount of previously unused cost and production data from an open pit mine was extracted, loaded, transformed and integrated into a data warehouse. Predictive modeling was performed using Microsoft Decision Trees algorithm to compute expected unit haul costs by bench for future mine expansions. Finally, a sensitivity analysis was carried out to determine the effect of two cost drivers (if any) for incremental haul costs in the final pit outline process.

Jan 1, 2008

By Muir DM, Ritchie IM, Gibbons SL

Fundamental studies on the transformations of iron oxides have been carried out and related to the solution conditions in the Becher Process. The results show that a number of iron oxide interconversion reactions occur in the aeration reactor with the products depending on the pH, temperature and oxidation potential of the aeration liquor. It is concluded that the lack of process control in the aeration reactor of the Becher Process significantly hinders the ability to predict and produce high quality single phase iron oxides of a consistent colour.

Jan 1, 1989

By T. L. Johnston

The Dobbins property, about 4-1/2 miles northeast of Cartersville, Ga., was fist operated in 1866, it is the oldest manganese mine in Georgia and one of the oldest minus in the United States still producing manganese ore. Changes in ownership, lessees, and operators and lack of records prevent the compiling of statistics regarding total production of ore from the property.

Jan 1, 1942

By T. L. Johnston

The Dobbins property about 4-1/2 miles northeast of Cartersville, Ga., was first operated in 1866. It is the oldest manganese mine in Georgia and one of the oldest mines in the United States still producing manganese ore. Changes in ownership lessees and operators and lack of records prevent the compiling of statistics regarding total production of ore from the property

Jan 1, 1942

By J. Geyer, B. T. Burton, H. W. Newcomen

For open pits developed in tropical climates the upper portions of the pit walls are often located in residual soils and weathered rock. Due to the presence of relict structures, and the relatively low strength of the residual soils and weathered rock, design slope angles in these materials have to be developed by blending the results of kinematic assessments of geologic structures with rock mass stability analyses and traditional soil mechanics. Background information on the engineering considerations of residual soils are discussed, and the results of geotechnical assessments for proposed pit design of the Brisas del Cuyuni Project, located in southeastern Venezuela, are presented.

Jan 1, 2000

The Misima open pit gold mine is a 20Mt per annum operation. Blasthole drilling is used to sample all material at a uniform 5m square pattern, and representative sub- sampling of the blast holes enables assay samples to be collected over the full 10m bench height. Samples are assayed for gold, silver and copper at the Company&apos;s laboratory at the mine site and the assays are provided to geologists as a written assay report and on floppy disc. Surveyed blasthole locations and assay results are transferred via personal computers (PCs) to a SUN mini-computer where results are stored by bench, blasthole assays are kriged, and plot files are created. A geologist selects grade boundaries from the kriged data, adjusting the boundaries towards the raw blasthole data where hard boundaries are recognised. Surveyors peg the resultant boundaries in the pit using a system of colour-coded pegs to display the different material types. A daily plan also shows boundaries and face positions.

Jan 1, 1991